Acer X112H, D402D, EV-S33H, V31S, AS311 User Guide

Acer Projector

X112H/D402D/EV-S33H/V31S/AS311/

P1120/X1120H/D401D/EV-S32H/

X1120/D401/EV-S32/X122H/D412D/

EV-X33H/V31X/AX312/X122/D412/

EV-X33/V30X/AX302/P1223/D413D/

EV-X34H/X1223/D413/EV-X34/

P1220n/X1220Hn/D411DT/EV-

X32HG/P1220/X1220H/D411D/EV-

X32H/X1220/D411/EV-X32/X132WH/

D422D/EV-W33H/V31W/AW312/

P1320W/X1320WH/D421D/EV-

W32H Series
User's Guide

Copyright © 2014. Acer Incorporated.
All Rights Reserved.

Acer Projector User's Guide
Original Issue: 10/2014

Changes may be made periodically to the information in this publication without obligation
to notify any person of such revisions or changes. Such changes will be incorporated in new
editions of this manual or supplementary documents and publications. This company makes
no representations or warranties, either expressed or implied, with respect to the contents
hereof and specifically disclaims the implied warranties of merchantability or fitness for a
particular purpose.

Record the model number, serial number, purchase date and place of purchase information in
the space provided below. The serial number and model number are recorded on the label
affixed to your projector. All correspondence concerning your unit should include the serial
number, model number and purchase information.

No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronically, mechanically, by photocopy, recording or otherwise,
without the prior written permission of Acer Incorporated.

Model number: _________________________________

Serial number: __________________________________

Date of purchase: _______________________________

Place of purchase: ______________________________

Acer and the Acer logo are registered trademarks of Acer Incorporated. Other companies' product
names or trademarks are used herein for identification purposes only and belong to their respective
companies.

"HDMI™, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC."

Information for your safety and comfort

Read these instructions carefully. Keep this document for future reference.
Follow all warnings and instructions marked on the product.

Turning the product off before cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.

Caution for plug as disconnecting device

Observe the following guidelines when connecting and disconnecting power to
the external power supply unit:

• Install the power supply unit before connecting the power cord to the AC

power outlet.

• Unplug the power cord before removing the power supply unit from the

projector.

• If the system has multiple sources of power, disconnect power from the

system by unplugging all power cords from the power supplies.

Caution for Accessibility

Be sure that the power outlet you plug the power cord into is easily accessible
and located as close to the equipment operator as possible. When you need to
disconnect power to the equipment, be sure to unplug the power cord from the
electrical outlet.

iii

Warnings!

• Do not use this product near water.

• Do not place this product on an unstable cart, stand or table. If the product

falls, it could be seriously damaged.

• Slots and openings are provided for ventilation to ensure reliable

operation of the product and to protect it from overheating. These
openings must not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug or other similar surface.

This product should never be placed near or over a radiator or heat register, or
in a built-in installation unless proper ventilation is provided.

• Never push objects of any kind into this product through cabinet slots as

they may touch dangerous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any kind onto or into
the product.

iv

• To avoid damage of internal components and to prevent battery leakage,

do not place the product on a vibrating surface.

• Never use it under sporting, exercising, or any vibrating environment

which will probably cause unexpected short current or damage rotor
devices, lamp.

Using electrical power

• This product should be operated from the type of power indicated on the

marking label. If you are not sure of the type of power available, consult
your dealer or local power company.

• Do not allow anything to rest on the power cord. Do not locate this

product where people will walk on the cord.

• If an extension cord is used with this product, make sure that the total

ampere rating of the equipment plugged into the extension cord does not
exceed the extension cord ampere rating. Also, make sure that the total
rating of all products plugged into the wall outlet does not exceed the fuse
rating.

• Do not overload a power outlet, strip or receptacle by plugging in too

many devices. The overall system load must not exceed 80% of the branch
circuit rating. If power strips are used, the load should not exceed 80% of
the power strip's input rating.

• This product's AC adapter is equipped with a three-wire grounded plug.

The plug only fits in a grounded power outlet. Make sure the power outlet
is properly grounded before inserting the AC adapter plug. Do not insert
the plug into a non-grounded power outlet. Contact your electrician for
details.

Warning! The grounding pin is a safety feature. Using a power outlet that is
not properly grounded may result in electric shock and/or injury.

Note: The grounding pin also provides good protection from unexpected
noise produced by other nearby electrical devices that may interfere with
the performance of this product.

• Use the product only with the supplied power supply cord set. If you need

to replace the power cord set, make sure that the new power cord meets
the following requirements: detachable type, UL listed/CSA certified, VDE
approved or its equivalent, 4.5 meters (15 feet) maximum length.

Product servicing

Do not attempt to service this product yourself, as opening or removing covers
may expose you to dangerous voltage points or other risks. Refer all servicing to
qualified service personnel.

Unplug this product from the wall outlet and refer servicing to qualified service
personnel when:

• the power cord or plug is damaged, cut or frayed

• liquid was spilled into the product

• the product was exposed to rain or water

• the product has been dropped or the case has been damaged

• the product exhibits a distinct change in performance, indicating a need

for service

• the product does not operate normally after following the operating

instructions

Note: Adjust only those controls that are covered by the operating
instructions, since improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to
restore the product to normal condition.

Warning! For safety reasons, do not use non-compliant parts when adding
or changing components. Consult your reseller for purchase options.

v

Your device and its enhancements may contain small parts. Keep them out of
the reach of small children.

Additional safety information

• Do not look into the projector's lens when the lamp is on. The bright may

hurt your eyes.

• Turn on the projector first and then signal sources

• Do not place the product in following environments:

• Space that is poorly ventilated or confined. At least 50cm clearance from walls
and free flow of air around the projector is necessary.

• Locations where temperatures may become excessively high, such as inside of a
car with all windows rolled up.

• Locations where excessive humidity, dust, or cigarette smoke may contaminate
optical components, shortening the life span and darkening the image.

• Locations near fire alarms.

• Locations with an ambient temperature above 40 ºC/104 ºF.

• Locations where the altitudes are higher than 10000 feet.

• Unplug immediately if there is something wrong with your projector. Do

not operate if smoke, strange noise or odor comes out of your projector. It

vi

might cause fire or electric shock. In this case, unplug immediately and
contact your dealer.

• Do not keep using this product to break or drop it. In this case contact your

dealer for inspection.

• Do not face the projector lens to the sun. It can lead to fire.

• When switching the projector off, suggest to ensure the projector

completes its cooling cycle before disconnecting power.

• Do not frequently turn off the main power abruptly or unplug the

projector during operation. The best way is to wait for the fan to turn off
before turning main power off.

• Do not touch air outlet grille and bottom plate which becomes hot.

• Clean the air filter frequently if have. The temperature inside may rise and

cause damage when the filter/ventilation slots clogged with dirt or dust.

• Do not look into the air outlet grille when projector is operating. It may

hurt your eyes.

• Always open the lens shutter or remove the lens cap when the projector is

on.

• Do not block the projector lens with any object when the projector is

under operation as this could cause the object to become heated and
deformed or even cause a fire. To temporarily turn off the lamp, press HIDE
on the remote control.

• The lamp becomes extremely hot during operation. Allow the projector to

cool for approximately 45 minutes prior to removing the lamp assembly for
replacement.

• Do not operate lamps beyond the rated lamp life. It could cause it to break

on rare occasions.

• Never replace the lamp assembly or any electronic components unless the

projector is unplugged.

• The product will detect the life of the lamp itself. Please be sure to change

the lamp when is showing warning message.

• When changing the lamp, please allow unit to cool down, and follow all

changing instructions.

• Reset the "Lamp Hour Reset" function from the Onscreen display

"Management" menu after replacing the lamp module.

• Do not attempt to disassemble this projector. There are dangerous high

voltages inside which may hurt you. The only user serviceable part is the
lamp which has its own removable cover. Refer servicing only to suitable
qualified professional service personnel.

• Do not stand the projector on end vertically. It may cause the projector to

fall over, causing injury or damage.

• This product is capable of displaying inverted images for ceiling mount

installation. Only use acer ceiling mount kit for mounting the projector
and ensure it is securely installed.

vii

Caution for Listening

To protect your hearing, follow these instructions.

