Analog Devices AD7719EB, AD7719BRU, AD7719BR Datasheet

Low Voltage, Low Power,

a

Factory-Calibrated 16-/24-Bit Dual - ADC

FEATURES
HIGH RESOLUTION - ADCs
Two Independent ADCs (16- and 24-Bit Resolution)
Factory-Calibrated (Field Calibration Not Required)
Output Settles in One Conversion Cycle (Single

Conversion Mode)
Programmable Gain Front End
Simultaneous Sampling and Conversion of Two

Signal Sources
Separate Reference Inputs for Each Channel
Simultaneous 50 Hz and 60 Hz Rejection at 20 Hz

Update Rate

ISOURCE Select

TM

24-Bit No Missing Codes—Main ADC
13-Bit p-p Resolution @ 20 Hz, 20 mV Range
18-Bit p-p Resolution @ 20 Hz, 2.56 V Range

INTERFACE
3-Wire Serial

TM

, QSPITM, MICROWIRETM and DSP-Compatible

SPI
Schmitt Trigger on SCLK

POWER
Specified for Single 3 V and 5 V Operation
Normal: 1.5 mA Typ @ 3 V
Power-Down: 10 A (32 kHz Crystal Running)

ON-CHIP FUNCTIONS
Rail-Rail Input Buffer and PGA
4-Bit Digital I/O Port
On-Chip Temperature Sensor
Dual Switchable Excitation Current Sources

FUNCTIONAL BLOCK DIAGRAM

IOUT1

DV

DD

IEXC1
200A

AV

DD

IEXC2
200A

DGND

AD7719

AD7719

Low-Side Power Switches
Reference Detect Circuit

APPLICATIONS
Sensor Measurement
Temperature Measurement
Pressure Measurements
Weigh Scales
Portable Instrumentation
4–20 mA Transmitters

GENERAL DESCRIPTION

The AD7719 is a complete analog front end for low frequency
measurement applications. It contains two high resolution sigma­delta ADCs, switchable matched excitation current sources,
low-side power switches, digital I/O port, and temperature
sensor. The 24-bit main channel with PGA accepts fully differen­tial, unipolar, and bipolar input signal ranges from 1.024 ×
REFIN1/128 to 1.024 × REFIN1. Signals can be converted
directly from a transducer without the need for signal condi­tioning. The 16-bit auxiliary channel has an input signal range
of REFIN2 or REFIN2/2.

The device operates from a 32 kHz crystal with an on-chip
PLL generating the required internal operating frequency. The
output data rate from the part is software programmable. The
peak-to-peak resolution from the part varies with the programmed
gain and output data rate.

The part operates from a single 3 V or 5 V supply. When oper­ating from 3 V supplies, the power dissipation for the part is

4.5 mW with both ADCs enabled and 2.85 mW with only the
main ADC enabled in unbuffered mode. The AD7719 is housed
in 28-lead SOIC and TSSOP packages.

XTAL1 XTAL2REFIN1(+) REFIN1(–)

REFERENCE

DETECT

OSC. AND

PLL

IOUT2

AIN1

AIN2
AIN3
AIN4

AIN5
AIN6

ISOURCE Select is a trademark of Analog Devices.
SPI and QSPI are trademarks of Motorola Inc.
MICROWIRE is a trademark of National Semiconductor Corporation.

MUX1

MUX2

AV

MUX

DD

AV

DD

AGND

BUF

TEMP

SENSOR

PGA

AUXILIARY CHANNEL

AGND REFIN2 PWRGND P1/SW1 P2/SW2 P3 P4

REV. 0

Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties that
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices.

MAIN CHANNEL
24-BIT - ADC

AV

DD

I/O PORT

16-BIT - ADC

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: [phone] www.analog.com
Fax: [phone] © Analog Devices, Inc., 2001

SERIAL

INTERFACE

AND

CONTROL

LOGIC

DOUT
DIN
SCLK

CS
RDY
RESET

AD7719

TABLE OF CONTENTS

FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . 1

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . 6

ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

TIMING CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . 7

DIGITAL INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

PIN CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

PIN FUNCTION DESCRIPTIONS . . . . . . . . . . . . . . . . . . 9

TYPICAL PERFORMANCE CHARACTERISTICS . . . . 11

DUAL-CHANNEL ADC CIRCUIT INFORMATION . . . 12

Main Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Auxiliary Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Both Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

MAIN AND AUXILIARY ADC NOISE

PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

ON-CHIP REGISTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Communications Register

(A3, A2, A1, A0 = 0, 0, 0, 0) . . . . . . . . . . . . . . . . . . . . 19

Status Register (A3, A2, A1, A0 = 0, 0, 0, 0;

Power–On Reset = 00 Hex) . . . . . . . . . . . . . . . . . . . . . 20

Mode Register (A3, A2, A1, A0 = 0, 0, 0, 1;

Power-On-Reset = 00 Hex) . . . . . . . . . . . . . . . . . . . . . 21

Operating Characteristics when Addressing the Mode

and Control Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Main ADC Control Register (AD0CON):

(A3, A2, A1, A0 = 0, 0, 1, 0;

Power-On Reset = 07 Hex) . . . . . . . . . . . . . . . . . . . . . 22

Aux ADC Control Registers (AD1CON):

(A3, A2, A1, A0 = 0, 0, 1, 1;

Power-On Reset = 01 Hex) . . . . . . . . . . . . . . . . . . . . . 23

Filter Register (A3, A2, A1, A0 = 0, 1, 0, 0;

Power-On Reset = 45 Hex) . . . . . . . . . . . . . . . . . . . . . 24

I/O and Current Source Control Register (IOCON):

(A3, A2, A1, A0 = 0, 1, 1, 1;

