Page 1
HS-TX494
YU,YZ
HS-TX496
HS-TX591
HS-TX594
HS-TX596
YH,YJ,YL,YZ
YU
YZ
YH,YJ,YL,YZ
SERVICE MANUAL
STEREO RADIO CASSETTE
PLAYER
BASIC TAPE MECHANISM : 8ZM-3 P2N
8ZM-3 P3N
S/M Code No. 09-995-407-8R1
REVISION
Page 2
SPECIFICATIONS
Frequency range: AM: 530/531 1.710/1.602 kHz (10/9 kHz step)
531 1.629 kHz (9 kHz step)<EXCEPT YZ>
FM1,FM2: 87.5/87.5 108/108.1 MHz (50/200 kHz step)
76 108 MHz (100 kHz step in 76 90 MHz,
50 kHz step in 90 108 MHz)<EXCEPT YZ>
TV:<591YU ONLY>
2ch 59.75 MHz
3ch 65.75 MHz
4ch 71.75 MHz
5ch 81.85 MHz
6ch 87.85 MHz
7ch 179.75 MHz
8ch 185.75 MHz
9ch 191.75 MHz
10ch 197.75 MHz
11ch 203.75 MHz
12ch 209.75 MHz
13ch 215.75 MHz
WEATHER:<591YU ONLY>
1ch
2ch
3ch
4ch
5ch
6ch
7ch
Maximum output: 4 mW + 4 mW (EIAJ/16 ohms)<YZ ONLY>
12 mW + 12 mW (EIAJ/32 ohms)
Load impedance: 16 32 ohms<YZ ONLY>
Power source: Battery DC 3V, R6 (size AA) x 2
Domestic AC power (using optional AC adaptor: AIWA AC-D302)
Battery lift (EIAJ,
1mW output,playback): Approx.7hours using R6P (size AA) manganese batteries
Approx.24hours using LR6 (size AA) alkaline batteries
Maximum dimensions
(W x H x D): 112.8 x 88 x 32.7 mm (41/2 x 31/2 x 15/16inches)
Weight
(excluding batteries): Approx.140 g (4.9 oz)
Accessories: Stereo headphones (1)<494/496 YZ, 494 YU, 496 YL, 496 YH/YL, 591 YU>
Stereo headphones equipped with remote control (1)<594/596 YZ, 596 YL, 596 YH/YL>
Belt clip (1)
Supplied headphones: HPM007:<494/496 YZ>
HPMR105:<594/596 YZ>
Type: Inear type
Impedance: 32 ohms
Sensitivity: 105 dB/mW
Recommended
commercially
avaiable headphones: Type: Inear/Headband type/Vertical type<494/496 YZ>
Inear/Headband type/Vertical type<594/596 YZ>
Impedance: 1632 ohms
Sensitivity: 100109 dB/mW
Design and specifications are subject to change without notice.
162.550 MHz
162.440 MHz
162.475 MHz
162.425 MHz
162.450 MHz
162.500 MHz
162.525 MHz
2
Page 3
NO.
REF. NO. DESCRIPTIONPART NO. DESCRIPTIONREF. NO. KANRI
NO.
PART NO. KANRI
NO.
REF. NO. DESCRIPTIONPART NO.
3
C99 87-A10-422-080 C-CAP,TN 10-4 A TCF
C101 87-A10-047-080 CAP,U 1-10 ZF<EXCEPT 591YU>
C102 87-012-274-080 C-CAP,U 1000P-50 K B
C103 87-A10-047-080 C-CAP,U 1-10 Z F
C104 87-010-831-080 C-CAP,U,0.1-16F
C105 87-010-503-010 CAP,E 220-4 GAS
C110 87-010-853-080 C-CAP,220-4V H5.5
C201 87-A10-504-080 C-CAP,U 0.047-16 KB<591YU>
C201 87-012-286-080 CAP,U 0.01-25<EXCEPT 591YU>
C202 87-012-273-080 CAP,U 820P-50B<EXCEPT 591YU>
C202 87-012-286-080 CAP,U 0.01-25<591YU>
C203 87-012-172-080 C-CAP,U 10P CH<EXCEPT 591YU>
C204 87-012-180-080 C-CAP,U 22P-50 CH<591YU>
C205 87-012-272-080 C-CAP,U 680P-50B<591YU>
C205 87-012-272-080 CAP,U 680P-50B<EXCEPT 591YU>
C206 87-012-168-080 CAP,U 6P-50 CH<EXCEPT 591YU>
C207 87-012-286-080 CAP, U 0.01-25
C208 87-012-286-080 CAP, U 0.01-25<591YU>
C209 87-012-186-080 C-CAP,U 39P-50 CH<591YU>
C210 87-012-156-080 CAP,220P-50 CH<EXCEPT 591YU>
C210 87-012-272-080 CAP,U 680P-50 K B GRM<591YU>
C212 87-012-286-080 CAP, U 0.01-25
C213 87-012-195-080 C-CAP,U 100P-50CH<591YU>
C215 87-012-162-080 C-CAP,U 1P-50 CK<591YU>
C216 87-012-162-080 CAP,U 1P-50 CK<EXCEPT 591YU>
C216 87-012-162-080 C-CAP,U 1P-50 CK<591YU>