• Increase the volume gradually until you can hear clearly and comfortably.

• Do not increase the volume level after your ears have adjusted.

• Do not listen to music at high volumes for extended periods.

• Do not increase the volume to block out noisy surroundings.

• Decrease the volume if you can't hear people speaking near you.

Disposal instructions

Do not throw this electronic device into the trash when discarding. To minimize
pollution and ensure utmost protection of the global environment, please
recycle. For more information on the Waste from Electrical and Electronics
Equipment (WEEE) regulations, visit
http://www.acer-group.com/public/Sustainability/sustainability01.htm

Mercury advisory

For projectors or electronic products containing an LCD/CRT monitor or display:

“Lamp(s) contain Mercury,
Dispose Properly.”

Lamp(s) inside this product contain mercury and must be recycled or disposed of
according to local, state or federal laws. For more information, contact the
Electronic Industries Alliance at www.eiae.org. For lamp-specific disposal
information, check www.lamprecycle.org

viii

First things first

Usage Notes

Do:

• Turn off the product before cleaning.

• Use a soft cloth moistened with mild detergent to clean the display

housing.

• Disconnect the power plug from AC outlet if the product is not being used

for a long period of time.

Don't:

• Block the slots and openings on the unit provided for ventilation.

• Use abrasive cleaners, waxes or solvents to clean the unit.

• Use under the following conditions:

• In extremely hot, cold or humid environments.

• In areas susceptible to excessive dust and dirt.

• Near any appliance that generates a strong magnetic field.

• Place In direct sunlight.

Precautions

Follow all warnings, precautions and maintenance as recommended in this
user's guide to maximize the life of your unit.

Warning:

• Do not look into the projector's lens when the lamp is on. The bright light may hurt

your eyes.

• To reduce the risk of fire or electric shock, do not expose this product to rain or

moisture.

• Please do not open or disassemble the product as this may cause electric shock.

• When changing the lamp, please allow unit to cool down, and follow all changing

instructions.

• This product will detect the life of the lamp itself. Please be sure to change the lamp

when it shows warning messages.

• Reset the "Lamp Hour Reset" function from the Onscreen display "Management"

menu after replacing the lamp module.

• When switching the projector off, please ensure the projector completes its cooling

cycle before disconnecting power.

• Turn on the projector first and then the signal sources.

• Do not use lens cap when projector is in operation.

• When the lamp reaches the end of its life, it will burn out and may make a loud

popping sound. If this happens, the projector will not turn back on until the lamp
module has been replaced. To replace the lamp, follow the procedures listed under
"Replacing the Lamp".

Information for your safety and comfort iii

First things first viii

Usage Notes viii

Precautions viii

Introduction 1

Product Features 1

Package Overview 2

Projector Overview 3

Projector Outlook 3

Control Panel 4

Remote Control Layout 5

Getting Started 7

Connecting the Projector 7

Turning the Projector On/Off 9

Turning on the Projector 9

Turning the projector off 10

Adjusting the Projected Image 11

Adjusting the Height of Projected Image 11

How to optimize image size and distance 12

How to get a preferred image size by adjusting
distance and zoom 14

Contents

User Controls 16

Installation menu 16

Onscreen Display (OSD) Menus 17

Color 18

Image 20

Setting 22

Management 24

3D 25

Language 25

Appendices 26

Troubleshooting 26

LED & Alarm Definition Listing 30

Cleaning and replacing the dust filters 31

Replacing the Lamp 32

Ceiling Mount Installation 33

Specifications 36

Compatibility modes 39

Regulations and safety notices 44

1

Introduction

Product Features

This product is a single-chip DLP® projector. Outstanding features include:

• DLP

• X112H/D402D/EV-S33H/V31S/AS311/P1120/X1120H/D401D/EV-S32H/X1120/

• Enables projecting 3D content via DLP Link Technology

• Acer ColorBoost technology delivers nature’s true colors for vivid, life-like

• High brightness and contrast ratio

• Versatile display modes (Bright, Presentation, Standard, Video, Game,

• NTSC / PAL / SECAM compatible and HDTV (720p, 1080i, 1080p) supported

• Lower power consumption and economy (ECO) mode extends lamp life

• Acer EcoProjeciton Technology delivers Intelligent power management

• Equipped with HDMI™ connection supporting HDCP

• Advanced digital keystone correction optimizes presentations

• Smart detection delivers quick, intelligent source detection

• Multi-language onscreen display (OSD) menus

• Manual focus projection lens zooms up to 1.1x

• 2X(PC)/1.8X(Video) digital zoom and pan function

• Microsoft

®

technology

D401/EV-S32 series: Native 800 x 600 SVGA resolution
X122H/D412D/EV-X33H/V31X/AX312/X122/D412/EV-X33/V30X/AX302/P1223/
D413D/EV-X34H/X1223/D413/EV-X34/P1220n/X1220Hn/D411DT/EV-X32HG/
P1220/X1220H/D411D/EV-X32H/X1220/D411/EV-X32 series: Native 1024 x
768 XGA resolution
X132WH/D422D/EV-W33H/V31W/AW312/P1320W/X1320WH/D421D/EV­W32H series: Native 1280 x 800 WXGA resolution
Auto/4:3/16:9 aspect ratio supported

images

Education, Movie, Dark Cinema, Sports, User) enable optimum
performance in any situation

approach and physical efficiency improvement

®

Windows® 2000, XP, Vista®, Windows 7, Windows 8,

®

Macintosh

OS compliant

English

Note: Functions vary depending on model definition.

English

2

Package Overview

This projector comes with all the items shown below. Check to make sure your
unit is complete. Contact your dealer immediately if any thing is missing.

Projector Power cord VGA cable

2 x Batteries

(option)

Quick start guide Carrying case

Remote control

Security card User’s guide

(option)

Dust filters

(option)

3

Projector Overview

Projector Outlook

Front / upper side

1

3

8

# Description # Description

1 Control panel 5 Focus ring
2 Power/Source button 6 Projection lens
3 Lamp cover 7 Remote control receiver
4 Zoom lever 8 Tilt adjusting wheels

Rear / Left side

3

2

1

4

6

4

2

5

6

7

<Left side><Rear side>

English

7

3

2

1

4

5

5

4

English

# Description # Description

PC analog signal/HDTV/component

1

video input connector (VGA)
2 RS232 connector 6 HDMI connector
3 Composite video input connector 7 Security bar
4 Mini USB connector

5 Power socket

Note: Functions vary depending on model definition.

Control Panel

2

34

32:(5 /$03

7(03

1

# Icon Function Description

1 POWER Power Indicator LED

See the contents in "Turning the Projector
On/Off" section.

Source Changes the active source, short press the

2 TEMP Temp Indicator LED
3 POWER Power Indicator LED
4 LAMP Lamp Indicator LED

button.

5

Remote Control Layout

1

2

3

4

5

6

7

8

9

10

11

12
13

# Icon Function Description

1 Infrared

2 POWER Refer to the "Turning the Projector On/Off" section.

transmitter

Sends signals to the projector.

14

15

16

17

18

19

20

21

22
23

24
25

English

3 ZOOM Zooms the projector display in or out.

4 Four

5 RATIO To choose the desired aspect ratio.

6 MODE Press "MODE" to select the display mode from Bright,

7 3D Press "3D" to select 3D models.

8 Pre./Rewind No function.

9 KeyPad 0~9 Press "0~9" to input a password in the "Security" OSD.

directional
select keys

Enter/ Play/
Pause

Back/Stop No function.

Next/Fast
forward

Use up, down, left, right buttons to select items or make
adjustments to your selection.

Presentation, Standard, Video, Game, Education and User.

No function.

No function.

English

6

# Icon Function Description

10 VGA Press "VGA" to change source to the VGA connector. This

11 SD/USB A No function.

12 LAN/WiFi No function.

13 HDMI/DVI To change source to HDMI/MHL. (no DVI function)

14 SOURCE Changes the active source.

15 HIDE Momentarily turns off the video. Press "HIDE" to hide the

16 KEYSTONE Adjusts the image to compensate for distortion caused by

17 MENU

connector supports analog RGB, YPbPr (480p/576p/720p/
1080i), YCbCr (480i/576i) and RGBsync.

image, press again to display the image.

tilting the projector (± 40 degrees).

