ADTRAN SHDSL V.35 LTU User Manual

TOTAL ACCESS®3000 SHDSL V.35 LTU

DEFAULT PROVISIONING OPTIONS

FRONT PANEL LED INDICATORS

PWR ●● Off No power

● Green Self-test passed and the module is In Service

● Yellow Self-test passed and the module is Out of Service

SHDSL ●● Off SHDSL Loop is Out of Service -- Unassigned

● Green SHDSL Loop is trained

● Red SHDSL Loop is not trained

G.703 ●● Off G.703 port is not configured, Out of Service -- Unassigned, or in alarm

condition

● Green G.703 port configured and no alarms

Nx64k ●● Off Service is not configured or in alarm condition

● Green Service is configured and operating normally

RTS ●● Off Nx64k service not configured or RTS control line is OFF

● Green RTS control line is ON

RLSD ●● Off Nx64k service not configured or RLSD control line is OFF

● Green RLSD control line is ON

TST ●● Off Module is not in loopback or BERT

● Green Local loopback is active, or BERT running with no errors

✷ Blinking Yellow Module is running a BERT with bit errors

● Red BERT running with no pattern sync

ALM ●● Off No alarm condition detected

● Yellow Remote alarm condition detected

● Red Alarm condition detected locally

V.35 PORT PIN ASSIGNMENTS

INTERFACE CONNECTIONS

The G.703 signal is transmitted to the network either via the Total Access 3000 backplane connectors or the two BNC connectors mounted on the faceplate. The G.703 signal and the SHDSL signal use the following backplane amphenol connector Pairs:

■ SHDSL - Pair 2

■ G.703 Tx - Pair 8

■ G.703 Rx- Pair 7

TOTAL ACCESS

3000 SHDSL

V.35 LTU

SHDSL

1182008L5

PWR

SHDSL

G.703

Nx64K

RTS

RLSD

TST

ALM

G.703

N x

6 4 K

C A U T I O N C A U T I O N !

SUBJECT TO ELECTROSTATIC DAMAGE

OR DECREASE IN RELIABILITY.

HANDLING PRECAUTIONS REQUIRED.

JOBAID

61182008L5-22A

0202

■ For a complete Installation and Maintenance faxback: (877) 457-5007, Document #766. Please have your fax number available. ■

V.35 Port

Circuit No. Circuit Name To/From DCE Pinout (A/B)

102 Signal Ground B 103 Transmit Data To P/S 104 Receive Data From R/T 105 Request To Send To C 106 Clear To Send From D 107 Data Set Ready From E 108/2 Data Terminal Ready To H 109 Received Line Signal Detect From F 113 Transmit Signal Element Timing To U/W 114 Transmit Signal Element Timing From Y/AA 115 Receive Signal Element Timing From V/X 140 Remote Loopback To N 141 Local Loopback To L 142 Test Indicator From NN

Provisioning Options Default

Unit Options

Cross-Connect Map All Idle Local Management Disabled, Enabled Enabled LT Mode Clk Source Internal Clock Internal Clock

Nx64 ETC

G.703 RX Clock NTU Auto Provisioning Disabled, Enabled Disabled External Port Alarms Disabled, Enabled Enabled Line Card Service State In Service Out of Service - Unassigned

Out of Service - Maintenance

Out of Service - Unassigned

G.703 Port Service State In Service Out of Service - Unassigned

Out of Service - Maintenance

Out of Service - Unassigned

Nx64K Port Service State In Service Out of Service - Unassigned

Out of Service - Maintenance

Out of Service - Unassigned

SHDSL Options

Rate (Kbps) Enter a new value for N from 3 to 36, 2056 (N=32)

where Rate(Kbps)=(N x 64) + 8: SNR Margin Alarm Threshold(dB) Disabled, Enabled Disabled Loop Attenuation Alarm Threshold (dB) Disabled, Enabled Disabled

Test Options

Loopback Timeout(Min) Disabled, Enabled Disabled BERT Test Pattern All Zeros 2e15-1

All Ones

2e15-1

2e23-1 2e15-1 BERT Test Pattern Polarity Normal, Inverted Normal Nx64K In-band Pattern Detection Disabled, Enabled Disabled

COMPLIANCE

Caution: Up to -200 VDC may be present on telecommunications wiring.

This product is intended for installation in restricted access locations only and in equipment with a Type “B” or “E” enclosure.

Code Input Output

Power Code (PC) F C Telecommunication Code (TC) – X Installation Code (IC) A –

PRICING AND AVAILABILITY 800.827.0807

TECHNICAL SUPPORT 800.726.8663

RETURN FOR REPAIR 256.963.8722

www.adtran.com

61182008L5-22A

TOTAL ACCESS 3000 SHDSL V.35 LTU MENU TREE

1. Unit Information

SHDSL V.35 LTU

Main

SHDSL Version Vendor List Number Vendor Issue Number Vendor Software Version Unit Identification Code (CLEI) Vendor ID Vendor Model Number Vendor Serial Number Manufacture Date PROM Checksum

