Analog Devices AD7723 b Datasheet

16-Bit, 1.2 MSPS

a

FEATURES
16-Bit Sigma-Delta ADC

1.2 MSPS Output Word Rate
32ⴛ/16ⴛ Oversampling Ratio
Low-Pass and Band-Pass Digital Filter

Linear Phase
On-Chip 2.5 V Voltage Reference
Standby Mode
Flexible Parallel or Serial Interface
Crystal Oscillator
Single 5 V Supply

AV

AGND

VIN(+)
VIN(–)

UNI

HALF_PWR

STBY

MODE 1

MODE 2

SYNC

DVDD/ CS

CFMT/RD

DGND/DRDY

DGND/DB0

CMOS, Sigma-Delta ADC

AD7723

FUNCTIONAL BLOCK DIAGRAM

FIR

FSI/
DB6

2.5V

REFERENCE

XTAL

CLOCK

SCO/

DB7

SDO/

DB8

DGND/

DB1

AD7723

MODULATOR

DGND/

DGND/

DB2

DB3

CONTROL

LOGIC

DOE/

SFMT/

DB4

FILTER

DB5

DD

REF2

REF1

DV

DD

DGND

XTAL_OFF

XTAL

CLKIN

DGND/DB15

DGND/DB14

SCR/DB13
SLDR/DB12
SLP/DB11
TSI/DB10
FSO/DB9

GENERAL DESCRIPTION

The AD7723 is a complete 16-bit, sigma-delta ADC. The part
operates from a 5 V supply. The analog input is continuously
sampled, eliminating the need for an external sample-and-hold.
The modulator output is processed by a finite impulse response
(FIR) digital filter. The on-chip filtering combined with a high
oversampling ratio reduces the external antialias requirements
to first order in most cases. The digital filter frequency response
can be programmed to be either low-pass or band-pass.

The AD7723 provides 16-bit performance for input bandwidths
up to 460 kHz at an output word rate up to 1.2 MHz. The
sample rate, filter corner frequencies, and output word rate are
set by the crystal oscillator or external clock frequency.

Data can be read from the device in either serial or parallel
format. A stereo mode allows data from two devices to share a
single serial data line. All interface modes offer easy, high speed
connections to modern digital signal processors.

The part provides an on-chip 2.5 V reference. Alternatively, an
external reference can be used.

A power-down mode reduces the idle power consumption to
200 µW.

The AD7723 is available in a 44-lead MQFP package and is speci­fied over the industrial temperature range from –40°C to +85°C.

Two input modes are provided, allowing both unipolar and
bipolar input ranges.

REV. B

Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties that
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: [phone] www.analog.com
Fax: [phone] © 2003 Analog Devices, Inc. All rights reserved.

(AVDD = DVDD = 5 V ⴞ 5%; AGND = AGND1 = AGND2 = DGND = 0 V;

1

f

AD7723–SPECIFICATIONS

= 19.2 MHz; REF2 = 2.5 V; TA = T

CLKIN

MIN

to T

, unless otherwise noted.)

MAX

B Version

Parameter Test Conditions/Comments Min Typ Max Unit

DYNAMIC SPECIFICATIONS

Decimate by 32

Bipolar Mode

Signal to Noise

Full Power 2.5 V Reference 87 90 dB

Half Power 86.5 89 dB
Total Harmonic Distortion
Spurious-Free Dynamic Range

Unipolar Mode

Signal to Noise 87 dB
Total Harmonic Distortion
Spurious-Free Dynamic Range

Band-Pass Filter Mode
Bipolar Mode

Signal to Noise 76 79 dB

Decimate by 16

Bipolar Mode

Signal to Noise Measurement Bandwidth = 0.383 × F

Signal to Noise Measurement Bandwidth = 0.5 × F
Total Harmonic Distortion

Spurious-Free Dynamic Range

Unipolar Mode

Signal to Noise Measurement Bandwidth = 0.383 × F
Signal to Noise Measurement Bandwidth = 0.5 × F
Total Harmonic Distortion

