Suffix '–LT' & '–UA' Pinning
X |
|
|
|
|
PTCT |
VCC |
|
|
1 |
2 |
3 |
SUPPLY |
GROUND |
OUTPUT |
|
|
Dwg. PH-003-2 |
Pinning is shown viewed from branded side.
ABSOLUTE MAXIMUM RATINGS
at TA = +25°C
Supply Voltage, VCC |
........................ |
|
26.5 V |
Reverse Battery Voltage, VRCC |
.......... -30 V |
||
Magnetic Flux Density, ...........B |
|
Unlimited |
|
Output Off Voltage, V ...................OUT |
|
26 V |
|
Continuous Output Current, |
|
||
IOUT ....................... |
Internally Limited |
||
Reverse Output Current, ........IOUT |
-50 mA |
||
Package Power Dissipation, PD . See Graph |
|||
Junction Temperature, ...............TJ |
|
+170°C |
|
Operating Temperature Range, TA |
|||
Suffix ‘E–’.................. |
|
-40°C to +85°C |
|
Suffix ‘L–’................ |
|
-40°C to +150°C |
|
Storage Temperature Range, |
|
||
TS .............................. |
|
-65°C to +170°C |
3280, 3281, |
20.27609 |
SheetData |
|
AND 3283 |
|||
|
|
||
|
|
|
CHOPPER-STABILIZED, PRECISION HALL-EFFECT LATCHES
The A3280--, A3281--, and A3283-- Hall-effect latches are extremely temperature-stable and stress-resistant sensors especially suited for operation over extended temperature ranges to +150°C. Superior high-temperature performance is made possible through dynamic offset cancellation, which reduces the residual offset voltage normally caused by device overmolding, temperature dependencies, and thermal stress. The three devices are identical except for magnetic switch points.
Each device includes on a single silicon chip a voltage regulator, Hall-voltage generator, small-signal amplifier, chopper stabilization, Schmitt trigger, and a short-circuit protected open-collector output to sink up to 25 mA. A south pole of sufficient strength will turn the output on. A north pole is necessary to turn the output off. An on-board regulator permits operation with supply voltages of 4.2 to 24 volts.
The first character of the part number suffix determines the device operating temperature range; suffix ‘E–’ is for -40°C to +85°C and ‘L–’ is -40°C to +150°C. Three package styles provide a magnetically optimized package for most applications. Suffix ‘–LH’ is a miniature low-profile surface-mount package, ‘–LT’ is a miniature SOT-89/TO- 243AA transistor package for surface-mount applications; while suffix ‘–UA’ is a three-lead ultra-mini-SIP for through-hole mounting.
FEATURES
■Symmetrical Switch Points
■Resistant to Physical Stress
■Superior Temperature Stability
■Output Short-Circuit Protection
■Operation From Unregulated Supply
■Reverse Battery Protection
■Solid-State Reliability
■Small Size
Always order by complete part number: the prefix ‘A’ + the basic fourdigit part number + a suffix to indicate operating temperature range + a suffix to indicate package style, e.g., A3281ELH .