2. Provisioning

3. Status

4. Test

1. Cross-Connect Map

2. Restore Factory Defaults

3. Local Management

4. LT Mode Clk Source

5. Circuit ID

6. Software Update

7. Change Password

9. Line Card Service State

10. G.703 Port Service State

8. NTU Auto Provisioning

11. External Port Alarms

12. Nx64K Port Service State

1. ISDN-PRA V3

2. G.704 CRC-4 Multiframing

3. G.704 Idle Pattern

4. Customer Spare Bits Insertion

5. Customer Spare Bits Pattern

6. Network Spare Bits Insertion

7. Network Spare Bits Pattern

9. Network E-bit Generation

8. Network RAI Generation

1. Tx Clock Source

2. Tx Clock Polarity

3. RTS (Circuit 105)

4. CTS (Circuit 106)

5. RTS to CTS Delay (ms)

6. DSR (Circuit 107)

7. DTR (Circuit 108/2)

8. RLSD (Circuit 109)

1. Dual Sided

2. Custom Transparent

3. Customer Non-Transparent

4. Network Transparent

5. Network Non-Transparent

6. Off

RAM/ROM Power-on Self Test

1. SHDSL Local Loopback

2. SHDSL Remote Loopback

3. SHDSL BERT

4. G.703 Local Loopback

5. G.703 BERT

6. Nx64K Local Loopback

7. Nx64K BERT

1. LTU SHDSL Port

2. LTU G.703 Port

4. NTU SHDSL Port

3. NTU Nx64k Port

1. LTU

2. NTU

1. Local

2. Remote

1. LTU SHDSL

2. LTU G.703

3. SHDSL PM Thresholds

1. Rate (kbps)

2. SNR Margin Alarm Threshold (dB)

3. Loop Attenuation Alarm Threshold (dB)

5. Performance History

6. Terminal Mode

1. Unit Options

2. SHDSL Options

4. Nx64K Options

3. G.703 Options

5. Test Options

General Status Aggregate Rate (kbps) SNR Margin (dB) (Cur/Min/Max) Loop Attenuation (dB) (Cur/Min/Max) Errored Seconds (ES) Severely Errored Seconds (SES) Unavailable Seconds (UAS) Code Violations Count (CVC) LOSW Seconds (LOSWS) Loopback Status BERT Status Alarms

SHDSL Version Vendor List Number Vendor Issue Number Vendor Software Version Unit Identification Code (CLEI) Vendor ID Vendor Model Number Vendor Serial Number Other Vendor Information

1. Loopback Timeout (Min)

2. BERT Test Pattern Polarity

3. BERT Test Pattern Polarity

4. Nx64K Inband Pattern Detection

5. RL (Circuit 140)

6. LL (Circuit 141)

7. TI (Circuit 142)

Shelf: Slot: 15 Total Access System 12/27/01 10:20Shelf: Slot: 15 Total Access System 12/27/01 10:20 Unacknowledged Alarms: NoneUnacknowledged

Alarms: None

Circuit ID:Circuit

ID:

Local Cross-Connect Map

SHDSL Timeslots G.703 Timeslots

TS0 = 0 TS12 = 0 TS24 = 0 TS0 = 0 TS12 = TS24 =

TS1 = 0 TS13 = 0 TS25 = 0 TS1 = 0 TS13 = TS25 =

TS2 = 0 TS14 = 0 TS26 = 0 TS2 = 0 TS14 = TS26 =

TS3 = 0 TS15 = 0 TS27 = 0 TS3

TS3 = 0 TS15 = 0 TS27 = 0 TS3 = 0 TS15 = TS27 == 0 TS15 = TS27 =

TS4 = 0 TS16 = 0 TS28 = 0 TS4 = 0 TS16 = TS28 =

TS5 = 0 TS17 = 0 TS29 = 0 TS5 = 0 TS17 = TS29 =

TS6 = 0 TS18 = 0 TS30 = 0 TS6 = 0 TS18 = TS30 =

TS7 = 0 TS19 = 0 TS31 = 0 TS7 = 0 TS19 = TS31 =

TS8 = 0 TS20 = 0 TS32 = N/A TS8 = TS20 =

TS9 = 0 TS21 = 0 TS33 = N/A TS9 = TS21 =

TS10 = 0 TS22 = 0 TS34 = N/A TS10 = TS22 =

TS11 = 0 TS23 = 0 TS35 = N/A TS11 = TS23 =TS11 = 0 TS23 = 0 TS35 = N/A TS11 = TS23 =

Timeslot Assignments Commands

0. Idle A. Apply New Map G. Full G.703 Service

1. G.703 C. Cancel Changes

32. G.704 Frame Tab. Select SHDSL or G.703 Timeslots

33. Nx64K Movement Keys: U. Up D. Down L. Left R. Right

G.704 Framing =

WARRANTY

Warranty for Carrier Networks products manufactured by ADTRAN and supplied under Buyer’s order for international use is five (5) years. For a complete copy of ADTRAN’s International Equipment Warranty, document number 60000003#I-3: (877) 457-5007, Document #583.

SHDSL MENU OPTIONS

The Total Access 3000 SHDSL V.35 Menus can be provisioned only through the Total Access 3000 System Controller Unit (SCU), P/N 1181018L1. These options are accessed via the local terminal or remote access via the 10BaseT or TL1 interfaces. Connect a terminal emulator via the RS-232 (DB-9) connector on the faceplate of the SCU. The terminal must be VT100 or compatible and set for 9600 bps, 8 data bits, no parity, 1 stop bit. At the LOGIN screen, enter the account name and system password. Select ACCESS MODULES from the Total Access Menu. Access the desired SHDSL module by selecting the corresponding slot number.

ADTRAN SHDSL V.35 LTU User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual