Allied Telesis AT-PWR02, AT-FAN03, AT-FAN01, AT-PWR05 User Manual

Removable Power Supply and Fan Installation Guide

AT-PWR01 AT-PWR02 AT-PWR05 AT-FAN01 AT-FAN03

Removable Power Supply and Fan Installation Guide

AT- PWR 01 AT- PWR 02 AT- PWR 05 AT- FAN0 1 AT- FAN0 3

Download the complete document set from www.alliedtelesis.com/support/software

Removable Power Supply and Fan

Removable Power Supply and Fan Installation Guide Document Number C613-04057-00 REV L

Allied Telesis, Inc. reserves the right to change specifications and other information in this document without prior written notice. The information provided herein is subject to change without notice. In no event shall Allied Telesis, Inc. be liable for any incidental, special, indirect, or consequential damages whatsoever, including but not limited to lost profits, arising out of or related to this manual or the information contained herein, even if Allied Telesis, Inc. has been advised of, known, or should have known, the possibility of such damages.

Allied Telesis, AlliedWare, AlliedWare Plus, and SwitchBlade are trademarks or registered trademarks in the United States and elsewhere of Allied Telesis, Inc. Adobe, Acrobat, and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries. Microsoft and Visio are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Additional brands, names and products mentioned herein may be trademarks of their respective companies.

Installation Guide

Contents

About this Guide .............................................................................................................. 4

Compatible Switches ....................................................................................................... 4

Package Contents ............................................................................................................. 5

Installing a Power Supply Unit or Fan .......................................................................... 6

Connecting an AC power supply .................................................................................. 9

Connecting a DC power supply .................................................................................. 11

Checking LEDs ................................................................................................................ 13

Removing a Power Supply Unit or Fan ...................................................................... 15

Troubleshooting .............................................................................................................. 16

Obtaining Documentation and Resources ............................................................... 17

Standards .......................................................................................................................... 19

EC Declaration of Conformity .................................................................................... 20

Removable Power Supply and Fan

About this Guide

This Installation Guide describes how to install the following PSUs and fans:

■ AT-PWR01 PSU, either AC or DC power supply unit

■ AT-P W R 0 2 P S U , AC only

■ AT-P W R 0 5 P S U , AC only

■ AT-FAN01, fan-only module

■ AT-FAN03, chassis fan module

Compatible Switches

The following table shows which models of PSUs and fans are appropriate for individual switches.

Switch PWR01 PWR02 PWR05 FAN01 FAN03

AT-8948

x900-48FE

x900-48FS

AT-9924T

AT-9924SP

AT-9924Ts

x900-24XT

x900-24XT-N

x900-24XS

SwitchBlade®x908

You can download complete documentation for these switches from

www.alliedtelesis.com/support/software. For more information about the

documentation and other resources, see “Obtaining Documentation and

Resources” on page 17.

Installation Guide

Package Contents

Depending on the model, switches are shipped with a single supply unit (PSU), either AC or DC. Some models also have fan-only modules (FOM), chassis fan modules, or blanking plates.

■ The AT-8948, AT-9924Ts, x900-24XT, x900-24XT-N, and x900-24XS

switches have a PSU and a FOM installed.

■ The x900-48FE, x900-48FS, AT-9924T, and AT-9924SP switches have a PSU

and a blanking plate installed.

■ The SwitchBlade

blanking plates, but no PSUs.

The following items are included with each factory-installed PSU. Contact your authorised Allied Telesis distributor or reseller if any are damaged or missing.

■ one AC power cord (AC models)

■ one power cord retaining clip (AC models)

■ one warranty card

The following items are included with PSUs when purchased separately:

■ one AC power cord (AC models)

■ one power cord retaining clip (PWR01 and PWR02 AC models only)

■ one clip-on ferrite core (PWR05 only)

■ this Installation Guide

■ one warranty card

x908 is shipped with dual chassis fan modules and

The following items are included with fans when purchased separately:

■ this Installation Guide

■ one warranty card

Removable Power Supply and Fan

Installing a Power Supply Unit or Fan

Use these instructions to install PSUs, chassis fan modules and FOMs.

■ Do not combine PWR01 and PWR02 PSUs in the same switch.

■ Do not combine AC and DC PSUs in the same switch.

Before you begin

■ Read the safety information for the switch.

Safety information is in the x900 Series Switch and SwitchBlade Installation and Safety Guide. You can download this document from

www.alliedtelesis.com/support/software.

■ Gather necessary tools and equipment.

You will need an appropriate flat-bladed or Phillips (#1) screwdriver to tighten or loosen the captive screws.

■ Verify the package contents if you have not already done so.

See “Package Contents” on page 5. Contact your authorised Allied Telesis distributor or reseller if items are damaged or missing.

■ Remove the unit from its packing material in an anti-static environment.

Caution Follow correct anti-static procedures. Failure to do so could damage the PSU, fan, or switch. If you are unsure about correct procedures, contact your authorised Allied Telesis distributor or reseller.

x908

Caution When adding or replacing power supplies, keep your hands and fingers out of the power supply bays. After installing a PWR05 power supply, use a screwdriver to tighten the captive screw such that a screwdriver will be required to remove the PSU at a later date.

+ 14 hidden pages