Power-On Reset = 0000 Hex) . . . . . . . . . . . . . . . . . . . 24

Main ADC Data Result Registers (DATA0):

(A3, A2, A1, A0 = 0, 1, 0, 1;

Power-On Reset = 000000 Hex) . . . . . . . . . . . . . . . . . 26

Aux ADC Data Result Registers (DATA1):

(A3, A2, A1, A0 = 0, 1, 1, 0;

Power-On Reset = 0000 Hex) . . . . . . . . . . . . . . . . . . . 26

Main ADC Offset Calibration Coefficient Registers (OF0):

(A3, A2, A1, A0 = 1, 0, 0, 0;

Power-On Reset = 800000 Hex) . . . . . . . . . . . . . . . . . 26

Aux ADC Offset Calibration Coefficient Registers (OF1):

(A3, A2, A1, A0 = 1, 0, 0, 1;

Power-On Reset = 8000 Hex) . . . . . . . . . . . . . . . . . . . 26

Main ADC Gain Calibration Coefficient Registers (GNO):

(A3, A2, A1, A0 = 1, 0, 1, 0;

Power-On Reset = 5XXXX5 Hex) . . . . . . . . . . . . . . . . 25

Aux ADC Gain Calibration Coefficient Registers (GN1):

(A3, A2, A1, A0 = 1, 0, 1, 1;

Power-On Reset = 59XX Hex) . . . . . . . . . . . . . . . . . . . 26

ID Register (ID): (A3, A2, A1, A0 = 1, 1, 1, 1;

Power-On Reset = 0X Hex) . . . . . . . . . . . . . . . . . . . . . 26

User Nonprogrammable Test Registers . . . . . . . . . . . . . . 26

CONFIGURING THE AD7719 . . . . . . . . . . . . . . . . . . . . . 27

MICROCOMPUTER/MICROPROCESSOR

INTERFACING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

AD7719-to-68HC11 Interface . . . . . . . . . . . . . . . . . . . . . 28

AD7719-to-8051 Interface . . . . . . . . . . . . . . . . . . . . . . . . 28

AD7719-to-ADSP-2103/ADSP-2105 Interface . . . . . . . . 30

CIRCUIT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . 30

Analog Input Channels . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Programmable Gain Amplifier . . . . . . . . . . . . . . . . . . . . . 32

Bipolar/Unipolar Configuration . . . . . . . . . . . . . . . . . . . . 33

Data Output Coding . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Burnout Currents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Excitation Currents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Crystal Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Reference Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Reference Detect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Reset Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Power-Down Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Idle Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

ADC Disable Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Grounding and Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

APPLICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Pressure Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Temperature Measurement . . . . . . . . . . . . . . . . . . . . . . . 37

3-Wire RTD Configurations . . . . . . . . . . . . . . . . . . . . . . 38

Smart Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . 40

–2–

REV. 0

AD7719–SPECIFICATIONS

REFIN(+) = 2.5 V; REFIN(–) = AGND; AGND = DGND = 0 V; XTAL1/XTAL2 = 32.768 kHz Crystal; all specifications T

Parameter AD7719B Unit Test Conditions

ADC CHANNEL SPECIFICATION

Output Update Rate 5.4 Hz min Both Channels Synchronized

MAIN CHANNEL

No Missing Codes

2

Resolution 13 Bits p-p ±20 mV Range, 20 Hz Update Rate

Output Noise and Update Rates See Tables II to V
Integral Nonlinearity ±10 ppm of FSR max Typically 2 ppm.
Offset Error
Offset Error Drift vs. Temperature
Full-Scale Error
Gain Drift vs. Temperature

3

5, 8, 9

4

Power Supply Rejection (PSR) 80 dB min Input Range = ± 2.56 V, 100 dB typ.

ANALOG INPUTS

Differential Input Voltage Ranges ±1.024 × REFIN1/GAIN V nom REFIN1 = REFIN1(+) – REFIN1(–)

ADC Range Matching ±2 µV typ Input Voltage = 19 mV on All Ranges
Absolute AIN Voltage Limits AGND + 100 mV V min BUF = 0; Buffered Mode of Operation

Analog Input Current

2

DC Input Current ± 1 nA max
DC Input Current Drift ± 5 pA /°C typ

Absolute AIN Voltage Limits AGND – 30 mV V min BUF = 1; Unbuffered mode of operation.

Analog Input Current BUF = 1. Unbuffered Mode of Operation.

DC Input Current ± 125 nA/V typ Input Current Varies with Input Voltage
DC Input Current Drift ± 2 pA/V/°C typ

Normal-Mode Rejection

2, 6

@ 50 Hz 100 dB min
@ 60 Hz 100 dB min 60 Hz ± 1 Hz, 20 Hz Update Rate, SF = 68

Common-Mode Rejection

@ DC 90 dB min Input Range = ± 2.56 V, AIN = 1 V.

@ 50 Hz
@ 60 Hz

2

2

REFERENCE INPUT (REFIN1)

REFIN1 Voltage 2.5 V nom REFIN1 = REFIN1(+) – REFIN1(–)
REFIN1 Voltage Range

2

REFIN1 Common-Mode Range AGND – 30 mV V min

Reference DC Input Current 0.5 µA/V typ
Reference DC Input Current Drift ±0.01 nA/V/°C typ
Normal-Mode Rejection

2, 6

@ 50 Hz 100 dB min 50 Hz ± 1 Hz, SF = 82
@ 60 Hz 100 dB min 60 Hz ± 1 Hz, SF = 68

Common-Mode Rejection

@ DC 110 dB typ Input Range = ± 2.56 V, AIN = 1 V
@ 50 Hz 110 dB typ 50 Hz ± 1 Hz, Range = 2.56 V, AIN = 1 V
@ 60 Hz 110 dB typ 60 Hz ± 1 Hz, Range = 2.56 V, AIN = 1 V