• Press "MENU" to launch the Onscreen display (OSD)

menu, back to the previous step for the OSD menu
operation or exit the OSD menu.

• Confirm your selection of items.

18

19 MEDIA_HOME No function.

20 MEDIA_SETUP No function.

21 VIDEO To change source to COMPOSITE VIDEO.

22 COMPONENT No function.

23 PgUp/PgDn For computer mode only. Use this button to select the next or

24 S-VIDEO To change source to S-Video.

25 USB B For USB control and firmware upgrade.

FREEZE

To pause the screen image.

previous page. This function is only available when USB Ctrl
connector (mini type B) is connected to a computer via a USB
cable.

Note: Functions vary depending on model definition.

7

Getting Started

Connecting the Projector

<Type 1>

DVD player

RS232

HDMI

7

HDTV adapter

3

6

RS232

D-Sub

2

RBG

8

HDMI

USB

Y

5

Video output

Y

English

USB

1

4

RBG

D-Sub

DVD player,

Set-top Box,

HDTV receiver

English

8

<Type 2>

HDTV adapter

3

RS232

6

RS232

Y

D-Sub

5

2

RBG

D-Sub

7

USB

USB

Video output

Y

1

4

RBG

DVD player,

Set-top Box,

HDTV receiver

# Description # Description

1 Power cord 5 Composite video cable

2 VGA cable 6 RS232 cable

3 VGA to component/HDTV adapter 7 USB cable

4 3 RCA component cable 8 HDMI cable

Note: To ensure the projector works well with your computer,
please make sure the timing of the display mode is compatible
with the projector.
Note: Functions vary depending on model definition.
Note: USB cable needs powered extender if the length is over 5 m.

9

Turning the Projector On/Off

Turning on the Projector

1 Ensure that the power cord and signal cable are securely connected. The

Power indicator LED will flash red.

2 Turn on the projector by pressing "Power" button on the control panel or

remote control, and the Power indicator LED will turn blue.

3 Turn on your source (computer, notebook, video player ,etc.). The

projector will detect your source automatically.

• If the screen displays "Lock" and "Source" icons, it means the
projector is locked onto a specific source type and there is no such
type of input signal detected.

• If the screen displays "No Signal", please make sure the signal cables
are securely connected.

• If you connect to multiple sources at the same time, use the "Source"
button on the remote control or direct source key on the remote
control to switch between inputs.

Power button

English

English

10

Turning the projector off

1 To turn the projector off, press and hold the power button. This message

appears: "Please press the power button again to complete the shutdown
process." Press the power button again.

2 The LED power indicator will turn RED and blink rapidly after the projector

is turned off, and the fan(s) will continue to operate for about 2 minutes to
ensure that the system cools properly. (only supported under "Instant
Resume" mode)

3 As long as the power cord remains plugged in, you can press the power

button to turn the projector immediately back on anytime during the 2­minute shutdown process. (only supported under "Instant Resume" mode)

4 Once the system has finished cooling, the LED power indicator will stop

blinking and turn solid red to indicate standby mode.

5 It is now safe to unplug the power cord.

Warning indicators:

• "Projector Overheated. Lamp will automatically turn off soon."
This onscreen message indicates that the projector has overheated.
The lamp with automatically turn off, the projector will automatically
shut down, and the LED temp indicator will turn solid red. Contact
your local dealer or service center.

• "Fan failed. Lamp will automatically turn off soon."
This onscreen message indicates that the fan has failed. The lamp will
automatically turn off, the projector will automatically shut down,
and the LED temp indicator will blink. Contact your local dealer or
service center.

Note: Whenever the projector automatically shuts down and the
LED lamp indicator turns solid red, contact your local reseller or
service center.
Note: Functions vary depending on model definition.

11

Adjusting the Projected Image

Adjusting the Height of Projected Image

The projector is equipped with elevator feet for adjusting the height of image.

To raise/lower the image:

Use Tilt adjusting wheel to fine-tune the display angle.

Tilt adjusting wheel

English

12

45"
5"

How to optimize image size and distance

English

Consult the table below to find the optimal image sizes achievable when the
projector is positioned at a desired distance from the screen.

• SVGA/XGA series

If the projector is 2.0 m from the screen, good image quality is possible for
image sizes between 45" and 50".

Note: Remind as below figure, the space of 99 cm height is
required when located at 2.0 m distance.

M

a

x

s

c

r

e

e

n

s

i

z

e

M

i

n

s

c

r

e

e

n

s

i

z

e

A

2.0 m
Desired Distance

Desired

Distance

(m)

<A>

1.5 34 69 x 52 67 38 77 x 57 75

2 45 92 x 69 89 50 102 x 77 99

2.5 56 115 x 86 112 63 128 x 96 124

3 68 138 x 103 134 75 153 x 115 149

3.5 79 161 x 120 157 88 179 x 134 174

4 90 183 x 138 179 100 204 x 153 199

4.5 102 206 x 155 201 113 230 x 172 224

5 113 229 x 172 224 126 255 x 191 249

6 135 275 x 206 268 151 306 x 230 298

7 158 321 x 241 313 176 357 x 268 348

8 181 367 x 275 358 201 408 x 306 398

9 203 413 x 310 403 226 459x 344 448

10 226 459 x 344 447 251 510 x 383 497

Zoom Ratio: 1.1x

Screen size

Diagonal

(inch)

<B>

(Min zoom) (Max zoom)

W (cm) x H

(cm)

Top

From base to top

of image (cm)

<C>

Diagonal

45"

Screen size

(inch)

<B>

50"

B

Height:
89 cm

C

W (cm) x H

Height: 99 cm
from base to top
of image

From base to top

(cm)

Top

of image (cm)

<C>

13

52"
2"

• WXGA series

If the projector is 2.0 m from the screen, good image quality is possible for
image sizes between 52" and 62".

Note: Remind as below figure, the space of 108 cm height is
required when located at 2.0 m distance.

M

a

x

s

c

r

e

e

n

s

i

z

e

M

i

n

s

c

r

e

e

n

s

i

z

e

A

2.0 m
Desired Distance

Desired

Distance

(m)

<A>

1.5 39 83 x 52 68 46 100 x 63 81

2 52 111 x 69 90 62 133 x 83 108

2.5 64 139 x 87 113 77 167 x 104 135

3 77 167 x 104 135 93 200 x 125 163

3.5 90 194 x 122 158 108 233x 146 190

4 103 222 x 139 181 124 267 x 167 217

4.5 116 250 x 156 203 139 300 x 188 244

5 129 278 x 174 226 155 333 x 208 271

6 155 333 x 208 271 186 400 x 250 325

7 181 389 x 243 316 217 467 x 292 379

8 206 444 x 278 361 248 533 x 333 433

9 232 500 x 313 406 279 600 x 375 488

10 258 556 x 347 451 310 667 x 417 542

Zoom Ratio: 1.2x

Screen size Top Screen size Top

Diagonal

(inch)

<B>

(Min zoom) (Max zoom)

W (cm) x H (cm)

From base

to top of

image (cm)

<C>

Diagonal

(inch)

<B>

52"

62"

B

Height:
90 cm

C

W (cm) x H (cm)

Height: 108 cm
from base to
top of image

From base to
top of image

(cm)
<C>

English

English

14

How to get a preferred image size by adjusting
distance and zoom

The table below shows how to achieve a desired image size by adjusting either
the position or the zoom ring.

• SVGA/XGA series

To obtain an image size of 50" set the projector at a distance 2.0 m and 2.2 m
from the screen.

A

50"

Desired image
size

D

Height: 99 cm

from base to top
of image

2.0 m

2.2 m

C

Desired Image Size Distance (m) Top (cm)

Diagonal (inch)

<A>

30 61 x 46 1.2 1.3 59
40 81 x 61 1.6 1.8 79
50 102 x 76 2.0 2.2 99
60 122 x 91 2.4 2.7 119
70 142 x 107 2.8 3.1 139
80 163 x 122 3.2 3.5 158

90 183 x 137 3.6 4.0 178
100 203 x 152 4.0 4.4 198
120 244 x 183 4.8 5.3 238
150 305 x 229 6.0 6.6 297
180 366 x 274 7.2 8.0 357
200 406 x 305 8.0 8.9 396
250 508 x 381 10.0 11.1 495
300 610 x 457 11.9 594

Zoom Ratio: 1.1x

W (cm) x H (cm)

B

Desired Distance

Max zoom

<B>

Min zoom

<C>

From base to top of

image

<D>

15

• WXGA series

To obtain an image size of 60" set the projector at a distance 1.9 m and 2.3 m
from the screen.

