INSTALLATION INSTRUCTIONS
AFWALL® MILLENNIUM™ FLUSHOMETER
WALL-MOUNTED TOILETS
Models 3351.101, 3352.101, 3353.101, 3354.101, 2257.101, 2257.101.NAF, 2633.101, 2634.101
Meets the American Disabilities Act Guidelines and ANSI A117.1
Requirements for the Physically Challenged
Thank you for selecting American Standard – the benchmark of fine quality for over 100 years.To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.
! CAUTION: PRODUCT IS FRAGILE. TWO PEOPLE ARE RECOMMENDED FOR HANDLING
TO AVOID BREAKAGE AND POSSIBLE INJURY!
NOTE: For proper operation product requires a minimum of 30 psi working line pressure
RECOMMENDED TOOLS AND MATERIALS
Closet Carrier Support |
Regular Screwdriver |
Sealant |
Carpenters Level |
Putty Knife |
Adjustable Wrench |
Tape Measure |
Flush Valve |
U S E
1 Pictures may not exactly define contour of china
73mm (2-7/8") |
FINISHED WALL |
|
|
|
|
660mm |
|
|
|
|
(26") |
|
|
|
|
|
356mm |
|
|
|
|
470mm |
|
|
|
|
(14") |
|
|
|
|
(18-1/2") |
|
(4) Ø 22mm |
|
|
|
|
|
|
|
|
|
(7/8") HOLES |
|
|
|
229mm |
191mm |
|
|
381mm |
(9") |
|
|
|
(7-1/2") |
||
|
|
(15") |
|
|
|
|
|
|
|
|
|
333mm |
|
|
|
|
(13-1/8") |
|
133mm |
|
|
|
|
|
|
|
|
|
(5-1/4") |
|
41mm |
FINISHED |
|
|
|
(1-5/8") |
FLOOR |
|
|
2FIXTURE MOUNTING
Fixture studs should project 58mm (2-1/4") from face of finished wall.
FINISHED WALL
58mm (2-1/4")
(4) STUDS
SIDE VIEW |
FRONT VIEW |
NOTE: If carrier bolt does not extend or is flush with china, use retrofit caps 7381285-200.0070A
(sold separately).
STANDARD BOLT CAP
WALL
STANDARD
BOLT CAP
CHINA / TOILET
RETROFIT BOLT CAP
WALL
RETROFIT
BOLT CAP
CHINA / TOILET
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A S A m e r i c a , I n c . |
7301962-100 Rev. E |
© A S A m e r i c a , I n c . 2 01 4 |
S A V E F O R F U T U R E
3 |
|
|
|
Place back-up nuts on both bottom bolts, and |
4 |
|
|
Using a level, adjust the top left back-up nut so |
|
|
|
|
|
||||
|
|
|
|
|
||||
|
|
|
|
the top left-hand bolt only. |
|
|
|
that it is in the same vertical plane as the lower |
|
|
|
|
Adjust the two lower back-up nuts so that front |
|
|
|
left back-up nut. |
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
face of nuts and washers are positioned to allow |
|
|
|
|
|
|
|
|
a minimum 1/16" (2mm) gap between fixture and |
|
|
|
|
|
|
|
|
wall surface. |
|
|
|
|
Adjust waste horn to project 7mm (5/16") from |
|
finished wall. |
FINISHED WALL |
|
|
|
FINISHED WALL |
|
2mm (1/16") |
|
(IRREGULAR |
|
WALL SURFACE) |
CLOSET |
(3) NUTS |
CARRIER |
LEVEL |
SYSTEM |
|
|
WASTE HORN |
|
7mm (5/16" ) |
5
NOTE: Bearing nuts and washers must be set to take full loading from the fixture allowing 1/16" (2mm) clearance between fixture and wall.
Follow support manufacturer's recommended setting of closet outlet connection.
Place felt or neoprene gasket (wax ring not recommended) on closet outlet.
When the fixture is installed, closet outlet gasket must be compressed sufficiently to assure a gas and watertight seal.
The following steps require a helper:
Install bowl on support using cap nuts and fiber washers with the back-up nuts and washers.
DO NOT APPLY TOP RIGHT FIBER WASHER AND CAP NUT UNTIL OTHER CAP NUTS HAVE BEEN FIRMLY TIGHTENED USING A WRENCH.
Install top right cap nut with fiber washer and run up hand tight. Wrench tighten approximately 1/4 turn.
Apply sealant to gap between bowl and finished wall. Remove excess sealant.
In the United States:
American Standard Brands
P.O. Box 6820
Piscataway, New Jersey 08855
Attention: Director of Customer Care
For residents of the United States, warranty information may also be obtained by calling the following toll free number: (800) 442-1902
www.americanstandard.com
In Canada: |
In Mexico: |
|
AS Canada, ULC |
American Standard B&K Mexico |
|
5900 Avebury Rd. |
S. de R.L. de C.V. |
|
Mississauga, Ontario |
Via Morelos #330 |
|
Canada L5R 3M3 |
Col. Santa Clara |
|
Toll Free: (800) 387-0369 |
Ecatepec 55540 Edo. Mexico |
|
Toll Free: 01-800-839-1200 |
||
www.americanstandard.ca |
||
www.americanstandard.com.mx |
||
|
- 2 - |
7301962-100 Rev. E |