Reference Detect Levels 0.3 V min NOXREF Bit Active if VREF < 0.3 V

AUXILIARY CHANNEL

No Missing Codes

2

Resolution 16 Bits p-p ±2.5 V Range, 20 Hz Update Rate
Output Noise and Update Rates See Tables VI and VIII
Integral Nonlinearity ±15 ppm of FSR max

105 Hz max 0.732 ms Increments

24 Bits min 20 Hz Update Rate

18 Bits p-p ±2.56 V Range, 20 Hz Update Rate

±3 µV typ

4

±10 nV/°C typ
±10 µV typ At the Calibrated Conditions
±0.5 ppm/°C typ

AV

DD

AV

DD

100 dB min 50 Hz ± 1 Hz, Range = ± 2.56 V, AIN = 1 V
100 dB min 60 Hz ± 1 Hz, Range = ± 2.56 V, AIN = 1 V

1 V min
AV

DD

AV

DD

0.65 V max NOXREF Bit Inactive if VREF > 0.65 V

16 Bits min

(AVDD = 2.7 V to 3.6 V or 4.75 V to 5.25 V, DVDD = 2.7 V to 3.6 V or 4.75 V to 5.25 V,

to T

MIN

110 dB typ on ±20 mV Range

GAIN = 1 to 128.

– 100 mV V max

BUF = 0

+ 30 mV V max

50 Hz ± 1 Hz, 16.65 Hz Update Rate, SF = 82

100 dB typ. 110 dB typ on ± 20 mV Range

V max

+ 30 mV V max

unless otherwise noted.)

MAX

FSR

=

×2 1 024 1.

REFIN

Gain

1

REV. 0

–3–

AD7719

Parameter AD7719B Unit Test Conditions

AUXILIARY CHANNEL (continued)

Offset Error
Offset Error Drift vs. Temperature
Full-Scale Error
Gain Drift vs. Temperature
Negative Full-Scale Error ±1 LSB typ
Power Supply Rejection (PSR) 70 dB min AIN = 1 V Input Range = ±2.5 V, Typically 80 dB

ANALOG INPUTS

Differential Input Voltage Ranges ±REFIN2 V nom ARN = 1

Absolute AIN Voltage Limits AGND – 30 mV V min Unbuffered Input

Analog Input Current

DC Input Current ± 125 nA/V typ Input Current Varies with Input Voltage
DC Input Current Drift ± 2 pA/V/°C typ

Normal-Mode Rejection

@ 50 Hz 100 dB min 50 Hz ± 1 Hz, SF = 82
@ 60 Hz 100 dB min 60 Hz ± 1 Hz, SF = 68

Common-Mode Rejection

@ DC 85 dB min Input Range = ± 2.5 V, AIN = 1 V
@ 50 Hz
@ 60 Hz

REFERENCE INPUT (REFIN2) With Respect to AGND

REFIN2 Voltage 2.5 V nom
REFIN2 Range

Reference DC Input Current
Reference DC Input Current Drift 0.003 nA/V/°C typ

EXCITATION CURRENT SOURCES

(IEXC1 and IEXC2)

Output Current 200 µA nom
Initial Tolerance at 25°C ± 10 % typ
Drift 20 ppm/°C typ
Initial Current Matching at 25°C ±1 % typ Matching between IEXC1 and IEXC2

Drift Matching 1 ppm/°C typ
Line Regulation (AV
Load Regulation 300 nA/V typ
Output Compliance AVDD – 0.6 V max

LOW-SIDE POWER SWITCHES

(SW1 AND SW2)

R

Allowable Current

TEMPERATURE SENSOR

Accuracy See TPC 5 °C typ

TRANSDUCER BURNOUT

AIN(+) Current –100 nA typ
AIN(–) Current +100 nA typ
Initial Tolerance @ 25°C ±15 % typ
Drift 0.03 %/°C typ

SYSTEM CALIBRATION

Full-Scale Calibration Limit 1.05 × FS
Zero-Scale Calibration Limit –1.05 × FS V min
Input Span 0.8 × FS V min

ON

3

8, 9

4

±3 µV typ Selected Channel = AIN5/AIN6

4

±10 nV/°C typ
±0.75 LSB typ

0.5 ppm/°C typ

±REFIN2/2 V nom ARN = 0

+ 30 mV V max

AV

DD

2, 6

2

2

2

2

90 dB min 50 Hz ± 1 Hz, Range = 2.5 V, AIN = 1 V
90 dB min 60 Hz ± 1 Hz, Range = 2.5 V, AIN = 1 V

1 V min
AV

DD

V max

0.2 µA/V typ

No Load

) 2.1 µA/V max AVDD = 5 V ± 5%. Typically 1.25 µA/V

DD

AGND –30 mV V min

5 Ω max AVDD = 5 V. Typically 3 Ω

2

10, 2

7 Ω max AV
20 mA max Continuous Current per Switch

11

V max

= 3 V. Typically 4.5 Ω

DD

2.1 × FS V max

–4–

REV. 0

AD7719–SPECIFICATIONS

1

Parameter AD7719B Unit Test Conditions

LOGIC INPUTS

All Inputs Except SCLK and XTAL1

V

, Input Low Voltage 0.8 V max DVDD = 5 V

INL

V

, Input High Voltage 2.0 V min DVDD = 3 V or 5 V

INH

SCLK Only (Schmitt-Triggered Input)

V

T(+)

V

T(–)

V

– V

T(+)

V
V
V

XTAL1 Only

V
V
V
V

T(–)

T(+)

T(–)

– V

T(+)