C217 87-A10-047-080 CAP,U 1-10 Z F<EXCEPT 591YU>
C222 87-010-831-080 C-CAP,U 0.1-16 Z F<591YU>
C222 87-010-831-080 CAP,U,0.1-16F<EXCEPT 591YU>
C224 87-012-336-080 CAP, CHIP SS 330P SL<591YU>
C224 87-012-274-080 CAP,U 1000P-50B<EXCEPT 591YU>
C225 87-A10-047-080 C-CAP,U 1-10 Z F<591YU>
C226 87-A10-047-080 C-CAP,U 1-10 Z F
C227 87-012-273-080 C-CAP,U 820P-50 B<591YU>
C228 87-012-274-080 C-CAP,U 1000P-50 K B<591YU>
C229 87-010-831-080 C-CAP,U,0.1-16F
C230 87-010-831-080 C-CAP,U,0.1-16F
C231 87-010-959-080 CHIP CAP,U 0.056-16F<591YU>
C231 87-010-959-080 CAP,U 0.056-16F<EXCEPT 591YU>
C232 87-010-959-080 CHIP CAP,U 0.056-16F
C233 87-012-287-080 CAP,U 0.015-25F<EXCEPT 591YU>
C233 87-012-275-080 C-CAP,U 1200P-50 B<591YU>
C234 87-012-287-080 CAP,U 0.015-25F<EXCEPT 591YU>
C234 87-012-275-080 C-CAP,U 1200P-50 B<591YU>
C235 87-012-286-080 C-CAP,U 0.01-25 K B<591YU>
C235 87-A10-047-080 CAP,U 1-10 Z F<EXCEPT 591YU>
C236 87-A10-420-080 C-CAP,TN 4.7-4 A TCF<591YU>
C236 87-A10-420-080 CAP,TN 4.7-4 <EXCEPT 591YU>
C237 87-A10-047-080 CAP,U 1-10 Z F<EXCEPT 591YU>
C237 87-A10-047-080 C-CAP,U 1-10 Z F<591YU>
C238 87-012-286-080 CAP, U 0.01-25<591YU>
C239 87-012-358-080 C-CAP,S 0.47-10 F Z<591YU>
C239 87-A10-707-080 CAP,U 0.47-10FZ<EXCEPT 591YU>
C240 87-010-574-080 CAP,S 470P<EXCEPT *1,494YZ>
C240 87-012-193-080 C-CAP,U 82P-50 CH<591YU>
C240 87-012-193-080 CAP,82P <496YL, 494YU,494YZ>
C241 87-012-170-080 C-CAP,U 8P-50 CH<591YU>
C241 87-012-176-080 CAP 15P<EXCEPT 591YU>
C242 87-010-574-080 CAP,S 470P-50UJ<EXCEPT 591YU>
C242 87-012-193-080 CAP,U 82P CH<EXCEPT *1,494YZ>
C242 87-012-270-080 CAP, U 470P-50<591YU>
C243 87-012-172-080 CAP,U 10P-50DCH<EXCEPT 591YU>
C243 87-012-174-080 C-CAP CERA SS 12P CHJ<591YU>
C244 87-010-831-080 CAP,U,0.1-16F<EXCEPT 591YU>
C244 87-010-787-080 CAP, U 0.022-25<591YU>
C245 87-012-275-080 C-CAP,U 1200P-50 B<591YU>
C245 87-012-272-080 CAP,U 680P GRM<496YL,494YU>
C246 87-012-271-080 C-CAP,U 560P-50 K B<591YU>
C247 87-012-286-080 CAP, U 0.01-25<591YU>
C248 87-012-274-080 C-CAP,U 1000P-50 K B<591YU>
4
C248 87-012-195-080 CAP,U 100P-50CH<EXCEPT 591YU>
C249 87-012-286-080 CAP, U 0.01-25<591YU>
C250 87-010-853-080 CAP,220-4V H5.5<EXCEPT 591YU>
C250 87-010-853-080 C-CAP,220-4V H5.5<591YU>
C251 87-012-286-080 C-CAP,U 0.01-25 K B<591YU>
C251 87-012-195-080 CAP,U 100P-50CH<EXCEPT 591YU>
C252 87-012-271-080 CAP, U 560P-50<591YU>
C253 87-012-286-080 C-CAP,U 0.01-25 K B
C259 87-012-167-080 C-CAP,U 5P-50 CH<591YU>
C290 87-010-787-080 CAP, U 0.022-25<494YZ>
C301 87-012-277-080 CAP,U 1800P<EXCEPT 591YU>
C302 87-012-277-080 C-CAP,U 1800P-50 B
C303 87-012-277-080 C-CAP,U 1800P-50 B
C304 87-012-277-080 C-CAP,U 1800P-50 B
C308 87-A10-047-080 C-CAP,U 1-10 Z F
C309 87-A10-047-080 C-CAP,U 1-10 Z F
C310 87-A10-047-080 CAP,U 1-10 Z F<EXCEPT 591YU>
C311 87-012-174-080 CAP CHIP CERA SS 12P CHJ
C312 87-012-176-080 CAP 15P
C313 87-A10-047-080 C-CAP,U 1-10 Z F
C314 87-010-831-080 C-CAP,U 0.1-16 Z F
C315 87-010-831-080 C-CAP,U 0.1-16 Z F
C317 87-A10-047-080 C-CAP,U 1-10 Z F
C318 87-016-462-080 C-CAP,S 1-16 F<EXCEPT 591YU>
C318 87-A10-047-080 C-CAP,U 1-10 Z F<591YU>
