Adamatic H-2, H-6, H-4, IGT, I-6 User Manual

Heat & Ice

H&I-2, H&I-4, H&I-6, IGT

Operator’s Manual

and

Technical Supplement

Belshaw Bros., Inc.
814 44th Street NW, Suite 103
Auburn, WA 98001 USA
Tel: [phone]
Fax: [phone]
Toll Free (US): 1-800-578-2547
E-mail: [e-mail]
www.belshaw.com

Heat & Ice

H&I-2, H&I-4, H&I-6, IGT

Operator’s Manual

Belshaw Bros., Inc.

814 44

th

Street NW, Suite 103

Auburn, WA 98001 USA

Phone: +-1-206-322-5474 • Fax: +-1-206-322-5425

Email: [e-mail] • http://www.belshaw.com

If you accept the machine from the shipping
company, you are, in effect, saying that the
machine is in good condition, and you must

To transport the H&I to the workstation and
unpack it:

1. Break down the shipping crate.

pay for the machine. Belshaw cannot pay for
shipping damage, because the freight company
has accepted the machine from Belshaw in good
condition, and is responsible for its safe delivery.

3. Remove all the packing materials from the
H&I, including foam, tape, brown paper,
plastic, and white protective coating.

For your protection, inspect the machine to see
that no parts are bent, scratched, or otherwise

IMPORTANT

damaged. If any damage has occurred in
shipping, file a freight claim with the shipping

Keep this manual for future reference.

company immediately.

EQUIPMENT RECORD

Please provide the information below when you correspond with us about your machine.

Purchased by ______________________________________________________________________

Installed by _______________________________________________________________________

Date of installation __________________________ Model number _________________________

Serial number ______________________________________________________________________

011108

MN-1732EN

Belshaw Bros., Inc.

th

814 44

Street NW, Suite 103

Auburn, WA 98001 USA

Phone: +-1-206-322-5474 • Fax: +-1-206-322-5425

Email: [e-mail] • http://www.belshaw.com

Contents

1 Operation 1

Initial setup 1

2 Cleaning 2

Belshaw Bros., Inc. • www.belshaw.com • Phone [phone] • Fax [phone]

H&I All Models OM MN-1731EN iii

Preface

The H&I Heat and Ice is designed for icing
donuts and a variety of baking products quickly
and easily.

It is meant to be used on a flat surface. The
operator must work safely at all times, read this
manual, and follow its instructions and warnings.

The H&I Heat and Ice uses electrical elements to
heat water in its kettle. The machine is available
with the following electrical configurations:

• 120 volts, 1 phase, 50/60 hertz

• 240 volts, 1 phase, 50/60 hertz

To use the H&I Heat and Ice safely, heed the
following warnings:

• Disconnect from power source before

cleaning or repairing.

• Never touch the icing pan once the

machine is on. The pan gets very hot,
which may cause serious burns.

cause people to slip or fall, resulting in
serious injury or loss of life.

• To prevent unintentional startup and

possible fire, unplug the machine if there
is a local power outage. When the
power is restored, it is safe to plug the
machine in again.

• To avoid electrocution, make sure that

all electrical cords are not frayed or
cracked and that they do not pass
through any water.

• Make sure that all electrical cords are

routed so that no one will trip over them.

• Do not overfill the kettle with water.

• Hot water can cause serious burns.

Make sure that the system and the water
are cool before attempting any
adjustment, repair, disassembly, or
cleaning.

• To avoid electrocution or other injury,

unplug the machine before attempting
any adjustment, repair, disassembly, or
cleaning.

• To avoid damaging the machine, never

use force to assemble, disassemble,
operate, clean, or maintain it.

• Be careful never to get water, or other

materials on the floor. If anything does
get spilled on the floor, mop it up
immediately. Materials on the floor can

Belshaw Bros., Inc. • www.belshaw.com • Phone [phone] • Fax [phone]

iv MN-1731EN H&I All Models OM

1 Operation

3. Wash H&I with warm water and a mild

detergent.

