AEG EFA9673X User Manual

User manual

Manual de instrucciones

Manual de instruções

EFA 9673 - 90673

elcome to the world of Electrelcome to the world of Electr

elcome to the world of Electr

elcome to the world of Electrelcome to the world of Electr

oluxolux

olux

oluxolux

Thank you for choosing a first class product from Electrolux, which hopefully will provide you with lots of pleasure in the future. The Electrolux ambition is to offer a wide variety of quality products that make your life more comfortable. You find some examples on the cover in this manual. Please take a few minutes to study this manual so that you can take advantage of the benefits of your new machine. We promise that it will provide a superior User Experience delivering Ease-of-Mind. Good luck!

electrolux 3electrolux 3

electrolux 3

electrolux 3electrolux 3

electrelectr

electr

electrelectr

oluxolux

olux contents

oluxolux

Contents

Safety warnings ................................ 5

Description of the Appliance ............. 7

Control Panel .................................... 8

Maintenance and Care ................... 11

Special accessories ........................ 16

Something Not Working.................. 16

Installation ...................................... 17

The following symbols are used in this user manual:

Important information concerning your personal safety and information on how to avoid damaging the appliance.

General information and tips.

Environmental information.

Safety warnings

For the userFor the user

For the user

For the userFor the user

• The cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam.

• Always cover lighted elements, to prevent excess heat from damaging the appliance. In the case of oil, gas and coal fired cookers it is essential to avoid open flames.

• Also, when frying, keep the deep frying pan on the cooker top/cooker under careful control.

• The hot oil in the frying pan might ignite due to overheating.

• The risk of self-ignition increases when the oil being used is dirty.

• It is extremely important to note that overheating can cause a fire. Never carry out any flambé cookingNever carry out any flambé cooking

•

Never carry out any flambé cooking

Never carry out any flambé cookingNever carry out any flambé cooking under the hood.under the hood.

under the hood.

under the hood.under the hood. Always disconnect the unit frAlways disconnect the unit fr

•

Always disconnect the unit fr

Always disconnect the unit frAlways disconnect the unit fr power supply beforpower supply befor

power supply befor

power supply beforpower supply befor any work on the hood, includingany work on the hood, including

any work on the hood, including

any work on the hood, includingany work on the hood, including rr

eplacing the light bulbeplacing the light bulb

eplacing the light bulb (take the

eplacing the light bulbeplacing the light bulb

e carrying oute carrying out

e carrying out

e carrying oute carrying out

cartridge fuse out of the fuse holder or switch off the automatic circuit breaker). It is very important to clean the hoodIt is very important to clean the hood

•

It is very important to clean the hood

It is very important to clean the hoodIt is very important to clean the hood and rand r

eplace the filter at theeplace the filter at the

and r

eplace the filter at the

and rand r

eplace the filter at theeplace the filter at the

ecommended intervals. Failurecommended intervals. Failur

ecommended intervals. Failur

ecommended intervals. Failurecommended intervals. Failur

do so could cause grdo so could cause gr

do so could cause gr

do so could cause grdo so could cause gr to build up, rto build up, r

to build up, r

to build up, rto build up, r

esulting in a firesulting in a fir

esulting in a fir

esulting in a firesulting in a fir

ease depositsease deposits

ease deposits

ease depositsease deposits

• The appliance is not intended for use by young children or infirm persons without supervision.

• Older children must be supervised if using the appliance.

om theom the

om the

om theom the

etoeto

eto

etoeto

e hazare hazar

e hazar

e hazare hazar

electroluxelectrolux

electrolux safety warnings

electroluxelectrolux

• Young children should be supervised to ensure that they do not play with the appliance.

••

ARNING -ARNING -

•

ARNING - Ensure that the

••

ARNING -ARNING appliance is switched off before replacing the lamp to avoid the possibility of electric shock.

This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE). By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.

The symbol on the product, or on the documents accompanying the product, indicates that this appliance may not be treated as household waste. Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment. Disposal must be carried out in

d.d.

accordance with local environmental regulations for waste disposal. For more detailed information about treatment, recovery and recycling of this product, please contact your local council, your household waste disposal service or the shop where you purchased the product.

electrelectr

oluxolux

electr

olux safety warnings

electrelectr

oluxolux

For the installerFor the installer

For the installer

For the installerFor the installer

• When used as an extractor unit, the

hood must be fitted with a hose having preferably the same diameter as the outlet hole. Attention:Attention:

Attention: The hose is not supplied

Attention:Attention: and must be purchased separately.