A

60"

Desired
image size

D

Height: 105 cm

from base to top
of image

1.9 m

2.3 m

C

Desired Image Size Distance (m) Top (cm)

Diagonal (inch)

<A>

30 65 x 40 1.0 1.2 53

40 86 x 54 1.3 1.6 70

50 108 x 67 1.6 1.9 88

60 129 x 81 1.9 2.3 105

70 151 x 94 2.3 2.7 123

80 172 x 108 2.6 3.1 140

90 194 x 121 2.9 3.5 158

100 215 x 135 3.2 3.9 175

120 258 x 162 3.9 4.7 210

150 323 x 202 4.8 5.8 263

180 388 x 242 5.8 7.0 315

200 431 x 269 6.5 7.8 350

250 538 x 337 8.1 9.7 438

300 646 x 404 9.7 525

Zoom Ratio: 1.2x

W (cm) x H (cm)

B

Desired Distance

Max zoom

<B>

Min zoom

<C>

From base to top of

image

<D>

English

16

User Controls

English

Installation menu

The installation menu provides an onscreen display (OSD) for projector
installation and maintenance. Use the OSD only when the message "No signal
input" is displayed on the screen.

The menu options include settings and adjustments for screen size and distance,
focus, keystone correction and more .

1 Turn on the projector by pressing "Power" button on the control pad.

2 Press the "MENU" button to launch the OSD for projector installation and

maintenance.

Installation

Projection Mode

Projection Location
Auto Keystone
Manual Keystone
Language

Reset

Select

3 The background pattern acts as a guide to adjusting the calibration and

alignment settings, such as screen size and distance, focus and more .

4 The Installation menu includes the following options:

•Projection Mode

•Projection Location

•Auto Keystone settings

•Manual Keystone settings

•Language settings

•Reset to factory default function

Use the up and down arrow keys to select an option, the left and right
arrow keys to adjust selected option settings, and the right arrow key to
enter a submenu for feature setting. The new settings will be saved
automatically upon exiting the menu.

5 Push the MENU button anytime to exit the menu and return to the Acer

welcome screen.

Off

English
Press

Adjust

Exit

Note: Functions vary depending on model definition.

17

Onscreen Display (OSD) Menus

The projector has multilingual OSD that allow you to make image adjustments
and change a variety of settings.

Using the OSD menus

• To open the OSD menu, press "MENU" on the remote control.

• When the OSD is displayed, use the keys to select any item in the

main menu. After selecting the desired main menu item, press to enter
submenu for feature setting.

• Use the keys to select the desired item and adjust the settings by

using the keys.

• Select the next item to be adjusted in the submenu and adjust as described

above.

• Press "MENU" on the remote control, the screen will return to the main

menu.

• To exit OSD, press "MENU" on the remote control again. The OSD menu

will close and the projector will automatically save the new settings.

Main menu

Color

Display Mode

Wall color

Brightness

Contrast

Saturation

Tint

Color Temperature

Dynamic Black

Gamma

Video

Setting

Press

Off

English

Select

Sub menu

Note: Some of the following OSD settings may not be available. Please
refer to the actual OSD of your projector.
Note: Functions vary depending on model definition.

Adjust

Main Menu

18

Color

English

Display Mode

Wall color

Brightness

Contrast

Saturation

Tint

Color
Temperature

There are many factory presets optimized for various types of
images.

• Bright: For brightness optimization.

• Presentation: For meeting presentation.

• Standard: For common environment.

• Video: For playing video in a bright environment.

• Game: For game content.

• Education: For education environment.

• User: Memorize user's settings.

Use this function to choose a proper color according to the wall.
There are several choices, including white, light yellow, light blue,
pink, dark green. It will compensate the color deviation due to the
wall color to show the correct image tone.

Adjust the brightness of the image.

• Press to darken the image.

• Press to lighten the image.

"Contrast" controls the difference between the lightest and
darkest parts of the picture. Adjusting the contrast changes the
amount of black and white in the image.

• Press to decrease the contrast.

• Press to increase the contrast.

Adjusts a video image from black and white to fully saturated
color.

• Press to decrease the amount of color in the image.

• Press to increase the amount of color in the image.

Adjusts the color balance of red and green.

• Press to increase the amount of green in the image.

• Press to increase the amount of red in the image.

Mode
Use this function to choose CT1, CT2 (Native), CT3, User mode.

R Gain
Adjusts the red gain for color temperature optimization.

G Gain
Adjusts the green gain for color temperature optimization.

B Gain
Adjusts the blue gain for color temperature optimization.

R Bias
Adjusts the red bias for color temperature optimization.

G Bias
Adjusts the green bias for color temperature optimization.

B Bias
Adjusts the blue bias for color temperature optimization.

19

Dynamic Black

Gamma

Note: "Saturation" and "Tint" functions are not supported under computer
or HDMI mode.
Note: Functions vary depending on model definition.

Choose "On" to automatically optimize the display of dark movie
scenes enabling them to be shown in incredible detail.

Effects the representation of dark scenery. With greater gamma
value, dark scenery looks brighter.

English

20

Image

English

Projection

• Front-Desktop: The factory default setting.

• Rear-Desktop: When you select this function, the projector

reverses the image so you can project from behind a translucent
screen.

• Rear-Ceiling: When you select this function, the projector

reverses and inverts the image at same time. You can project from
behind a translucent screen with ceiling mounted projection.

• Front-Ceiling: When you select this function, the projector

inverts the image for ceiling-mounted projection.

Aspect Ratio Use this function to choose your desired aspect ratio.

• Auto: Keep the image with original width-higth ratio and maxi

mize the image to fit native horizontal or vertical pixels.

• 4:3: The image will be scaled to fit the screen and displayed using

a 4:3 ratio.

• 16:9: The image will be scaled to fit the width of the screen and

the height adjusted to display the image using a 16:9 ratio.

Auto Keystone Automatically adjusts vertical image.

Manual Keystone Adjust image distortion caused by tilting projection. (±40 degrees)

<Note> The Manual Keystone function is unavailable under Auto
Keystone setting to "On".

Sharpeness Adjusts the sharpness of the image.

• Press to decrease the sharpness.

• Press to increase the sharpness.

H. Position
(Horizontal
position)

V. Position
(Vertical position)

• Press to move the image left.

• Press to move the image right.

• Press to move the image down.

• Press to move the image up.

Frequency "Frequency" changes the projector's refresh rate to match the

Tracking Synchronizes the signal timing of the projector with the graphics card.

HDMI Color Range Adjust the color range of the HDMI image data to correct color display

frequency of your computer’s graphics card. If you can see a vertical
flickering bar in the projected image, use this function to make the
necessary adjustments.

If you experience an unstable or flickering image, use this function to
correct it.

error.

• Auto: Automatically adjust by information from player.

•

Limited Range: Prosess the input image as limited color range data.

• Full Range: Prosess the input image as full color range data.

21

HDMI Scan Info Adjust the overscan ratio of the HDMI image on screen.

• Auto: Automatically adjust by information from player.

• Underscan: Always no overscan on HDMI image.

• Overscan: Always keep overscan on HDMI image.

Note: "H. Position", "V. Position", "Frequency" and "Tracking" functions
are not supported under HDMI or Video mode.
Note: "HDMI Color Range" and "HDMI Scan Info" functions are only
supported under HDMI mode.
Note: Functions vary depending on model definition.

English

22

Setting

English

Closed Caption

Reset

Security Security

Selects a preferred closed captioning mode from CC1, CC2, CC3,
CC4, (CC1 displays captions in the primary language in your area).
Select "Off" to turn off the captioning feature. This function is only
available when a composite video or S-Video input signal is
selected and its system format is NTSC.
<Note> Set your screen aspect ratio to 4:3. This function is not
available when the aspect ratio is "16:9" or "Auto" .

