USB
5
D-Sub
|
|
|
|
|
Y |
|
|
|
R B G |
|
|
|
|
|
|
9 |
6 |
|
RS232 |
|
|
4 |
|
|
|
|
|
||
|
D-Sub |
2 |
|
|
|
|
|
|
|
||
|
8 |
R B G |
|
||
|
|
|
|||
|
7 |
|
|
|
|
|
2 |
|
|
3 |
|
1 |
USB |
D-Sub |
HDTV adapter |
Y |
|
|
|
||||
|
D-Sub |
|
|
|
|
|
USB B |
|
|
|
AUDIO IN |
|
VGA IN 1 |
S-VIDEO |
|
||
|
RS232 |
|
|||
|
VGA OUT |
|
|
AUDIO OUT |
|
|
|
|
|
VIDEO |
|
|
|
|
|
|
|
|
|
VGA IN 2 |
|
|
W |
R |
5
5
AUDIO IN
USB B
RS232 |
VGA IN 1 |
S-VIDEO |
VGA OUT |
|
AUDIO OUT
VIDEO
VGA IN 2
E62405SP
Nota: L’interfaccia del connettore è soggetta alle specifiche del modello
|
|
|
English |
Italiano |
1.Power cord
2.VGA cable
3.VGA to component video/HDTV adapter
4.Composite video cable
5.Audio cable
6.S-Video cable
7.RS232 cable
8.USB cable
9.3 RCA component cable
Note: Connector interface is subject to model's specifications
Connecting to a Computer
1.Ensure the projector and your computer are turned off.
2.Connect one end of the VGA cable to the "VGA IN" connector on the projector; connect the other end to the VGA connector on the computer and tighten the screws.
3.Connect one end of the power cord into the AC power socket on the projector; connect the other end to an electrical outlet.
Powering On the Projector
1.Remove the lens cap.
2.Turn on the projector first and then the computer.
3.Adjust the position, focus and zoom.
4.Run your presentation.
Powering Off the Projector
1.Press the power button twice.
2.Do not remove AC power cord from outlet until the projector fans shut down.
1.Cavo d’alimentazione
2.Cavo VGA
3. Adattatore VGA a video component/ HDTV
4. Cavo video composito
5. Cavo audio
6.Cavo S-Video
7.Cavo RS232
8. Cavo USB
9. 3 cavo componente RCA
Nota: L’interfaccia del connettore è soggetta alle specifiche del
modello
Connessione a un computer
1. Accertarsi che il proiettore e il computer siano spenti.
2. Collegare un'estremità del cavo VGA al connettore "VGA IN" del proiettore; connettere l'altra estremità al connettore VGA del computer e stringere le viti.
3. Collegare una estremità del cavo elettrico nella presa CA del proiettore, collegare l'altra estremità ad una presa elettrica.
Accensione del proiettore
1. Rimuovere il coperchio dell’obiettivo.
2. Accendere prima il proiettore e poi il computer.
3.Regolare la posizione, la messa a fuoco e lo zoom.
4. Eseguire la presentazione.
Accensione del proiettore
1.Premere il pulsante due volte.
2.Non rimuovere il cavo elettrico CA
dalla presa finché il proiettore non si sarà spento.