••

When installing the hood, make surWhen installing the hood, make sur

•

When installing the hood, make sur

••

When installing the hood, make surWhen installing the hood, make sur you observe the following minimumyou observe the following minimum

you observe the following minimum

you observe the following minimumyou observe the following minimum distance frdistance fr

distance fr

distance frdistance fr cooking hob/ring surfaces:cooking hob/ring surfaces:

cooking hob/ring surfaces:

cooking hob/ring surfaces:cooking hob/ring surfaces: electric cookerselectric cookers

electric cookers

electric cookerselectric cookers gas cookersgas cookers

gas cookers

gas cookersgas cookers

om the top edge of theom the top edge of the

om the top edge of the

om the top edge of theom the top edge of the

If the instructions for installation for the gas hob specify a greater distance, this must be adhered to.

• The national Standard on fuelburning systems specifies a maximum depression of 0.04 mbar in such rooms.

• The air outlet must not be connected to chimney flues or combustion gas ducts. The air outlet must under no circumstances be connected to ventilation ducts for rooms in which fuel-burning appliances are installed.

• The air outlet installation must comply with the regulations laid down by the relevant local authorities.

• When the unit is used in extraction mode, a sufficiently large ventilation hole must be provided, with dimensions that are approximately the same as the outlet hole.

• National and regional building regulations impose a number of restrictions on using hoods and fuelburning appliances connected to a chimney, such as coal or oil roomheaters and gas fires, in the same room.

500 mm500 mm

500 mm

500 mm500 mm 650 mm650 mm

650 mm

650 mm650 mm

• Hoods can only be used safely with appliances connected to a chimney if the room and/or flat (air/environment combination) is ventilated from outside using a suitable ventilation hole approximately 500-600 cm large to avoid the possibility of a depression being created during operation of the hood.

• If you have any doubts, contact the relevant controlling authority or

building inspector’s office.

• Since the rule for rooms with fuel burning appliances is “outlet hole of the same size as the ventilation hole”, a hole of 500-600 cm2, which is to say a larger hole, could reduce the performance of the extractor hood.

• If the hood is used in its recirculation mode, it will operate simply and safely in the above conditions without the need for any of the aforementioned measures.

• When the hood is used in its extraction mode, the following rules must be followed to obtain optimal operation:

- short and straight outlet hose

- keep bends in outlet hose to a

minimum

- never install the hoses with an

acute angle, they must always follow a gentle curve.

- keep the hose as large as possible

(preferably the same diameter as the outlet hole).

- the length should be no more than:

3 metres with one 90° bend 2 metres with two 90° bends Bends of more than 90° will reduce the efficiency of the hood and reduce the airflow.

• Failure to observe these basic instructions will drastically reduce the performance and increase the noise levels of the extractor hood.

Description of the Appliance

The cooker hood is designed toThe cooker hood is designed to

•

The cooker hood is designed to

The cooker hood is designed toThe cooker hood is designed to extract unpleasant odours frextract unpleasant odours fr

extract unpleasant odours fr

extract unpleasant odours frextract unpleasant odours fr kitchen, it will not extract steam.kitchen, it will not extract steam.

kitchen, it will not extract steam.

kitchen, it will not extract steam.kitchen, it will not extract steam.

• The hood is supplied as an extractor unit and can also be used with a recirculation mode by fitting a charcoal filter. Only for EFOnly for EF

•

Only for EF

Only for EFOnly for EF

A 90673:A 90673:

A 90673: The cooker

A 90673:A 90673: hood is supplied ready for use as a recirculation hood and may be used for extraction by removing the charcoal filters.

