@n IP Company
AIPTEK PENCAM 2
Installation Guide
Contents
FCC Statement
ECC Statement
End User License Agreement
Contents Checklist
System Requirements
Specifications
Operating Environment
How to Use Your PenCam
Switching the camera on
Taking a picture
Additional features
Self Timer
Continuous mode
Clearing the stored images
Changing the picture resolution
How to Upload Photo & Video to PC
Start AIPTEK PenCam Manager
Mode Selecting
PC Camera Mode
DSC Mode
Uploading Photos
Editing Photos
Uploading Video
AVI Creator
Playing Video
Image processing
Mail Function
Troubleshooting
How To Obtain A Warranty Service
Statement of Limited Warranty
1
2
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
22
@n IP Company
FCC Statement
This equipment generates and uses radio frequency energy and if not
installed and used in accordance with the manufacturer's instructions, it
may cause interference to radio and television reception. This equipment
has been tested and certified to comply within the limits of Section 15(J) of
FCC Regulations for Class B computing devices. These regulations are desi
gned to provide reasonable protection against such interference in a residential installation. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause interference to radio or television reception (which can be determined by turning the
equipment on and off), the user is encouraged to attempt to correct the interference by following the
following steps:
Reorient the antenna of the radio or television
Relocate the computer with respect to the radio or television receiver
Plug the computer into a different power outlet so that the computer and receiver are on different
electrical branch circuits.
If necessary, the user should consult with the dealer or an experienced radio/television technician for
additional help and suggestions. The user may find the following booklet, prepared by the FCC,
helpful in solving radio/television interference problems:
"How to Identify and Resolve Radio-TV Interference Problems"
This booklet is available by sending a written request to:
U.S. Government Printing Office
Washington D.C., 20402
Request Stock Number 004-000-0345-4.
ECC Statement
This device complies with the requirements of EEC directive 89/336/EEC with
regard to Electromagnetic Compatibility.
Dieses Greät entspricht den Anforderungen der EEC-Richtlinie 89/336/EEC für
elektromagnetische Verträglichkeit.
Cet appareil est conforme aux exigences de la directive de la Communauté européenne 89/336/EEC
sur la compatibilité électromagnétique.
Questo Apparecchio è conforme alla direttiva comunitaria 89/336/CEE relativa alla compatibilità
elettromagnetica.
Este dispositivo cumple con los requerimientos de la normativa de la CEE 89/336/EEC en lo
referente a Compatibilidad Electromagnética.
..1..
End User License Agreement
This AIPTEK End-User License Agreement ("EULA") is a legal agreement between you (either an
individual or a single entity) and AIPTEK, Inc. for the AIPTEK hardware product identified above. This
includes the computer hardware, software, associated media, printed materials, and "online" or
electronic documentation ("HARDWARE PRODUCT").
installing, copying, or otherwise using this HARDWARE PRODUCT, you agree to be bound by
the terms of this EULA.
use the HARDWARE PRODUCT, and we recommend that you return it to the place where you
purchased it from.
The HARDWARE PRODUCT is protected by copyright laws and international copyright treaties, as
well as other intellectual property laws and treaties. The HARDWARE PRODUCT is licensed, not
sold.
1. GRANT OF LICENSE. This EULA grants you the following rights:
Hardware - You may install the HARDWARE PRODUCT on one single computer. If you have more
than one computer that you would like to install the HARDWARE PRODUCT on, you may install
the HARDWARE PRODUCT onto that other computer, provided that you are the only person that
will use the HARDWARE PRODUCT on each computer system.
Software - You may install the additional software included with this HARDWARE PRODUCT on
one single computer, provided that you agree to the individual EULAs for each software program.
If you have more than one computer that you would like to install the additional software that came
with the HARDWARE PRODUCT on, you may install the additional software onto that other
computer, provided that you are the only person that will use the additional software on each
computer system.
Copies - You may make one copy of each disk and CD included with the HARDWARE PRODUCT
for backup purposes only, provided that you do not lease, lend, rent, or otherwise allow others to
have possession of the copies.
2. OTHER RIGHTS AND LIMITATIONS
Single Entity User - Only the person that the HARDWARE PRODUCT was purchased for may use
the HARDWARE PRODUCT and its accompanying software.