4. Sanitize H&I

5. Install one empty icing bowl.

6. Fill kettle with hot water until the empty

icing bowl is floating ½ in. off the cover.

7. Install the remaining bowls, lids and

thermometer to the kettle

8. Plug in H&I

Figure 1. H&I-4

WARNING

Do not operate without proper water level.

This will prevent damage to the heater

element.

WARNING

Do not submerge the heating element or

control box with water.

NOTE

Use hot water to fill the H&I, using cold

water can take up to 8 hours to heat up to

120°F.

9. Turn on power switch.

10. Set thermostat dial for desired icing

temperature.

NOTE

Final setting will vary depending on

desired icing temperature

NOTE

Do not turn H&I off overnight; H&I can

take up to 8 hours to reheat

Initial setup

1. Remove H&I from box.

2. Remove all packing materials.

Belshaw Bros., Inc. • www.belshaw.com • Phone [phone] • Fax [phone]

H&I All Models OM MN-1731EN 1

2 Cleaning

For your safety, observe the following warnings
throughout the entire cleaning process.

WARNING

Thoroughly clean and dry the floor if

glaze, water, or other materials are spilled.

Materials spilled on the floor can cause

serious injury or loss of life

WARNING

To avoid the possibility of shock, unplug

the unit before cleaning

Once per week, clean as explained below.

WARNING

3. Drain water from kettle, using the drain

valve on the back of the machine.

IMPORTANT

To avoid damage to the wire / frame, use
caution when removing and transporting

the wire / frame

4. Clean the H&I with warm water and mild

cleaner.

5. Sanitize the H&I

6. Install one empty icing bowl.

7. Fill kettle with hot water until the empty

icing bowl is floating ½ in off the cover.

8. Return the remaining bowls, lids and

thermometer to the kettle

9. Plug in H&I

To avoid being burned, wait for icing pan

to cool before removing

1. Unplug the unit. Remove any debris from

the work area before disassembling the
H&I.

2. Remove bowls, lid and thermometer and

wash with warm soapy water, rinse and
wipe dry.

Belshaw Bros., Inc. • www.belshaw.com • Phone [phone] • Fax [phone]

2 MN-1731EN H&I All Models OM

10. Turn on power switch.

IMPORTANT

Do not hose down electrical components

Heat & Ice

H&I-2, H&I-4, H&I-6, IGT

Technical Supplement

Belshaw Bros., Inc.

814 44

th

Street NW, Suite 103

Auburn, WA 98001 USA

Phone: +-1-206-322-5474 • Fax: +-1-206-322-5425

Email: [e-mail] • http://www.belshaw.com

If you accept the machine from the shipping
company, you are, in effect, saying that the
machine is in good condition, and you must

To transport the H&I to the workstation and
unpack it:

1. Break down the shipping crate.

pay for the machine. Belshaw cannot pay for
shipping damage, because the freight company
has accepted the machine from Belshaw in good
condition, and is responsible for its safe delivery.

3. Remove all the packing materials from the
H&I, including foam, tape, brown paper,
plastic, and white protective coating.

For your protection, inspect the machine to see
that no parts are bent, scratched, or otherwise

IMPORTANT

damaged. If any damage has occurred in
shipping, file a freight claim with the shipping

Keep this manual for future reference.

company immediately.

EQUIPMENT RECORD

Please provide the information below when you correspond with us about your machine.

Purchased by ______________________________________________________________________

Installed by _______________________________________________________________________

Date of installation __________________________ Model number _________________________

Serial number ______________________________________________________________________

011108

MN-1731EN

Belshaw Bros., Inc.

th

814 44

Street NW, Suite 103

Auburn, WA 98001 USA

Phone: +-1-206-322-5474 • Fax: +-1-206-322-5425

Email: [e-mail] • http://www.belshaw.com

Contents

1 Installation 1
2 Maintenance 2
3 Troubleshooting 3
4 Appendix 4

Parts List Drawing Insert Page Insert

Belshaw Bros., Inc. • www.belshaw.com • Phone [phone] • Fax [phone]

H&I All Models MN-1731EN iii

Preface

The H&I Heat and Ice is designed for icing
donuts and a variety of baking products quickly
and easily.

