American Standard Dazzle 6028.240 User Manual
Installation
DAZZLE
Mini Spread Lavatory Faucet with
Speed Connect Drain*
Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only on
American Standard faucets.
Speed Connect Drain*
• 1/3 of the parts, installs in 1/3 of the time
• No tools needed
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
*Your new American Standard faucet is designed to work only with the Speed Connect drain. Helpful tips for
removing your current drain can be found in the Troubleshooting section of these instructions.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Recommended tools
Instructions
6028.240
Certified to comply with ANSI A112.18.1
M968491 Rev. 1.2
INSTALL FAUCET
1
Insert SPOUT (1) through center hole of mounting surface, making sure the
SPOUT ESCUTCHEON (2) and SEAL WASHER (3) are properly seated.
Assemble RUBBER WASHER (4), BRASS WASHER (5) and LOCKNUT (6)
onto SPOUT SHANK (7) from under side of sink . Make sure SPOUT (1)
is centered in the sink hole, the slot in the BRASS WASHER (5) is in
back and the O-RING (8) is seated at the end of SHANK (7).
Tighten LOCKNUT (6) on SPOUT (1) firmly. Fig. A.
1a
INSTALL VALVE BODY
Install the valve LOCKNUT (1), FRICTION WASHER (2) and RUBBER
WASHER (3) onto the two VALVE SHANKS (4) if not already installed.
The LABEL indicating the front of the fitting faces the front of the sink.
Insert VALVE BODY (5) through holes from under side of SINK. Threads
of both VALVE SHANKS (4) should extent at least 5/16 inch above SINK
top. Fig. B. Be sure SHANK (9) and O-RING (6) of SPOUT (7) is pushed
into TEE (8) section of the VALVE BODY (5). Fig. C.
Install ESCUTCHEONS (10) with RUBBER RINGS (11) and screw
ESCUTCHEONS (10) onto VALVE SHANKS (4) until snug against
internal stop. Adjust LOCKNUTS (1) downward if necessary.
Tighten LOCKNUTS (1) on VALVE SHANKS (4) firmly to secure fitting.
CAUTION
Turn off hot and cold water
supplies before beginning.
Adjustable Wrench Screwdriver Channel Locks
SINK OR
MOUNTING
SURFACE
Fig. C.
10
11
Fig. A.
1
2
3
SLOT
12
Tubing Cutter
7
8
4
5
6
7
9
Drop LIFT ROD (12) through hole in SPOUT (7) and thread ROD
END (13) into the TAB (14) in the VALVE BODY (5). Fig. C.
10
11
SINK
WRENCH
Fig. B.
5/16'' MIN.
SINK
4
3
2
13
14
8
T
N
RO
F
FRONT
1
1
6
5
POP-UP
CABLE
POP-UP DRAIN
2
Fig. A.
Fig. B.
Remove CLEAR PLASTIC COVER (1).
Remove CARDBOARD SPACER (2) from under
DRAIN POP-UP (3).
Tighten TAILPIECE (4) on DRAIN BODY before
installing DRAIN BODY.
REMOVE FLANGE
3
Thread FLANGE (1) counter-clockwise and remove
FLANGE (1) and FOAM GASKET (2) from drain
body.
Fig. A.
Thread LOCKNUT (3) clock-wise to bottom of
drain body. Push GASKET (4) down against
LOCKNUT (3).
Fig. B.
Fig. B.
1
3
2
Fig. A. Fig. B.
1
2
4
3
DRAIN
BODY
4
INSTALL DRAIN FROM
4
BELOW FIXTURE
From under side of SINK
install DRAIN BODY (1) up
through drain outlet.
Note: No plumber’s putty
or caulk is required.
The CABLE ATTACHMENT
POINT (2) must face towards
the rear of the SINK.
Install FOAM GASKET (3) and
FLANGE (4) onto drain body
from above SINK and tighten
FLANGE (4) firmly.
FLANGE GASKET AND POP-UP KNOB
6
Check DRAIN FLANGE in SINK to ensure that
WHITE FOAM GASKET (3) is fully compressed
and not visible. Fig. A.
POP-UP KNOB (1) must be fully down. Fig. B.
4
3
REAR OF SINK
DRAIN
OUTLET
1
2
Fig. A.
WHITE FOAM
GASKET
NOT VISIBLE
TIGHTEN LOCKNUT
5
Tighten LOCKNUT (1) firmly with Adjustable
Wrench or Channel Locks.
DOWN
DRAIN
FLANGE
Fig. B.
1
1
M968491 Rev. 1.2
2
Loading...