Allied Telesis AT-PWR3201 User Manual

The RPS LED on the front of the AT-9400 Series switch
should be green. For more information about the RPS LED,
refer to the AT-9400 Series Switches Installation Guide.

The RPS LED on the front of the AT-9400 Series switch
should be green. For more information about the RPS LED,
refer to the AT-9400 Series Switches Installation Guide.

Specifications

Item Specification

Dimensions (H x W x D)

41.1 x 109 x 248.7 mm
(1.62 x 4.29 x 9.79 in.)

Operating Temperature 0° C to 40° C

Storage Temperature -20° C to 80° C

Relative Humidity <85% noncondensing

Supply Voltage 12 V

Electrical Safety and Emission Statement

This product meets the following standards.

U.S. Federal Communications Commission

Radiated Energy
Note: This equipment has been tested and found to comply with the
limits for a Class A digital device pursuant to Part 15 of FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with this instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
Note: Modifications or changes not expressly approved of by the
manufacturer or the FCC, can void your right to operate this
equipment.

Industry Canada

This Class A digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences
du Règlement sur le matériel brouilleur du Canada.

RFI Emissions EN 55022 Class A

Warn ing

In a domestic environment this product may cause
radio interference in which case the user may be
required to take adequate measures.

Immunity EN 55024

Electrical Safety UL 60950 (

Copyright © 2004 Allied Telesyn, Inc. All rights reserved. No part of
this publication may be reproduced without prior written permission
from Allied Telesyn, Inc. www.alliedtelesyn.com

), EN 60950 (TUV)

CULUS

AT-PWR3201 Power Supply

Installation Guide

Overview

The AT-PWR3201 Power Supply is designed to be installed
in an AT-RPS3204 Redundant Power Supply (RPS). The
RPS can supply power to an AT-9400 Series switch if the
switch’s main power supply fails.

STATUS

AT

-P

W

12VDC

R

3201

,10A MAX

POWER

FAULT

404

Related Documents

For details on the features and functions of your AT-9400
Series switch, refer to the following document on our web
site, www.alliedtelesyn.com:

• AT-9400 Series Switches Installation Guide
(part number 613-50569-00)

Verifying Package Contents

Verify that the correct components are included in your
package:

• AT-PWR3201 Power Supply

•One 21-pin D-combo connector cable

• This installation guide

• Warranty card

If any item is missing or damaged, contact your Allied
Telesyn sales representative for assistance.

Installing the Power Supply

To install an AT-PWR3201 Power Supply, perform the
following procedure:

1. Remove the AT-PWR3201 power supply from its
shipping package and store the package in a safe
place. You must use the original package if you need to
return the power supply to Allied Telesyn.

Specifications

Item Specification

Dimensions (H x W x D)

41.1 x 109 x 248.7 mm
(1.62 x 4.29 x 9.79 in.)

Operating Temperature 0° C to 40° C

Storage Temperature -20° C to 80° C

Relative Humidity <85% noncondensing

Supply Voltage 12 V

Electrical Safety and Emission Statement

This product meets the following standards.

U.S. Federal Communications Commission

Radiated Energy
Note: This equipment has been tested and found to comply with the
limits for a Class A digital device pursuant to Part 15 of FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with this instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
Note: Modifications or changes not expressly approved of by the
manufacturer or the FCC, can void your right to operate this
equipment.

Industry Canada

This Class A digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences
du Règlement sur le matériel brouilleur du Canada.

RFI Emissions EN 55022 Class A

Warn ing

In a domestic environment this product may cause
radio interference in which case the user may be
required to take adequate measures.

Immunity EN 55024

Electrical Safety UL 60950 (

Copyright © 2004 Allied Telesyn, Inc. All rights reserved. No part of
this publication may be reproduced without prior written permission
from Allied Telesyn, Inc. www.alliedtelesyn.com

), EN 60950 (TUV)

CULUS

AT-PWR3201 Power Supply

Installation Guide

Overview

The AT-PWR3201 Power Supply is designed to be installed
in an AT-RPS3204 Redundant Power Supply (RPS). The
RPS can supply power to an AT-9400 Series switch if the
switch’s main power supply fails.

STATUS

AT

-PW

12VDC ,10A

R3201

MAX

POWER

FAULT

404

Related Documents

For details on the features and functions of your AT-9400
Series switch, refer to the following document on our web
site, www.alliedtelesyn.com:

• AT-9400 Series Switches Installation Guide
(part number 613-50569-00)

Verifying Package Contents

Verify that the correct components are included in your
package:

• AT-PWR3201 Power Supply

• One 21-pin D-combo connector cable

• This installation guide

• Warranty card

If any item is missing or damaged, contact your Allied
Telesyn sales representative for assistance.

Installing the Power Supply

To install an AT-PWR3201 Power Supply, perform the
following procedure:

1. Remove the AT-PWR3201 power supply from its
shipping package and store the package in a safe
place. You must use the original package if you need
to return the power supply to Allied Telesyn.

PN 613-50656-00 Rev. A

PN 613-50656-00 Rev. A

2. On the back of the AT-RPS3204, locate the power

ST

S

AT

-PWR3201

STA

TU

S

PO

W

ER

FAULT

12VDC

,10A MAX

AT-PWR3201

STATUS

POW

ER

FAULT

12V

DC

,10A

M

A
X

ST

S

AT

-PWR3201

STA

TUS

PO

W

ER

FAULT

12VDC

,10A MAX

AT-PWR3201

STATUS

POW

ER

FAULT

1
2VDC

,10A

M

A
X

switch that corresponds to the slot where you are going
to install the power supply and verify that the On/Off
button is in the Off (out) position. From left to right on
the back, the power supplies are identified as B2, B1,
A2, A1. (An AT-RPS3204 is shipped with one
AT-PWR3201 in the slot marked A1.)

