Kit for EVO4, Solo and SoloDL
on Ducati 899,1199 Panigale
Release 1.01
1
Page 2
1
Models and years
This user guide explains how to install AiM Solo and SoloDL on Ducati Panigale bikes and how to
connect EVO4 and SoloDL to the bike Engine Control Unit (ECU). Supported models and years are:
• 899 Panigale from 2013
• 1199 Panigale from 2012
• 1199 Panigale from 2012
• 1199 Panigale S from 2012
• 1199 Panigale Tricolore from 2012
2
Solo/SoloDL kit and EVO4 ECU connection cable
AiM developped an installation kit with bracket and ECU interface cable for Solo/SoloDL and an ECU
interface cable for EVO4.
1
Page 3
2.1
Kit and bracket for Solo/SoloDL on Ducati Panigale
Solo/SoloDL installation kit is shown here below; part number is: V02569170CSP.
The kit includes:
• 1 bracket (1)
• 2 4x10 Allen screws with countersunk head (2)
• 1 washer(3)
• 1 rubber distance piece (4)
• 1 8x45 pan head Allen screw (5)
• 1 AiM ECU interface cable for Ducati Panigale (6)
AiM cable (6) and bracket (1) can also be bought separately as spare parts.
• SoloDL cable for Ducati Panigale: V02569170
• Solo/SoloDL bracket for Ducati Panigale: X46KSTSDP
2
Page 4
2.2
AiM cable for SoloDL
AiM cable for SoloDL on Ducati bikes is shown below; its part number is: V02569170.
The image here below shows the cable constructive scheme
3
Page 5
2.3
AiM cable for EVO4
AiM cable for EVO4 on Ducati bikes is shown below; its part number is: V02563150.
The image here below shows the cable constructive scheme
4
Page 6
3
Installation and connection
Here you find the instructions to install Solo and SoloDL on Ducati Panigale and to connect EVO4 and
SoloDL to the bike ECU. EVO4 cable length allows installation of the logger under the bike seat.
3.1
Installation of Solo and SoloDL
To install Solo/SoloDL on your Ducati bike:
Place the washer and the rubber distance
piece in line with Panigale bracket hole and
insert M8 screw tightening all pieces.
Fix Solo bracket to Panigale one using the
two countersunk screws you find in the kit.
5
Page 7
Insert the assembled brackets in the handle
bar hole.
Tighten the M8 screw and the distance piece
until the assembled brackets about the bike
fork.
Hook Solo to its bracket.
Tighten Solo bracket screws.
6
Page 8
3.2
Connection of SoloDL and EVO4 to the bike ECU
To connect EVO4 and SoloDL to the ECU of the bike use the connector you find under the passenger
seat.
Open the bike tail and remove the connector
cup highlighted in the image here on the
right.
Once the cup has been removed the
connector appears as here on the right.
7
Page 9
Connect AiM wiring to Ducati wiring as here
on the right.
Take the cable to the logger as here on the
right.
To reach SoloDL make the cable pass
between the fuel tank and the bike frame.
Please avoid positions where the cable
would be exposed to direct heat.
8
Page 10
The image here on the right shows the cable
reaching SoloDL.
Connect the cable to SoloDL as here on the
right.
9
Page 11
4
Configuring with Race Studio 2
Before connecting EVO4/SoloDL to the ECU it is necessary to set it via Race Studio 2 software.
4.1
Configuring SoloDL
Run the software, press “Device Configuration” on the software left keyboard and select “SoloDL” in
the panel that shows up as below.
10
Page 12
The software shows SoloDL configuration page: press “Configuration Manager” and select the
configuration you want to use or press “New” to create a new one. In this second case “New
Configuration” panel appears. Select:
• ECU Manufacturer: “DUCATI”
• ECU model: "Panigale"
11
Page 13
Confirm pressing “OK” in both panels and transmit the configuration to SoloDL pressing “Transmit” as
shown below.
4.2
Configuring EVO4
Run the software, press “Device configuration” on the software left keyboard and select “EVO4” in the
panel that shows up on the right as here below.
12
Page 14
The software shows EVO4 configuration page: select the configuration you want to use or press “New”
to create a new one. In this second case “New Configuration” panel appears: select:
• ECU Manufacturer: Ducati
• ECU Model: Panigale
Press “OK” and transmit the configuration to SoloDL pressing “Transmit” as shown below.
13
Page 15
5
Ducati protocols
Channels received by SoloDL and EVO4 connected to Ducati Panigale protocol are:
ID CHANNEL NAME FUNCTION
ECU_1 ECU_RPM RPM
ECU_2 ECU_SPD_REAR Rear wheel speed
ECU_3 ECU_TPS1_ENG Throttle position cylinder 1
ECU_4 ECU_TPS2_ENG Throttle position cylinder 2
ECU_5 ECU_TPS_HAND Manual throttle
ECU_6 ECU_WATER_T Engine coolant temperature
ECU_7 ECU_SPD_FRONT Front wheel speed
ECU_8 ECU_INT_AIR_TEMP Intake air temperature
ECU_9 ECU_BATTERY Battery supply
ECU_10 ECU_BRAKE_SW Brake switch
ECU_11 ECU_CLUTCH_SW Clutch switch
ECU_12 ECU_GEAR Engaged gear
ECU_13 ECU_NEUTRAL_SW Neutral switch
ECU_14 ECU_OILP_SW Oil pressure switch
ECU_15 ECU_TURN_RIGHT Right turn indicator
ECU_16 ECU_TURN_LEFT Left turn indicator
ECU_17 ECU_SW_ENG_MAP Engine map selector
ECU_18 ECU_SW_BEAM High beam switch
ECU_19 ECU_BARO Barometric pressure
ECU_20 ECU_LAMB_H Horizontal cylinder lambda value
ECU_21 ECU_LAMB_TMP_H Horizontal cylinder lambda temperature