Please read these user instructions carefully.
Above all please observe the safety instructions on the first few pages
ofthese user instructions! Please keep these user instructions for later
reference. Pass them on to any subsequent owner of the appliance.
The warning triangle and/or specific words (Warning!, Caution!,
1
Important!) are used to highlight instructions that are important for
your safety or for the function of the appliance. It is imperative that
these instructions are observed.
0 This symbol or numbered instruction steps lead you step for step
through the operation of the appliance.
Next to this symbol you receive additional information and practical
3
tips on using the appliance.
Tips and instructions for the economical and environmentally conscious
2
use of the appliance are marked with a clover leaf.
In the event of a malfunction, these operating instructions contain
information on how to rectify faults yourself, see the "What to do, if..."
section.
If these instructions are insufficient, please contact your nearest customer service centre.
In the case of technical problems, our customer service organisation is
available to provide you with assistance at any time (you will find
addresses and telephone numbers in the "Customer Service Centres"
section).
In this respect please read the "Service" note on the rear of these user
instructions.
2
Yourdishwasheris fittedwith the new"PULSE WASH"wash system.
3
With this wash system, the motor speed and spray pressure are
varied during the wash programme to improve the cleaning of the
dishes. It is for this reason that the noise level changes during the
wash programme.
nted on paper manufactured with environmentally sound processes.
The safety aspects of AEG electrical appliances comply with accepted
technical standards and the German Appliance Safety Law. Nevertheless, as a manufacturer we consider it our obligation to make you
aware of the following safety information:
Installation, Connection and Placing into Operation
• The dishwasher may only be transported upright.
• Check the dishwasher for transport damage. Do not in any circumstances connect an appliance that is damaged. In the case of damage,
please contact your supplier.
• Prior to placing the appliance in operation, ensure that the nominal
voltage and type of supply on the rating plate match that of the supply where the appliance is to be installed. The fuse rating is also to be
found on the rating plate.
• For information on how to correctly install and connect up your dishwasher, please read the “Installation“ section. Multiway plugs / connectors and extension cables must not be used. This could constitute
a safety hazard.
Child Safety
• Children often do not recognise the hazards associated with the use
of electrical appliances. It is therefore important that you ensure
children are adequately supervised and that you do not allow children to play with the dishwasher – there is a risk that children can
shut themselves inside the appliance (risk of suffocation!).
• Packaging materials (e.g. films, styrofoam) can be dangerous for children. Risk of suffocation! Keep packaging away from children.
• Detergents can cause burns to the eyes, mouth, and throat, or even
cause choking! Please observe the manufacturer's safety instructions
for cleaners and detergents.
• The water in your dishwasher is not suitable for drinking. If there are
still remnants of detergent in the appliance, there is a risk of burns!
• When disposing of the dishwasher: unplug from the mains, cut off
and dispose of the mains cable. Break the door lock so that the door
no longer shuts.
5
Operating Instructions
General Safety
• Repairs to the dishwasher are only to be carried out by qualified service engineers. Improper repairs can give rise to significant hazards for
the user. If your appliance needs repairing, please contact customer
service or your dealer.
• Never place the dishwasher in operation if the mains cable, water
inlet or drain hose is damaged; or the control panel, work top or
plinth area is damaged such that the inside of the appliance is freely
accessible.
• If the mains lead is damaged, or is to be replaced for a longer lead,
the cable (obtainable from AEG customer service) must be changed
by a service engineer authorised by AEG.
• Never unplug the appliance by pulling on the cable, always pull the
plug.
• Additions or modifications to the dishwasher are not permitted for
safety reasons.
• Ensure that the door of the dishwasher is always closed when it is not
being loaded or unloaded. In this way you will avoid anybody tripping
over the open door and hurting themselves.
• Sharp knives and items of cutlery with sharp edges must be placed in
the cutlery tray or in the upper rack.
Correct Use
• Only wash household dishes using the dishwasher. If the appliance is
used for other purposes, or is used incorrectly, the manufacturer cannot accept any liability for any damage caused.
• Prior to use, ensure that the manufacturers of the special salt, detergent, and rinse aid employed specifically permit the usage of their
products in household dishwashers.
• Do not put any solvents in the dishwasher. There is a risk of an explosion!
• The anti-flood system provides dependable protection against damage due to leaks. For this system to function correctly, the following
preconditions must be met:
– The appliance must remain connected to the mains even when it is
switched off.
– The dishwasher must be correctly installed.
– Always shut off the water supply at the tap when the dishwasher is
not to be used for longer periods, e.g. when you are away on holi-
day.
6
Operating Instructions
• Do not sit or stand on the open door, the appliance may tip over.
• In the event of a fault, first close the tap, then switch off the appliance and unplug it from the mains. If the appliance is permanently
wired to the mains: switch off the fuse(s) or unscrew them.
2 Disposal
Disposing of the Packaging Material
Dispose of the dishwasher packaging material correctly. All the packaging materials used are harmless to the environment and can be recycled.
