Acu-Rite 9150 User Manual

www.AcuRite.com
Internet Bridge
®
Web Portal & APP
for AcuRite Weather Sensors
model #09150
ACU-LINK INST 010412
Instruction Manual
Contents
12:34 PM
1 Introduction: About the Acu-Link Internet Bridge 2 Getting to Know the Acu-Link Internet Bridge
Section 1: Connect 3 Choosing a location 4 Connecting the cables 7 Prepare the Bridge for Registration
Section 2: Registration - Web site 8 Register online
Section 3: Using the Web site
12 Overview 13 Adding Sources & Managing Sensors 15 Widget Overview 16 Managing Widgets 17 Sensor Settings 18 Charting History 19 Alarms 20 Weather Select Widgets - Forecasting, etc.. 22 Following a Friendʼs Bridge/ Sharing Your Bridge
Section 4: Registration - Mobile APP
26 Register using the mobile APP
Section 5: Using the APP
30 Overview 31 Records 32 Sensor Settings 33 Alarms 34 Dashboard Viewing Mode 36 Forecast
Section 6: Troubleshooting and Information
38 Troubleshooting 43 Contact Us 44 Product Information & Registration 45 Warranty and FCC Information
www.AcuRite.com
(877) 221-1252
Introduction
Whatʼs in the box? (included)
Internet
Bridge
What do I need? (not included)
1. Network router with an available Ethernet port
2. “Always On “Internet connection
3. PC or Smart phone for registration
4. AcuRite weather sensor(s)
How does it work?
AcuRite weather sensors collect and broadcast current conditions such as temperature and wind speed. The Bridge receives weather data from Acu-Link compatible AcuRite weather sensors. The Bridge connects to your existing home internet router via a standard network cable. The information is automatically streamed to the internet to allow you to monitor home weather conditions remotely on a smart phone and PC.
AcuRite Sensor(s)
Ethernet
Cable
AC Power
Adapter
Bridge
FREE APP for
Android and iPhone
FREE WEB SITE
for PC access
Router
1
Connect
Getting to Know the Acu-Link Internet Bridge Choosing a location
The Acu-Link Internet Bridge receives data from sensors via 433mhz wireless radio frequency. Reception range of the signal from sensors can be limited by very thick concrete or metallic walls or materials. Other “noisy” electronic devices
such as TVʼs and microwaves may also interfere with the signal
reception.
To help ensure a successful reception from the AcuRite sensors, choose a suitable location no more than 330 feet from the sensor to place the Bridge. Choose a location free of large stone or concrete surfaces, metallic surfaces, and place at least 3 feet away from other electronic devices.
Connections
Power
Ethernet
Port
Weather Sensor RF Reception antennae
STATUS LIGHT 2
RF Reception
Port
STATUS LIGHT 1
Network Uplink
(bottom)
Register Button
DEVICE I.D. (MAC Address)
A unique ID that is needed to register your bridge online.
Acu-Link Tip
You will need the MAC address number that is printed on the bottom of the
bridge when it comes time to register your bridge online, so write it down and keep it handy!
Acu-Link
Internet
Bridge
Add Additional Sensors
330 feet Maximum
(100 meters)
sensor(s)
C O M P A T I B L E
Look for this logo on products that have sensors that are compatible with your Acu-Link Internet Bridge. Visit the web site for the most up to date complete listing of Acu-Link compatible sensors.
32
Connect
Step 1. Connect the Ethernet cable Step 2. Connect the AC power adaptor
flip-up the
RF Antennae
for best
Connect the Ethernet cable to the Ethernet port on the Acu-Link Internet Bridge
reception
Connect the other end of the Ethernet cable to an open Ethernet port on your network router*
Acu-Link Tip
Acu-Link will work with standard routers, wireless routers, and Ethernet hubs the same, as long as there is an available Ethernet port and an active “always on” internet connection available.
YOUR PRODUCT MUST BE REGISTERED TO RECEIVE WARRANTY SERVICE
PRODUCT REGISTRATION
To receive product updates,
warranty service,
and information, Go to
www.AcuRite.com
Register a Product
54
Connect
Step 3. Wait for the bridge to start up
After connecting the power and Ethernet cable, the Acu-Link Internet Bridge may need up to 30 MINUTES to start up and automatically download the latest software before it can register with the server.