Individual User - Only you and those in your immediate household may use the HARDWARE
PRODUCT and its accompanying software.
Product Transfer - You may permanently transfer all of the HARDWARE PRODUCT under this
EULA, provided you retain no copies of any of the software included in this HARDWARE
PRODUCT. To do this, you must transfer all of the HARDWARE PRODUCT (including all
component parts, the media and printed materials, any upgrades, this EULA, all software, and all
disks), to the recipient. The recipient must also agree to the terms of this EULA. The Limited
Warranty will also be null and void, and AIPTEK shall then be released from honoring any and all
parts of the Limited Warranty. If the recipient does not agree to the terms of the EULA, then the
HARDWARE PRODUCT cannot be transferred.
Important - Read Carefully!
By attempting to install, successfully
If you do not agree to the terms of this EULA, do not attempt to install or
HARDWARE PRODUCT LICENSE
:
..2..
@n IP Company
Gifts - If this HARDWARE PRODUCT was purchased for someone as a gift, the person purchasing
the HARDWARE PRODUCT may give it to the intended recipient without voiding the Warranty,
provided that the person purchasing the HARDWARE PRODUCT does not attempt to open the
package, attempt to install the HARDWARE PRODUCT, or otherwise use the HARDWARE
PRODUCT.
Decompilation, Disassembly, and Reverse Engineering - You may not decompile, disassemble, or
reverse engineer any and all parts of the HARDWARE PRODUCT, except and only to the extent
that such activity is expressly permitted by applicable law notwithstanding this limitation.
Separation of Components - The HARDWARE PRODUCT is licensed as a single product. Its
component parts and software may not be separated for use on more than one computer.
Rental - You may not lease, lend, or rent any and all parts of the HARDWARE PRODUCT,
including any and all backup copies made.
Refunds - If for any reason you wish to return the HARDWARE PRODUCT, you can seek a refund
from the place of purchase. If you cannot get a refund from the place of purchase, you may not
seek a refund for the HARDWARE PRODUCT from AIPTEK, and you agree to not attempt to seek
a refund for the HARDWARE PRODUCT from AIPTEK.
Technical Support -AIPTEK may provide you with Technical Support ("Tech Support") related to the
HARDWARE PRODUCT. Use of Tech Support, which includes the Warranty Service, is governed
by the AIPTEK policies and programs described in the user manual, in "online" documentation,
and/or in other AIPTEK-provided materials, including this EULA. Any supplemental software code
or pieces of hardware provided to you as part of Tech Support shall be considered part of the
HARDWARE PRODUCT and subject to the terms and conditions of this EULA. With respect to
information you provide to AIPTEK as part of the Tech Support, AIPTEK may use such information
for its business purposes, including but not limited to product support and development. AIPTEK
will not utilize such information in a form that personally identifies you.
Registration - You agree to register the HARDWARE PRODUCT with AIPTEK within 60 days of
purchase of the HARDWARE PRODUCT. As part of this agreement, you agree to provide AIPTEK
with all requested information. All information provided must be accurate and true.
Termination - Without prejudice to any other rights, AIPTEK may terminate this EULA if you fail to
comply with the terms and conditions of this EULA. In such event, you must destroy all copies of
the Changes to the EULA - AIPTEK reserves the right to amend, change, and update this EULA at
any time, and without notice. The user agrees to abide by such amendments, changes, and
updates, should any be made.
For information on the Limited Warranty, please see the "Statement of Limited Warranty".For the
most updated version of the End-User License Agreement or list of Authorized R es ellers, please
visit our webpage at http://www.aiptek.com.
3. COPYRIGHT - All title and copyrights in and to the HARDWARE PRODUCT (including but not
limited to any images, photographs, animations, video, audio, music, text, and "Applets" incorporated
into the HARDWARE PRODUCT), the accompanying printed materials, all "online" documentation,
any copies of the software included with the HARDWARE PRODUCT, all pieces of physical
hardware, all media, and/or other AIPTEK-provided materials, are owned by AIPTEK or its suppliers.
The HARDWARE PRODUCT is protected by copyright laws and international treaty provisions;
..3..
Therefore, you must treat the HARDWARE PRODUCT like any other copyrighted material except that
you may install the HARDWARE PRODUCT only as described in this EULA. You may not copy the
printed materials accompanying the HARDWARE PRODUCT.