• Plastic parts are marked with standard international abbreviations:
– >PE<for polyethylene, e.g. sheet wrapping material
– >PS<for polystyrene, e.g. padding material (always CFC-free)
– >POM< for polyoxymethylene, e.g. plastic clips
• Cardboard packaging is manufactured from recycled paper and
should be deposited in the waste paper collection for recycling.
Disposal of old appliances
As and when you cease to use your dishwasher, please take it to a recycling centre or to your dealer who will, for a small contribution to the
costs, dispose of it for you.
7
Operating Instructions
2 Economical and Ecological Dishwashing
• Only connect the dishwasher to the hot water supply if your hot
water is not electrically heated.
• Ensure that the water softener is correctly adjusted.
• Do not pre-rinse dishes under running water.
• If you wash a small load, the load sensor calculates the amount of
water necessary and shortens the programme. It is more economical
to always wash with a full load.
• Select the wash programme to suit the nature and degree of the soiling on the dishes.
• Do not use more detergent, special salt or rinse aid than is recommended in these operating instructions and by the manufacturer of
the respective product.
• The dishwasher's interior light is always switched on as long as the
door of the appliance is open. To save energy you should therefore
always close the door of the dishwasher after loading or removing
dishes.
8
Operating Instructions
Appliance Features and Control Panel
Top Spray Arm
Rubber Seal for
Connecting the
Water Feed to
the Middle Spray
Arm
Spray Arms
Container for
Special Salt
Container
for Rinse Aid
Container for
Detergent
Inlet
for Fan
Assisted Drying
Rating Plate
Filters
Interior Lighting
9
Operating Instructions
Control Panel
Signal Tone
Button
AAN/UIT
MARCHE/ARRET
AUTO
65°
AUTO
BIO 50°
Water Softener
Button
INTENSIEF
INTENSIF 70°
NORMAAL
NORMAL 65°
NORMAAL BIO
NORMAL 50°
Control Panel
E-STAND
ECO 50°
QUICK
RAPIDE 40°
VOORSPOELEN
PRELAVAGE
Door
Handle
Air Outlet for Fan
Assisted Drying
MultiDisplay
Set Start
Delay
STARTTIJDKEUZE
DEPART DIFFERE
LOOPTIJD
TEMPS RESTANT
Indicators
VOORSPOELEN
PRELAVAGE
REINIGEN
LAVAGE
SPOELEN
RINCAGE
NASPOELEN
RINCAGE FINAL
DROGEN
SECHAGE
EINDE
FIN
Display for the Individual
Wash Programme Steps
The Control Panel comprises the ON/OFF switch (AAN/UIT;
MARCHE/ARRET) and the programme buttons with LED indicators.
Signal Tone Button: In addition to the wash programme printed on
the front panel, this button can be used to set whether a signal tone is
to indicate that a wash programme is finished.
Water Softener Button: In addition to the wash programme printed
on the front panel, this button can be used to adjust the dishwasher's
water softener.
The Multi-Display can display,
– the hardness setting to which the water softener is set.
– whether the signal tone is switched on or off.
– the start delay that is set.
– how long the current wash programme can be expected to last.
– which fault has occurred on the dishwasher.
The indicators have the following significance:
ZOUT
SEL
GLANSMIDDEL
PDT. DE RINCAGE
WATER
EAU
ZEEF
FILTRE
DEUR
PORTE
SPROEIARM
BRAS
10
SALT (ZOUT; SEL)Refill with special salt
RINSE AID
(GLANSMIDDEL; PDT. DE RINCAGE)
Refill with rinse aid
WATER (WATER; EAU)Open tap
FILTER (ZEFF; FILTRE)Clean the dishwasher's filter system
DOOR (DEUR; PORTE)The dishwasher door is open
SPRAY ARM (SPROEIARM; BRAS)The middle spray arm is jammed
The FILTER indicator (ZEFF; FILTRE) is intended to remind you to check
3
the filters in the dishwasher from time to time and, if necessary, to
clean it. The indicator illuminates at regular intervals, independent of
the amount of soiling of the filters.
Operating Instructions
Prior to using for the first time
Prior to using for the first time, remove all the clips with which the dish
racks are secured for transport.
Then perform the following steps:
0 1. Adjust the water softener
2. Filling with Special Salt for the Water Softener
3. Filling with Rinse Aid
Adjusting the Water Softener
To prevent the build up of scale on dishes and in the dishwasher, the
dishes must be washed with soft, i.e. low lime content water. For this
reason the dishwasher is fitted with a water softener in which tap
water from a hardness of 4 °d (German degree) is softened with the aid
of special salt.
Your water supplier will be able to inform you on the hardness and
3
hardness range of the water in your area.
0 Adjust the water softener to the setting given in the table that corre-
sponds to the hardness of the water in the area where you live. The
water softener can be adjusted in 10 steps.