• Press the button and choose "Yes" to return the

This projector provides a useful security function for the
administrator to manage usage of the projector .

Press to change the "Security" setting. If the security function
is enabled, your must enter the "Administrator Password" first

before changing the security settings.

• Select "On" to enable the security function. The user has to

• If "Off" is selected, then the user can turn on the projector

Timeout(Min.)
Once "Security" is activated to "On", the administrator can set

timeout function.

• Press or to select the timeout interval.

• The range is from 10 minute to 990 minutes.

• When the time is up, the projector will prompt the user to

• The factory default setting of "Timeout(Min.)" is "Off".

• Once the security function is enabled, the projector will

User Password

• Press to setup or change the "User Password".

• Press number keys to set your password on the remote control

• Press to delete character.

• Enter the password when you see "Confirm Password"

• The password should be between 4 and 8 characters long.

• If you select "Request password only when plugging the

• If you select "Always request password while projector turns

parameters on all menus to the factory default settings.

enter a password to operate the projector. Please refer to the
"User Password" section for details.

without password.

enter the password again.

request user to enter password when switch on the projector .
Both "User Password" and "Administrator Password" can be
accepted for this dialogue.

and press "MENU" to confirm.

displayed.

power cord in.", the projector will prompt the user to enter
the password every time the power cord is plugged.

on.", the user has to enter the password every time when the
projector is turned on.

23

Administrator Password
The "Administrator Password" can be used in both the "Enter

Administrator Password" and "Enter Password" dialog boxes.

• Press to change the "Administrator Password".

• The factory default of "Administrator Password" is "1234".

If you forgot your administrator password, do the following to
retrieve the administrator password:

• An unique 6-digit "Universal Password" which is printed on

the Security Card (please check accessory in the box). This
unique password is the number which will be accepted by
projector anytime no matter what the Administrator
Password is.

• If losing this security card and number, please contact with an

Acer service center.

Lock to user startup screen
Default Lock User Startup Screen is "Off". If lock user startup screen

is "On", users cannot change startup screen anymore and avoid
other users change that arbitrarily. Choose "Off" to unlock startup
screen.

Note: Functions vary depending on model definition.

English

24

Management

English

ECO Mode Choose "On" to dim the projector lamp which will lower power

High Altitude Choose "On" to turn on High Altitude mode. Operate the fans at

Turn Off Mode

consumption, extend the lamp life and reduce noise. Choose "Off"
to return normal mode.

full speed continuously to allow for proper high altitude cooling of
the projector.

• Instant Off: Shuts down the projector without fan cooling.

• Instant Resume: Resumes the system when the Power button

is pressed again within 2 minutes.

• SPA: The lamp will flash for 3 minutes each time you shut

down the projector if you enable this mode to extend lamp
life.

• Standard: Properly shuts down the projector after fan

cooling.

Auto Shutdown The projector will automatically shutdown when there is no signal

Lamp Hour Elapse Displays the lamp’s elapsed operating time (in hours).

Lamp Reminding Activate this function to display a reminder to change the lamp 30

Lamp Hour Reset

Note: Functions vary depending on model definition.

input after the allocated time. (default is 120 minutes)

hours before its expected end-of-life.

Press the button and choose "Yes" to turn the lamp hour
counter to 0 hours.

25

3D

3D Choose "On" to enable DLP 3D function.

• On: Choose this item while using DLP 3D glasses, 120Hz 3D

capable graphics cards and HQFS format file or DVD with
corresponding SW player.

• Off: Turn off 3D mode.

3D Format If the 3D content is not displayed correctly, you can select a 3D

3D L/R Invert If you see a discrete or overlapping image while wearing DLP 3D

3D Warning Message Choose "On" to display the 3D warning message.

Note: It needs correct settings on graphic card 3D application program for
correct 3D display.
Note: The SW players, such as Stereoscopic Player and DDD TriDef Media
Player can support 3D format files. You can download these three players
on web page below,

- Stereoscopic Player (Trial):
http://www.3dtv.at/Downloads/Index_en.aspx

- DDD TriDef Media Player (Trial):
http://www.tridef.com/download/TriDef-3-D-Experience-4.0.2.html

Note: "3D L/R Invert" is only available when 3D is enabled.
Note: There has reminder screen if 3D still enable when power on projector.
Please adjust setting depended on your purpose.

format that suits the 3D content you are viewing and obtain the
best result.

glasses, you may need to execute "Invert" to get best match of
left/right image sequence to get the correct image (for DLP 3D).

Note: 3D display is now enabled.

1. Please make sure you have the correct 3D signals and glasses.

2. Remember to turn 3D off if you don°¶t want to see 3D images.

3. If the 3D display isn°¶t correct, please try to enable 3D Sync Invert.

4. Display mode options will be disabled while in 3D mode.

English

Language

Language

Choose the multilingual OSD menu. Use the or key

to select your preferred menu language.

• Press to confirm the selection.

26

Appendices

English

Troubleshooting

If you experience a problem with your Acer projector, refer to the following
troubleshooting guide. If the problem persists, please contact your local reseller
or service center.

Image Problems and Solutions

# Problem Solution

1 No image appears

onscreen

2 Partial, scrolling

or incorrectly
displayed image
(for PC (Windows
2000/XP/Vista/
Windows 7/
Windows 8))

• Connected as described in the "Getting Started"

section.

• Ensure none of the connector pins are bent or

broken.

• Check if the projector lamp has been securely

installed. Please refer to the "Replacing the Lamp"
section.

• Make sure you have removed the lens cap and the

projector is switched on.

• For an incorrectly displayed image:

• Open "My Computer", open the "Control

Panel", and then double-click the "Display"
icon.

• Select the "Settings" tab.

• Verify that your display resolution setting is

lower than or equal to WUXGA-RB (1920 x

1200).

• Click the "Advanced Properties" button.

If the problem still appears, change the monitor display
you are using and follow the steps below:

• Verify that the resolution setting is lower than

or equal to WUXGA-RB (1920 x 1200).

• Click the "Change" button under the

"Monitor" tab.

• Click "Show all devices". Next, select "Standard

monitor types" under the SP box, and choose
the resolution mode you need under the
"Models" box.

• Verify that the resolution setting of the

monitor display is lower than or equal to
WUXGA-RB (1920 x 1200).

27

3 Partial, scrolling

or incorrectly
displayed image
(For notebooks)

4 The screen of the

notebook
computer is not
displaying your
presentation

5 Image is unstable

or flickering

6 Image has vertical

flickering bar

7 Image is out of

focus

• For an incorrectly displayed image:

• Follow the steps for item 2 (above) to adjust

the resolution of your computer.

• Press the toggle output settings. Example:

[Fn]+[F4], Compaq [Fn]+[F4], Dell [Fn]+[F8],
Gateway [Fn]+[F4], IBM [Fn]+[F7], HP [Fn]+[F4],
NEC [Fn]+[F3], Toshiba [Fn]+[F5]

• If you experience difficulty changing resolutions or

your monitor freezes, restart all equipment
including the projector.

• If you are using a Microsoft

notebook: Some notebook PCs may deactivate their
own screens when a second display device is in use.
Each has a different way to be reactivated. Refer to
your computer's manual for detailed information.

• If you are using an Apple

notebook: In System Preferences, open Display and
select Video Mirroring "On".

®

Windows® based

®

Mac® OS based

• Adjust the "Tracking" to correct it. Refer to the

"Image" section for more information.

• Change the display color depth settings on your

computer.

• Use "Frequency" to make an adjustment. Refer to

the "Image" section for more information.

• Check and reconfigure the display mode of your

graphics card to make it compatible with the
projector.

• Make sure the lens cap is removed.

• Adjusts the focus ring on the projector lens.

• Make sure the projection screen is within the

required distance of 3.3 to 39.2 feet (1.0 to 11.9
meters) (SVGA/XGA series) / 3.3 to 31.8 feet (1.0 to

9.7 meters) (WXGA series) from the projector. Refer
to the "How to Get a Preferred Image Size by
Adjusting Distance and Zoom" section for more
information.