4. Other Mediums of Acquisition - You may receive the HARDWARE PRODUCT in more than one
medium. Regardless of the type or size of medium you receive, you may use only one medium that is
appropriate for your single computer. You may not use or install the other medium on another
computer. You may not rent, lease, loan, or otherwise transfer the other medium to another user,
except as part of the permanent transfer (as described in Section 2 of this EULA) of the HARDWARE
PRODUCT.
5. Software Upgrades - AIPTEK may occasionally provide upgrades to the driver program that makes
the HARDWARE PRODUCT function. You are eligible to receive these upgrades provided that you
register the HARDWARE PRODUCT with AIPTEK. Rules for registering the HARDWARE PRODUCT
with AIPTEK are governed by the AIPTEK policies and programs described in the user manual, in
"Online" documentation, and/or in other AIPTEK-provided materials, including this EULA (see Section
2 of this EULA for more information).
6. U.S. GOVERNMENT RESTRICTED RIGHTS - The HARDWARE PRODUCT and documentation
are provided with RESTRICTED RIGHTS. Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and
Computer Software clause at DFARS 252.227-7013 or subparagraphs (c)(1) and (2) of the
Commercial Computer Software Restricted Rights at 48 CFR 52.227-19, as applicable.
is 51 Discovery, Suite 100 Irvine, CA 92618, USA.
AIPTEK, Inc.
7. If you acquired this product in the United States, this EULA is governed by the laws of the State of
California.
8. If this product was acquired outside the United States or its Territories, then local law may apply. If
you live in Canada, any other nations in Central & South America, including the Falkland Islands, or
the United States, its Territories, and its Commonwealths, and you have questions regarding this
EULA, please contact AIPTEK at this address:
92618, USA.
AIPTEK Int'l. Inc. at this address: AIPTEK Int'l. Inc./No. 5-1 Innovation Road I/Science-Based
Industrial Park/Hsin-Chu 300/Taiwan, R.O.C.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL AIPTEK
OR ITS SUPPLIERS BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR
CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES
FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS
INFORMATION, DAMAGE TO COMPUTER SOFTWARE OR HARDWARE, OR ANY OTHER
PECUNIARY LOSS) ARISING OUT OF THE USE OF, INABILITY TO USE THE SOFTWARE
PRODUCT OR THE PROVISION OF, FAILURE TO PROVIDE SUPPORT SERVICES, OR
INABILITY TO INSTALL THE HARDWARE PRODUCT, EVEN IF AIPTEK HAS BEEN ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES. IN ANY CASE, AIPTEK IS RELEASED FROM ALL
LIABILITY. BECAUSE SOME STATES AND JURISDICTIONS DO NOT ALLOW THE EXCLUSION
OR LIMITATION OF LIABILITY, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
If you live in any nation that is not located in the areas as listed above, please contact
AIPTEK, Inc.
51 Discovery, Suite 100 Irvine, CA
Manufacturer
..4..
Contents Checklist
1.PenCam
@n IP Company
2.Application / Driver CD
Driver & Application
3.Install Quick Guide
4.USB Cable
NOTE: If you are missing any of these contents please inform your dealer or
your nearest support office so that the contents can be replaced.
Install Quick Guide
..5..
System Requirements
Microsoft Windows XP/ 98 / ME / 2000
Pentinum 200 MHz (or equivalent) processor or higher
32 MB of RAM (64 MB recommended)
Video card with 2 MB of RAM for minimum 16 bit (High Color) display
4X speed CD-ROM
An available USB port
Specifications
Sensor type
Iamge Performance for Video Stream
9 fps for QVGA(320x240 Pixels)
3 fps for VGA(640x480 Pixels)
Memory & Images
26 Picture for VGA ,
107Pictures for QVGA
Dimension
Battery
Lens view angle
Interface type
Software Support
: Color VGA(640x480)CMOS image sensor
:
(SDRAM 64Mbit):
(640x480 Pixels)
(320x240 Pixels)
:5.6 " x1.35 "x1 "
: AAA1.5V x2 battery
: 54 Degrees
: USB Port
: Microsoft Windows XP/ 98/ME/2000
Operating Environment
The camera should be operated only within the following environmental
conditions:
41-104 Fahrenheit; 5-40 Celsius
20% - 85% relative humidity, non-condensing
PenCam Cautions!
