FCC Compliance Statement:
This device complies with Part 15 of the FCC Rules. Operation is
subjected to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with limits for a
Class B digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference in residential
installations. This equipment generates, uses, and can radiate radio frequency energy, and if
not installed and used in accordance with the instructions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause interference to radio or television equipment reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Move the equipment away from the receiver.
-Plug the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/television technician for additional suggestions.
You are cautioned that any change or modications to the equipment not expressly approved
by the party responsible for compliance could void Your authority to operate such equipment.
If the time arises to throw away your product, please
recycle all the components possible.
Batteries and rechargeable batteries are not to be
disposed in your domestic waste! Please recycle
them at your local recycling point.
Together we can help to protect the environment.
Welcome:
Dear user, thank you for purchasing this product.
Much investment in time and effort has gone into its development, and it is our hope
that it will give you many years of trouble-free service.
Safety Notice:
1. Do not drop, puncture or disassemble the camcorder; otherwise the warranty will be voided.
2. Avoid all contact with water, and dry hands before using.
3. Do not expose the camcorder to high temperature or leave it in direct sunlight. Doing so may
damage the camcorder.
4. Use the camcorder with care. Avoid pressing hard on the camcorder body.
5. For your own safety, avoid using the camcorder when there is a storm or lightning.
6. Do not use batteries of different specications. Doing so may lead to the potential for serious
damage.
7. Remove the battery during long periods between usage, as a deteriorated battery may affect
the functionality of the camcorder.
8. Remove the battery if it shows signs of leaking or distortion.
9. Use only the accessories supplied by the manufacturer.
10. Keep the camcorder out of the reach of infants.
11. Risk of explosion if battery is replaced by an incorrect type.
12. Dispose of used batteries according to the instructions.
1
EN
Preparing the Camcorder
Product overview
Playback
As Joystck Up: Icon
Down: Video resolution
Left: Flash
Right: Menu
Record
Delete
Connector cover
Shutter
HDMI outputTV-out /
earphone
connector
Tripod socket
SD card slot
Power
SpeakerLCD display
Zoom out/Volume down
Zoom in/Volume up
Battery cover
Wrist strap
holder (back)
USB connector
Wrist strap
holder (front)
Lens
Flash strobe
Microphone
LED indicator
Focus switch
*For select model
only.
2
EN
EN
1
Detach the USB connector as indicated,
and then unfasten the battery cover to
remove the cover.
2
Place the accessory Li-Ion battery into
the compartment. Note that the metallic
contacts must be aligned with the
contacts in the compartment.
3
Replace the cover.
When using for the rst time, please fully charge the battery
for at least 8 hours.
Getting Started
Loading the battery
1
Lift the memory card cover to open it as indicated.
2
Insert the card as the direction of indication until it
reaches the end of the slot.
3
When the card is inserted successfully, the icon ( )
will appear on screen. To remove the card, push the
card to release it and then pull it out gently.
4
Put the cover back.
1
Detach the USB connector and plug it into a USB port on a powered PC. Make
sure the camcorder is powered off.
2
The charging LED turns red and the charge starts.
3
When the charging is interrupted or the battery pack is fully charged, the charging
LED will turn off.
When using a PC to charge the battery:
1) Do not power on the camcorder or the
charge will stop.
2) If necessary, use a USB extension
cable to extend the connection.
Charging the battery
If the power is not turned on after you have completed the above procedures, please
check the following have been done correctly: 1) The battery is correctly loaded; 2) The
loaded battery has enough power.
Please choose your local language before starting using the camcorder.
Loading...