T(–)

2

, Input Low Voltage 0.8 V max DVDD = 5 V

INL

, Input High Voltage 3.5 V min DVDD = 5 V

INH

, Input Low Voltage 0.4 V max DVDD = 3 V

INL

, Input High Voltage 2.5 V min DVDD = 3 V

INH

Input Currents ±10 µA max VIN = DV

Input Capacitance

LOGIC OUTPUTS (Excluding XTAL2)

V

, Output High Voltage

OH

VOL, Output Low Voltage
V

, Output High Voltage

OH

VOL, Output Low Voltage

2

2

2

2

2

Floating-State Leakage Current ±10 µA max
Floating-State Output Capacitance ±10 pF typ
Data Output Coding Binary Unipolar Mode

I/O PORT

V

V

7

, Input Low Voltage

INL

, Input High Voltage

INH

2

2

Input Currents ±10 µA max V

Input Capacitance 10 pF typ All Digital Inputs
V

, Output High Voltage

OH

VOL, Output Low Voltage
V

, Output High Voltage

OH

VOL, Output Low Voltage

2

2

2

2

Floating-State Output Leakage Current ±10 µA max
Floating-State Output Capacitance ±10 pF typ

START-UP TIME

From Power-On 300 ms typ
From Idle Mode 1 ms typ
From Power-Down Mode 1 ms typ Osc. Active in Power-Down

POWER REQUIREMENTS

Power Supply Voltages

AV

– AGND 2.7/3.6 V min/max AVDD = 3 V nom

DD

DVDD – DGND 2.7/3.6 V min/max DVDD = 3 V nom

Power Supply Currents

DI

Current (Normal Mode)

DD

2

0.4 V max DVDD = 3 V

2

1.4/2 V min/V max DVDD = 5 V

0.8/1.4 V min/V max DVDD = 5 V

0.3/0.85 V min/V max DVDD = 5 V

0.95/2 V min/V max DVDD = 3 V

0.4/1.1 V min/V max DVDD = 3 V

0.3/0.85 V min/V max DVDD = 3 V

–70 µA max VIN = DGND, Typically –40 µA at 5 V

DD

and –20 µA at 3 V

10 pF typ All Digital Inputs

DVDD – 0.6 V min DVDD = 3 V, I

0.4 V max DVDD = 3 V, I
4 V min DVDD = 5 V, I

0.4 V max DVDD = 5 V, I

SOURCE

= 100 µA

SINK

SOURCE

= 1.6 mA

SINK

= 100 µA

= 200 µA

Offset Binary Bipolar Mode

I/O Port Voltages Are with Respect to
AV

and AGND

DD

0.8 V max AVDD = 5 V

0.4 V max AV

DD

= 3 V

2.0 V min AVDD = 3 V or 5 V
= AV

IN

DD

–70 µA max VIN = AGND, Typically –40 µA at AVDD = 5 V

and –20 µA at AV

AVDD – 0.6 V min AVDD = 3 V, I

0.4 V max AVDD = 3 V, I

4 V min AVDD = 5 V, I

0.4 V max AVDD = 5 V, I

DD

SOURCE

= 100 µA

SINK

SOURCE

= 1.6 mA

SINK

= 3 V

= 100 µA

= 200 µA

300 ms typ Osc. Powered Down

4.75/5.25 V min/max AV

4.75/5.25 V min DV

12

0.6 mA max DVDD = 3 V, 0.5 mA typ

= 5 V nom

DD

= 5 V nom

DD

0.75 mA max DVDD = 5 V, 0.6 mA typ

REV. 0

–5–

AD7719

Parameter AD7719B Unit Test Conditions

Power Supply Currents (Continued)

AI

Current (Main ADC) 1.1 mA max AVDD = 3 V or 5 V, Buffered Mode,

DD

0.55 mA max AV

AI

Current (Aux ADC) 0.3 mA max AVDD = 3 V or 5 V, 0.25 mA typ

DD

AI

Current (Main and Aux ADC) 1.25 mA max AVDD = 3 V or 5 V, Main ADC Buffered,

DD

DI

(ADC Disable Mode)

DD

13

0.35 mA max DVDD = 3 V, 0.25 mA typ

0.4 mA max DV

AI

(ADC Disable Mode) 0.15 mA max AVDD = 3 V or 5 V

DD

DI

(Power-Down Mode) 10 µA max DVDD = 3 V, 32.768 kHz Osc. Running

DD

2 µA max DV
30 µA max DV
8 µA max DV

AIDD (Power-Down Mode) 1 µA max AVDD = 3 V or 5 V

NOTES

1

Temperature Range –40°C to +85°C.

2

Guaranteed by design and/or characterization data on production release.

3

System zero calibration will remove this error.

4

A calibration at any temperature will remove this drift error.

5

The Main ADC is factory-calibrated with AVDD = DVDD = 4 V, TA = 25°C, REFIN1(+) – REFIN1(–) = 2.5 V. If the user power supplies or temperature conditions
are significantly different from these, internal full-scale calibration will restore this error to the published specification. System calibration can be used to reduce this
error to the order of the noise. Full scale error applies to both positive and negative full scale.

6

Simultaneous 50 Hz and 60 Hz rejection is achieved using 19.8 Hz (SF = 69) update rate. Normal mode rejection in this case is 60 dB min.

7

Input and Output levels on the I/O Port are with respect to AVDD and AGND.

8

A system full-scale calibration will remove this error.

9

A typical gain error of ± 10µV results following a user self calibration.

10

After a calibration if the analog input exceeds positive full scale, the converter will output all 1s. If the analog input is less than negative full scale then the device will
output all 0s.