Extraction modeExtraction mode

Extraction mode

Extraction modeExtraction mode

• In this mode fumes are extracted to the outside via a

coupling ringcoupling ring

the

coupling ring.

coupling ringcoupling ring

hosehose

hose connected to

hosehose

• In order to obtain the best performance the hose should have a diameter equal to the outlet hole.

om theom the

om the

om theom the

electroluxelectrolux

electrolux description of the appliance

electroluxelectrolux

Coupling ringCoupling ring

Coupling ring

Coupling ringCoupling ring

RecirRecir

culation modeculation mode

Recir

culation mode

RecirRecir

culation modeculation mode

charchar

• The air is filtered through a filterfilter

filter and returned to the kitchen.

filterfilter

char

charchar

coalcoal

coal

coalcoal

• You will need an original charcoal filter for the recirculation mode. (See Special Accessories).

electrelectr

oluxolux

electr

olux control panel

electrelectr

oluxolux

Control Panel

• Best results are obtained by using a low speed for normal conditions and a high speed when odours are more concentrated. Turn the hood on a few minutes before you start cooking. The hood should be left on after cooking for about 15 minutes or until all the odours have disappeared.

• The hood can also be commanded from the control panel or the remote control. (the remote control is a special accessory and is ordered separately).

CorrCorr

ect ventilation:ect ventilation:

•

Corr

ect ventilation: If the cooker

CorrCorr

ect ventilation:ect ventilation: hood is to work correctly there must be an under pressure in the kitchen. It is important to keep the kitchen windows closed and have a window in an adjacent room open.

• The control switches are located on the hood’s front panel

• The cooker hood is fitted with a sensor which, in the event of extreme variations in temperature, switches the appliance on automatically until the temperature of the environment surrounding the hood has been significantly reduced.

electroluxelectrolux

electrolux control panel

electroluxelectrolux

Model EFModel EF

Model EF

Model EFModel EF

1.1.

Light switch, ON/OFF:Light switch, ON/OFF:

Light switch, ON/OFF:press briefly to switch hob lighting on, press and hold

1.1.

Light switch, ON/OFF:Light switch, ON/OFF:

A 9673 - 90673A 9673 - 90673

A 9673 - 90673

A 9673 - 90673A 9673 - 90673

123 456

for more than 2 seconds to switch upper lighting on.

Mains switch, ON/OFFMains switch, ON/OFF

Mains switch, ON/OFF

Mains switch, ON/OFFMains switch, ON/OFF Press for less than 1 1/2 seconds and the cooker hood goes into the " byby

by" position (dot

byby

“a”“a”

“a” on display is illuminated).

“a”“a” Press for more than 1 1/2 seconds and the cooker hood turns OFF, ALL the controls (except the light push button) are disabled (the display is off). Press again for more than 1 1/2 seconds to reset the cooker hood to "stand by".

3.3.

Filters saturation rFilters saturation r

Filters saturation r

3.3.

Filters saturation rFilters saturation r

Start and choice of motor speed 1-2-3-1-2...Start and choice of motor speed 1-2-3-1-2...

Start and choice of motor speed 1-2-3-1-2...

Start and choice of motor speed 1-2-3-1-2...Start and choice of motor speed 1-2-3-1-2...

Intensive speed ON/OFF:Intensive speed ON/OFF:

Intensive speed ON/OFF: The Intensive speed runs for 5 minutes:

Intensive speed ON/OFF:Intensive speed ON/OFF:

eset key:eset key:

eset key: see the relative text on the following pages.

eset key:eset key:

If the hood is on when the Intensive speed is activated, the hood will revert to previous speed after 5 minutes. If the hood is off when the Intensive speed is activated, the hood will automatically turn off after 5 minutes. The letter

P appears on the display and the remaining time (the dot

“b”“b”

“b” on

“b”“b”

display is flashing), if interrupted an acoustic signal is heard.

Self-TSelf-T

imer ON/OFF:imer ON/OFF:

Self-T

imer ON/OFF: times all the speed levels (the dot

Self-TSelf-T

imer ON/OFF:imer ON/OFF:

“a”“a”

“a” on display is

“a”“a” flashing), and then the cooker hood switches off: The self-timer is set as follows: 1stspeed level 20 minutes 2ndspeed level 15 minutes 3rdspeed level 10 minutes The display shows the remaining operation time, at the end of the time an acoustic signal is heard. Depressing the push-button again exits the function.

DisplayDisplay

Display

DisplayDisplay

standstand

stand

standstand

Should the hood or the controls fail to operate: disconnect the power supply for at least 5 seconds. After reconnecting the power supply wait 15 seconds and then check that the cooker hood is now operating correctly.