3. Using a Phillips head screwdriver, remove the cover
from the slot in the front of the AT-RPS3204 where you
want to install the power supply.

Note
As an example, the following steps show an
AT-PWR3201 being installed in slot A2.

ATUS

TATUS

AT-P

AT-PWR3201

W

1

12VDC ,10A MAX

2
V

R

D

320

C

1

,1

0

A

M

A

X

POWER

P

O

W

E

R

FAULT

FA

U

L

T

405

Keep the slot cover in a safe area in case you remove
a power supply. The slot cover helps maintain proper
air flow through the RPS.

4. Slide the AT-PWR3201 Power Supply into the slot.

STATUS

STATUS

AT-P

AT-PW

W

1

1

2

2V

V

R

R

D

D

3

3201

C

C

2

,1

0

1

,1

0

0

A

A

M

M

A

A

X

X

P

POWER

O

W

E

R

F

FAULT

A

U

L
T

6. On the back of the AT-RPS3204, plug one end of the
21-pin D-combo connector cable into the connector
that corresponds to the slot in which you installed the
AT-RPS3201 power supply.

ON

O

FF

A2

R

PS O

UTPU

1

2

T A2

V

D

C

AC INPUT A2/A1

1
0

0

­2

4
0

V

A
C

~

RPS OUTPUT A1

A1

1
2

V

D

ON

C

OFF

198

7. Tighten the captive screws.

ON

O

FF

A2

RPS OUTPU

1
2

T A2

V

D
C

AC

INPUT A2/A1

1
0

0

­ 2

4
0

V

A
C

~

RPS O

UTPU

A1

1
2

T A1

V

D

ON

C

O

FF

199

8. Plug the other end of the cable into the connector
labeled “RPS INPUT” on the back of the AT-9400
Series switch.

RPS INPUT

400

2. On the back of the AT-RPS3204, locate the power
switch that corresponds to the slot where you are
going to install the power supply and verify that the On/
Off button is in the Off (out) position. From left to right
on the back, the power supplies are identified as B2,
B1, A2, A1. (An AT-RPS3204 is shipped with one
AT-PWR3201 in the slot marked A1.)

3. Using a Phillips head screwdriver, remove the cover
from the slot in the front of the AT-RPS3204 where you
want to install the power supply.

Note
As an example, the following steps show an
AT-PWR3201 being installed in slot A2.

ATUS

TATUS

AT-PW

AT-PWR3201

1

12VDC ,10A MAX

2
V

R

D

3201

C

,1

0

A

M

A

X

POWER

P

O

W

E

R

FAULT

F

A

U

LT

405

Keep the slot cover in a safe area in case you remove
a power supply. The slot cover helps maintain proper
air flow through the RPS.

4. Slide the AT-PWR3201 Power Supply into the slot.

STATUS

STATUS

AT-

AT-P

P

W

W

1

12

2

V

R

V

R3201

D

D

3

C

C

2

,1

0

1

,1

0A

0

A

M

M

A

A

X

X

P

POWER

O

W

E

R

F

FAULT

A

U

L
T

6. On the back of the AT-RPS3204, plug one end of the
21-pin D-combo connector cable into the connector
that corresponds to the slot in which you installed the
AT-RPS3201 power supply.

ON

OFF

A2

RP

S OUTPU

1
2

T A2

V

D
C

A

C

INPUT A2/A1

1
0

0

­2
4

0

V

A

C

~

RPS OUTPUT A1

A1

1
2

V

D

ON

C

O

FF

198

7. Tighten the captive screws.

ON

OFF

A2

RPS OUTPU

1
2

T A2

V

D

C

A

C INPUT A2/A1

1
0

0

­2

4
0

V
A

C

~

RPS OUTPUT A1

A1

1
2

V

D

ON

C

O

FF

199

8. Plug the other end of the cable into the connector
labeled “RPS INPUT” on the back of the AT-9400
Series switch.

RPS INPUT

400

406

5. Use a Phillips head screwdriver to tighten the captive
screws.

STATUS

STATUS

AT-P

AT-P

W

W

1

1

2

2

V

R

V

R

D

D

3

3201

C

C

2
0

1

,1

,

1
0

0

A

A

M

M

A

A

X

X

P

POWER

O

W

E

R

F

FAULT

A
U

L
T

407

9. Tighten the captive screws.

RPS INPUT

401

10. Press the On/Off switch for that power supply to move
it to the On (in) position.

ON

OFF

A2

RPS OUTPU

1
2

T A2

V

D

C

AC INPUT A2/A

1
0

0

­ 2

4
0

1

V

A
C

~

RPS OUTPUT A1

A1

1
2

V

D

O

C

N

OFF

402

406

5. Use a Phillips head screwdriver to tighten the captive
screws.

STATUS

STATUS

AT-P

AT-P

W

W

1

1

2

2

V

R

V

R

D

D

3

320

C

C

2

0

1

1

,1

,
1

0

0

A

A
M

M

A

A

X

X

P

POWER

O

W

E

R

F

FAULT

A

U

L

T

407

9. Tighten the captive screws.

RPS INPUT

401

10. Press the On/Off switch for that power supply to move
it to the On (in) position.

ON

OFF

A2

RPS OUTPU

1
2

T A2

V

D

C

AC INPUT A2/A

1
0

0

­ 2

4
0

1

V

A

C

~

RPS OUTPUT A1

A1

1
2

V

D

ON

C

OFF

402