11

FS = Full-Scale Input. FS = 1.024 × REFIN1/Gain on the Main ADC, where REFIN1 = REFIN1(+) – REFIN1(–). FS = REFIN2 on the aux ADC when ARN = 1
in the aux ADC control register (AD1CON) and REFIN2/2 on the aux ADC when ARN = 0.

12

Normal Mode refers to the case where both main and aux ADCs are running.

13

ADC disable is entered by setting both the AD0EN and AD1EN bits in the Main and Aux ADC control registers to a 0 and setting the mode bits (MD2, MD1,
MD0) in the Mode register to non-0.

Specifications subject to change without notice.

0.85 mA typ
= 3 V or 5 V, Unbuffered Mode,

DD

0.45 mA typ

1 mA typ

= 5 V, 0.3 mA typ

DD

= 3 V, Oscillator Powered Down

DD

= 5 V, 32.768 kHz Osc. Running

DD

= 5 V, Oscillator Powered Down

DD

ABSOLUTE MAXIMUM RATINGS

(TA = 25°C unless otherwise noted)

1

AVDD to AGND . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V

AV

to DGND . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V

DD

DV

to AGND . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V

DD

to DGND . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V

DV

DD

AGND to DGND

2

. . . . . . . . . . . . . . . . . . . –20 mV to +20 mV

PWRGND to AGND . . . . . . . . . . . . . . . . –20 mV to +20 mV

to DVDD . . . . . . . . . . . . . . . . . . . . . . . . . . –5 V to +5 V

AV

DD

Analog Input Voltage to AGND . . . . –0.3 V to AV

Reference Input Voltage to AGND . . –0.3 V to AV

+0.3 V

DD

+0.3 V

DD

Total AIN/REFIN Current (Indefinite) . . . . . . . . . . . . 30 mA

Digital Input Voltage to DGND . . . . –0.3 V to DV

Digital Output Voltage to DGND . . . –0.3 V to DV

+0.3 V

DD

+0.3 V

DD

Operating Temperature Range . . . . . . . . . . . –40°C to +85°C

Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C

ORDERING GUIDE

Model Temperature Range Package Description Package Option

AD7719BR –40°C to +85°C SOIC R-28
AD7719BRU –40°C to +85°C TSSOP RU-28
EVAL-AD7719EB Evaluation Board

Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C

SOIC Package

Thermal Impedance . . . . . . . . . . . . . . . . . . . . 71.4°C/W

θ

JA

θ

Thermal Impedance . . . . . . . . . . . . . . . . . . . . . . 23°C/W

JC

TSSOP Package

Thermal Impedance . . . . . . . . . . . . . . . . . . . . 97.9°C/W

θ

JA

θ

Thermal Impedance . . . . . . . . . . . . . . . . . . . . . . 14°C/W

JC

Lead Temperature, Soldering

Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . . . . 215°C

Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220°C

NOTES

1

Stresses above those listed under Absolute Maximum Ratings may cause perma-

nent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those listed in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.

2

AGND and DGND and connected internally within the AD7719.

–6–

REV. 0

TIMING CHARACTERISTICS

WARNING!

ESD SENSITIVE DEVICE

5.25 V; AGND = DGND = 0 V; X

= 32.768 kHz; Input Logic 0 = 0 V, Logic 1 = DVDD unless otherwise noted.)

TAL

1, 2

(AVDD = 2.7 V to 3.6 V or AVDD = 4.75 V to 5.25 V; DVDD = 2.7 V to 3.6 V or DVDD = 4.75 V to

AD7719

Limit at T

MIN

, T

MAX

Parameter (B Version) Unit Conditions/Comments

t

1

t

2

32.768 kHz typ Crystal Oscillator Frequency.
50 ns min RESET Pulsewidth

Read Operation

t

3

t

4

4

t

5

0 ns min RDY to CS Setup Time
0 ns min CS Falling Edge to SCLK Active Edge Setup Time
0 ns min SCLK Active Edge to Data Valid Delay

3

3

60 ns max DVDD = 4.75 V to 5.25 V

4, 5

t

5A

80 ns max DV
0 ns min CS Falling Edge to Data Valid Delay

= 2.7 V to 3.6 V

DD

3

60 ns max DVDD = 4.75 V to 5.25 V
80 ns max DV

t

6

t

7

t

8

6

t

9

100 ns min SCLK High Pulsewidth
100 ns min SCLK Low Pulsewidth
0 ns min CS Rising Edge to SCLK Inactive Edge Hold Time
10 ns min Bus Relinquish Time after SCLK Inactive Edge
80 ns max

t

10

100 ns max SCLK Active Edge to RDY High

Write Operation

t

11

t

12

t

13

t

14

t

15

t

16

NOTES

1

Sample tested during initial release to ensure compliance. All input signals are specified with tR = tF = 5 ns (10% to 90% of DVDD) and timed from a voltage level of 1.6 V.

2

See Figures 2 and 3.

3

SCLK active edge is falling edge of SCLK.

4

These numbers are measured with the load circuit of Figure 1 and defined as the time required for the output to cross the V

5

This specification only comes into play if CS goes low while SCLK is low. It is required primarily for interfacing to DSP machines.

6

These numbers are derived from the measured time taken by the data output to change 0.5 V when loaded with the circuit of Figure 1. The measured number is then extrapo­lated back to remove effects of charging or discharging the 50 pF capacitor. This means that the times quoted in the timing characteristics are the true bus relinquish times of the
part and as such are independent of external bus loading capacitances.

7

RDY returns high after a read of both ADCs. The same data can be read again, if required, while RDY is high, although care should be taken that subsequent reads do not occur
close to the next output update.

