AiM User Guide
Kit for EVO4, Solo and SoloDL
on Suzuki GSX-R
Release 1.02
1
1
Models and years
This user guide explains how to install AiM Solo and SoloDL on Suzuki GSX-R bikes and how to
connect EVO4 and SoloDL to the Engine Control Unit (ECU) of the bike. Supported models and years
are different for Solo, SoloDL and EVO4.
Brackets for Solo and SoloDL installation are available for the following models/years
• GSX-R1000 2001-2004 and 2009-2014
• GSX-R750 2001-2014
• GSX-R600 2001-2014
EVO4 and SoloDL connecting cable are available for the following model/years:
• GSX-R1000 2005-2014
• GSX-R750 2006-2014
• GSX-R600 2006-2014
Please note: not all combinations are available. With reference to the tables above, no bracket is
available for SoloDL on GSX-R 1000 from 2005 to 2008 included.
2
Kit content and part number
Here follow part numbers of GSX-R installation kit with bracket and ECU interface cable as well as for
ECU interface cables only.
1
2.1
SoloDL kit
SoloDL installation kit is shown here below; part number is: V02569140CS.
The kit includes:
• 1 bracket (1)
• 1 8x45 pan head Allen screw (2)
• 1 toothed washer (3)
• 2 4x10 Allen screws with countersunk head (4)
• 1 rubber loose piece (5)
• 1 AiM interface cable for Suzuki GSX-R (6)
AiM SoloDL bracket kit for Suzuki GSX-R 1000 2009-2014 can also be bought separately as spare part.
Its part number is: X46KSSGSXR.
2
2.2
AiM cable for SoloDL
Suzuki GSX-R cable for SoloDL is shown below; its part number is: V02569140.
Here below cable constructive scheme is showed.
3
2.3
AiM cable for EVO4
Suzuki GSX-R cable for EVO4 is shown below; its part number is: V02563140.
The cable has a built in resistor for K Line signal management. Here below cable constructive scheme
is showed.
4
3
Installation and connection
Here you find the instructions to install Solo and SoloDL and to connect EVO4 and SoloDL to your
Suzuki GSX-R bike ECU. EVO4 cable is long enough to allow installation of the logger under the bike
seat.
3.1
Installation of Solo and SoloDL
As shown here below Suzuki GSX-R bike ignition block can be on the left or on the right of the handle
bar hinge:
5
Fix Solo/SoloDL bracket to the adapter bracket for Suzuki GSX-R using the two countersunk screws
you find in the kit.
Screw the 8x45 pan head Allen screw in the toothed washer and screw the rubber loose piece under
Suzuki adapter bracket.
6
Insert the assembled kit in the handle bar hinge until the distance piece abuts the hinge.
Tighten the central screw on the hinge so that this last grips.
7
Hook Solo/SoloDL to its bracket
Fix it using the screws already inserted rear on Solo/SoloDL bracket.
8
The image here below shows SoloDL correctly installed.
9
3.2
Connection of SoloDL and EVO4 to the bike ECU
To connect EVO4 and SoloDL to the ECU of the bike use the connector you find under the bike seat
shown below.
Uplift the bike seat. ECU connector has a
black rubber cup as shown here on the right.
Remove the black rubber cup as shown here
on the right.
10
Connect AiM wiring to Suzuki wiring as here
on the right.
If you have installed an AiM EVO4 logger
take the cable to the logger.
If you have installed an AiM SoloDL make
the cable pass along the saddle frame as
shown here on the right.
Make the cable pass between the fuel tank
and the chassis as in the image on the right.
Please avoid positions where the cable
would be exposed to direct heat.
11
Connect the cable to SoloDL as here on the
right.
12
4
Configuring with Race Studio 2
Before connecting SoloDL/EVO4 to the ECU set it up as connected to that ECU using Race Studio 2
software.
4.1
Configuring SoloDL
Run the software, press “Device Configuration” on the software left keyboard and select “SoloDL” in
the panel that shows up as below.
13
The software shows SoloDL configuration page: press “Configuration Manager” and select the
configuration you want to use or press “New” to create a new one. In this second case “New
Configuration” panel appears: select ECU Manufacturer “Suzuki” and ECU model “SDS_Protocol” as
shown below.
Confirm pressing “OK” in both panels and transmit the configuration to SoloDL pressing “Transmit” as
shown below.
14
4.2
Configuring EVO4
Run the software, press “Device configuration” on the software left keyboard and select “EVO4” in the
panel that shows up on the right as here below.
15
The software shows EVO4 configuration page: select the configuration you want to use or press “New”
to create a new one. In this second case “New configuration” panel shows up: select ECU Manufacturer
“Suzuki” and ECU model “SDS_Protocol” as shown below.
Confirm pressing “OK” and transmit the configuration to EVO4 pressing “Transmit”.
16
5
Suzuki SDS protocol
Channels received by SoloDL and EVO4 connected to Suzuki “SDS_Protocol” are:
ID CHANNEL NAME FUNCTION
ECU_1 SDS_RPM RPM
ECU_2 SDS_TPS Primary throttle position
ECU_3 SDS_GEAR Engaged gear
ECU_4 SDS_BATT_VOLT Battery Supply
ECU_5 SDS_CLT Engine coolant temperature
ECU_6 SDS_IAT Intake air temperature
ECU_7 SDS_MAP Manifold air pressure
ECU_8 SDS_BAROM Barometric pressure
ECU_9 SDS_BOOST Boost pressure
ECU_10 SDS_AFR Air/Fuel ratio
ECU_11 SDS_NEUT Neutral signal
ECU_12 SDS_CLUT Clutch switch
ECU_13 SDS_FUEL1_pw Fuel injector 1
ECU_14 SDS_FUEL2_pw Fuel injector 2
ECU_15 SDS_FUEL3_pw Fuel injector 3
ECU_16 SDS_FUEL4_pw Fuel injector 4
ECU_17 SDS_MS Mode selector
ECU_18 SDS_XON_ON XON switch
ECU_19 SDS_PAIR Air pressure
ECU_20 SDS_IGN_ANG Ignition angle
ECU_21 SDS_STP Secondary throttle position
17
Loading...