English

8 Image is stretched

when displaying a
"widescreen"
DVD title

When you play a DVD encoded in anamorphic or 16:9
aspect ratio you may need to adjust the following
settings:

• If you play a 4:3 format DVD title, please change the

format to 4:3 in the projector OSD.

• If the image is still stretched, you will also need to

adjust the aspect ratio. Set up the display format to
16:9 (wide) aspect ratio on your DVD player.

28

English

9 Image is too small

or too large

10 Image has slanted

sides

11 Image is reversed

• Adjust the zoom lever on the top of the projector.

• Move the projector closer to or further from the

screen.

• Press "MENU" on the remote control. Go to "Image -

-> Aspect Ratio" and try different settings or press
"RATIO" on the remote control to adjust directly.

• If possible, reposition the projector so that it is

centered on the screen.

• Press the "Keystone / " button on the remote

control until the sides are vertical.

• Press "MENU" on the remote control. Go to "Image -

-> Auto Keystone" and choose "Off" on the OSD, if
"Keystone" button is not available on the remote
control.

• Select "Image --> Projection" on the OSD and adjust

the projection direction.

29

OSD Messages

# Condition Message Reminder

1 Message Fan Fail - the system fan is not working.

Lamp will automatically turn off soon.

Projector Overheated - the projector has exceeded its
recommended operating temperature and must be allowed to
cool down before it may be used.

Lamp will automatically turn off soon.

Replace the lamp - the lamp is about to reach its maximum
lifetime. Prepare to replace it soon.

Lamp is approaching the end of its useful life in full power operation.

Fan Fail.

Projector Overheated.

Replacement suggested!

Problems with the Projector

# Condition Solution

English

1 The projector stops responding

to all controls

2 Lamp burns out or makes a

popping sound

If possible, turn off the projector, then
unplug the power cord and wait at least 30
seconds before reconnecting power.

When the lamp reaches the end of its useful
life, it will burn out and may make a loud
popping sound. If this happens, the projector
will not turn on until the lamp module has
been replaced. To replace the lamp, follow
the procedures in the "Replacing the Lamp"
section.

30

LED & Alarm Definition Listing

English

LED Messages

Message

Standby -- -- ON --

Power button ON -- -- -- ON

Lamp retry -- -- -- Quick

Power off (Cooling
state)

Power button OFF
(cooling completed;

standby mode)

Firmware download ON ON ON --

Error (thermal failure) -- ON -- ON

Error (fan lock) -- Quick

Error (lamp breakdown) ON -- -- ON

Error (color wheel fail) Quick

Lamp_LED Temp_LED Power LED

Red Red Red Blue

-- -- Quick

-- -- ON --

Flashing

Flashing

-- -- ON

Flashing

-- ON

Flashing

--

31

Cleaning and replacing the dust filters

Cleaning the dust filters

Clean the dust filters after every 1000 hours of use. If they are note cleaned
periodically, they can become clogged with dust, preventing proper ventilation.
This can cause overheating and damage the projector.

2

1

Follow these steps:
1 Turn the projector off. Wait for the Power LED to stop flashing then

unplug the power cord.
2 Allow the projector at least 30 mins to cool down.
3 Pull out the dust filter. (Illustration #1)
4 To clean the dust filters, use a small vacuum cleaner designed for

computers and other office equipment. (Illustration #2)
5 If the dirt is difficult to remove or the filter is broken, please contact your

local dealer or service center to obtain a new filter.

English

English

32

Replacing the Lamp

Use a screwdriver to remove the screw(s) from the cover, and then pull out the
lamp.

The projector will detect the lamp life. You will be shown a warning message
"Lamp is approaching the end of its useful life in full power operation.
Replacement suggested!" When you see this message, change the lamp as soon
as possible. Make sure the projector has been cooling down for at least 30
minutes before changing the lamp.

Warning: The lamp compartment is hot! Allow it to cool down
before changing the lamp.

3

4

5

2

1

To Change the Lamp
Turn off the projector by pressing the Power button.
Allow the projector at least 30 minutes to cool down.
Disconnect the power cord.
1 Use a screwdriver to remove the screw from the cover. (Illustration #1)

Push up and remove the cover. (Illustration #2)

2 Remove the screw that secure the lamp module. (Illustration #3)

Pull out the lamp plug. (Illustration #4)

3 Lift the handle so that it stands up. Pull out the lamp module by force.

(Illustration #5)

To replace the lamp module, use a new lamp and reverse the above steps.

Warning: To reduce the risk of personal injury, do not drop the
lamp module or touch the lamp bulb. The bulb may shatter and
cause injury if it is dropped.

33

Ceiling Mount Installation

If you wish to install the projector using a ceiling mount, please refer to the
steps below:

1 Drill four holes into a solid, structurally sound part of the ceiling, and

secure the mount base.

13

mm

20

mm

49.9

mm

mm

8.4

Note: Screws are not included. Please obtain the appropriate
screws for your type of ceiling.

2 Secure the ceiling rod using the appropriate type of four-cylinder screws.

Ceiling Mount Base

Short Rod

- Attach to ceiling

English

130 mm

50 mm length / 8 mm diameter -

Screw Type A

Long Rod

Extension Rod

Long Cylinder Cap
Allen Key

- For tightening/loosening

Tightening Screw

Medium Rod

English

34

3 Use the appropriate number of screws for the projector size to attach the

projector to the ceiling mount bracket.

Smaller Washer

Large Washer

Projector Bracket

Supports projector and

allows for adjustments

-

Note: It is recommended that you keep a reasonable space
between the bracket and the projector to allow for proper heat
distribution. Use two washers for extra support, if deemed
necessary.

4 Attach the ceiling bracket to the ceiling rod.

Screw Type B

Spacer

- For heat dissipation

Screw Type A

50 mm length/

8 mm diameter

Large cylinder cap

Allen Key

- For tightening/loosening

-

Tightening Screw

35

5 Adjust the angle and positioning as necessary.

Tightening Screw

Allen Key

Allen Key

Tightening Screw

Note: The appropriate type of screw and washer for each model is
listed in the table below. 4 mm diameter screws are enclosed in

the screw pack.

Screw Type B Washer Type

Diameter (mm) Length (mm) Large Small

425VV

English

SCREW SPEC. M4 x 25 mm

112 154.5

68.8

37

84.4

66.9

207.6

21.5

28.8

76.5

84.9

13.5

English

36

Specifications

The specifications listed below are subject to change without notice. For final
specs, please refer to Acer's published marketing specifications.

Projection system

Resolution

Computer compatibility IBM PC and compatibles, Apple Macintosh, iMac and

Video compatibility NTSC (3.58/4.43), PAL (B/D/G/H/I/M/N), SECAM (B/D/G/

Aspect ratio 4:3, 16:9

Displayable colors 16.7 million colors

Projection lens F = 2.51 ~ 2.69, f = 21.95~24.18 mm, 1.1X manual

Projection screen size (diagonal)

Projection distance

®

DLP

• X112H/D402D/EV-S33H/V31S/AS311/P1120/X1120H/

D401D/EV-S32H/X1120/D401/EV-S32 series: Native
800 x 600 SVGA resolution

• X122H/D412D/EV-X33H/V31X/AX312/X122/D412/

EV-X33/V30X/AX302/P1223/D413D/EV-X34H/X1223/
D413/EV-X34/P1220n/X1220Hn/D411DT/EV-X32HG/
P1220/X1220H/D411D/EV-X32H/X1220/D411/EV-X32
series: Native 1024 x 768 XGA resolution

• X132WH/D422D/EV-W33H/V31W/AW312/P1320W/

X1320WH/D421D/EV-W32H series: Native 1280 x
800 WXGA resolution

• Maximum: UXGA (1600 x 1200), WUXGA-RB (1920 x

1200)

VESA standards: SXGA, XGA, VGA, SVGA, SXGA+,
WXGA, WXGA+, WSXGA +

K/K1/L), HDTV (720p, 1080i, 1080p), EDTV (480p,
576p), SDTV (480i, 576i)

zoom and manual focus

• X112H/D402D/EV-S33H/V31S/AS311/P1120/X1120H/

D401D/EV-S32H/X1120/D401/EV-S32/X122H/D412D/
EV-X33H/V31X/AX312/X122/D412/EV-X33/V30X/
AX302/P1223/D413D/EV-X34H/X1223/D413/EV-X34/
P1220n/X1220Hn/D411DT/EV-X32HG/P1220/
X1220H/D411D/EV-X32H/X1220/D411/EV-X32 series:
23" (57 cm) ~ 300" (762 cm)

