Ag Leader GeoSteer OmniSTAR Demodulator Installation Manual

Page 1
200-0653-01 Kit
GeoSteer OmniSTAR Demodulator Kit
Item Component Part Number Qty Notes
1.
2.
3.
4.
5.
6.
7.
Assembly, OmniSTAR Demodulator 200-0634-01 1
Cable, RF OmniSTAR 201-0536-01 1
Washer, Split Lock M6 SS 517-0031-01 2
Screw, Pan-head M6 x 25mm SS 515-0120-01 2
Cable Tie, 5-1/2" x 0.13" Black Nylon
Installation Instructions 602-0304-01 1
510-0078-01 30
OmniSTAR Demodulator Kit Installation Instructions 602-0304-01 Rev A
Page 2
LEGAL DISCLAIMER
The manufacturer disclaims any liability for damage or injury that results from failure to follow the instructions and warnings set forth herein.
Note: The installation procedures must be performed by an authorized, fully trained and certified dealer technician.
Note: Read and follow ALL instructions in this guide carefully before installing any hardware or operating the steering system.
Note: Take careful note of the information in the Safety Information section and throughout this guide.
Special Requirements
Tools
This list consists of the tools required to complete the installation. The installer is assumed to have a complete set of common installation tools.
#1 Phillips screwdriver #3 Phillips screwdriver Cleaning rags
Wire cutter small Ladder, 10 ft (3 m)
Technical Support
Refer to your Display user manual for technical support information.
Contact Information
Refer to your Display user manual for contact information.
Trademark Information
OmniSTAR is a registered trademark of Trimble Navigation Limited.
Copyright © 2012 All Rights Reserved
2 OmniSTAR Demodulator Kit Installation Instructions
Page 3
Safety and Regulatory Requirements
The GeoSteer system installer and manufacturer disclaim any responsibility for damage or physical harm caused by failure to adhere to the following requirements:
• The GeoSteer system must be operated by a trained and qualified operator.
• The operator must never leave the vehicle while the GeoSteer system is engaged.
• The GeoSteer system is not designed to replace the vehicle operator.
Regulatory Information
This device complies with Part 15 of the FCC Rules. This device shall be professionally installed and maintained by a trained technician as directed by FCC regulations. Use of an antenna other than that outlined in the FCC and IC certification filings for each of the radio products may violate FCC regulations. This device operation is subject to the following two conditions:
1. It may not cause harmful interference.
2. It must accept any interference received, including interference that may cause undesired operation.
OmniSTAR Demodulator Kit Installation Instructions 3
Page 4
Overview
The OmniSTAR Demodulator Kit provides a link between the GeoSteer system and the OmniSTAR correction satellite for your region. This manual provides the instructions for installing the OmniSTAR Demodulator Kit onto the GeoDock of the GeoSteer system. Follow the instructions provided to install this kit.
Procedure
1. Turn off the GeoSteer system, disconnect the RF cables
from the GeoDock and remove the GeoDock from the vehicle.
_____________________________________________
Note: The GeoSteer system must always be turned off before connecting or disconnecting cables. ____________________________________________
2. Remove the GeoDock cover by removing the eight Phillips
screws from the bottom of the GeoDock using a #1 Phillips screwdriver
3. Locate cable ties on the bottom of the GeoDock and cut
them using the small wire cutter.
4 OmniSTAR Demodulator Kit Installation Instructions
Page 5
4. Locate the GPS cable (201-0540-01) attached to the front
of the GPS antenna. Unscrew the connector and remove the cable
Note: If necessary, the GPS antenna can be loosened and rotated by loosening the bolt in the center of the GeoDock magnet with a 7/16" wrench.
5. Replace the cable you have just removed with the
OmniSTAR RF cable (201-0536-01) provided with the installation kit.
Note: Hand tighten only. Do not overtighten.
6. Route the OmniSTAR RF cable on the side opposite of the
Cell Modem cable (201-0538-01) and secure both cables with cable ties.
7. Reinstall GeoDock cover removed in Step 1 with the eight
Phillips screws and a #1 Phillips screwdriver.
________________________________________________
Note: To insert the screws on the plastic cover, slowly rotate the screw counterclockwise until the screw thread drops into the existing threads on the cover, then turn the screw clockwise to tighten. Do not over tighten the screws. Do not exceed 10 in-lbs (1.1 Nm) torque.