Never immerse any part of the PenCam or its components into any fluid or liquid.
Disconnect the PenCam from your computer before cleaning it.
Remove dust or stains with a soft cloth dampened with water or neutral detergent.
Do not use any volatile chemicals or liquids such as thinner or benzene to clean the
PenCam.
Do not place hot items on the surface of the PenCam.
Do not attempt to disassemble the PenCam.
..6..
@n IP Company
How to Use Your PenCam
Introduction
The camera is capable of taking and storing VGA(640x480 Pixels) images or
QVGA Images. These images may be uploaded to a PC via
(320x240 Pixels)
the USB port.
The camera has two switches on it.
SW1 is the shutter switch.SW2 is the mode switch.
The LCD display is combined with SW2 to show the setting information.
Installing Batteries
User Interface
The PenCam is powered by 2 AAA batteries, or via the USB connector when
attached to a PC.
***Notes ***
When the batteries are unloaded, all of your stored pictures will be
lost.(Battery Capacity: continous snapshot for 2 hours, stand by can
work for approximately 2 weeks)
View Finder
Lens
USB Port
Shutter Switch( )SW1
LCD Display
Mode Switch( )SW2
Battery Cover
..7..
Switching the camera on
Pressing the SW2 when the LCD is blank
will power on the camera. The camera will
automatically power off after 30 seconds
of inactivity. The LCD indicates the
camera mode either "Lr" for low resolution
(QVGA images) or "Hr" for high resolution(VGA images). The LCD then displays
the number of pictures you have
remaining.
Press Sw2
LCD
will be light up
Taking a picture
Press the shutter button to take a picture.
Press Sw1 to take a picture
A high pitched beep indicates that the
picture was taken successfully and the
counter will decrease accordingly. A low
beep indicates insufficient light to take a
picture. A series of beeps is an indication
that the camera is full.
Additional features
Pressing the mode switch repeatedly cycles through additional features as
displayed on the LCD. When a given feature is displayed it may be selected
by pressing the shutter button. If an option is not selected within 5 seconds
the display will revert back to the number of available pictures.
Press SW1 to select mode
Features will be displayed
Press SW2 to change features
..8..
@n IP Company
Self Timer
Pressing the mode button until "St" appears in the LCD then pressing the
shutter button will start a 10 second self-timer. The camera will issue a short
beep every second and then a longer beep. The next beep indicates that the
picture has been taken. Note: The self-timer can not be selected when the
camera is full.
SW1
Switch mode to "St"
"St" will be displayed
Press SW1 to initiate the self-timer mode
Pictures may be taken continuously as long as the shutter button is
Continuous mode
pressed(and the camera is not full) as follows:
Press the mode button until the Ct appears in the LCD. Pressing the shutter
button within 5 seconds will cause the camera to start taking pictures for as
long as the shutter button is held down. If the shutter button is not pressed
within 5 seconds the camera will revert back to normal picture taking. Note:
During the continuous mode the camera will allow pictures to be taken with
incorrect exposure.
SW1
Switch mode to "Ct"
"Ct" will be displayed
Press SW1 to utilize Continuous mode
..9..
Clearing the stored images
Press the mode button until CL appears on the LCD. Pressing the shutter
button once will cause the camera to beep and the CL will start flashing .
Pressing the shutter button again within 5 seconds will clear the camera and
reset the picture counter.
SW1
Switch mode to "CL"
"CL" will be displayed
Press SW1 to select clear mode
LCD will start flashing
Click SW1 twice to clear the memory
Changing the picture resolution
Picture resolution may only be changed when the camera memory is empty.
If any pictures have been taken then the memory must first be cleared. To
change resolution press the mode switch until the resolution option is
displayed, either Hr to change to high resolution mode (if you are currently in
the low resolution mode)or Lr to change to low resolution(if you are currently
in the high resolution mode). The camera will beep and the display will reset
to indicate the number of pictures available.
SW1
.. 10..
Switch mode to "Hr" or "Lr"
"Hr" or "Lr" will be displayed
Press SW1 to change resolution
@n IP Company
How to Upload Photo & Video to PC
Thank you for purchasing the AIPTEK PenCam. This guide will walk you
through the steps of how to install the PenCam onto your computer system.
