MECHANICAL PARTS LIST 1/1 ........................................................................................................... 55
CD MECHANISM EXPLODED VIEW 1/1 ............................................................................................. 56
CD MECHANISM PARTS LIST 1/1 ...................................................................................................... 56
REFERENCE NAME LIST .................................................................................................................... 57
2
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully the
instructions below when servicing.
WARNING!
WHEN SERVICING, DO NOT APPROACH THE LASER EXIT
WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO
CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE
FROM A DISTANCE OF MORE THAN 30cm FROM THE
SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL
PICK-UP BLOCK.
Caution: Invisible laser radiation when
open and interlocks defeated avoid exposure to beam.
Advarsel:Usynling laserståling ved åbning,
når sikkerhedsafbrydere er ude af funktion.
Undgå udsættelse for stråling.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa käyt-täjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.
VARNING!
Om apparaten används på annat sätt än vad som specificeras i
denna bruksanvising, kan användaren utsättas för osynling
laserstrålning, som överskrider gränsen för laserklass 1.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
ATTENTION
L'utilisation de commandes, réglages ou procédures autres que
ceux spécifiés peut entraîner une dangereuse exposition aux
radiations.
ADVARSEL!
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude
af funktion. Undgå udsættelse for stråling.
This Compact Disc player is classified as a CLASS 1 LASER
product.
The CLASS 1 LASER PRODUCT label is located on the rear
exterior.
CLASS 1
KLASSE 1
LUOKAN 1
KLASS 1
LASER PRODUCT
LASER PRODUKT
LASER LAITE
LASER APPARAT
Precaution to replace Optical block
(KSS-213B)
Body or clothes electrostatic potential could ruin
laser diode in the optical block. Be sure ground
body and workbench, and use care the clothes
do not touch the diode.
1) After the connection, remove solder shown in
the right figure.
3
DISASSEMBLY INSTRUCTIONS
1. How to replace PICK UP.
1) Open the TRAY.
Push the stopper to arrow direction and release half of
the SHAFT SLED.
2) Turn GEAR MAIN CAM to the counterclockwise
(arrow “a”) direction, and lift up CD mechanism. (Fig-1)
3) Remove SHAFT SLED.
4) CD mechanism in down position, replace PICK UP.
5) Lift up CD mechanism (Fig-1), and Reassemble the
SHAFT SLED.
PICKUP
SHAFT SLED
STOPPER
a
2. How to remove the 5CD CHANGER BLOCK
(Fig-2)
1) Remove the two FFC of the CD circuit board, and
remove the five SCREWS.
2) Lift 5 CD CHANGER BLOCK from behind, and
remove it. (5CD CHANGER BLOCK can be removed
even if PANEL TRAY is not removed.)
FFC
SCREW
GEAR MAIN CAM
5CD CHANGER BLOCK
Fig-1
LIFT UP
FFC
Fig-2
4
3. The disassemble and reassemble the TRAY
5CD CHANGER BLOCK
BOSS
b
3-1. Disassembling procedure.
1) Push the PLATE GEAR’S Boss at the bottom part of
CHAS MECHA strongly to the outside (arrow “b”
direction). (Fig-3)
(Confirm that TRAY appears a little in the front.)
2) Draw TRAY to the open position.
3) Remove FFC, and push the two LEVERS at both side of
the CHAS MECH to remove TRAY. (Fig-4)
TRAY
LEVER
FFC
LEVER
3-2. Reassembling procedure.
1) Confirm that LEVER TRAY is at the most right position
and check for the CD Mechanism to be in the down
position. (Fig-5)
2) Push in the TRAY along the rail of the CHAS MECHA.
Fig-3
Fig-4
3) After TRAY is half closed and FFC is put in, it can enter
by force until the end of TRAY closed. (Fig-6)
FFC
TRAY
LEVER TRY
Fig-5
Fig-6
5
4. How to reassemble the TURN TABLE. (Fig-7)
1) Push LEVER TT in the direction of “C”, and put in the
TURN TABLE 5CD. (Fig-7)
After reassembly, one of the TURN TABLE DISC
TRAY (can be either one of the five disc trays) must be
aligned with TURN TABLE 5CD. (Fig-8)
That is, having no gap difference between the TURN
TABLE 5CD and the TRAY 5CD.
*When reassembling the TURN TABLE 5CD, it is
acceptable facing any CD number (1-5).
ALIGN
C
LEVER TT
Fig-7Fig-8
TURN TABLE 5CD
TRAY 5CD
6
ELECTRICAL MAIN PARTS LIST
REF. NOPART NO.KANRIDESCRIPTION
NO.