C319 87-010-787-080 CAP, U 0.022-25
C320 87-010-505-080 CA, CHIP TANTALUM 1-16
C321 87-012-286-080 CAP, U 0.01-25
C322 87-012-337-080 C-CAP,U 56P-50 CH
C323 87-012-167-080 C-CAP,U 5P-50 CH
C324 87-012-170-080 C-CAP,U 8P-50 CH
C325 87-012-188-080 CAP,U 47P-50 CH<EXCEPT 591YU>
C326 87-A10-047-080 CAP,U 1-10 Z F<EXCEPT 591YU>
C326 87-A10-047-080 C-CAP,U 1-10 Z F<591YU>
C901 87-012-274-080 CHIP CAP,U 1000P-50B
C902 87-010-831-080 CAP,U,0.1-16F<EXCEPT 591YU>
C904 87-012-274-080 CAP,U 1000P<EXCEPT 591YU>
C906 87-A10-047-080 C-CAP,U 1-10 Z F<591YU>
C907 87-012-274-080 C-CAP,U 1000P-50 K B<591YU>
C909 87-012-271-080 CAP, U 560P-50<591YU>
C914 87-012-274-080 CHIP CAP,U 1000P-50B<591YU>
C999 87-012-270-080 CAP, U 470P-50<494YZ1>
CF202 87-A91-321-080 FLTR,SFECV10.7MA5A-TC<591YU>
CF202 87-A91-343-010 FLTR,SK107M2N <EXCEPT 591YU>
CF203 87-A90-456-080 C-FLTR,PFWCC 450J3<591YU>
CF203 87-A90-710-010 AM IF PF S450A3<EXCEPT 591YU>
CF204 87-A91-313-080 FLTR,CDACV10.7 <591YU>
CF204 87-A91-313-080 FLTR,CDACV10.7<EXCEPT 591YU>
CT201 87-A91-183-080 TRIMMER,CER10P<EXCEPT 591YU>
CT202 87-A91-183-080 TRIMMER,CER 10P TZC03<591YU>
IFT201 87-005-788-080 IFT,AM 5M 5CLD<EXCEPT 591YU>
IFT201 87-005-788-080 C-IFT,AM 5M 5CLD<591YU>
J1 87-A60-438-010 JACK,SW (1537)<EXCEPT *2>
J1 87-A60-437-010 JACK,SW 4P(1637)< *2>
J101 87-A60-849-010 JACK,DC DIA 2.75 BLK
L1 87-003-231-080 C-COIL 1UH<EXCEPT 591YU>
L1 87-003-240-080 C-COIL,S 3.3UH<591YU>
L2 87-003-231-080 C-COIL 1UH<EXCEPT 591YU>
L2 87-003-240-080 C-COIL,S 3.3UH<591YU>
L3 87-003-231-080 C-COIL 1UH<EXCEPT 591YU>
L3 87-003-240-080 C-COIL,S 3.3UH<591YU>
L4 87-003-243-080 C-COIL,S 10UH<* 2>
L101 87-003-243-080 COIL,2125 10UH <EXCEPT 591YU>
L201 8Z-HRB-605-080 C-COIL,RF TV<591YU>
L202 8Z-HRB-603-080 C-COIL,RF FM<591YU>
L202 8Z-HRB-610-010 COIL,FM RF<EXCEPT 591YU>
L203 8Z-HRB-604-080 C-COIL,OSC TV<591YU>
L204 8Z-HRB-602-080 C-COIL,OSC FM<591YU>
L204 8Z-HRB-609-010 COIL,FM OSC<EXCEPT 591YU>
L205 87-005-898-080 COIL,S 2.2UH K LK2125<591YU>
L206 87-HRA-603-010 BAR-ANT,MW
L207 87-003-226-080 INDUCTOR 100UJ<EXCEPT 591YU>
L207 87-003-226-080 INDUCTOR 100UJ<591YU>
L208 87-003-231-080 C-COIL 1UH<591YU>
L301 87-A50-037-080 C-COIL,D-D 5CDLU<591YU>
L301 87-A50-230-080 COIL,D-D<EXCEPT 591YU>
L900 87-003-243-080 C-COIL,S 10UH<591YU>
LCD301 8Z-HR9-603-010 LCD,HS ASSY(BAND/TU)
R97 87-012-270-080 CAP470P<EXCEPT 591YU,494YZ>
R111 87-022-656-080 C-RES,K43G 0.68
R998 87-012-286-080 CAP, U 0.01-25<591YU>
S1 8Z-HRB-607-010 SW,SL 2-2-2 SSZZ-S-502(S)
S2 87-A90-050-010 SW, SL 2-2-2 NS (BLK)
S101 87-A91-077-010 SW,LEAF
S301 87-A91-320-080 SW,SL 1-1-2 SSSS8A2-B-2B(NC)
S302 87-A90-665-180 C-SW,TACT LS7A2M
S303 87-A90-665-180 C-SW,TACT LS7A2M
SFR101 87-024-050-010 SEMI-FIXED RESISTOR, 1K
TH101 87-A91-322-080 C-THMS,157-101-53028-TP
TH301 87-A90-547-080 C-THMS,47K (5%)NTH 5G
VR1 87-A90-818-010 VR,RTRY 20KCX2
X301 87-A70-187-010 VIB,XTAL 75KHZ CFV206
88
A
Resistor Code
Chip Resistor Part Coding
Figure
Value of resistor
Chip resistor
Wattage Type Tolerance
1/16W
1/10W
1/8W
1608
2125
3216
5%
5%
5%
CJ
CJ
CJ
Form
LW t
1.6 0.8 0.45
2 1.25 0.45
3.2
1.6
108
118
128
: A
: A
CHIP RESISTOR PART CODE