WAIT READY
STATUS
LIGHT 2
STEADY
STATUS
LIGHT 1
BLINKING
After plugging in the AC adapter the bridge will automatically perform the following boot operations:
MAY TAKE
UP TO
30 MINUTES
STATUS
LIGHT 1
BLINKING
STATUS LIGHT 2
BLINKING
BOTH LIGHTS
ALTERNATING
BLINKING
Step 4. Prepare the Bridge for Registration
The Acu-link Internet Bridge will transmit your weather information to the secure AcuRite servers. From there you will be able to view and track this information via the web site or by downloading and using the Acu-Link APP for iPhone and Android smart phones, we will cover that later.
Before you can access all this wonderful information, you must first “make the connection” by registering your bridge.
1. Make sure that BOTH
2. Press AND HOLD the “REGISTER” button on the bottom of the Acu-Link Internet Bridge for 4 SECONDS.
BLINKING
status lights are blinking rapidly.
STATUS LIGHT 1durationStartup Sequence
1
Initial Boot STEADY STEADY
Downloading
2
firmware from Acu-Link server
Re-Booting STEADY STEADY
3
Ready for Use
4
30
seconds
5 to 30
minutes
30
seconds
READY
BLINKING
RAPIDLY
BLINKING
RAPIDLY
STATUS LIGHT 2
BLINKING
RAPIDLY
STEADY
BLINKING
Acu-Link Tip
Press the “REGISTER” button only once during initial installation. DO NOT
PRESS THE REGISTER BUTTON AGAIN AFTER YOUR BRIDGE HAS BEEN SUCCESSFULLY REGISTERED, or you will lose previously stored weather
data and have to register again!
76
Registration - Web site
Register your Acu-Link Bridge Online
Before attempting to register your bridge, make sure that BOTH
The Acu-Link Internet Bridge can be registered using a PC or on your smart phone. We are going to cover the PC registration process first. Note that most newer tablet devices can also be used to register online.
1. On your PC, browse to www.AcuRite.com and click on the “Register Acu-Link Internet Bridge” link in the support menu.
status lights are blinking rapidly.
www. acuri te.c om
3. Enter in your information to create your account. Click “SAVE” to continue.
Click to save settings
The main web site page, or DASHBOARD will now show but will be empty. Your bridge information still needs to
be entered to view your weather.
2. Click “Create Account”
98
Registration - Web site
4. Select “SETUP MY BRIDGE” from the web site drop
down menu in the upper right corner of the web site.
6. Enter your unique DEVICE ID (MAC address) and the geographic location that the Acu-Link Internet Bridge will be operating from.
DEVICE ID
(MAC Address)
Acu-Link Tip
5. Click on the “ + ” button to add your bridge.
My Web Bridges
Acu-Link Tip
The Acu-Link system allows you to add multiple bridges to your account from multiple locations (for example- a bridge at your home and a bridge
at your business or at another property). You would add additional bridges
from this same window by clicking on the “+” button again.
Click to save settings
7. Click “SAVE” to complete the registration process. You
will then be returned to the DASHBOARD page. Widgets will automatically show up on the dashboard. Note that your widgets may display “-- --” values initially or will not show at all, this is normal until data is received.
After a minute or so, press your browserʼs “REFRESH” or
“RELOAD” button to refresh the page.
Acu-Link Tip
The “Name” that you type will appear on the dashboard as the bridge name. It will also appear on the title bar of each widget. This helps to identify multiple bridges and locations, as well as allowing you to personalize your weather.
1110
Using the Web site
Acu-Link.com
B
A
My Dashboard
The dashboard displays all of your widgets for your sensor(s), think of it as your weather home page. From the dashboard you can access and use all of the features of the Acu-Link system.
C
A
Adding Sources and Managing Sensors
For each Acu-Link web bridge there is a “MANAGE SENSORS” window that shows you all the sensors that the bridge is receiving. If you want these sensors to be available in the “My Sources” list, you can add them by clicking the “MANAGE SENSORS” button.
Manage Sensors
1. Click on the “Manage Sensors” button
2. Click the “ + ” button to add a sensor to the dashboard source list
B
My Sources
The sources list will display the available weather widgets
for your bridge. If you are subscribing to a friendʼs bridge, that bridge and itʼs available shared sources will
show up under the “My Sources” list as well.
C
Widgets
Each weather category is given itʼs own “widget” that
will display the latest information as well as the daily and weekly records. Each widget also allows you to chart the data and set alarms for that weather category. Most widgets will also have a “settings” button which allows you to rename the sensor, set sharing and unit preferences (ºC or ºF, etc.)
Manage Sensors
3. Click “SAVE”
4. Sensor data now available
1312
Loading...
+ 16 hidden pages