DIGITAL FILTER RESPONSE

Low-Pass Decimate by 32

0 kHz to f

/66.9 –3dB

f

CLKIN

/64 –6dB

f

CLKIN

/51.9 to f

f

CLKIN

/83.5 ± 0.001 dB

CLKIN

CLKIN

Group Delay 1293/2f
Settling Time 1293/f

Low-Pass Decimate by 16

0 kHz to f

/33.45 –3dB

f

CLKIN

/32 –6dB

f

CLKIN

/25.95 to f

f

CLKIN

/41.75 ± 0.001 dB

CLKIN

CLKIN

Group Delay 541/2f
Settling Time 541/f

Band-Pass Decimate by 32

/51.90 to f

f

CLKIN

/62.95, f

f

CLKIN

/64, f

f

CLKIN

0 kHz to f

CLKIN

CLKIN

/32 –6dB

CLKIN

/83.5, f

CLKIN

Group Delay 1293/2f
Settling Time 1293/f

Output Data Rate, F

O

Decimate by 32 f
Decimate by 16 f

ANALOG INPUTS

Full-Scale Input Span VIN(+) – VIN(–)

Bipolar Mode ± 4/5 × V
Unipolar Mode 08/5 × V

2, 3

HALF_PWR = 0 or 1

= 10 MHz When HALF_PWR = 1

f

CLKIN

3 V Reference 88.5 91 dB

4

4

2.5 V Reference –92 dB

–96 –90 dB

3 V Reference –90 dB

4

4

O

–89 dB
–90 dB

2.5 V Reference 82 86 dB
3 V Reference 83 87 dB

4

2.5 V Reference –88 dB
3 V Reference –86 dB

4

2.5 V Reference –90 dB

O

78 81.5 dB

3 V Reference –88 dB

O

4

O

84 dB
81 dB
–89 dB

/2 –90 dB

CLKIN

CLKIN

/2 –90 dB

CLKIN

CLKIN

/41.75 ± 0.001 dB

/33.34 –3dB

CLKIN

/25.95 to f

/2 –90 dB

CLKIN

CLKIN

CLKIN

/32

CLKIN

/16

CLKIN

REF2

REF2

V
V

–2–

REV. B

AD7723

B Version

Parameter Test Conditions/Comments Min Typ Max Unit

ANALOG INPUTS (Continued)

Absolute Input Voltage VIN(+) and/or VIN(–)AGND AV

DD

Input Sampling Capacitance 2pF
Input Sampling Rate, f

CLKIN

19.2 MHz

CLOCK

CLKIN Duty Ratio 45 55 %

REFERENCE

REF1 Output Resistance 3kΩ
Using Internal Reference

REF2 Output Voltage 2.39 2.54 2.69 V
REF2 Output Voltage Drift 60 ppm/°C

Using External Reference

REF2 Input Impedance REF1 = AGND 4 kΩ
REF2 External Voltage Range 1.2 2.5 3.15 V

STATIC PERFORMANCE

Resolution 16 Bits
Differential Nonlinearity Guaranteed Monotonic ±0.5 ±1 LSB
Integral Nonlinearity ±2 LSB
DC CMRR 80 dB
Offset Error ±20 mV
Gain Error

5

±0.5 % FSR

LOGIC INPUTS (Excluding CLKIN)

, Input High Voltage 2.0 V

V

INH

V

, Input Low Voltage 0.8 V

INL

CLOCK INPUT (CLKIN)

V

, Input High Voltage 3.8 V

INH

V

, Input Low Voltage 0.4 V

INL

ALL LOGIC INPUTS

, Input Current VIN = 0 V to DV

I

IN

DD

±10 µA

CIN, Input Capacitance 10 pF

LOGIC OUTPUTS

, Output High Voltage |I

V

OH

VOL, Output Low Voltage |I

| = 200 µA 4.0 V

OUT

| = 1.6 mA 0.4 V

OUT

POWER SUPPLIES

AV
I

AVDD

DD

HALF_PWR = Logic Low 50 60 mA

4.75 5.25 V

HALF_PWR = Logic High 25 33 mA

DV

DD

I

DVDD

Power Consumption

NOTES

1

Operating temperature range is as follows: B Version: – 40°C to +85°C.

2

Typical values for SNR apply for parts soldered directly to a printed circuit board ground plane.

3

Dynamic specifications apply for input signal frequencies from dc to 0.0240 × f

4

When using the internal reference, THD and SFDR specifications apply only to input signals above 10 kHz with a 10 µF decoupling capacitor between REF2 and
AGND2. At frequencies below 10 kHz, THD degrades to 84 dB and SFDR degrades to 86 dB.

5

Gain error excludes reference error.

6

CLKIN and digital inputs static and equal to 0 or DVDD.

Specifications subject to change without notice.

6

HALF_PWR = Logic Low 25 35 mA
HALF_PWR = Logic High 15 20 mA
Standby Mode 200 µW

in decimate by 16 Mode, and from dc to 0.0120 × f

CLKIN

4.75 5.25 V

in decimate by 32 Mode.