________________________________________________
8. Attach the OmniSTAR Demodulator Assembly to the
bottom of the GeoDock assembly using two M6 x 25mm screws with two M6 split washers.
9. Tighten the screws with a #3 Philips screwdriver.
OmniSTAR Demodulator Kit Installation Instructions 5
Page 6
10. Attach the OmniSTAR RF cable to the TNC connector on
the OmniSTAR demodulator as shown in photo.
Note: Connector only fits on one side of the OmniSTAR demodulator despite the two ports looking similar. Do not force connector, if connector does not engage, check to see it is the proper port.
Note: Hand tighten only. Do not over tighten.
11. Attach the GeoDock assembly to the GeoDock Mounting
Plate on top of the vehicle.
_______________________________________________ Note: The GeoSteer system must always be turned off before connecting or disconnecting cables. _______________________________________________
Note: If this is the initial GeoSteer install, refer to the GeoSteer installation manual for proper installation procedures.
12. Attach the 7M Coax GPS Cable (201-0516-01) to the rear
of the OmniSTAR Demodulator.
13. Attach the 7M Cell Modem cable (201-0539-02) to the
GeoDock Cell Modem cable (201-0538-01)
Note: Hand tighten only. Do not overtighten.
14. Attach the Power and Data Extension Cable (PN 201-0535-
01) to the rear of the OmniSTAR Demodulator. The connectors have keys and will only engage in the correct orientation. If the connector does not engage, check the orientation. To avoid possible damage, never force the connector.
Note: To disconnect the cable from the radio, press the two side latches on the cable connector and pull away from the radio.
6 OmniSTAR Demodulator Kit Installation Instructions
Page 7
15. Route Power and Data Extension Cable with the GeoSteer
coaxial cables running to the GeoSteer Control Unit.
16. Bundle the cables together every 12” (30cm) using the
cable ties provided. Use a wire cutter to trim.
17. Attach the Power and Data Extension Cable to the
EXPANSION connector of the GeoSteer Main Cable
Harness.
18. Refer to your GeoSteer User Manual for the OmniSTAR
setup instructions.
Note: In order for the OmniSTAR Demodulator to receive a correction signal, a subscription to the OmniSTAR service must be purchased and the Demodulator must be set to the proper frequency for the region it is operating in. Refer to the GeoSteer User Manual for instructions on setting the radio frequency. For region frequencies, see reference table below. For OmniSTAR subscription information, contact your OmniSTAR service representative.
OmniSTAR Demodulator Kit Installation Instructions 7
Page 8
OmniSTAR Frequency Data
Note: Table 1 below is provided for reference only. For further information and latest updates, visit the OmniSTAR website at www.omnistar.com.
Table 1: OmniSTAR Frequency Data
OmniSTAR Satellites and Regional Coverage (as of December 14, 2011)
Coverage Area Satellite Name Frequency Data Rate
Americas Region:
Eastern U.S. MSV-E 1557.845 1200
Central U.S. MSV-C 1557.835 1200
Western U.S. MSV-W 1557.855 1200
North, Central and South America including the Caribbean ASAT 1539.9325 1200
Atlantic Ocean West AORW 1539.9625 600
Europe / Africa Region:
Atlantic Ocean East AORE 1539.9725 600
Europe, Africa & Middle-East ESAT 1539.9125 1200
India, CIS, Middle-East IOR 1539.9325 600
Asia Pacific Region:
Asia PASAT 1539.9225 1200
Australia & Pacific Rim AUSAT 1539.9625 1200
Source: http://www.omnistar.com
8 OmniSTAR Demodulator Kit Installation Instructions
Page 9
LED Diagnostics
The OmniSTAR Demodulator Kit has an onboard LED light that can assist with troubleshooting in the event of a malfunction.
Figure 1 OmniSTAR Demodulator Diagnostic LEDs
Normal Operation
During normal operation, the LED will be illuminated green with an orange LED blinking rapidly (1-2 times/second). If the LED is steady green with only one blink every 4-5 seconds, it means the unit is powered up but is not receiving data from the OmniSTAR satellite. If the unit is not receiving data, verify the OmniSTAR Demodulator is set to the proper frequency for the region of operation. Refer to your GeoSteer user manual for instructions on how to change the frequency as well as Table 1 in this manual and the OmniSTAR website for regional frequencies.
OmniSTAR Demodulator Kit Installation Instructions 9
Loading...