0.55
Resistor Code
Dimensions (mm)
Symbol
1/16W 1005 5% CJ
1.0 0.5 0.35 104
L
t
W
NOTE: *1:591YU,496YL,494YU
*2:596YL,594YZ,596YH,596YJ596YZ
Page 4
RN1307
RN1311
RN1310
2SA1362GR
RN2307
RN2411
RN2311
TRANSISTOR ILLUSTRATION
B
E
C
RN2305
2SC2714O
2SC4215
2SC4116GR
RN1304
RN1404
65
Page 5
H or Weather band .
1 ~ 3 COM1 ~ COM3 O LCD common output.
4 ~ 22 S1 ~ S19 O LCD segment output.
23 ~ 26 S20 ~ S23 - Not used.
27 ~ 30 K0 ~ K3 I Key matrix input.
31 ~ 34 T0 ~ T3 O Key return timing output.
35 FM/AM O H: FM,L:AM
36 MSP O The output port is used for Super-Bass On/Off.
37 MSP O Not used.
38 TV OUT O Not used .
39,40 DES I These two ports combined with K0 ~ K3 determine the destination.
41 TAPE IN I H: Tape ON, L: Tape OFF.
42 POWER CHECK I A/D in for power supply voltage level.
43 REMOTE I A/D in for remote controller.
44 POWER SW O H: Power OFF, L: Power ON.
45 HOLD I H: Hold ON, L: Hold OFF.
46 BUZZER O Buzzer output.
47 MUTE O Mute output.
48 TEST - Microcontroller test terminal (Not used).
49 WAKE UP I Wake up the system from memory back-up mode.
50 IF IN I IF frequency input.
51 TU OUT O L: Tuner ON.
52 PLL OUT O Phase comparison output.
53 GND - GND.
54 FM IN I Not used.
55 AM IN I AM oscillator signal input.
56 VDD - Supply voltage terminal.
57 RESET I System reset input.
58 XOUT
59 XIN
60 VXT - Power supply for crystal oscillator.
61 VLCD - Reference voltage for LCD driver (Not connected).
62, 63 C1,C2 Voltage doubler boosting.
64 VEE - Constant 1.5V for LCD driver.
IC, TC9318FB-046<EXCEPT 591YU >
IC DESCRIPTION
Crystal oscillator pin.I/O
Pin No. Pin Name I/O Description
7 8
Page 6
109
AA
BB
CC
DD
EE
FF
GG
HH
II
JJ
KK
LL
MM
NN
OO
PP
QQ
RR
SS
TT
UU
Page 7
SCHEMATIC DIAGRAM - 1 (MAIN: 591YU)
11 12
Page 8
1413
AA
BB
CC
DD
EE
FF
GG
HH
II
JJ
KK
LL
MM
NN
OO
PP
QQ
RR
SS
TT
UU
Page 9
SCHEMATIC DIAGRAM - 2 (MAIN:EXCEPT 591YU 494YZ) *NOTE:494YZ indicates-01 PWB information
15 16
Page 10
1817
AA
BB
CC
DD
EE
FF
GG
HH
II
JJ
KK
LL
MM
NN
OO
PP
QQ
RR
SS
TT
UU
Page 11
SCHEMATIC DIAGRAM - 3 (MAIN:494YZ) *NOTE:494YZ indicates-11 PWB information
2019
Page 12
7) Finally re-check the tape speed.
Caution : Cool the patterns down to normal tempera-
ture after soldering. If the pattern remains
heated,the gorvernor circuit does not
operate normally.
<RADIO SECTION>
1. AM IF Adjustment
IFT201..................................................................450kHz
2. AM VT Check
Settings: Test point: TP1 (VT)
Method: Set to AM 530kHz and check the TP1 is
1.0V-0.2/+0.3V. Then set to AM 1710kHz
and check the test point is less than 10.0V.
3. AM Tracking Adjustment
L206.....................................................................630kHz
CT202<591YU ONLY>................................... 1440kHz
CT201<EXCEPT 591YU>...............................1440kHz
4. FM VT Adjustment
Settings: Test point TP1(VT)
Adjustment location ................................................L204
Method:` Set to FM 59.75MHz<591YU>,76MHz
<EXCEPT 591YU> and adjust L204 so that
the testpoint becomes 0.9V±0.1V. Then set
to FM108.1MHz and check that the test
point is less than 12.0V.