Water Hardness
1
in°d
) in mmol/l2) Range
41-50
35-40
31-34
27-30
23-26
19-22
15-18
11-141.9-2.5II2H 2
4-100.7-1.8I/II1H 1
under 4under 0.7I
1)(°d) German degree, measure of water hardness
2)(mmol/1) millimol per litre, international unit for the hardness of water
*Factory setting
7.3-9.0
6.3-7.2
5.5-6.2
4.8-5.4
4.1-4.7
3.3-4.0
2.6-3.2
IV
III
Adjust
to Hardness Setting
9
8
7
6
5
4
3*
0
no salt necessary
Indication on the
Multi-Display
H 9
H 8
H 7
H 6
H 5
H 4
H 3
H 0
11
Operating Instructions
0 1. The dishwasher must be switched off.
2. Press the signal tone and water softener buttons simultaneously and
keep them pressed
3. Press the ON/OFF switch. The LED indicators for the signal tone and
water softener buttons flash.
4. Press the softener button again.
The multi-display indicates the hardness setting.
5. Pressing the hardness button increases the hardness setting by 1.
(Exception: Hardness setting 0 follows hardness setting 9).
6. Once the hardness setting is correctly adjusted, press the ON/OFF
switch.
The hardness setting is then saved.
Filling with Special Salt for the Water Softener
Use only special salt intended for dishwashers. Never fill the salt con-
1
tainer with different types of salt (e.g. cooking salt) or detergent. This
would destroy the water softener.
Prior to filling with salt, please check each time that you really do have
a packet of special salt in your hand.
Fill with special salt:
– Before putting the dishwasher into operation for the first time.
– When the indicator lamp for special salt (ZOUT; SEL) lights up on the
control panel.
If the water hardness in your area is less than 4 °d, you do not need to
3
use special salt.
0 1. Open the door, remove the lower
rack.
2. Undo the lid on the salt container by
turning it anticlockwise.
3. Only when using for the first time:
fill the salt container with water.
4. Place the funnel supplied on the
container opening.
Fill the container with special salt
through the funnel; the capacity of
the container is approx. 1.0-1.5 kg
depending on the grain size. Do not
overfill the salt container with special salt.
12
SALE
SALT
SALZ
SEL
Operating Instructions
The water expelled by filling the salt container with special salt runs
3
out of the salt container onto the base of the washing compartment.
This is not a cause for concern, the water will be pumped out at the
start of the next wash programme.
5. Clean any salt remnants on the container opening.
6. Turn the lid clockwise to the stop, otherwise special salt will leak into
the wash water, this could lead to poor wash results. To avoid this run a
rinse programme after filling the salt container with special salt. This
will wash away salt water and any salt crystals that have been spilt.
Depending on the size of the salt grains, it can take several hours for
3
the salt to dissolve in the water and for the SALT indicator (ZOUT; SEL)
to extinguish. The setting of the water softener and thus the consumption of salt are dependent on the hardness of the local water.
13
Operating Instructions
Filling with Rinse Aid
Rinse aid ensures that your dishes gleam and are free from spots, and
that you glasses are clear.
Use only branded rinse aid for dishwashers. Never fill the rinse aid con-
1
tainer with any another substance (e.g. concentrated vinegar). This
would damage the appliance.
Fill with rinse aid:
– Prior to using the dishwasher for the first time
– When the RINSE AID indicator (NASPOELEN; RINCAGE FINAL) on the
control panel is illuminated.
The rinse aid compartment is on the inside of the dishwasher door.
0 1. Open the door.
2. Press the rinse aid compartment
release button with your finger.
3. Fully open the rinse aid compartment
lid.
4. Fill with rinse aid exactly up to the
level marked “max”; this corresponds
to a quantity of approx. 140 ml.
5. Close the lid and press until it locks
into place.
6. Wipe up any spilt rinse aid with a
cloth. Otherwise too much foam will
be formed during the wash.
14
Operating Instructions
Adjusting Rinse Aid Dosing
As the dishes are washed rinse aid is released from the dispenser into
3
the wash water. The dose is factory set at 4, and can be adjusted from
1 to 6. Only change the setting if streaks, milky spots or dried on water
marks are visible on glasses or crockery.
0 1. Open the door of the dishwasher.
2. Press the rinse aid compartment
release button with your finger.
3. Fully open the rinse aid compartment
lid.
4. Set the dose level.
5. Close the lid and press until it locks
into place.
6. If rinse aid has run out, wipe up with
a cloth.
Setting the Signal Tone for the End of the Wash Programme
You can set whether, in addition to the optical indication of the end of
the programme, a signal tone is also to be heard.
0 1. The dishwasher must be switched off.
2. Press the signal tone and water softener buttons simultaneously and
keep them pressed.
3. Press the ON/OFF switch. The LED indicators for the signal tone and
water softener buttons flash.
4. Press the signal tone button again.
The multi-display indicates the current setting:
b0
b1
5. Pressing the signal tone button changes the setting.
6. Once the multi-display indicates the required setting, press the ON/OFF
switch. The setting is then saved.
Signal tone switched off
Signal tone switched on (factory setting)
15
Loading...
+ 33 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.