3280, 3281, AND 3283
CHOPPER-STABILIZED, PRECISION HALL-EFFECT LATCHES
|
|
|
FUNCTIONAL BLOCK DIAGRAM |
|
|||
|
|
|
SUPPLY |
|
|
|
|
|
REG. |
TO ALL |
|
|
|
|
|
|
SUBCIRCUITS |
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
OFFSET CANCELLATION |
|
|
|
|
OUTPUT |
X |
DYNAMIC |
SAMPLE & HOLD |
LOW-PASS |
FILTER |
|
|
|
|
CONTROL |
|
|||||
|
CURRENT |
|
|||||
|
LIMIT |
|
|||||
|
|
|
|||||
|
|
|
|
|
|
<1Ω |
GROUND |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Dwg. FH-020-1 |
|
700 |
|
|
|
|
|
|
|
|
in MILLIWATTS |
600 |
|
|
|
|
|
|
|
|
500 |
|
|
Suffix "–UA" |
|
|
|
|
||
DISSIPATION |
|
|
|
|
|
|
|
||
|
|
|
RθJA = 206°C/W |
|
|
|
|
||
400 |
|
Suffix "–LT" |
|
|
Suffix "–LH" |
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
RθJA = 258°C/W |
|
|
RθJA = 248°C/W |
|
|
||
POWER |
|
|
|
|
|
|
|||
300 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PACKAGE |
200 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ALLOWABLE |
100 |
|
|
|
|
|
|
|
|
|
|
Suffix "E–" |
|
|
Suffix "L–" |
|
|
||
|
|
|
|
|
|
|
|
||
0 |
|
|
|
|
|
|
|
|
|
|
40 |
|
80 |
|
120 |
|
160 |
180 |
|
|
20 |
60 |
100 |
140 |
AMBIENT TEMPERATURE in °C
Dwg. GH-046-2C
Suffix ‘–LH’ Pinning
|
3 |
X |
|
|
PTCT |
VCC |
|
1 |
2 |
SUPPLY |
GROUND |
OUTPUT |
|
|
Dwg. PH-003-4 |
2 |
115 Northeast Cutoff, Box 15036 |
Worcester, Massachusetts 01615-0036 (508) 853-5000 |
Copyright © 2000 Allegro MicroSystems, Inc.
3280, 3281, AND 3283
CHOPPER-STABILIZED, PRECISION HALL-EFFECT LATCHES
ELECTRICAL CHARACTERISTICS over operating temperature range.
|
|
|
|
Limits |
|
|
|
|
|
|
|
|
|
Characteristic |
Symbol |
Test Conditions |
Min. |
Typ. |
Max. |
Units |
|
|
|
|
|
|
|
Supply Voltage Range |
VCC |
Operating, TJ < 170°C1 |
4.2 |
– |
24 |
V |
Output Leakage Current |
IOFF |
VOUT = 24 V, B < BRP |
– |
– |
10 |
µA |
Output Saturation Voltage |
VOUT(SAT) |
IOUT = 20 mA, B > BOP |
– |
185 |
500 |
mV |
Output Current Limit |
IOM |
B > BOP |
30 |
– |
60 |
mA |
Power-On Time |
tpo |
VCC > 4.2 V |
– |
– |
50 |
µs |
Chopping Frequency |
fC |
|
– |
340 |
– |
kHz |
Output Rise Time |
tr |
RL = 820 Ω, CL = 20 pF |
– |
0.2 |
2.0 |
µs |
Output Fall Time |
tf |
RL = 820 Ω, CL = 20 pF |
– |
0.1 |
2.0 |
µs |
Supply Current |
ICC |
B < BRP, VCC = 12 V |
– |
3.0 |
8.0 |
mA |
|
|
B > BOP, VCC = 12 V |
– |
4.0 |
8.0 |
mA |
Reverse Battery Current |
ICC |
VRCC = -30 V |
– |
– |
-5.0 |
mA |
Zener Voltage |
VZ + VD |
ICC = 15 mA, TA = 25°C |
28 |
32 |
37 |
V |
Zener Impedance |
zz + zD |
ICC = 15 mA, TA = 25°C |
– |
50 |
– |
Ω |
NOTES:1. Maximum voltage must be adjusted for power dissipation and junction temperature.
2.BOP = operate point (output turns on); BRP = release point (output turns off).
3.Typical Data is at TA = +25°C and VCC = 12 V and is for design information only.
MAGNETIC CHARACTERISTICS over operating supply voltage range.