5. FM Tracking Adjustment
L202................................................................. 87.5MHz
6. TV VT Adjustment<591YU ONLY>
Settings: Test point TP1(VT)
Adjustment location ................................................L203
Method: Set to TV 2ch and adjust L203 so that
the test point becomes 1.0V±0.1V. Then set
to TV13 ch and check that the test point is
less than 12.0V.
7. TV Tracking Ajustment<591YU ONLY>
L201.......................................................................... 1 ch
9. GOVERNER Adjustment
Perform the STOP > PLAY and REVERSE operations
(or PAUSE ON > OFF) after the motor is replaced.
When the tape starts running smooth, this adjustment
is not necessary. If wow is conspicuous at the beginning
of the tape-run, perform this adjustment following the
procedures below.
1) Solder resistor pattern of the MOTOR AND
GOVERNOR MATCHING ADJ. resistor group.
2) Set the tape speed (using speed adjustment SFR101).
3) Restrict the motor rotation by hand(or turn PAUSE ON).
4) Remove your hand and listen to the beginning of the
tape-run.
<TAPE PLAYER SECTION>
8. Tape Speed Adjustment
Settings: Test tape : TTA100
Test point : HEADPHONE (J001)
Adjustment location : SFR101
Supper BASS: OFF
Tape select: NORM
Direction: FWD
Volume: MAX10dB
Method: Play back the test tape and adjust for
3000Hz±60Hz (FWD) and confirm the
the test tape 3000Hz±60Hz (RVE).
<591YU ONLY>
<EXCEPT 591YU>
5) When the rise of tape running is smooth, no more
adjustment is necessary.
If wow continues for 1 to 2 seconds at the rise time,
change the combined resistance according to procedure
6 and check that the tape starts running smooth.
6) Solder the resistor pattern according to the table below
Solder
SolderSolder
Solder
Ope n Solder
Pattern
(Procedure
1 above)
Step (1) Step (2)
Medium
resistance(B)
Low
resistance(A)
High
resistance(C)
OpenOpen
Open
Solder
Solder
Solder
Solder
Open
Solder
Pattern
(Procedure
1 above)
Step (1)
Step (2)
Medium
resistance(B)
Low
resistance(A)
High
resistance(C)
Open
Open
Open
21 22
*TP1(VT)
*SFR101
8
9
4
6
*TP1(VT)
2
8
9
4
6
*SFR101
A
B
C
A
B
C
Page 13
PRACTICAL SERVICE FIGURE
<TUNER SECTION>
Sensitivity :
(IHF, THD 3%) FM Less than 17dB [at 87.5MHz]
Less than 17dB [at 98.1MHz]
Less than 17dB [at 108.1MHz]
TV<591YU ONLY>
Less than 19dB [at 2ch]
Less than 19dB [at 4ch]
Less than 19dB [at 7ch]
Less than 19dB [at 10ch]
Less than 19dB [at 13ch]
WEATHER<591YU ONLY>
Less than 19dB [at 2ch ]
(S/N 10dB) AM Less than 57dB [at 630kHz]
Less than 56dB [at 1000kHz]
<YU ONLY>
Less than 56dB [at 999kHz]
<EXCEPT YU>
Less than 56dB [at 1440kHz]
S/N Ratio : FM More than 51dB [at 87.5MHz]
More than 51dB [at 98.1MHz]
More than 51dB [at 108.1MHz]
AM More than 25dB [at 630kHz]
More than 25dB [at 1000kHz]
<YU ONLY>
More than 25dB [at 999kHz]
<EXCEPT YU>
More than 25dB [at 1440kHz]
Intermediate frequency : FM 10.7MHz ± 0.1MHz
AM 450kHz ± 3kHz
FM stereo separation : More than 17dB [at 98.1MHz]
<TAPE SECTION>