IC
87-A20-547-010 C-IC,CXA1992AR<EXCEPT YSDFNSHCM>
C116 87-010-197-080 CAP, CHIP 0.01 DM
C117 87-010-369-080 C-CAP,S 0.033-25 K B
C118 87-010-197-080 CAP, CHIP 0.01 DM
C119 87-010-369-080 C-CAP,S 0.033-25 K B
C120 87-010-197-080 CAP, CHIP 0.01 DM
C121 87-010-494-040 CAP,E 1-50 GAS
C122 87-010-154-080 CAP CHIP 10P
C123 87-010-154-080 CAP CHIP 10P
C124 87-010-154-080 CAP CHIP 10P
C125 87-010-596-080 CAP, S 0.047-16
C126 87-010-596-080 CAP, S 0.047-16
C127 87-012-140-080 CAP 470P
C128 87-010-596-080 CAP, S 0.047-16
C129 87-010-198-080 CAP, CHIP 0.022
C130 87-016-081-080 C-CAP,S 0.1-16 RK
C131 87-010-550-040 CAP,E 100-6.3 GAS
C132 87-010-550-040 CAP,E 100-6.3 GAS
C133 87-012-158-080 C-CAP,S 390P-50 CH
C150 87-010-145-080 C-CAP,S 1P-50 CH
C202 87-010-596-080 CAP, S 0.047-16
CON3 87-A60-133-010 CONN,8P V FE
CON5 87-A60-154-010 CONN,6P H FE
CON6 87-A60-162-010 CONN,14P H FE
JR9 83-XM1-617-080 C-COIL,BK2125HM601
JR28 83-XM1-617-080 C-COIL,BK2125HM601
R102 87-022-363-080 C-RES,S 68K-1/10W F
R103 87-022-363-080 C-RES,S 68K-1/10W F
R104 87-022-363-080 C-RES,S 68K-1/10W F
R105 87-022-365-080 C-RES,S 100K-1/10W F
R106 87-022-365-080 C-RES,S 100K-1/10W F
86-ZG1-667-010 F-CABLE,8P 1.25 175MM BLACK
C101 87-010-182-080 C-CAP,S 2200P-50 B
C102 87-016-669-080 C-CAP,S 0.1-25 K B
C103 87-016-669-080 C-CAP,S 0.1-25 K B
C104 87-016-669-080 C-CAP,S 0.1-25 K B
C105 87-010-404-040 CAP,E 4.7-50 SME
C106 87-010-369-080 C-CAP,S 0.033-25 K B
C107 87-010-197-080 CAP, CHIP 0.01 DM
C108 87-010-401-040 CAP,E 1-50 SME
C109 87-010-382-040 CAP,E 22-25 SME
C110 87-010-213-080 C-CAP,S 0.015-50 B
C111 87-010-263-040 CAP,E 100-10
C112 87-010-197-080 CAP, CHIP 0.01 DM
C113 87-010-369-080 C-CAP,S 0.033-25 K B
C114 87-010-369-080 C-CAP,S 0.033-25 K B
C115 87-010-369-080 C-CAP,S 0.033-25 K B
C116 87-012-158-080 C-CAP,S 390P-50 CH
C117 87-012-154-080 C-CAP,S 150P-50 CH
C118 87-010-401-040 CAP,E 1-50 SME
C119 87-010-311-080 CAP 12P
C120 87-010-596-080 CAP, S 0.047-16
REF. NOPART NO.KANRIDESCRIPTION
NO.
C121 87-010-596-080 CAP, S 0.047-16
C123 87-016-669-080 C-CAP,S 0.1-25 K B
C125 87-010-198-080 CAP, CHIP 0.022
C126 87-016-669-080 C-CAP,S 0.1-25 K B
C127 87-010-263-040 CAP,E 100-10
C956 87-010-805-080 CAP, S 1-16
C957 87-010-805-080 CAP, S 1-16
C958 87-010-805-080 CAP, S 1-16
C959 87-010-805-080 CAP, S 1-16
C960 87-010-805-080 CAP, S 1-16
CN3 86-ZG1-609-010 CONN ASSY,6P
CN3 87-A60-133-010 CONN,8P V FE
CN6 87-A60-160-010 CONN,12P H FE
CN7 86-ZG1-606-010 CONN ASSY 2P
CN7 86-ZG1-606-010 CONN ASSY 2P
CN101 87-A60-424-010 CONN,16P V TOC-B
CN102 87-009-034-010 CONN,6P PH V
CN301 87-A60-154-010 CONN,6P H FE
CN302 86-ZG1-620-010 CONN ASSY,2P VIDEO-SW
CN851 87-A60-109-010 CONN,2P V S2M-2W
• Regarding connectors, they are not stocked as they are not the initial order items.
The connectors are available after they are supplied from connector manufacturers upon the order is received.