CLKIN

V

REV. B

–3–

AD7723

TIMING SPECIFICATIONS

(AVDD = DVDD = 5 V ⴞ 5%; AGND = AGND1 = DGND = 0 V; f
Logic Low or High, CFMT = Logic Low or High; TA = T

MIN

= 19.2 MHz; CL = 50 pF; SFMT =

CLKIN

to T

, unless otherwise noted.)

MAX

Parameter Symbol Min Typ Max Unit

CLKIN Frequency f
CLKIN Period (t

CLK

= 1/f

)t

CLK

CLKIN Low Pulse Width t
CLKIN High Pulse Width t
CLKIN Rise Time t
CLKIN Fall Time t

FSI Setup Time t
FSI Hold Time t
FSI High Time
CLKIN to SCO Delay t
SCO Period

1

2

, SCR = 1 t
SCO Period2, SCR = 0 t
SCO Transition to FSO High Delay t
SCO Transition to FSO Low Delay t
SCO Transition to SDO Valid Delay t
SCO Transition from FSI

3

SDO Enable Delay Time t
SDO Disable Delay Time t

DRDY High Time

2

Conversion Time2 (Refer to Tables I and II) t
CLKIN to DRDY Transition t
CLKIN to DATA Valid t

CS/RD Setup Time to CLKIN t
CS/RD Hold Time to CLKIN t

Data Access Time t
Bus Relinquish Time t

SYNC Input Pulse Width t
SYNC Low Time before CLKIN Rising t

DRDY High Delay after Rising SYNC t
DRDY Low Delay after SYNC Low t

NOTES

1

FSO pulses are gated by the release of FSI (going low).

2

Guaranteed by design.

3

Frame sync is initiated on the falling edge of CLKIN.

Specifications subject to change without notice.

CLK

1

2

3

4

5

6

7

t

8

9

10

10

11

12

13

t

14

15

16

t

17

18

19

20

21

22

23

24

25

26

27

28

119.2 MHz

0.052 1 µs

0.45 × t

0.45 × t

1

1

0.55 × t

0.55 × t

1

1

5ns
5ns

05ns
05ns

1t

CLK

25 40 ns
2t
1t

CLK

CLK

05 ns
05 ns
512 ns
60 t

CLK

+ t

2

520 ns
520 ns

2t
16/32 t

CLK

CLK

35 50 ns

20 35 ns
0ns
20 ns

20 35 ns

20 35 ns

1t

CLK

0ns

25 35 ns

2049 t

CLK

I

OL

1.6mA

TO

OUTPUT

PIN

50pF

C

L

I

OH

200␮A

1.6V

Figure 1. Load Circuit for Timing Specifications

–4–

REV. B

CLKIN

FSI

SCO

(SFMT = 1)

(CFMT = 0)

t

2.3V

5

0.8V

t

1

t

9

t

10

t

4

t

3

t

t

6

t

8

t

9

7

t

2

Figure 2. Serial Mode Timing for Clock Input, Frame Sync Input, and Serial Clock Output

32 CLKIN CYCLES

CLKIN

t

8

FSI

t

14

SCO

AD7723

t

11

FSO

(SFMT = 0)

t

11

FSO

(SFMT = 1)

SDO

t

12

t

13

D15 D14 D13 D2 D1 D0 D15 D14

Figure 3. Serial Mode 1. Timing for Frame Sync Input, Frame Sync Output, Serial Clock Output, and Serial Data Output
(Refer to Table I for Control Inputs, TSI = DOE)

32 CLKIN CYCLES

CLKIN

t

8

FSI

t

SCO

(CFMT = 0)

FSO

14

t

11

t

12

t

13

SDO

D2 D1 D0 D15 D14 D13 D12 D11 D5

D3 D2 D1 D0 D15 D14

D4

Figure 4. Serial Mode 2. Timing for Frame Sync Input, Frame Sync Output, Serial Clock Output, and Serial Data Output
(Refer to Table I for Control Inputs, TSI = DOE)

REV. B

–5–

AD7723

16 CLKIN CYCLES

CLKIN

t

8

FSI

t

SCO

(CFMT = 0)

FSO

SDO

Figure 5. Serial Mode 3. Timing for Frame Sync Input, Frame Sync Output, Serial Clock Output, and Serial Data Output
(Refer to Table I for Control Inputs, TSI = DOE)

14

t

11

t

13

D2 D1 D0 D15 D14 D13 D12 D11 D5 D4 D3 D2 D1 D0 D15 D14

t

12

Table I. Serial Interface (MODE1 = 0, MODE2 = 0)