Tape speed : 3000Hz ± 60Hz
Wow & flutter : Less than 0.55%
Distortion : Less than 3.0%
Take-up torque : 30g-cm-6/+15g-cm(FWD)
30g-cm-6/+15g-cm(RVS)
Back tension: 2.5g-cm-1.0/+1.5g-cm(FWD)
2.5g-cm-1.0/+1.5g-cm(RVS)
F.F torque : 110g-cm±40g-cm
Rew torque : 110g-cm±40g-cm
S/N ratio : More than 43dB
Noise level : Less than 4.0mV
(Vol MAX, without tape)
Less than 0.3mV
(Vol MIN, without tape)
Frequency response : 63Hz 3.5/±4.0dB ~ 8kHz 0/± 4
dB(NORM)
63Hz 3.5/±4.0dB ~ 8kHz 0/± 4
dB(CrO2, METAL)
Test tape : TTA 100
TTA 210
TTA 310(70us)
TTA 320 (120us)
23
Page 14
MECHANICAL EXPLODED VIEW 1/1
1
3
8ZM-3 P3N
(494YZ[LM] Only)
8ZM-3 P2N
(EXCEPT 494YZ[LM])
BAR ANT
6
7
MAIN C.B
(591YU
Only)
2
4
5
D
B
B
C
D
9
8
20
19
15
10
18
11
12
13
14
16
17
A
E
24
Page 15
MECHANICAL PARTS LIST 1/1
PART NO. KANRI
1 8Z-HRB-035-010 LID,CASS R BLU EG<494YZ1[L]>
1 8Z-HRB-001-010 LID,CASS R GRY<EXCEPT 594YZ1[S],596YZ1[S],494YZ1[S],494YZ1[L],496YZ1[S]>
1 8Z-HRB-018-010 LID,CASS R GRY EG<594YZ1[S],596YZ1[S],494YZ1[S],496YZ1[S]>
2 8Z-HRB-217-110 SPR-T,CASS<EXCEPT 591YU[S],496YL[S],494YU[S]>
2 8Z-HRB-217-010 SPR-T,CASS<591YU[S],496YL[S],494YU[S]>
3 8Z-HRB-002-010 WINDOW,CASS
4 8Z-000-000-000 PLATE SPRING,CASSETTE
5 8Z-000-000-000 HOLD,JACK
6 8Z-HRB-201-110 HLDR,BAR-ANT<EXCEPT 591YU[S],496YL[S],494YU[S]>
6 8Z-HRB-201-010 HLDR,BAR-ANT<591YU[S],496YL[S],494YU[S]>
7 8Z-HRB-209-010 BAT-CONTACT,M
8 8Z-HRB-038-110 LID,BAT BLU<494YZ1[L]>
8 8Z-HRB-005-110 LID,BAT SIL<EXCEPT 591YU[S],496YL[S],494YU[S],494YZ1[L]>
8 8Z-HRB-005-010 LID,BAT SIL<591YU[S],496YL[S],494YU[S]>
9 8Z-HRB-208-010 BAT-CONTACT,P
10 8Z-HRB-203-110 HLDR,KNOB RTRY<EXCEPT 591YU[S],496YL[S],494YU[S]>
10 8Z-HRB-203-010 HLDR,KNOB RTRY<591YU[S],496YL[S],494YU[S]>
11 8Z-HRB-212-010 SPR-T,HOLD
12 8Z-HRB-004-010 CABI,REAR SIL<EXCEPT 494YZ1[L]>
13 8Z-HRB-011-010 KEY,RBR PRESET R
14 8Z-HRB-009-010 KEY,RBR PRESET L
15 8Z-HRB-010-010 KEY,PRESET R<EXCEPT 494YU[S],594YZ1[S],494YZ1[S],494YZ1[L]>
15 8Z-HRB-034-010 KEY,PRESET R SIL<494YU[S],594YZ1[S],494YZ1[S],494YZ1[L]>
16 8Z-HRB-008-010 KEY,PRESET L<EXCEPT 494YU[S],594YZ1[S],494YZ1[S],494YZ1[L]>
16 8Z-HRB-033-010 KEY,PRESET L SIL<494YU[S],594YZ1[S],494YZ1[S],494YZ1[L]>
17 8Z-HRB-037-010 CABI,REAR BLU<494YZ1[L]>
17 8Z-HRB-021-010 PANEL,REAR 494<494YU[S]>
17 8Z-HRB-022-010 PANEL,REAR 494 EG<494YZ1[S],494YZ1[L]>
17 8Z-HRB-006-010 PANEL,REAR 496<496YL[S],496YL1[S],496YH1[S],496YJ1[S]>
17 8Z-HRB-019-010 PANEL,REAR 496 EG<496YZ1[S]>
17 8Z-HRB-020-010 PANEL,REAR 591 WT<591YU[S]>
17 8Z-HRB-025-010 PANEL,REAR 594 EG<594YZ1[S]>
17 8Z-HRB-023-010 PANEL,REAR 596<596YL1[S],596YH1[S],596YJ1[S]>
17 8Z-HRB-024-010 PANEL,REAR 596 EG<596YZ1[S]>
18 8Z-HRB-013-010 KNOB,RTRY HOLD
19 8Z-HRB-007-010 KEY,BAND
20 8Z-HRB-012-010 KEY,RBR TUN
A 87-B10-048-010 VT2+1.4-3 (3) CR HL
B 87-B10-196-010 VT2+1.4-4 BLK (3) HL
C 87-264-527-310 V 1.7-3 SCREW
D 87-067-732-010 TAPPING SCREW, VT1.4-3
E 87-067-384-010 SCREWVT1.4-3.5HL
NO.
DESCRIPTIONREF. NO. KANRI
REF. NO. DESCRIPTIONPART NO.
NO.