0 ns min CS Falling Edge to SCLK Active Edge Setup Time
30 ns min Data Valid to SCLK Edge Setup Time
25 ns min Data Valid to SCLK Edge Hold Time
100 ns min SCLK High Pulsewidth
100 ns min SCLK Low Pulsewidth
0 ns min CS Rising Edge to SCLK Edge Hold Time

= 2.7 V to 3.6 V

DD

or VOH limits.

OL

3

3

3, 7

3

I

(1.6mA WITH DVDD = 5V

TO OUTPUT

PIN

50pF

SINK

100A WITH DV

I

(200A WITH DVDD = 5V

SOURCE

100A WITH DV

1.6V

DD

= 3V)

DD

= 3V)

Figure 1. Load Circuit for Timing Characterization

CAUTION

ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the AD7719 features proprietary ESD protection circuitry, permanent damage may occur on
devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.

REV. 0

–7–

AD7719

DIGITAL INTERFACE

As previously outlined, the AD7719’s programmable functions
are controlled using a set of on-chip registers. Data is written to
these registers via the part’s serial interface and read access to
the on-chip registers is also provided by this interface. All com­munications to the part must start with a write operation to the
Communications Register. After power-on or

RESET

, the device
expects a write to its Communications Register. The data writ­ten to this register determines whether the next operation to the
part is a read or a write operation and also determines to which
register this read or write operation occurs. Therefore, write
access to any of the other registers on the part starts with a write
operation to the Communications Register followed by a write
to the selected register. A read operation from any other register
on the part (including the output data register) starts with a
write operation to the Communications Register followed by a
read operation from the selected register.

The AD7719’s serial interface consists of five signals, CS, SCLK,
DIN, DOUT, and RDY. The DIN line is used for transferring
data into the on-chip registers while the DOUT line is used for
accessing data from the on-chip registers. SCLK is the serial
clock input for the device and all data transfers (either on DIN
or DOUT) take place with respect to this SCLK signal. The
RDY line is used as a status signal to indicate when data is ready
to be read from the AD7719’s data register. RDY goes low when a
new data word is available in the output register of either the
main or Aux ADCs. It is reset high when a read operation from
the data register is complete. It also goes high prior to the updating
of the output register to indicate when not to read from the device

to ensure that a data read is not attempted while the register is
being updated. CS is used to select the device. It can be used to
decode the AD7719 in systems where a number of parts are
connected to the serial bus.

Figures 2 and 3 show timing diagrams for interfacing to the
AD7719 with CS used to decode the part. Figure 3 is for a read
operation from the AD7719’s output shift register while Figure 2
shows a write operation to the input shift register. It is possible
to read the same data twice from the output register even though
the RDY line returns high after the first read operation. Care must
be taken, however, to ensure that the read operations have been
completed before the next output update is about to take place.

The AD7719 serial interface can operate in 3-wire mode by
tying the CS input low. In this case, the SCLK, DIN, and
DOUT lines are used to communicate with the AD7719 and
the status of RDY bits (RDY0 and RDY1) can be obtained by
interrogating the STATUS Register. This scheme is suitable
for interfacing to microcontrollers. If CS is required as a decod­ing signal, it can be generated from a port bit. For microcontroller
interfaces, it is recommended that the SCLK idles high between
data transfers.

The AD7719 can also be operated with CS used as a frame
synchronization signal. This scheme is suitable for DSP inter­faces. In this case, the first bit (MSB) is effectively clocked out
by CS since CS would normally occur after the falling edge of
SCLK in DSPs. The SCLK can continue to run between data
transfers provided the timing numbers are obeyed.

SCLK

RDY

SCLK

DOUT

CS

CS

DIN

t

11

t

12

t

13

MSB

t

14

t

15

LSB

t

16

Figure 2. Write Cycle Timing Diagram

t

3

t

4

t

5

t

5A

MSB

t

6

t

7

t

6

t

LSB

10

t

8

t

9

Figure 3. Read Cycle Timing Diagram

–8–

REV. 0

AD7719

The serial interface can be reset by exercising the RESET input
on the part. It can also be reset by writing a series of 1s on the
DIN input. If a Logic 1 is written to the AD7719 DIN line for
at least 32 serial clock cycles the serial interface is reset. This
ensures that in 3-wire systems, if the interface gets lost either via
a software error or by some glitch in the system, it can be reset
back to a known state. This state returns the interface to where
the AD7719 is expecting a write operation to its Communica­tions Register. This operation resets the contents of all registers to
their power-on reset values.

PIN CONFIGURATION

1

IOUT1

2

IOUT2

3

AV

DD

4

AGND

AIN1

AIN2

AIN3

AIN4

AIN5

AIN6

REFIN2

10

12

13

14

P4

5

AD7719

6

TOP VIEW

(Not to Scale)

7

8

9

11

REFIN1(–)

REFIN1(+)

Some microprocessor or microcontroller serial interfaces have a
single serial data line. In this case, it is possible to connect the
AD7719’s DATA OUT and DATA IN lines together and connect
them to the single data line of the processor. A 10 kΩ pull-up
resistor should be used on this single data line. In this case, if
the interface gets lost, because the read and write operations
share the same line the procedure to reset it back to a known
state is somewhat different than previously described. It requires
a read operation of 24 serial clocks followed by a write operation
where a Logic 1 is written for at least 32 serial clock cycles to
ensure that the serial interface is back into a known state.

XTAL1

28

XTAL2

27

DV

26

DD

DGND

25

DIN

24

DOUT

23

22

RDY

21

CS

SCLK

20

19

RESET

P1/SW1

18

PWRGND

17

16

P2/SW2

P3

15

PIN FUNCTION DESCRIPTIONS

Pin No. Mnemonic Function

1 IOUT1 Output for Internal 200 µA Excitation Current Source. Either current source IEXC1 or IEXC2 or

both can be switched to this output.