• X132WH/D422D/EV-W33H/V31W/AW312/P1320W/

X1320WH/D421D/EV-W32H series:
26" (66 cm) ~ 300" (762 cm)

• X112H/D402D/EV-S33H/V31S/AS311/P1120/X1120H/

D401D/EV-S32H/X1120/D401/EV-S32/X122H/D412D/
EV-X33H/V31X/AX312/X122/D412/EV-X33/V30X/
AX302/P1223/D413D/EV-X34H/X1223/D413/EV-X34/
P1220n/X1220Hn/D411DT/EV-X32HG/P1220/
X1220H/D411D/EV-X32H/X1220/D411/EV-X32 series:

3.3' (1.0 m) ~ 39.2' (11.9 m)

• X132WH/D422D/EV-W33H/V31W/AW312/P1320W/

X1320WH/D421D/EV-W32H series:

3.3' (1.0 m) ~ 31.8' (9.7 m)

37

Throw ratio

• X112H/D402D/EV-S33H/V31S/AS311/P1120/X1120H/

D401D/EV-S32H/X1120/D401/EV-S32/X122H/D412D/
EV-X33H/V31X/AX312/X122/D412/EV-X33/V30X/
AX302/P1223/D413D/EV-X34H/X1223/D413/EV-X34/
P1220n/X1220Hn/D411DT/EV-X32HG/P1220/
X1220H/D411D/EV-X32H/X1220/D411/EV-X32 series:
50"@2 m (1.96 ~ 2.18:1)

• X132WH/D422D/EV-W33H/V31W/AW312/P1320W/

X1320WH/D421D/EV-W32H series: 62"@2 m (1.50 ~

1.80:1)

Horizontal scan rate 15k - 100 kHz

Vertical refresh scan rate 24 -120 Hz

Lamp type 190W user-replaceable lamp

Keystone correction

Weight 2.3 Kg (6.16 Ibs)

Dimensions (W x D x H) 289.3 mm X 234.5 mm X 92.3 mm (11.4" x 9.2" x 3.6")

Digital Zoom 2X(PC)/1.8X(Video)

Power supply AC input 100 - 240 V auto-switching power supply

Power consumption Normal mode: 250W ± 10% @ 110VAC

Operating temperature 0ºC to 40ºC / 32ºF to 104ºF

Standard package contents

± 40 degrees

ECO mode: 215W ± 10% @ 110VAC
Standby mode < 0.5W

• AC power cord x1

• VGA cable x1

• Remote control x1

• Battery x2 (for remote control) (option)

• User's guide (CD-ROM) x1

• Quick start guide x1

• Security card x1

• Carrying case x1 (option)

English

X112H/D402D/EV-S33H/V31S/AS311/P1120/
X1120H/D401D/EV-S32H/X1120/D401/EV­S32/X122H/D412D/EV-X33H/V31X/AX312/

I/O connectors

Power socket V V

VGA V V

Composite video V V

RS232 V V

HDMI V X

P1223/D413D/EV-X34H/X1223/D413/EV­X34/P1220n/X1220Hn/D411DT/EV-X32HG/
P1220/X1220H/D411D/EV-X32H/X1220/
D411/EV-X32/X132WH/D422D/EV-W33H/
V31W/AW312/P1320W/X1320WH/D421D/
EV-W32H

X122/D412/EV-X33/
V30X/AX302

English

38

I/O connectors

Mini USB x1 (for
firmware
upgrade)

X112H/D402D/EV-S33H/V31S/AS311/P1120/
X1120H/D401D/EV-S32H/X1120/D401/EV­S32/X122H/D412D/EV-X33H/V31X/AX312/
P1223/D413D/EV-X34H/X1223/D413/EV­X34/P1220n/X1220Hn/D411DT/EV-X32HG/
P1220/X1220H/D411D/EV-X32H/X1220/
D411/EV-X32/X132WH/D422D/EV-W33H/
V31W/AW312/P1320W/X1320WH/D421D/
EV-W32H

VV

X122/D412/EV-X33/
V30X/AX302

Note: Design and specifications are subject to change without
notice.

39

Compatibility modes

A. VGA Analog

1 VGA Analog - PC Signal

Modes Resolution V.Frequency [Hz] H.Frequency [KHz]

VGA 640x480 60 31.5

640x480 72 37.9
640x480 75 37.5
640x480 85 43.3
640x480 120 61.9

SVGA 800x600 56 35.1

800x600 60 37.9
800x600 72 48.1
800x600 75 46.9
800x600 85 53.7
800x600 120 77.4

XGA 1024x768 60 48.4

1024x768 70 56.5
1024x768 75 60.0
1024x768 85 68.7
1024x768 120 99.0

SXGA 1152x864 70 63.8

1152x864 75 67.5

1152x864 85 77.1
1280x1024 60 64.0
1280x1024 72 77.0
1280x1024 75 80.0
1280x1024 85 91.1

QuadVGA 1280x960 60 60.0

1280x960 75 75.2

SXGA+ 1400x1050 60 65.3

UXGA 1600x1200 60 75.0
PowerBook G4 640x480 60 31.4
PowerBook G4 640x480 66.6(67) 34.9
PowerBook G4
PowerBook G4
PowerBook G4 1152x870 75 68.7
PowerBook G4 1280x960 75 75.0

i Mac DV (G3) 1024x768 75 60.0

800x600 60 37.9

1024x768 60 48.4

English

English

40

2 VGA Analog - Extended Wide timing

Modes Resolution V.Frequency [Hz] H.Frequency [KHz]
WXGA 1280x768 60 47.8

1280x768 75 60.3
1280x768 85 68.6
1280x720 60 44.8
1280x720 120 92.9
1280x800 60 49.6

*1280x800-RB 119.909 101.6

1440x900 60 59.9

WSXGA+ 1680x1050 60 65.3

1920x1080

(1080P)

1366x768 60 47.7

WUXGA 1920x1200-RB 59.94 74.04

60 67.5

3 VGA Analog -Component Signal

Modes Resolution V.Frequency [Hz] H.Frequency [KHz]

480i 720x480(1440x480) 59.94 (29.97) 15.7

576i 720x576(1440x576) 50(25) 15.6
480p 720x480 59.94 31.5
576p 720x576 50 31.6
720p 1280x720 60 45.0
720p 1280x720 50 37.5

1080i 1920x1080 60(30) 33.8

1080i 1920x1080 50(25) 28.1
1080p 1920x1080 23.97/24 27.0
1080p 1920x1080 60 67.5
1080p 1920x1080 50 56.3

B. HDMI Digital

1 HDMI - PC Signal

Modes Resolution V.Frequency [Hz] H.Frequency [KHz]

VGA 640x480 60 31.5

640x480 72 37.9
640x480 75 37.5
640x480 85 43.3
640x480 120 61.9

41

SVGA 800x600 56 35.1

800x600 60 37.9
800x600 72 48.1
800x600 75 46.9
800x600 85 53.7
800x600 120 77.4

XGA 1024x768 60 48.4

1024x768 70 56.5
1024x768 75 60.0
1024x768 85 68.7
1024x768 120 99.0

SXGA 1152x864 70 63.8

1152x864 75 67.5

1152x864 85 77.1
1280x1024 60 64.0
1280x1024 72 77.0
1280x1024 75 80.0
1280x1024 85 91.1

QuadVGA 1280x960 60 60.0

1280x960 75 75.2

SXGA+ 1400x1050 60 65.3

UXGA 1600x1200 60 75.0
PowerBook G4 640x480 60 31.4
PowerBook G4 640x480 66.6(67) 34.9
PowerBook G4
PowerBook G4
PowerBook G4 1152x870 75 68.7
PowerBook G4 1280x960 75 75.0

i Mac DV (G3) 1024x768 75 60.0

800x600 60 37.9

1024x768 60 48.4

English

2 HDMI - Extended Wide timing

Modes Resolution V.Frequency [Hz] H.Frequency [KHz]
WXGA 1280x768 60 47.8

1280x768 75 60.3
1280x768 85 68.6
1280x720 60 44.8
1280x720 120 92.9
1280x800 60 49.6