1010

electrelectr

1010

GrGr

GrGr maintenance indicatormaintenance indicator

maintenance indicator

maintenance indicatormaintenance indicator

oluxolux

electr

olux control panel

electrelectr

oluxolux

ease and charease and char

ease and char

ease and charease and char

coal filtercoal filter

coal filter

coal filtercoal filter

This hood is fitted with a device that indicates when it is necessary to clean the grease filter or the charcoal filter (if the hood is used in the recirculation version with a charcoal filter). On delivery , the hood is not supplied

EFEF

with a charcoal filter(

A 9673 ONLA 9673 ONL

A 9673 ONL

EFEF

A 9673 ONLA 9673 ONL so the saturation indicator will be disabled. If the hood is to be used with a charcoal filter, the saturation indicator light must be enabled as follows: Set in " Press buttons

OFFOFF

OFF" the hood.

OFFOFF

3 and

4 simultaneously

44 and hold them for 3 seconds. At first only the grease filter LED

F will light up,

FF but when the charcoal filter LED lights up the saturation indicator will be enabled. To disable it: Press buttons again simultaneously and hold them for 3 seconds, until the charcoal filter LED goes out.

3and

Grease filter LED (F)

LED

F will start to flash when it is time

FF to clean the grease filter. Cleaning will be necessary after 40 working hours. Always comply with the maintenance instructions for the grease filter.

Charcoal filter LED (C)

The charcoal filter LED

Y)Y)

Y),

Y)Y)

flash when the charcoal filter needs to

C will start to

be replaced. This operation is necessary after approximately 160 working hours.

Resetting the saturation indicator

After cleaning or replacing the filters, press button grease filter LED

LED

C stops flashing.

3 for 3 seconds until the

F or the charcoal filter

Maintenance and Care

x 4

••

BeforBefor

•

••

Air suction panelsAir suction panels

Air suction panels

Air suction panelsAir suction panels

Remove the perimeter air suction panels to access the grease filters. The perimeter air suction panels are attached to the cooker hood by a series of pull them outwards and detach them from the Clean the perimeter air suction panels as often as the grease filters (for more information about gentle cleaning methods, read the paragraph “Cleaning” in the pages that follow).

e performing any maintenance operation, isolate the hood fre performing any maintenance operation, isolate the hood fr

Befor

e performing any maintenance operation, isolate the hood fr

BeforBefor

e performing any maintenance operation, isolate the hood fre performing any maintenance operation, isolate the hood fr

electrical supply by switching ofelectrical supply by switching of

electrical supply by switching of

electrical supply by switching ofelectrical supply by switching of connector fuse.connector fuse.

connector fuse.

connector fuse.connector fuse. Or if the appliance has been connected thrOr if the appliance has been connected thr

Or if the appliance has been connected thr

Or if the appliance has been connected thrOr if the appliance has been connected thr plug must be rplug must be r

plug must be r

plug must be rplug must be r

pinspins

pins and

pinspins

fastening cablefastening cable

fastening cable.

fastening cablefastening cable

emoved fremoved fr

emoved fr

emoved fremoved fr

coupling springscoupling springs

coupling springs;

coupling springscoupling springs

om the socket.om the socket.

om the socket.

om the socket.om the socket.

f at the connector and rf at the connector and r

f at the connector and r

f at the connector and rf at the connector and r

electroluxelectrolux

electrolux maintenance and care

electroluxelectrolux

om theom the

om the

om theom the

emoving theemoving the

emoving the

emoving theemoving the

ough a plug and socket, then theough a plug and socket, then the

ough a plug and socket, then the

ough a plug and socket, then theough a plug and socket, then the

1111

When refitting the perimeter air suction panels, ALWAYS reattach the fastening cables. Make sure the panels are attached to the cooker hood properly (snapfastened).

1212

electrelectr

oluxolux

electr

olux maintenance and care

electrelectr

oluxolux

Metal grMetal gr

Metal gr

Metal grMetal gr

ease filterease filter

ease filter

ease filterease filter

• The purpose of the grease filters is to

absorb grease particles which form during cooking and it

mustmust

must always be

mustmust used, either in the external extraction or internal re-circulation function.