Basic color Color Basic color Color Basic color Color
symbol symbol symbol
B Black C Cream D Orange
G Green H Gray L Blue
LT Transparent Blue N Gold P Pink
R Red S Silver ST Titan Silver
T Brown V Violet W White
WT Transparent White Y Yellow YT Transparent Yellow
LM Metallic Blue LL Light Blue GT Transparent Green
LD Dark Blue DT Transparent Orange
COLOR NAME TABLE
25
Page 16
TAPE MECHANIISM EXPLODED VIEW 1/1(8ZM-3 P2N:EXCEPT 494YZ[LM])
38
30
32
31
33
36
W-P1.16-2.8-0.4
39
37
25
23
9
40
34
17
16
35
41
43
44
18
47
46
15
14
26
27
28
29
24
22
21
20
19
12
10
A
7
6
A
7
11
8
29
13
49
42
45
39
48
50
51
52
53
54
55
56
57
1
2
5
3
4
8ZM-3
26
Page 17
TAPE MECHANISM PARTS LIST 1/1(8ZM-3 P2N:EXCEPT 494YZ[LM])
PART NO. KANRI
1 8Z-HRB-003-010 FRAME,CENTER GRY
2 8Z-HRB-207-110 SPR-P,CASS
3 88-ZM3-253-110 SPR-C,BT L
4 88-ZM3-274-010 GEAR,REEL A
5 8Z-HRB-014-010 KNOB,SL OPEN
6 8Z-HRB-204-110 LEVER,EJECT
7 8Z-HRB-216-110 CAP, EJECT
8 8Z-HRB-205-010 SPR-T,EJECT
9 8Z-HRB-215-010 SHAFT,ASSY
10 87-A91-379-010 MOT,BCY3B-13
11 88-ZM3-236-010 PULLEY,MOT S
12 88-ZM3-263-210 BELT,S
13 88-ZM3-243-010 SPR-T,PLAY BACK
14 8Z-HRB-206-010 PLATE,EJECT
15 88-ZM3-217-110 ARM,PINCH L
16 88-ZM3-241-010 SPR-T,PINCH L
17 88-ZM3-003-110 LEVER,REW
18 88-ZM3-246-110 SPR-T,FF REW
19 87-A80-115-010 F-CABLE,5P P2
20 87-A91-019-010 HEAD ASSY,PH 8ZM-3
21 88-ZM3-211-010 LEVER,DIR
22 88-ZM3-001-110 LEVER,PLAY
23 88-ZM3-213-110 LEVER,T-UP
24 88-ZM3-225-110 GEAR,PLAY
25 88-ZM3-224-110 GEAR,TRANSMIT
26 88-ZM3-002-010 LEVER,FF
27 88-ZM3-242-110 SPR-T,PINCH R
28 88-ZM3-218-010 ARM,PINCH R
29 88-ZM3-271-010 ROLLER ASSY,PINCH
30 88-ZM3-220-010 BTN,MODE SEL
NO.
DESCRIPTIONREF. NO. KANRI
REF. NO. DESCRIPTIONPART NO.
31 88-ZM3-267-010 SHAFT,PULLEY TWIN
32 88-ZM3-234-010 PULLEY,BELT TWIN
33 88-ZM3-212-010 LEVER,LOCK
34 88-ZM3-245-110 SPR-T,LOCK
35 88-ZM3-201-110 CHAS ASSY,OUTSERT P
36 88-ZM3-216-010 LEVER,SW
37 88-ZM3-221-110 GEAR,AUTO
38 88-ZM3-240-010 FLY-WHL,R S
39 88-ZM3-266-010 CAPSTAN, 1.5-NS
40 88-ZM3-248-010 SPR-T,AUTO CHOOSE
41 88-ZM3-215-010 LEVER,AUTO KICK
42 88-ZM3-262-010 BELT,L
43 88-ZM3-244-010 SPR-T,DIR
44 88-ZM3-219-010 BTN,DIR KNOB
45 88-ZM3-239-010 FLY-WHL,L S
46 88-ZM3-226-010 GEAR,IDLE
47 88-ZM3-004-110 LEVER,STOP
48 88-ZM3-255-110 SPR-C,STOP
49 88-ZM3-214-010 LEVER,AUTO FIND
50 88-ZM3-238-010 CAP,SLIP
51 88-ZM3-252-010 SPR-C,SHIFT
52 88-ZM3-251-210 SPR-C,SLIP
53 88-ZM3-222-010 GEAR,SLIP FAST
54 88-ZM3-269-010 FELT,SLIP
55 88-ZM3-237-010 CLR,SLIP
56 88-ZM3-247-010 SPR-T,AUTO FIND
57 88-ZM3-223-010 GEAR,SLIP SLOW
A 87-067-384-010 SCREWVT1.4-3.5HL
NO.
