American Standard 3351.101, 3352.101, 3353.101, 3354.101, 2257.101 Installation Manual

INSTALLATION INSTRUCTIONS

AFWALL® MILLENNIUM™ FLUSHOMETER

WALL-MOUNTED TOILETS

Models 3351.101, 3352.101, 3353.101, 3354.101, 2257.101, 2257.101.NAF, 2633.101, 2634.101

Meets the American Disabilities Act Guidelines and ANSI A117.1

Requirements for the Physically Challenged

Thank you for selecting American Standard – the benchmark of fine quality for over 100 years.To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.

! CAUTION: PRODUCT IS FRAGILE. TWO PEOPLE ARE RECOMMENDED FOR HANDLING

TO AVOID BREAKAGE AND POSSIBLE INJURY!

NOTE: For proper operation product requires a minimum of 30 psi working line pressure

RECOMMENDED TOOLS AND MATERIALS

Closet Carrier Support	Regular Screwdriver	Sealant	Carpenters Level
Putty Knife	Adjustable Wrench	Tape Measure	Flush Valve

U S E

1 Pictures may not exactly define contour of china

73mm (2-7/8")	FINISHED WALL
		660mm
		(26")
			356mm
		470mm
			(14")
		(18-1/2")		(4) Ø 22mm
				(7/8") HOLES
			229mm	191mm
		381mm	(9")
				(7-1/2")
		(15")
		333mm
		(13-1/8")		133mm
				(5-1/4")
	41mm	FINISHED
	(1-5/8")	FLOOR

2FIXTURE MOUNTING

Fixture studs should project 58mm (2-1/4") from face of finished wall.

FINISHED WALL

58mm (2-1/4")

(4) STUDS

SIDE VIEW

FRONT VIEW

NOTE: If carrier bolt does not extend or is flush with china, use retrofit caps 7381285-200.0070A

(sold separately).

STANDARD BOLT CAP

WALL

STANDARD

BOLT CAP

CHINA / TOILET

RETROFIT BOLT CAP

WALL

RETROFIT

BOLT CAP

CHINA / TOILET

P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A S A m e r i c a , I n c .	7301962-100 Rev. E
© A S A m e r i c a , I n c . 2 01 4

S A V E F O R F U T U R E

3				Place back-up nuts on both bottom bolts, and	4			Using a level, adjust the top left back-up nut so
				the top left-hand bolt only.				that it is in the same vertical plane as the lower
				Adjust the two lower back-up nuts so that front				left back-up nut.
				face of nuts and washers are positioned to allow
				a minimum 1/16" (2mm) gap between fixture and
				wall surface.

Adjust waste horn to project 7mm (5/16") from
finished wall.	FINISHED WALL
	FINISHED WALL
	2mm (1/16")
	(IRREGULAR
	WALL SURFACE)
CLOSET	(3) NUTS
CARRIER	LEVEL
SYSTEM
	WASTE HORN
	7mm (5/16" )

5

NOTE: Bearing nuts and washers must be set to take full loading from the fixture allowing 1/16" (2mm) clearance between fixture and wall.

Follow support manufacturer's recommended setting of closet outlet connection.

Place felt or neoprene gasket (wax ring not recommended) on closet outlet.

When the fixture is installed, closet outlet gasket must be compressed sufficiently to assure a gas and watertight seal.

The following steps require a helper:

Install bowl on support using cap nuts and fiber washers with the back-up nuts and washers.

DO NOT APPLY TOP RIGHT FIBER WASHER AND CAP NUT UNTIL OTHER CAP NUTS HAVE BEEN FIRMLY TIGHTENED USING A WRENCH.

Install top right cap nut with fiber washer and run up hand tight. Wrench tighten approximately 1/4 turn.

Apply sealant to gap between bowl and finished wall. Remove excess sealant.

In the United States:

American Standard Brands

P.O. Box 6820

Piscataway, New Jersey 08855

Attention: Director of Customer Care

For residents of the United States, warranty information may also be obtained by calling the following toll free number: [phone]

www.americanstandard.com

	In Canada:	In Mexico:
	AS Canada, ULC	American Standard B&K Mexico
	5900 Avebury Rd.	S. de R.L. de C.V.
	Mississauga, Ontario	Via Morelos #330
	Canada L5R 3M3	Col. Santa Clara
	Toll Free: [phone]	Ecatepec 55540 Edo. Mexico
		Toll Free: 01-800-839-1200
	www.americanstandard.ca
		www.americanstandard.com.mx

- 2 -

7301962-100 Rev. E