|
|
|
|
|
|
Part Numbers1 |
|
|
|
|
||
|
|
|
A3280 |
|
|
A3281 |
|
|
|
A3283 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Characteristic |
Test Conditions |
Min. |
Typ. |
Max. |
Min. |
Typ. |
Max. |
|
Min. |
Typ. |
Max. |
Units |
|
|
|
|
|
|
|
|
|
|
|
|
|
Operate Point, BOP |
at TA = +25°C and TA = max. |
5.0 |
22 |
40 |
15 |
50 |
90 |
|
100 |
150 |
180 |
G |
|
at TA = -40°C |
5.0 |
– |
40 |
15 |
– |
90 |
|
100 |
– |
200 |
G |
Release Point, BRP |
at TA = +25°C and TA = max. |
-40 |
-23 |
-5.0 |
-90 |
-50 |
-15 |
|
-180 |
-150 |
-100 |
G |
|
at TA = -40°C |
-40 |
– |
-5.0 |
-90 |
– |
-15 |
|
-200 |
– |
-100 |
G |
Hysteresis, Bhys |
at TA = +25°C and TA = max. |
10 |
45 |
80 |
30 |
100 |
180 |
|
– |
300 |
360 |
G |
(BOP - BRP) |
at TA = -40°C |
– |
– |
80 |
– |
– |
180 |
|
– |
– |
400 |
G |
|
|
NOTES:1. Complete part number includes a suffix to identify operating temperature range (E or L) and package type (LH, LT, or UA).
2.As used here, negative flux densities are defined as less than zero (algebraic convention) and -50 G is less than +10 G.
3.Typical Data is at TA = +25°C and VCC = 12 V and is for design information only.
www.allegromicro.com |
3 |
3280, 3281, AND 3283
CHOPPER-STABILIZED, PRECISION HALL-EFFECT LATCHES
TYPICAL OPERATING CHARACTERISTICS as a function of temperature
SWITCH POINTS IN GAUSS
A3280* SWITCH POINTS |
A3281* SWITCH POINTS |
50 |
|
|
|
|
|
|
|
|
|
100 |
|
|
|
|
|
|
|
|
40 |
|
|
|
|
|
|
|
|
|
80 |
|
|
|
|
|
|
|
|
30 |
|
|
|
OPERATE POINT |
|
|
|
|
60 |
|
|
|
OPERATE POINT |
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
GAUSS |
|
|
|
|
|
|
|||
20 |
|
|
|
|
|
|
|
|
40 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
10 |
|
|
|
|
|
|
|
|
IN |
20 |
|
|
|
|
|
|
|
|
|
VCC = 4.5 V |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
-10 |
|
|
|
|
|
|
POINTS |
-20 |
VCC = 4.5 V to 24 V |
|
|
|
|
|
||||
0 |
VCC = 24 V |
|
|
|
|
|
|
|
0 |
|
|
|
|
|
||||
-20 |
|
|
RELEASE POINT |
|
|
|
|
SWITCH |
-40 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
RELEASE POINT |
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
-30 |
|
|
|
|
|
|
|
|
|
-60 |
|
|
|
|
|
|
|
|
-40 |
|
|
|
|
|
|
|
|
|
-80 |
|
|
|
|
|
|
|
|
-50 |
|
|
|
|
|
|
|
|
|
-100 |
|
|
|
|
|
|
|
|
-50 |
-25 |
0 |
25 |
50 |
75 |
100 |
125 |
150 |
|
-50 |
-25 |
0 |
25 |
50 |
75 |
100 |
125 |
150 |
|
|
AMBIENT TEMPERATURE IN °C |
|
Dwg. GH-026-3 |
|
|
|
AMBIENT TEMPERATURE IN °C |
|
Dwg. GH-026-4 |
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
200 |
|
|
|
|
|
160 |
|
GAUSS |
120 |
|
40 |
|
|
|
80 |
|
IN |
-40 |
|
|
||
POINTS |
|
|
SWITCH |
0 |
|
-80 |
|
|
|
|
|
|
-120 |
|
|
-160 |
|
|
-200 |
|
|
|
|
|
-50 |
A3283* SWITCH POINTS
OPERATE POINT
VCC = 4.5 V
VCC = 24 V
RELEASE POINT
-25 |
0 |
25 |
50 |
75 |
100 |
125 |
150 |
AMBIENT TEMPERATURE IN °C
Dwg. GH-026-6
* Complete part number includes a suffix denoting operating temperature range (E or L) and package type (LH, LT, or UA).
4 |
115 Northeast Cutoff, Box 15036 |
Worcester, Massachusetts 01615-0036 (508) 853-5000 |