Attention: the metal grease filters must be removed and washed, either by hand or in the dishwasher, every four weeks.

Removing the metal grRemoving the metal gr

Removing the metal gr

Removing the metal grRemoving the metal gr

ease filterease filter

ease filter

ease filterease filter

• Use the spring handle and remove the filter downward.

Hand washingHand washing

Hand washing

Hand washingHand washing

Soak grease filters for about one hour in hot water with a grease-loosening cleaner, then rinse off thoroughly with hot water. Repeat the process if necessary. Refit the grease filters when they are dry.

DishwasherDishwasher

Dishwasher

DishwasherDishwasher

Place grease filters in the dishwasher. Select most powerful washing programme and highest temperature, at least 65°C. Repeat the process. Refit the grease filters when they are dry.

When washing the metal grease filter in the dishwasher a slight discolouration of the filter can occur, this does not have any impact on its performance.

• Clean the inner housing using a hand hot solution only(never use caustic detergents, abrasive powders or brushes).

CharChar

coal filtercoal filter

Char

coal filter

CharChar

coal filtercoal filter

• The charcoal filter should only be used if you want to use the hood in recirculation mode.

• To do this you will need an original charcoal filter (available from your local Service Force Centre). Cleaning/rCleaning/r

•

Cleaning/r

Cleaning/rCleaning/r

eplacing the chareplacing the char

eplacing the char

eplacing the chareplacing the char

coal filtercoal filter

coal filter

coal filtercoal filter

Unlike other charcoal filters, the LONGLIFE charcoal filter can be cleaned and reactivated.

With normal use the filter should be cleaned every second month (when using the hood 2.5 hours per day,on avarage). The best way to clean the filter is in the dishwasher. Use normal detergent and choose the highest temperature (65º C). Wash the filter separately so that no food parts gets stuck on the filter and later causes bad odours. To reactivate the charcoal, the filter should be dried in an oven for 10 minutes with a maximum temperature of 100º C. After approximately three years of use, the charcoal filter should be replaced with a new one, as the odour reduction capacity will be reduced.

electroluxelectrolux

electrolux maintenance and care

electroluxelectrolux

FittingFitting

•

Fitting

FittingFitting Position the carbon filter inside the hood to cover the protection grill of the motor. Fix the filter with 2 lateral knobs. TT

oror

emoveemove

•

emove proceed in the reverse

oror

emoveemove

order.

• Always specify the hood model code number and serial number when ordering replacement filters. This information is shown on the rating plate located on the inside of the unit.

• The charcoal filter can be ordered from your local Service Force Centre.

1313

1414

electrelectr

oluxolux

electr

olux maintenance and care

electrelectr

oluxolux

ningning

ning

ningning

1414

arar

• Failure to observe the instructions on cleaning the unit and changing the filters will cause a fire hazard. You are therefore strongly recommended to follow these instructions.

• The manufacturer declines all responsibility for any damage to the motor or any fire damage linked to inappropriate maintenance or failure to observe the above safety recommendations.

Changing the light bulb(s)Changing the light bulb(s)

Changing the light bulb(s)

Changing the light bulb(s)Changing the light bulb(s)

Disconnect the cooker hood frDisconnect the cooker hood fr

•

Disconnect the cooker hood fr

Disconnect the cooker hood frDisconnect the cooker hood fr the mains supplythe mains supply

the mains supply

the mains supplythe mains supply

••

Prior to touching the light bulbsPrior to touching the light bulbs

•

Prior to touching the light bulbs

••

Prior to touching the light bulbsPrior to touching the light bulbs ensurensur

e they are they ar

ensur

e they ar

ensurensur

e they are they ar

e cooled down.e cooled down.

e cooled down.

e cooled down.e cooled down.

omom

• Replace the old bulb with a new one of the same type.

• If the light does not come on, make sure the bulb has been inserted in correctly before contacting your local Service Force Centre.

20W max20W max

20W max

20W max20W max

GU4-12V-Ø35mm - 30° - Dichroic

Cleaning the hoodCleaning the hood

Cleaning the hood

Cleaning the hoodCleaning the hood

• Clean the outside of the hood using a damp cloth and a solution of water and mild washing up liquid.