PenCam Manager Installation
Place the CD into your CD-ROM and click on the PenCam Manager Icon to
begin the installation.If the CD does not automatically display, simply go to
"Start" then "Run" and select the path "D:\Setup.exe". You may need to
replace "D" with the letter that corresponds to your CD-ROM drive.
Now your computer is initializing the Wise Installation Wizard. Please wait.
The welcome screen will appear,
then click "Next".
The CD will begin installing the
driver to the proper location.
The dialog box that appears asks if you
would like to restart your computer now or
later. Press "OK" to complete installation.
.. 11 ..
Start AIPTEK PenCam Manager
Stored pictures may be uploaded to a PC at any time whether or not the
camera is full. Plugging the USB connector into the camera will cause it to
reset. A double beep will sound, but all stored pictures will remain. When the
USB connector is unplugged the camera will switch off. When connected to
the PC the camera may be used as a normal PC camera.
Connect the smaller end of the
USB connector to the side of the
camera.
Plug the other end of
the USB connector
into an available USB
port on your computer.
To start using the PenCam Manager, simply click on the "Start" menu and
go up to "Programs" Then go to the folder named "PenCam" and select it.
This is the program where you can begin to use your camera.
Note:When plugged into
a USB port the camera
gets its power from the
PC. The camera may be
used like this without
any batteries. However,
all pictures will be lost
when the USB connector
is unplugged.
.. 12..
@n IP Company
Mode Selecting
==Press the "Live View" button to switch the camera to PC Camera mode.
=
Press the "DSC Function" button to switch the camera to DSC & Camcorder
=
mode.
Live View (PC Camera Mode)
DSC Function (DSC Mode)
PC Camera Mode
In this mode, it is easy to attach the camera to your system, to use as a stand
PC camera.
the current view is displayed in the "preview" window.
=
Press "Video Source" button to
adjust advanced setings.
=
Press "Video Format" button to set
=
image size.
=
Press "Snap Shot" button to
=
capture an image to album folder.
=
Press "Record button" to recording
=
a video clip to album folder.
.. 13..
DSC Mode
Uploading Photos:
This allows you to upload photos captured by the camera.
Press the "Link" button to link up the camera and upload photo icons.
<
Press the "Folder" button to open the album folder window.
=
Press the "Transfer all" or "Transfer selected" button to transfer photos to
>
the album folder.
=
link up camera for image upload
=
=
Open or Close album folder window
=
=
Transfer selected photos to album folder
=
=
Transfer all photos to album folder
=
.. 14..
@n IP Company
Editing Photos:
It is easy to edit any photo you want in the album folder. Double click the
photo icon to execute your default image application (such as Imaging,
Paint....etc.) to edit your image file.
Uploading Video:
This takes advantage of the continuous mode. It is recommended that this
be displayed in QVGA(low resolution mode). When the camera is full(107
pictures in continuous mode)attach it to the PC via the USB connector and
run the AVI creator. Press the AVI Creator button, and your Images will be
uploaded from the camera then processed into a video clip. ThisAVI file will
be saved in your album folder.
AVI Creator
(Reverse)
AVI Creator
.. 15..
AVI Creator:
Select Images you want to process into a video clip.
<
Press "Setting" button to adjust fram rate.
=
Press "Fram Rate" button to create a AVI file saved in album folder.
>
Playing Video:
You can play any video clip file (AVI format) you want in album folder by
double clicking the AVI file icon to execute your default media application.
this will then play the selected AVI file.
.. 16..
@n IP Company
Image processing:
Click the "Image Process" button to select the image processing function
you want. After pressing "OK" the selected image will be processed using
the checked function.
Image Process
Mail Function:
Click the "Mail" button to attach seleted image files automatically to a new
email document. it is easy to send images to distant family and friends!
.. 17..
Mail
Troubleshooting
Install step missed
camera have to do with the fact that the end-user accidentally skipped a
step during installation. Solution: Uninstall the camera, and reinstall it,
making sure to follow each step of the Quick Install Guide.
- Most of the problems associated with using the
USB ports not enabled in the BIOS
Guide completely, the camera still will not work. Go into the Device
Manager and see if a section called "Imaging Devices" is listed. If this
section does not exist, check the "Sound, Video, and Game Controllers"
section to see if the camera is listed there. If it is, then the problem is that
the USB ports are not enabled in your BIOS. You will need to enter BIOS
and enable them. Then you will need to uninstall and reinstall the camera in
order to use it.