27
Page 18
TAPE MECHANIISM EXPLODED VIEW 1/1(8ZM-3 P3N:494YZ[LM] ONLY)
38
W-P1.16-2.8-0.4
36
39
37
30
32
31
33
25
23
12
26
24
21
27
28
11
29
19
20
29
22
13
17
34
16
18
15
35
41
40
44
47
46
43
48
49
42
45
39
50
51
52
53
54
55
10
A
9
7
6
A
7
8
5
14
1
3
4
56
57
2
28
Page 19
TAPE MECHANISM PARTS LIST 1/1(8ZM-3 P3N:494YZ[LM] ONLY)
PART NO. KANRI
1 8Z-HRB-036-010 FRAME,CENTER BLU
2 8Z-HRB-207-110 SPR-P,CASS
3 88-ZM3-253-110 SPR-C,BT L
4 88-ZM3-274-010 GEAR,REEL A
5 8Z-HRB-014-010 KNOB,SL OPEN
6 8Z-HRB-204-110 LEVER,EJECT
7 8Z-HRB-216-110 CAP, EJECT
8 8Z-HRB-205-010 SPR-T,EJECT
9 8Z-HRB-215-010 SHAFT,ASSY
10 87-A91-379-010 MOT,BCY3B-13
11 88-ZM3-236-010 PULLEY,MOT S
12 88-ZM3-263-210 BELT,S
13 88-ZM3-243-010 SPR-T,PLAY BACK
14 8Z-HRB-206-010 PLATE,EJECT
15 88-ZM3-217-110 ARM,PINCH L
16 88-ZM3-241-010 SPR-T,PINCH L
17 88-ZM3-003-110 LEVER,REW
18 88-ZM3-246-110 SPR-T,FF REW
19 87-A80-115-010 F-CABLE,5P P2
20 87-A91-019-010 HEAD ASSY,PH 8ZM-3
21 88-ZM3-211-010 LEVER,DIR
22 88-ZM3-001-110 LEVER,PLAY
23 88-ZM3-213-110 LEVER,T-UP
24 88-ZM3-225-110 GEAR,PLAY
25 88-ZM3-224-110 GEAR,TRANSMIT
26 88-ZM3-002-010 LEVER,FF
27 88-ZM3-242-110 SPR-T,PINCH R
28 88-ZM3-218-010 ARM,PINCH R
29 88-ZM3-271-010 ROLLER ASSY,PINCH
30 88-ZM3-220-010 BTN,MODE SEL
NO.
DESCRIPTIONREF. NO. KANRI
REF. NO. DESCRIPTIONPART NO.
31 88-ZM3-267-010 SHAFT,PULLEY TWIN
32 88-ZM3-234-010 PULLEY,BELT TWIN
33 88-ZM3-212-010 LEVER,LOCK
34 88-ZM3-245-110 SPR-T,LOCK
35 88-ZM3-201-110 CHAS ASSY,OUTSERT P
36 88-ZM3-216-010 LEVER,SW
37 88-ZM3-221-110 GEAR,AUTO
38 88-ZM3-240-010 FLY-WHL,R S
39 88-ZM3-266-010 CAPSTAN, 1.5-NS
40 88-ZM3-248-010 SPR-T,AUTO CHOOSE
41 88-ZM3-215-010 LEVER,AUTO KICK
42 88-ZM3-262-010 BELT,L
43 88-ZM3-244-010 SPR-T,DIR
44 88-ZM3-219-010 BTN,DIR KNOB
45 88-ZM3-239-010 FLY-WHL,L S
46 88-ZM3-226-010 GEAR,IDLE
47 88-ZM3-004-110 LEVER,STOP
48 88-ZM3-255-110 SPR-C,STOP
49 88-ZM3-214-010 LEVER,AUTO FIND
50 88-ZM3-238-010 CAP,SLIP
51 88-ZM3-252-010 SPR-C,SHIFT
52 88-ZM3-251-210 SPR-C,SLIP
53 88-ZM3-222-010 GEAR,SLIP FAST
54 88-ZM3-269-010 FELT,SLIP
55 88-ZM3-237-010 CLR,SLIP
56 88-ZM3-247-010 SPR-T,AUTO FIND
57 88-ZM3-223-010 GEAR,SLIP SLOW
A 87-067-384-010 SCREWVT1.4-3.5HL
NO.
ACCESSORIES / PACKAGE LIST
If cant understand for Description please kindly refer to REFERENCE NAME LIST .
PART NO.
1 8Z-HRB-050-010 CLIP,BELT ASSY
2 87-B30-258-010 HEADPHONE,HP-M007B(F)<EXCEPT *1>
2 87-B30-092-010 HEADPHONE,HP-MR015(F)<*1>
3 8Z-HRB-904-010 IB,YHJ(ECC)S 496<496YH,496YJ>
3 8Z-HRB-914-010 IB,YHJ(ECC)S 596<596YH,596YJ>
3 8Z-HRB-906-010 IB,YL(3L)S<496YL1BSF>
3 8Z-HRB-916-010 IB,YL(3L)S 596<596YL1SF>
3 8Z-HRB-907-010 IB,YZ(EGF)S494/496<494YZ,496YZ>
3 8Z-HRB-917-010 IB,YZ(EGF)S594/596<594YZ,596YZ>
3 8Z-HRB-909-010 IB,YZ(PHNCZ)S494/496<494YZ,496YZ>
3 8Z-HRB-919-010 IB,YZ(PHNCZ)S594/596<594YZ,596YZ>
3 8Z-HRB-908-010 IB,YZ(SID)S 494/496<494YZ,496YZ>
3 8Z-HRB-918-010 IB,YZ(SID)S594/596<594YZ,596YZ>
NOTE: *1:596YL,594YZ,596YH,596YJ,596YZ
NO.
DESCRIPTIONREF. NO. KANRI
29
Page 20
A4
L
2-11, IKENOHATA 1-CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111
211, IKENOHATA 1CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111
9820572 931261
Printed in Singapore
Loading...