• Never use corrosive, abrasive or flammable cleaning products or products containing bleach.

• Never insert pointed objects in the motor’s protective grid.

• Only ever clean the switch panel and filter grill using a damp cloth and mild washing up liquid.

• Clean all the plastic parts with a soft cloth soaked in warm water and neutral soap .

• It is extremely important to clean the unit and change the filters at the recommended intervals. Failure to do so will cause grease deposits to build up that could constitute a fire hazard.

electroluxelectrolux

electrolux maintenance and care

electroluxelectrolux

1515

1616

electrelectr

1616

Special accessoriesSpecial accessories

Special accessories

Special accessoriesSpecial accessories

CharChar

Char

CharChar Remote contrRemote contr

Remote contr

Remote contrRemote contr

oluxolux

electr

olux special accessories

electrelectr

oluxolux

coal filtercoal filter

coal filter Type 967

coal filtercoal filter

olol

ol RM 6940

olol

Something Not Working

If your appliance fails to work properly please carry out the following checks.

SymptomSymptom

Symptom

SymptomSymptom

The cooker hood will not start...

The cooker hood is not working

The cooker hood has switched off during operation...

SolutionSolution

Solution

SolutionSolution

Check that:Check that:

Check that: The hood is connected

Check that:Check that: to the electricity supply. Check that a fan speed has been selected.

Check that:Check that:

Check that: The fan speed is set high

Check that:Check that: enough for the task. The grease filters are clean. The kitchen is adequately vented to allow the entry of fresh air. If set up for recirculation, check that the charcoal filter is still effective. If set up for extraction, check that the ducting and outlets are not blocked.

The safety cut-out device has been tripped. Turn off the hob and then wait for the device to reset. If the hood has been installed below the heights indicated in the installation instructions the motor will cut-out frequently which will damage the hood.

If after all these checks, the problem persists, contact your local Service Centre, quoting the model and serial number. Please note that it will be necessary to provide proof of purchase for any inguarantee service calls. In-guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown.

Installation

electroluxelectrolux

electrolux installation

electroluxelectrolux

1717

echnical Detailsechnical Details

echnical Details

echnical Detailsechnical Details

EFEF

A 9673 (EFA 9673 (EF

A 9673 (EF

EFEF

A 9673 (EFA 9673 (EF

Dimensions (in cm):Dimensions (in cm):

Dimensions (in cm):

Dimensions (in cm):Dimensions (in cm): Height (Extraction mode): 89,5 ÷ 118,5 Height (Recirculation mode): 89,5 ÷ 129,5 Width: 99,8 Depth: 70 Maximum absorbed power:Maximum absorbed power:

Maximum absorbed power:

Maximum absorbed power:Maximum absorbed power:

350 W350 W

350 W

350 W350 W Motor: 250 W Lighting: 5 x 20 W Length of the cable:Length of the cable:

Length of the cable:

Length of the cable:Length of the cable: Electrical connection:Electrical connection:

Electrical connection:

Electrical connection:Electrical connection: Fuse rating:Fuse rating:

Fuse rating:

Fuse rating:Fuse rating:

Mounting accessories includedMounting accessories included

Mounting accessories included

Mounting accessories includedMounting accessories included

150 cm150 cm

150 cm

150 cm150 cm

220-240 V220-240 V

220-240 V

220-240 V220-240 V

5A T5A T

5A T

5A T5A T

1 Allan wrench for torx screws 12 nuts 6 screws6x70mm 6 dowels Ø 10 mm 12 screws4x7mm 58 screws 3.5 x 9.5 1 deflector (with extensions)

A 90673)A 90673)

A 90673)

A 90673)A 90673)

1818

electrelectr

oluxolux

electr

olux installation

electrelectr

oluxolux

Electrical connection (not for UK)

Safety warSafety war

Safety war

Safety warSafety war Before connecting the appliance to the power supply, check that the voltage indicated on the rating plate corresponds to the mains power supply available. Appliances fitted with a plug can be connected to any standard power socket within easy access. Should it be necessary to provide a fixed connection, the hood must only be installed by an electrician authorised by the local electricity board. When installing, an omnipolar disconnector with a distance of at least 3 mm between contacts must be provided. Fixed connection of the appliance must only be carried out by an authorised electrician.

nings for the electriciannings for the electrician

nings for the electrician

nings for the electriciannings for the electrician

GREEN & YELLOW



Electrical connection for UK only

Safety warSafety war

Safety war

Safety warSafety war Connect the hood to the mains supply via a double pole switch which has 3 mm minimum separation between the contacts. The switch must be accessible at all times. The following is valid in the United Kingdom only:

- the wire which is coloured green and yellow must be connected to the terminal which is marked with the letter E or by the earth symbol ( ), or coloured green or green and yellow;

- the wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black, -

- the wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

nings for the electriciannings for the electrician

nings for the electrician

nings for the electriciannings for the electrician

BLUE

5AT





BROWN

CORD CLAMP

InstallationInstallation

Installation

InstallationInstallation

electroluxelectrolux

electrolux installation

electroluxelectrolux

1919

Make surMake sur

Make sur

Make surMake sur carrying out the installation.carrying out the installation.

carrying out the installation.

carrying out the installation.carrying out the installation.

e that the cooker hood is disconnected fre that the cooker hood is disconnected fr

e that the cooker hood is disconnected fr

e that the cooker hood is disconnected fre that the cooker hood is disconnected fr

om the power supply beforom the power supply befor

om the power supply befor

om the power supply beforom the power supply befor

The cooker hood comes with fixing plugs which are suitable for use with most walls/ceilings. Nevertheless, you should ask a qualified technician to assess the suitability of the materials in accordance with the type of wall/ceiling. The wall/ ceiling must be sufficiently sturdy so as to support the weight of the cooker hood.

Remove the perimeter air suction panels and the grease filters.

Before installing the product:

The perforated frame for the cooker hood is supplied prior to installation in parts. The main parts making up the perforated frame are as follows:

• the upper perforated frame

• the perforated frame extension brackets

• the reinforcement brackets 2 are for use on the upper part 1 is for use on the lower part

Description of the upper perforated frame A:Description of the upper perforated frame A:

Description of the upper perforated frame A:

Description of the upper perforated frame A:Description of the upper perforated frame A:

A (x1)

B (x4)

C (x3), of which:

C1 -C1 -

C1 - 1 of which is pre-assembled

C1 -C1 -

C2C2

Point at which the perforated frame is fixed/hooked to the ceiling

Fixing points for extension brackets

Reinforcement brackets

C1C1

Fixing points for the 2 reinforcement brackets

C1C1

2020

electrelectr

oluxolux

electr

olux installation

electrelectr

oluxolux

Description of the rDescription of the r

Description of the r

Description of the rDescription of the r

reinforcement brackets

einforeinfor

cement brackets C1 and C2cement brackets C1 and C2

einfor

cement brackets C1 and C2

einforeinfor

cement brackets C1 and C2cement brackets C1 and C2

C1C1

(upper and intermediate)

reinforcement bracket C2C2

C2 (lower)

C2C2

Description of the extension brackets B:Description of the extension brackets B:

Description of the extension brackets B:

Description of the extension brackets B:Description of the extension brackets B:

Points at which they are fixed to the upper frame

Fixing points for the lower reinforcement bracket

C2C2

Points at which the bracket is fixed to the cooker hood

PrPr

E (mm)= L- 355

eparing the structural supporteparing the structural support

eparing the structural support

PrPr

eparing the structural supporteparing the structural support

Before assembling the perforated frame, calculate the extension it requires. Use the formula given in the adjacent diagram to help you. Make a note of measurement

E in this

EE booklet; it will serve as a reference when you are calculating the length of the exhaust tube.

electroluxelectrolux

electrolux installation

electroluxelectrolux

2121

Measurement

L should respect the

LL minimum permitted distances from the hob, as indicated in the paragraph entitled “Safety warnings – for the installer”.

• Fit the extension brackets

Btothe

BB perforated frame using 4 screws for each, so that the perforated frame can be extended to the calculated

length

2222

electrelectr

oluxolux

electr

olux installation

electrelectr

oluxolux

For perforated frame extensions (please refer to measurement previously):

smaller than 690 mm:smaller than 690 mm:

smaller than 690 mm: this extension requires only one bracket (

smaller than 690 mm:smaller than 690 mm: this is already fixed in place. between 690 mm and 795 mm:between 690 mm and 795 mm:

between 690 mm and 795 mm: fit both

between 690 mm and 795 mm:between 690 mm and 795 mm:

- greater than 800 mm: fit all available reinforcement brackets ( Use 8 screws to fix each reinforcement bracket in place. Note:Note:

Note: One of the two

Note:Note: supplied.