Conflict with another camera driver capture device
other camera installed on your computer, remove the camera and it's driver
completely from your system to avoid a driver conflict with another camera
or capture device.
Ulead Photo Express SE
bundle this software with our cameras. Beyond replacing a CD that may
have a bad copy of the software on it, we cannot help you either learn to
use or troubleshoot each of these pieces of software. Below are the links to
each site that makes these products:
Hours: 8 a.m. to 5 p.m. Pacific Time, Monday through Friday
- AIPTEK contracts with various companies to
Ulead Systems Photo Express SE
http://www.ulead.com/pe/runme.htm
support@ulead.com
Tech Support: 310.523.9399
- Even after following the Quick Install
- If you have any
.. 18..
@n IP Company
Statement of Limited Warranty
AIPTEK, Inc. "AIPTEK" warranties the enclosed device "HARDWARE
PRODUCT" for a period of one year from the date of purchase to be
free from physical, operational, and workmanship defects. AIPTEK also
warrants that the HARDWARE PRODUCT will perform in accordance with
the accompanying written materials during the period that the Limited
Warranty is active. Technical Support provided by AIPTEK shall be available
as described in applicable written materials provided to you by AIPTEK
during the period that the Limited Warranty is active. AIPTEK Technical
Support Representatives will make commercially reasonable efforts to solve
any problems that may arise from the installation and/or use of the
HARDWARE PRODUCT. Some states and jurisdictions do not allow
limitations on duration of an implied warranty, so the above limitation may
not apply to you. To the extent allowed by applicable law, implied warranties
on the HARDWARE PRODUCT, if any, are limited to thirty (30) days.
AIPTEK reserves the right to repair and/or replace defective HARDWARE
PRODUCTS, including the repair and/or replacement of individual defective
components of the HARDWARE PRODUCT, and the repair and/or
replacement of defective disks that contain software from AIPTEK's
suppliers, at its discretion. AIPTEK is the sole entity that will determine
whether or not the HARDWARE PRODUCT, or an individual piece or
components of the HARDWARE PRODUCT, is/are defective. AIPTEK also
reserves the sole right to decide whether or not the HARDWARE
PRODUCT, or piece(s) of the HARDWARE PRODUCT will be repaired or
replaced. This Limited Warranty only covers all components of the
HARDWARE PRODUCT enclosed herein that have been designed and/or
built by AIPTEK, Inc., or AIPTEK Int'l., Inc. AIPTEK does not guarantee any
and all components of this HARDWARE PRODUCT that were not designed,
programmed, and/or built by AIPTEK, Inc. itself, or by AIPTEK Int'l., Inc.
AIPTEK Technical Support is limited to helping the End-User with
installation of the HARDWARE PRODUCT only. AIPTEK Technical Support
.. 19..
will not provide support for software provided by AIPTEK's suppliers that
was included with the HARDWARE PRODUCT, nor will AIPTEK Technical
Support provide assistance and/or training in use of the software provided
by AIPTEK's suppliers.
Any attempt by the end user to disassemble any part of the HARDWARE
PRODUCT, decompile any part of the software included with the
HARDWARE PRODUCT, or damage any piece of the HARDWARE
PRODUCT (including but not limited to accidental damage, incidental
damage, purposeful damage, or damage caused by a person other than the
End-User), shall immediately and irrevocably void the Limited Warranty.
AIPTEK shall then be released from honoring any and all parts of this
Limited Warranty, and the End-User will be ineligible for both the Warranty
Service, and will also be ineligible for receiving Technical Support.
The Limited Warranty cannot be transferred to another individual from the
original purchaser, except as provided in the END-USER LICENSE
AGREEMENT. If the HARDWARE PRODUCT is sold to another user by
the original End-User, the Limited Warranty will be null and void, and
AIPTEK will have no obligation to provide the Warranty Service.
If the HARDWARE PRODUCT is a gift from the original purchaser to
another person, then the Limited Warranty can be transferred to the
recipient of the HARDWARE PRODUCT, provided the original purchaser
does not attempt to open the box which the HARDWARE PRODUCT was
packaged in.