2 IOUT2 Output for Internal 200 µA Excitation Current Source. Either IEXC1 or IEXC2 current source or

both can be switched to this output.

3AV

DD

Analog Supply Voltage.
4 AGND Analog Ground.
5 REFIN1(–) Negative Reference Input for Main ADC Channel. This reference input can lie anywhere between

AGND and AV
6 REFIN1(+) Positive Reference Input for Main ADC Channel. REFIN1(+) can lie anywhere between AV

DD

– 1 V.

DD

and
AGND + 1 V. The nominal reference voltage (REFIN1(+) – REFIN1(–)) is 2.5 V, but the part is
functional with a reference range from 1 V to AV

DD

.
7 AIN1 Analog Input. AIN1 is dedicated to the main channel.
8 AIN2 Analog Input. AIN2 is dedicated to the main channel.
9 AIN3 Analog Input. AIN3 can be multiplexed to either the main or auxiliary channel
10 AIN4 Analog Input. AIN4 can be multiplexed to either the main or auxiliary channel.
11 AIN5 Analog Input. AIN5 is dedicated to the auxiliary channel and is referenced to AIN6 or AGND
12 AIN6 Analog Input. AIN6 is dedicated to the auxiliary channel. It forms a differential input pair with AIN5

in fully differential input mode or is referenced to AGND in pseudo-differential mode.

13 REFIN2 Single-Ended Reference Input for Auxiliary Channel. The nominal input reference is 2.5 V. The

auxiliary channel will function with an input reference range from 1 V to AV

14 P4 General-Purpose I/O Bit. The input and output voltage levels are referenced to AV

DD

.

DD

and AGND.

15 P3 General-Purpose I/O Bit. The input and output voltage levels are referenced to AVDD and AGND.

REV. 0

–9–

AD7719

PIN FUNCTION DESCRIPTIONS (continued)

Pin No. Mnemonic Function

16 P2/SW2 Dual-Purpose Pin. It can act as a general purpose output (P2) bit referenced between AV

AGND or as a low-side power switch (SW2) to PWRGND.
17 PWRGND Ground Point for the Low-Side Power Switches SW2 and SW1. PWRGND must be tied to AGND.
18 P1/SW1 Dual-Purpose Pin. It can act as a general-purpose output (P1) bit referenced between AV

AGND or as a low-side power switch (SW1) to PWRGND.
19 RESET Digital Input Used to Reset the ADC to Its Power-On-Reset Status. This pin has a weak pull-up

internally to DV

DD

.

20 SCLK Serial Clock Input for Data Transfers to and from the ADC. The SCLK has a Schmitt triggered

input making the interface suitable for opto-isolated applications. The serial clock can be continuous

with all data transmitted in a continuous train of pulses. Alternatively, it can be a noncontinuous

clock with the information being transmitted to or from the AD7719 in smaller batches of data. A

weak pull-up to DV

is provided on the SCLK input.

DD

21 CS Chip Select Input. This is an active low logic input used to select the AD7719. CS can be used to

select the AD7719 in systems with more than one device on the serial bus or as a frame synchroniza-

tion signal in communicating with the device. CS can be hardwired low allowing the AD7719 to be

operated in 3-wire mode with SCLK, DIN and DOUT used to interface with the device. A weak

pull-up to DV

is provided on the CS input.

DD

22 RDY RDY is a Logic Low Status Output from the AD7719. RDY is low if either the Main ADC or auxil-

iary ADC channel has valid data in their data register. This output returns high on completion of a

read operation from the data register. If data is not read, RDY will return high prior to the next up-

date indicating to the user that a read operation should not be initiated. The RDY pin also returns

low following the completion of a calibration cycle. The RDY pin is effectively the digital NOR func-

tion of the RDY0 and RDY1 bits in the Status register. If one of the ADCs is disabled the RDY pin

reflects the active ADC. RDY does not return high after a calibration until the mode bits are written

to enabling a new conversion or calibration. Since the RDY pin provides information on both the

main and aux ADCs, therefore, when either the main or aux ADC is disabled it is recommended to

immediately read its data register to ensure that its RDY bit goes inactive and releases the RDY pin

to indicate output data updates on the remaining active ADC.
23 DOUT Serial Data Output Accessing the Output Shift Register of the AD7719. The output shift register can

contain data from any of the on-chip data, calibration or control registers.
24 DIN Serial Data Input Accessing the Input Shift Register on the AD7719. Data in this shift register is

transferred to the calibration or control registers within the ADC depending on the selection bits of

the Communications register. A weak pull-up to DV

is provided on the DIN input.

DD

25 DGND Ground Reference Point for the Digital Circuitry.
26 DV

DD

Digital Supply Voltage, 3 V or 5 V Nominal.
27 XTAL2 Output from the 32 kHz Crystal Oscillator Inverter.
28 XTAL1 Input to the 32 kHz Crystal Oscillator Inverter.

DD

DD

and

and

–10–

REV. 0

Typical Performance Characteristics–

AD7719

8389600

8389400

8389200

8389000

8388800

8388600

CODE READ

8388400

8388200

8388000

0 1000100

200 300

= DVDD = 5V

AV

DD

INPUT RANGE = 20mV
REFIN1(+)–REFIN1(–)=2.5V
UPDATE RATE=19.79Hz

400 500 600 700 800 900
READING NO.

MAIN ADC IN BUFFERED MODE
RMS NOISE = 0.58Vrms

= 25C

T

A

V

= 2.5V

REF

TPC 1. Typical Noise Plot on ±20 mV Input Range with

19.79 Hz Update Rate

9

8

7

6

5

4

3

2

1

0

8388841

8388382

8388039

8388499

8388449

8388579

8388547

8388615

8388657

8388687

8388721

8388754

8388805

8388779

8388906

8388874

8388985

8388941

8389033

8389110

26

24

22

20

NO MISSING CODES – Min

18

16

040302010 50 10090807060

UPDATE RATE – Hz

TPC 4. No-Missing-Codes Performance

1400

THE AMBIENT
TEMPERATURE VARIES

1200

FROM 25C TO 30C
WHILE RECORDING
THE DATA FROM

1000

THE DEVICES.

800

HITS

600

400

200

0

TEMPERATURE SENSOR – C

110

503010 20 40

REV. 0

TPC 2. Noise Distribution Histogram

3.0

= 2.5V

= 25C

2.56V RANGE

V

REF

20mV RANGE

– Volts

2.5

2.0

AVDD = DVDD = 5V
V

REF

1.5

INPUT RANGE = 2.56V
UPDATE RATE = 19.79Hz
T

A

RMS NOISE –V

1.0

0.5

0

1.0 3.02.52.01.5 3.5 5.04.54.0

TPC 3. RMS Noise vs. Reference Input

–11–

TPC 5. Temperature Sensor Accuracy

1200

1000

800

600

HITS

400

200

0

–30

MAIN CAL ACC. @ 4V – V

TPC 6. Full-Scale Error Distribution

200–20 –10 10

AD7719

AVDD = DVDD = 5V

= 25C

T

A

V

DD

OSCILLATOR

TIME BASE = 100ms/DIV
TRACE 1 = TRACE 2 = 2V/DIV

TPC 7. Typical Oscillator Power-Up

DUAL-CHANNEL ADC CIRCUIT INFORMATION

Overview

The AD7719 incorporates two independent Σ-∆ ADC channels
(main and auxiliary) with on-chip digital filtering intended for
the measurement of wide dynamic range, low frequency signals
such as those in weigh-scale, strain-gauge, pressure transducer,
or temperature measurement applications.

Main Channel

This channel is intended to convert the primary sensor input.
This channel can be operated in buffered or unbuffered mode
and can be programmed to have one of eight input voltage ranges
from ±20 mV to ± 2.56 V. This channel can be configured as
either two fully differential inputs (AIN1/AIN2 and AIN3/AIN4)
or three pseudo-differential input channels (AIN1/AIN4, AIN2/
AIN4, and AIN3/AIN4). Buffering the input channel means that
the part can accommodate significant source impedances on the
analog input and that R, C filtering (for noise rejection or RFI
reduction) can be placed on the analog inputs if required. Oper­ating in unbuffered mode leads to lower power consumption in
low power applications, but care must be exercised in unbuffered
mode as source impedances can introduce gain errors. The main
ADC also features sensor burnout currents that can be switched
on and off. These currents can be used to check that a transducer
is still operational before attempting to take measurements.

The ADC employs a sigma-delta conversion technique to realize
up to 24 bits of no-missing-codes performance. The sigma-delta
modulator converts the sampled input signal into a digital pulse

train whose duty cycle contains the digital information. A Sinc

3

programmable low-pass filter is then employed to decimate the
modulator output data stream to give a valid data conversion
result at programmable output rates from 5.35 Hz (186.77 ms)
to 105.0 3 Hz (9.52 ms). A chopping scheme is also employed
to minimize ADC channel offset errors. A block diagram of the
Main ADC input channel is shown in Figure 4. The sampling
frequency of the modulator loop is many times higher than the
bandwidth of the input signal. The integrator in the modulator
shapes the quantization noise (which results from the analog-to­digital conversion) so that the noise is pushed toward one-half of
the modulator frequency. The output of the sigma-delta modu­lator feeds directly into the digital filter. The digital filter then
band-limits the response to a frequency significantly lower than
one-half of the modulator frequency. In this manner, the 1-bit
output of the comparator is translated into a bandlimited, low
noise output from the AD7719 ADC. The AD7719 filter is a
low-pass, Sinc

3

or (SIN(x)/x)3 filter whose primary function is to
remove the quantization noise introduced at the modulator. The
cutoff frequency and decimated output data rate of the filter are
programmable via the SF word loaded to the filter register.

A chopping scheme is employed where the complete signal chain is
chopped, resulting in excellent dc offset and offset drift specifi­cations, and is extremely beneficial in applications where drift, noise
rejection, and optimum EMI rejection are important factors.
With chopping the ADC repeatedly reverses its inputs. The
decimated digital output words from the Sinc

3

filters therefore
have a positive offset and negative offset term included. As a result,
a final summing stage is included so that each output word from
the filter is summed and averaged with the previous filter output
to produce a new valid output result to be written to the ADC
data register.

Auxiliary Channel

The Auxiliary (Aux) channel is intended to convert supplemen­tary inputs such as from a cold junction diode or thermistor.
This channel is unbuffered and has an input range of ±REFIN2
or ±REFIN2/2 determined by the ARN bit in the auxiliary ADC
control register (AD1CON). AIN3 and AIN4 can be multiplexed
into the auxiliary channel as single ended inputs with respect to
AGND while AIN5 and AIN6 can operate as a differential input
pair or with AIN6 tied to AGND, AIN5 can be operated as an
additional single-ended input. A block diagram of the Auxiliary
ADC channel is shown in Figure 5.

ANALOG

INPUT

f

CHOP

MUX

BUF

f

IN

PGA

f

MOD

S-D

MOD0

f

CHOP

XOR

(

8  SF

1

3



)

SINC3 FILTER

Figure 4. Main ADC Channel Block Diagram

–12–

3 

(8  SF )

f

ADC

AIN + V
A

– V

IN

1



2

OS

OS

DIGITAL
OUTPUT

REV. 0