Allied Telesis AT-PB1000 User Manual

Technical Specifications

Maximum Operating Temperature: 0° C to 40° C (32° F to 104° F)

Maximum Storage Temperature: -25° C to 70° C (-13° F to 158° F)

Operating Altitude: Up to 3,048 meters (10,000 feet)

Humidity: 5% to 95% (non-condensing)

EMI/RFI: FCC Class A, EN55022 Class A,

EN61000-3-2, EN61000-3-3

Safety: UL 1950 (UL/cUL), EN60950, EN60825

Immunity: EN55024 Immunity Standard

Electrical Safety and Emis sion Statement

Standards: This product meets the following standards.

U.S. Federal Communications Commission

RADIATED ENERGY
Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with this instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own
expense.
Note: Modifications or changes not expressly approved of by the manufacturer or the FCC, can void your right to operate this
equipment.

Industry Canada

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

RFI Emission EN55022 Class A, EN61000-3-2, EN61000-3-3
WARNING: In a domestic environment this product may cause radio interference in which case the user may be required to take

adequate measures.

Immunity EN55024
Electrical Safety TUV-EN60950, UL1950 (UL/cUL)
Laser EN60825

AT-PB1000 Series

Gigabit Media Converters

Quick Install Guide

For use with the PowerBlade Chassis

Overview

The AT-PB1000 Series Gigabit Media Converter is designed for the PowerBlade
Chassis. This media converter extends the distance of your network by converting
Ethernet data between multimode and single-mode fiber optic cable. The media
converters feature a 1000Base-SX port and a 1000Base-LX port. The 1000Base-SX port
has a maximum operating distance of 550 meters (1,804 feet) while the 1000Base-LX
port has a maximum operating distance of 10 kilometers (6.2 miles) up to 70 kilometers
(43.4 feet) depending on the model. Both ports feature an SC connector and operate at
1000 Mpbs in half-duplex or full-duplex mode.

Related Documents

This quick install guide is an abbreviated version of the installation procedure. For
complete details on the features, functions and installation instructions, refer to the
PowerBlade Chassis Installation Guide . This guide is available from Allied Telesyn’s
web site at www.alliedtelesyn.com.

Cable Specifications

The following table lists the cabling distances for the AT-PB1000 Series modules.

1000Base-LX 1000Base-SX

Copyright  2000 Allied Telesyn International, Corp.
All rights reserved. No part of this publication may be reproduced without prior written permission from Allied
Telesyn International, Corp.

Model

Type of
Connector

Maximum
Distance

1

AT-PB1001/1 SC 10 km (6.2 mi) SC 550 m (1,804 ft)

Type of
Connector

Maximum
Distance

2

AT-PB1001/2 SC 20 km (12.4 mi) SC 550 m (1,804 ft)
AT-PB1001/3 SC 50 km (31 mi) SC 550 m (1,804 ft)

Allied Telesyn International Corp.

960 Stewart Drive, Suite B
Sunnyvale, CA 94085 USA

Tel [phone] • Fax [phone]

Visit our web site at: www.alliedtelesyn.co

3 PN 613-50149-00 Rev A 010213

e

AT-PB1001/4 SC 70 km (43.4 mi) SC 550 m (1,804 ft)

1. Assumes 10/125 micron single-mode fiber optic cable.

2. Assumes 50/125 micron multimode fiber optic cable.

The following table lists the IEEE 802.3u cabling specifications for the AT-PB1000

Series modules when operating in full-duplex mode.

Port Cable Type Maximum Distance

Note

End stations used with the media converter must operate with the same duplex
mode (either both full-duplex or both half-duplex mode).

1000Base-SX

All Models 62.5/125

50/125

1000Base-LX

AT-PB1001/1 62.5/12 5

50/12 5

10/125
AT-PB1001/2 10/125
AT-PB1001/3 10/125
AT-PB1001/4 10/125

Cabling specifications for half-duplex operation can be found in the PowerBlade Chassis
Installation Guide.

µm multimode fiber 275 m (902 ft)

µm multimode fiber 550 m (1,804 ft)

µm multimode fiber 550 m (1,804 ft)
µm multimode fiber 550 m (1,804 ft)
µm single-mode fiber 10,000 m (32,800 ft)
µm single-mode fiber 20 km (12.4 mi)
µm single-mode fiber 50 km (31 mi)
µm single-mode fiber 70 km (43.4 mi)

Package Contents

Make sure the following items are included in your package. If any of these items are
missing or damaged, contact your Allied Telesyn sales representative.

❑ One AT-PB1000 Series Gigabit Media Converter
❑ This quick install guide
❑ Warranty card

Installing the Media Converter

1. Remove a blank faceplate from an empty expansion slot on the front of the chassis.
The module can be installed in any slot.

2. Remove the module from the shipping package and store the packaging in a safe
place. Be sure to observe standard ESD precautions.

3. Slide the module into the expansion slot, aligning it with the guiderails, until it
firmly connects to the chassis’ backplane.

4. Secure the module to the chassis by tightening the thumbscrew.

5. Verify that the PR LED on the front of the module is green.

6. Set the ML/LT switch to the LT (Link Test) position.

7. Set the LT BB/LT SA button to either back to back or standalone, depending on your
topology. Refer to the PowerBlade Chassis Installation Guide for additional
information.

8. Remove the dust covers from the fiber optic connectors and connect the data cables.

9. Power ON the end nodes.

10. Check that the LK LEDs on both ports on the media converter are green. If the
LEDs are OFF, refer to the PowerBlade Chassis Installation Guide for
troubleshooting instructions.

11. If the link test is successful, set the ML/LT switch to the ML (MissingLink) position.
The ML LED should be green. The media converter will not pass network traffic
when a link test is being performed.

12. Repeat this procedure to install additional AT-PB1000 Series modules.

Status LEDs

LED Color Description
System LEDs

PR Green Power is applied to the media converter.
ML Green

OFF

Port LEDs

LK Green A link has been established on the port.

The MissingLink fe ature is activated.
The MissingLink feature is disabled and the media converter is operating in

the link test mode.

Fiber Optic Port Specifications

Port Cable

1000Base-SX

All Models 50/125 or 62.5/125 micron

multimode

1000Base-LX

AT-PB1001 10/125 micron single-mode -9.5 to -3.0 1310 -20.0

50/125 or 62.5/125 micron

multimode
AT-PB1001/2 10/125 micron single-mode -3.0 to 0.0 1310 -24.0
AT-PB1001/3 10/125 micron single-mode -5.0 to 0.0 1550 -24.0
AT-PB1001/4 10/125 micron single-mode 0.0 to 5.0 1550 -24.0

Transmitter
Output Power
(dBm avg.)

-9.5 to -4.0 850 -17.0

-11.5 to -3.0 1310 -20.0

Wavelength
(nm)

Minimum
Receiver
Sensivity
(dBm avg.)

1 2