Decimation Digital Filter SCO Frequency Output Data Control Inputs

Serial Mode Ratio (SLDR) Mode (SLP) (SCR) Rate SLDR SLP SCR

f

132Low-Pass f
132Band-Pass f
232Low-Pass f
232Band-Pass f
316Low-Pass f

CLKIN

CLKIN

/2 f

CLKIN

/2 f

CLKIN

CLKIN

/32 1 1 0

CLKIN

f

/32 1 0 0

CLKIN

/32 1 1 1

CLKIN

/32 1 0 1

CLKIN

f

/16 0 1 0

CLKIN

Table II. Parallel Interface

Digital Filter Decimation Output Control Inputs
Mode Ratio Data Rate MODE1 MODE2

Band-Pass 32 f
Low-Pass 32 f
Low-Pass 16 f

DOE

t

15

SDO

/32 0 1

CLKIN

/32 1 0

CLKIN

/16 1 1

CLKIN

t

16

Figure 6. Serial Mode Timing for Data Output Enable and Serial Data Output

–6–

REV. B

CLKIN

DRDY

AD7723

t

18

t

t

19

t

17

t

20

19

DB0–DB15

CLKIN

DRDY

RD/CS

DB0–DB15

WORD N – 1

WORD N

Figure 7a. Parallel Mode Read Timing, CS and

t

19

t

22

t

t

t

21

22

t

23

21

VALID DATA

t

24

Figure 7b. Parallel Mode Read Timing, CS =

WORD N + 1

RD

Tied Logic Low

t

18

t

19

RD

REV. B

CLKIN

SYNC

DRDY

t

28

t

26

t

25

t

27

Figure 8. SYNC Timing

–7–

AD7723

ABSOLUTE MAXIMUM RATINGS*

(TA = 25°C, unless otherwise noted.)

DVDD to DGND . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V

AV
AV

DD

DD

, AV
, AV

to AGND . . . . . . . . . . . . . . . . . –0.3 V to +7 V

DD1

to DVDD . . . . . . . . . . . . . . . . . . . –1 V to +1 V

DD1

AGND, AGND1 to DGND . . . . . . . . . . . . –0.3 V to +0.3 V

Digital Inputs to DGND . . . . . . . . . –0.3 V to DV

+ 0.3 V

DD

Model Range Description Option

AD7723BS –40°C to +85°C MQFP S-44-2
AD7723BS-REEL –40°C to +85°C MQFP S-44-2
EVAL-AD7723CB Evaluation Board

ORDERING GUIDE

Temperature Package Package

Digital Outputs to DGND . . . . . . . . –0.3 V to DVDD + 0.3 V

VIN(+), VIN(–) to AGND . . . . . . . . –0.3 V to AV

REF1 to AGND . . . . . . . . . . . . . . . . –0.3 V to AV

+ 0.3 V

DD

+ 0.3 V

DD

REF2 to AGND . . . . . . . . . . . . . . . . –0.3 V to AVDD + 0.3 V

Operating Temperature Range . . . . . . . . . . –40°C to +85°C

Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C

Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . 150°C

Thermal Impedance . . . . . . . . . . . . . . . . . . . . . . . 95°C/W

θ

JA

Lead Temperature, Soldering

Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . . . 215°C

Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220°C

*Stresses above those listed under Absolute Maximum Ratings may cause perma-

nent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.

CAUTION

ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the AD7723 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.

WARNING!

ESD SENSITIVE DEVICE

DGND/DB2

DGND/DB1

DGND/DB0

CFMT/RD

DGND/DRDY

DGND

MODE2

MODE1

AGND1

AGND1

AV

DD1

PIN CONFIGURATION

DOE/DB4

DGND/DB3

SFMT/DB5

42

4344 36 35 3437

1

PIN 1
IDENTIFIER

2

3

4

5

6

7

8

9

10

11

12 13 14 15 16 17 18 1 92021 2 2

XTAL

CLKIN

XTAL_OFF

DD

FSI/DB6

SCO/DB7

DV

40 39 3841

AD7723

TOP VIEW

(Not to Scale)

DD

AV

AGND

HALF_PWR

SDO/DB8

AGND

FSO/DB9

VIN(–)

TSI/DB10

VIN(+)

SLP/DB11

REF1

SLDR/DB12

33

32

31

30

29

28

27

26

25

24

23

AGND2

SCR/DB13

DGND/DB14

DGND/DB15

DVDD/CS

SYNC

DGND

STBY

AV

DD

AGND

UNI

REF2

–8–

REV. B