C1C1

C1 brackets is usually already fitted when the appliance is

C1C1

C1 brackets.

C1C1

E calculated

C1C1

C1); generally

C1C1

2xC1+1xC22xC1+1xC2

2xC1+1xC2)

2xC1+1xC22xC1+1xC2

Installing the structural support toInstalling the structural support to

FRONT

6 x Ø 10 + 4 x Ø 6x70

FRONT

E (mm)-180

Installing the structural support to

Installing the structural support toInstalling the structural support to the cooker hoodthe cooker hood

the cooker hood

the cooker hoodthe cooker hood

• Fix the cooker hood to the structural support using 16 screws (4 per bracket).

Installing the structural support toInstalling the structural support to

Installing the structural support to

Installing the structural support toInstalling the structural support to the ceilingthe ceiling

the ceiling

the ceilingthe ceiling

• Place the template on the ceiling directly above the hob (the centre and sides of the template should be aligned with the centre and sides of the hob). Note:Note:

Note: The side displaying the text

Note:Note: “FRONT” corresponds to the side which will house the control panel once installation is complete.

• Make the holes as indicated on the template (6 holes for 6 screw anchors) and partially tighten 4 screws into the screw anchors in the corners (leave approximately 1 cm between the head of the screw and the ceiling).

• Prepare the electrical connection. Ducted version only:Ducted version only:

•

Ducted version only: Install an

Ducted version only:Ducted version only: exhaust tube long enough to reach the outlet ring located above the cooker hood. The tube should be fitted to the ceiling as an exhaust system to expel fumes outside; the visible part should be 180 mm shorter than the structural support (please refer to measurement

E calculated

previously).

electroluxelectrolux

electrolux installation

electroluxelectrolux

2323

2424

X 4!

2 x

Ø6 x 70

electrelectr

2424

oluxolux

electr

olux installation

electrelectr

oluxolux

• Install the structure to the ceiling, onto the 4 pre-tightened screws and

then screw them in firmly.

• Fix it in place using 2 screws.

For the rFor the r

•

For the r

For the rFor the r

ecirecir

culation mode only:culation mode only:

ecir

culation mode only:

ecirecir

culation mode only:culation mode only: assemble the three parts of the deflector (central part + 2 extensions) using 2 screws so that once assembled, the deflector is the same width as the structural support. Fasten the deflector inside the structural support using 4 screws. Fit an exhaust tube to the deflector connection ring. The tube must be 300 mm shorter in length than the structural support (please refer to measurement

E calculated

previously).

• Connect the exhaust tube to the connection ring above the cooker hood.

• Carry out the necessary electrical connection.

Installing the fluesInstalling the flues

P x 3

R x 6

Q x 3

S x 0

Installing the flues

Installing the fluesInstalling the flues

• Fix the nuts in place with the couplings both on the upper internal sections of the flues (P+Q) and on the lower back section of the flues (R).

• Fix the two upper flue sections (P+Q) directly onto the structural support of the cooker hood according to the assembly diagram (see adjacent figure).

For the filter version, the upper sections must be fitted so that the air recirculation slots are facing upwards. If you wish to use the cooker hood as a ducted model, for aesthetic purposes, the upper flue sections can be turned upside down to hide the slots when the lower flue sections are installed.

electroluxelectrolux

electrolux installation

electroluxelectrolux

2525

2626

electrelectr

2626

oluxolux

electr

olux installation

electrelectr

oluxolux

Fix the section in place using 6 screws (3 per side).

• Lift the flues and fix them onto the structural support using 2 screws (1 per side).

• Install the lower back section of the flue (R) by resting it on top of the cooker hood in the correct position (widen it slightly to allow for an easy fit onto the upper flue).

• Install the lower front section of the flue (S) and widen it slightly to allow for an easy fit onto the upper section. Fix the section in place using 6 screws (3 per side).

+ 58 hidden pages