*1280x800-RB 119.909 101.6

1440x900 60 59.9

WSXGA+ 1680x1050 60 65.3

42

English

1920x1080

(1080P)

1366x768 60 47.7

WUXGA 1920x1200-RB 59.94 74.04

60 67.5

3 HDMI - Video Signal

Modes Resolution V.Frequency [Hz] H.Frequency [KHz]

480i 720x480(1440x480) 59.94 (29.97) 15.7

576i 720x576(1440x576) 50(25) 15.6
480p 720x480 59.94 31.5
576p 720x576 50 31.6
720p 1280x720 60 45.0
720p 1280x720 50 37.5

1080i 1920x1080 60(30) 33.8

1080i 1920x1080 50(25) 28.1
1080p 1920x1080 23.97/24 27.0
1080p 1920x1080 60 67.5
1080p 1920x1080 50 56.3

4 HDMI - 1.4a 3D Timing

Modes Resolution V.Frequency [Hz] H.Frequency [KHz]

720p (Frame Packing) 1280x720 50 37.5
720p (Frame Packing) 1280x720 60 45.0

1080p (Frame Packing ) 1920x1080 24 27.0

720p (Frame Packing) 1280x720 50 37.5

720p (Frame Packing) 1280x720 60 45.0
1080i (Top and Bottom) 1920x1080 50 (25) 28.1
1080i (Top and Bottom) 1920x1080 60 (30) 33.8

1080p (Top and Bottom) 1920x1080 24 27.0
1080p (Top and Bottom) 1920x1080 50 56.3
1080p (Top and Bottom) 1920x1080 60 67.5

720p (Side by Side (Half)) 1280x720 60 45.0
1080i (Side by Side (Half)) 1920x1080 50 (25) 28.1
1080i (Side by Side (Half)) 1920x1080 60 (30) 33.8

1080p (Side by Side (Half)) 1920x1080 50 56.3
1080p (Side by Side (Half)) 1920x1080 60 67.5

Graphic source monitor

range limits

Horizontal scan rate:

Vertical scan rate:

Max. pixel rate:

15k-100kHz

24-120 Hz

165 MHz

Note: * Functions vary depending on model definition.

43

English

44

Regulations and safety notices

English

FCC notice

This device has been tested and found to comply with the limits for a Class B
digital device pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This device generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular
installation. If this device does cause harmful interference to radio or television
reception, which can be determined by turning the device off and on, the user
is encouraged to try to correct the interference by one or more of the following
measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the device and receiver.

• Connect the device into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio/television technician for help.

Notice: Shielded cables

All connections to other computing devices must be made using shielded cables
to maintain compliance with FCC regulations.

Notice: Peripheral devices

Only peripherals (input/output devices, terminals, printers, etc.) certified to
comply with the Class B limits may be attached to this equipment. Operation
with non-certified peripherals is likely to result in interference to radio and TV
reception.

Caution

Changes or modifications not expressly approved by the manufacturer could
void the user's authority, which is granted by the Federal Communications
Commission, to operate this device.

Operation conditions

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.

Notice: Canadian users

This Class B digital apparatus complies with Canadian ICES-003.

45

Remarque à l'intention des utilisateurs canadiens

Cet appareil numérique de la classe B est conforme a la norme NMB-003 du
Canada.

Declaration of Conformity for EU countries

Acer hereby declares that this projector series is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.

Compliant with Russian regulatory certification

001

Radio device regulatory notice

Note: The regulatory information below is for models with
wireless LAN and/or Bluetooth only.

General

This product complies with the radio frequency and safety standards of any
country or region in which it has been approved for wireless use. Depending on
configurations, this product may or may not contain wireless radio devices (such
as wireless LAN and/or Bluetooth modules).

English

English

Canada — Low-power license-exempt radio
communication devices (RSS-210)

a Common information

Operation is subject to the following two conditions:

1. This device may not cause interference, and

2. This device must accept any interference, including interference
that may cause undesired operation of the device.

b Operation in 2.4 GHz band

To prevent radio interference to the licensed service, this device is
intended to be operated indoors and installation outdoors is subject
to licensing.

List of applicable countries

This device must be used in strict accordance with the regulations and constraints in the
country of use. For further information, please contact the local office in the country of use.
Please see http://ec.europa.eu/enterprise/rtte/implem.htm

for the latest country list.

Acer Incorporated

j

8F, 88, Sec. 1, Xintai 5th Rd., Xizhi

New Taipei City 221, Taiwan

We,

Acer Incorporated

8F, 88, Sec. 1, Xintai 5th Rd., Xizhi, New Taipei City 221, Taiwan
Contact Person: Mr. RU Jan, e-mail: [e-mail]

And,

Acer Italy s.r.l

Via Lepetit, 40, 20020 Lainate (MI) Italy
Tel: [phone] ,Fax: [phone]
www.acer.it

Declaration of Conformity

Declare under our own responsibility that the product:

Product: DLP Pro
Trade Name: Acer
Model Number: FWX1344/FNX1342/FNX1341/

To which this declaration refers conforms to the relevant standard or other standardizing documents:

x EN55022:2010 Class B; EN 55024:2010
x EN61000-3-2:2006+A1:2009+A2:2009, Class A
x EN61000-3-3:2008
x EN 60950-1:2006/A11:2009/A1:2010+A12:2011
x Regulation (EC) No. 1275/ 2008; EN 62301:2005
x EN50581:2012

We hereby declare above product is in compliance with the essential requirements and other relevant
provisions of EMC Directive 2004/108/EC, Low Voltage Directive 2006/95/EC and RoHS Directive
2011/65/EU and Directive 2009/125/EC with regard to establishing a framework for the setting of ecodesign
requirements for energy-related product.

ector

FSV1343/FNX1107/FNX1108/FWX1103/
FNX1109/FNX1102/FNX1102/FSV1101/FSV1101/
X112H/D402D/EV­S33H/V31S/AS311/P1120/X1120H/D401D/EV­S32H/X1120/D401/EV-S32/X122H/D412D/EV­X33H/V31X/AX312/X122/D412/EV­X33/V30X/AX302/P1223/D413D/EV-X34H/X1223/D413/EV­X34/P1220n/X1220Hn/D411DT/EV­X32HG/P1220/X1220H/D411D/EV-X32H/X1220/D411/EV­X32/X132WH/D422D/EV­W33H/V31W/AW312/P1320W/X1320WH/D421D/EV­W32H

Year to begin affixing CE marking 2014

_______________________________

RU Jan / Sr. Manager Date
Regulation, Acer Inc.

Oct. 1, 2014

Acer America Corporation

333 West San Carlos St.,

Suite 1500

San Jose, CA 95110

U. S. A.

Tel: [phone]

Fax: [phone]

www.acer.com

Federal Communications Commission

Declaration of Conformity

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.

The following local Manufacturer / Importer is responsible for this declaration:

Product: DLP Projector
Model Number: FWX1344/FNX1342/FNX1341/FSV1343/FNX1

Machine Type: X112H/D402D/EV-

Name of Responsible Party: Acer America Corporation
Address of Responsible Party: 333 West San Carlos St.

Contact Person: Acer Representative
Phone No.: 254-298-4000
Fax No.: 254-298-4147

107/FNX1108/FWX1103/FNX1109/FNX1102/F
NX1102/FSV1101/FSV1101

S33H/V31S/AS311/P1120/X1120H/D401D/EV­S32H/X1120/D401/EV-S32/X122H/D412D/EV­X33H/V31X/AX312/X122/D412/EV­X33/V30X/AX302/P1223/D413D/EV­X34H/X1223/D413/EV­X34/P1220n/X1220Hn/D411DT/EV­X32HG/P1220/X1220H/D411D/EV­X32H/X1220/D411/EV­X32/X132WH/D422D/EV­W33H/V31W/AW312/P1320W/X1320WH/D421
D/EV-W32H

Suite 1500
San Jose, CA 95110
U. S. A.