It is meant to be used on a flat surface. The
operator must work safely at all times, read this
manual, and follow its instructions and warnings.

The H&I Heat and Ice uses electrical elements to
heat water in its kettle. The machine is available
with the following electrical configurations:

• 120 volts, 1 phase, 50/60 hertz

• 240 volts, 1 phase, 50/60 hertz

To use the H&I Heat and Ice safely, heed the
following warnings:

• Disconnect from power source before

cleaning or repairing.

• Never touch the icing pan once the

machine is on. The pan gets very hot,
which may cause serious burns.

get spilled on the floor, mop it up
immediately. Materials on the floor can
cause people to slip or fall, resulting in
serious injury or loss of life.

• To prevent unintentional startup and

possible fire, unplug the machine if there
is a local power outage. When the
power is restored, it is safe to plug the
machine in again.

• To avoid electrocution, make sure that

all electrical cords are not frayed or
cracked and that they do not pass
through any water.

• Make sure that all electrical cords are

routed so that no one will trip over them.

• Do not overfill the kettle with water.

• Hot water can cause serious burns.

Make sure that the system and the water
are cool before attempting any
adjustment, repair, disassembly, or
cleaning.

• To avoid electrocution or other injury,

unplug the machine before attempting
any adjustment, repair, disassembly, or
cleaning.

• To avoid damaging the machine, never

use force to assemble, disassemble,
operate, clean, or maintain it.

• Be careful never to get water, or other

materials on the floor. If anything does

Belshaw Bros., Inc. • www.belshaw.com • Phone [phone] • Fax [phone]

iv MN-1731EN H&I All Models

1 Installation

4. Sanitize H&I

5. Install one empty icing bowl.

6. Fill kettle with hot water until the empty

icing bowl is floating ½ in. off the cover.

7. Install the remaining bowls, lids and

thermometer to the kettle

8. Plug in H&I

NOTE

NOTE: Picture depicts H&I-4 only

WARNING

Do not operate without proper water level.

This will prevent damage to the heater

element.

WARNING

Do not submerge the heating element or

control box with water.

Use hot water to fill the H&I, using cold

water can take up to 8 hours to heat up to

120°F.

9. Turn on power switch.

10. Set thermostat dial for desired icing

temperature.

NOTE

Final setting will vary depending on

desired icing temperature

NOTE

Do not turn H&I off overnight; H&I can

take up to 8 hours to reheat

Initial setup

1. Remove H&I from box.

2. Remove all packing materials.

3. Wash H&I with warm water and a mild

detergent.

Belshaw Bros., Inc. • www.belshaw.com • Phone [phone] • Fax [phone]

H&I All Models MN-1731EN 1

2 Maintenance

There is no maintenance required for the H&I-2, H&I-4, or IGT models.

Belshaw Bros., Inc. • www.belshaw.com • Phone [phone] • Fax [phone]

2 MN-1731EN H&I All Models

3 Troubleshooting

If you have a problem with your H&I that you
cannot solve, call your dealer or another
qualified technician.

If your dealer cannot help you, please call
Belshaw Bros. at [phone]. When you
call, please specify the following:

• The model name of the machine.

• The serial number of the machine.

• The voltages, phase, and cycle of the

machine.

CAUTION

If you perform repairs yourself or have

them performed by anyone other than a

service technician authorized by Belshaw

Bros., you do so at your own risk.

WARNING

Disconnect the machine from the power

source before disassembling, repairing, or

wiring.

Belshaw Bros., Inc. • www.belshaw.com • Phone [phone] • Fax [phone]

H&I All Models MN-1731EN 3

4 Appendix

See Parts List Drawing Insert Page.

Belshaw Bros., Inc. • www.belshaw.com • Phone [phone] • Fax [phone]

4 MN-1731EN H&I All Models