If this HARDWARE PRODUCT is purchased from an unauthorized reseller,
the Limited Warranty will be null and void, and AIPTEK will have no
obligation to provide the Warranty Service. See the "List of Authorized
Resellers" in the manual to determine whether or not you purchased the
HARDWARE PRODUCT from an Authorized Reseller.
Only the End-User who has registered the product and who has kept a copy
of the original receipt may receive the Warranty Service. No other
representatives of the End-User's household, and no other representatives
.. 20..
@n IP Company
of the single entity that purchased the HARDWARE PRODUCT (other than
the End-User in whose name it is registered) can receive or ask for the
Warranty Service.
If the Warranty Service is activated, and AIPTEK has decided to send out
replacement parts for the HARDWARE PRODUCT before receiving the
defective pieces from the End-User, the End-User must send the defective
hardware to AIPTEK within 10 days of receiving the authorization to return
the defective part(s) of the HARDWARE PRODUCT. If the defective parts
are not received within 10 days of the End-User being given authorization to
return the defective part(s) of the HARDWARE PRODUCT, then the Limited
Warranty for the End-User's HARDWARE
PRODUCT shall immediately and irrevocably be voided. AIPTEK shall then
be released from honoring any and all parts of this Limited Warranty, and
the End-User will be ineligible for both the Warranty Service, and will also
be ineligible for receiving Technical Support.
AIPTEK reserves the right to amend, change, and update this Statement of
Limited Warranty at any time without notice. The End-User agrees to abide
by all amendments, changes, and updates made to this Statement of
Limited Warranty.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, AIPTEK
AND ITS SUPPLIERS DISCLAIM ALL OTHER WARRANTIES AND
CONDITIONS, INCLUDING, BUT NOT LIMITED TO, EXPRESSED OR
IMPLIED WARRANTIES, WARRANTIES OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND NONINFRINGEMENT, WITH REGARD TO THE HARDWARE PRODUCT, AND
THE PROVISION OF OR FAILURE TO PROVIDE TECHNICAL SUPPORT.
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU
MAY HAVE OTHERS, WHICH VARY FROM STATE/JURISDICTION TO
STATE/JURISDICTION.
.. 21..
@n IP Company
How To Obtain A Warranty Service
If you believe that you have a defective HARDWARE PRODUCT, call AIPTEK Tech Support. They
will troubleshoot your HARDWARE PRODUCT to find out if it or any piece of the hardware is
defective. If it is, and your HARDWARE PRODUCT is still covered under the Limited Warranty, it will
be repaired or replaced free of charge. You must be registered with AIPTEK in order to obtain the
Warranty Service. If you have not registered, you will be required to register the HARDWARE
PRODUCT with AIPTEK and provide proof of purchase. If you need to contact AIPTEK because you
believe your HARDWARE PRODUCT is defective, you can contact the appropriate office which your
country is assigned to below:
For those who live in the United States, its territories, & its Commonwealths, Canada, & all countries
located in Central & South America, including the Falkland Islands, and all United States citizens
living overseas (including U.S. Government & U.S. Military employees), please contact the office
below:
AIPTEK, Inc.
51 Discovery, Suite 100
Irvine, CA 92618, USA
TEL: 949-585-9600
http://www.AIPTEK.com Hours: 8 a.m. to 5 p.m. Pacific Time
If you live in any country outside of the regions listed above,
Hours: 8 a.m. to 5 p.m. (GMT plus 8 hours)
For the most updated version of the Limited Warranty, or a list ofAuthorized Resellers,
please visit our web page at http://www.AIPTEK.com.tw
FAX: 949-585-9345
Open Monday through Friday
http://www.aiptek.com
AIPTEK International GmbH
HalskestraBe 6
47877 Willich, Germany
TEL +49 21 54 - 92 35 50
Fax +49 21 54 - 92 35 68
http://www.aiptek.de
please contact the office below:
AIPTEK Int'l., Inc.
No. 5-1 Innovation Road I
Science-Based Industrial Park
Hsin-Chu 300
Taiwan, R.O.C.
Tel: 886-3-5678138
Fax: 886-3-5678569
http://www. .com.tw
Open Monday through Friday
aiptek
.. 22.. 82-088-90031 V1.1
Loading...