PCI Disk Array
Controller Drivers
Installation Guide and
User Manual
Part Number 775079-01
08P4100
© Copyright 2000 Mylex Corporation.
All Rights Reserved.
All contents of this manual are copyrighted by Mylex Corporation. The information contained herein is the exclusive property of Mylex Corporation and shall not be copied, transferred, photocopied, translated on paper, film, electronic media, or computer-readable form; or otherwise reproduced in any way, without the express written permission of Mylex Corporation.
Greetings
This manual describes the Mylex PCI Disk Array Controllers.
Requests for technical information about this and other Mylex Corporation products should be made to your Mylex authorized reseller or Mylex marketing representative.
Please Notice
IBM, Mylex, DAC960, DAC1100, Global Array Manager, GAM, RAID EzAssist, AcceleRAID, and eXtremeRAID are trademarks or registered trademarks of International Business Machines Corp. and its subsidiaries. MS-DOS, Windows 95, Windows 98, Windows NT, and Windows 2000 are registered trademarks of Microsoft Corporation. Novell and NetWare are registered trademarks of Novell, Inc. SCO, SCO UNIX, and
UnixWare are registered trademarks of The Santa Cruz Operation, Ltd. Solaris is a registered trademark of Sun Microsystems, Inc. Linux is written and distributed under the GNU General Public License which means that its source code is freely-distributed and available to the general public. SuSE is a trademark of SuSE Incorporated. Caldera is a
trademark of Caldera Systems Incorporated. Redhat is a registered trademark of Redhat Incorporated. QLogic is a trademark of QLogic Corporation. Other names that are trademarks may be used herein for the purpose of identifying the products or services of their respective owners.
Unless otherwise noted, companies, names and data used in examples herein are fictitious.
Our Policy
Although reasonable efforts have been made to assure the accuracy of the information contained herein, this publication could include technical inaccuracies or typographical errors. Mylex Corporation expressly disclaims liability for any error in this information, and for damages, whether direct, indirect, special, exemplary, consequential or otherwise, that may result from such error, including but not limited to loss of profits resulting from the use or misuse of the manual or information contained therein (even if Mylex Corporation has been advised of the possibility of such damages). Any questions or comments regarding this document or its contents should be addressed to Mylex Corporation at the address shown on the cover.
The following paragraph does not apply to the United Kingdom or any country where such provisions are inconsistent with local law:
MYLEX CORPORATION PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Some states do not allow disclaimer of express or implied warranties or the limitation or exclusion of liability for indirect, special, exemplary, incidental or consequential damages in certain transactions; therefore, this statement may not apply to you. Also, you may have other rights which vary from jurisdiction to jurisdiction.
Information in this publication is subject to change without notice and does not represent a commitment on the part of Mylex Corporation. Changes may be made periodically to the information herein; these changes will be incorporated in new editions of the publication. Mylex Corporation reserves the right to make improvements and/or changes at any time in the product(s) and/or program(s) described in this publication.
It is possible that this publication may contain reference to, or information about, Mylex Corporation products (machines and programs), programming or services that are not announced in your country. Such references or information must not be construed to mean that Mylex Corporation intends to announce, provide, or make available such Mylex products, programming, or services in your jurisdiction.
About This Manual
This installation guide covers the steps involved to install and use the software drivers for Mylex PCI Disk Array Controllers.
For information on defining and setting RAID (Redundant Array of Independent Disks) levels as well as configuration of the array, consult the appropriate Global Array Manager Client manual or the RAID EzAssist Configuration Utility User Reference Guide or RAID EzAssist Configuration Utility Quick Configuration Guide.
Conventions
Throughout the manual, the following conventions are used to describe user interaction with the product:
bold |
The user must enter the bold text exactly as shown |
|
Press the Enter key |
Enter |
Press the key labeled “Enter” (or “Delete”, etc.) |
File, Run |
Select the Run option from the pull-down menu |
|
activated when the File menu pad is selected |
Note
Supplementary information that can have an effect on system performance
Caution
Notification that a proscribed action has the potential to adversely affect equipment operation, system performance, or data integrity
WARNING
Notification that a proscribed action will definitely result in equipment damage, data loss, or personal injury
NetWare
Windows NT
Windows 2000
SCO OpenServer
UnixWare
Solaris
Linux
2
3
4
5
6
7
8
vi |
PCI Disk Array Controller Drivers Manual |
Contents
Chapter 1
Introduction
Overview ........................................................................................... |
1-1 |
NetWare, Windows NT, and Windows 2000 .............................. |
1-1 |
SCO OpenServer, UnixWare, and Solaris ................................. |
1-2 |
Linux ........................................................................................... |
1-2 |
Requirements .................................................................................... |
1-2 |
Chapter 2 |
|
NetWare |
|
Overview ........................................................................................... |
2-1 |
Mylex Disk Array Controller Driver Files for NetWare ................ |
2-1 |
Tape, Disk, and CD-ROM Support ............................................. |
2-1 |
Installing the Mylex Disk Array Controller as the Primary |
|
NetWare 4.2 Controller .................................................................... |
2-2 |
Installing NetWare 4.2 Drivers .................................................... |
2-2 |
Installing Peripherals Under NetWare 4.2 .................................. |
2-3 |
Installing the Mylex Disk Array Controller into an |
|
Existing NetWare 4.2 System .................................................. |
2-4 |
Installing the Mylex Disk Array Controller as the Primary |
|
NetWare 5.0 Controller .................................................................... |
2-6 |
Installing NetWare 5.0 Drivers .................................................... |
2-6 |
NetWare 5.0 Bootable CD-ROM ................................................ |
2-7 |
Installing Peripherals Under NetWare 5.0 .................................. |
2-8 |
Installing the Mylex Disk Array Controller into an |
|
Existing NetWare 5.0 System .................................................. |
2-9 |
Chapter 3 |
|
Windows NT |
|
Overview ........................................................................................... |
3-1 |
Mylex Disk Array Controller Driver Files for Windows NT .......... |
3-1 |
Installing the Mylex Disk Array Controller as the Primary Windows |
|
NT 4.0 Controller ............................................................................. |
3-3 |
Installing the Mylex Disk Array Controller into an Existing |
|
Windows NT 4.0 System ................................................................. |
3-5 |
Manual No. 775079 |
vii |
Chapter 4
Windows 2000
Overview ............................................................................................ |
4-1 |
Mylex Disk Array Controller Driver Files for Windows 2000 ....... |
4-1 |
Installing the Mylex Disk Array Controller as the Primary |
|
Windows 2000 Controller ................................................................. |
4-3 |
Installation Procedure 1: Using eXtremeRAID 2000, |
|
eXtremeRAID 3000, AcceleRAID 160/170LP, |
|
AcceleRAID 170, or AcceleRAID 352 ....................................... |
4-4 |
Primary (new) Installation .................................................... |
4-4 |
Secondary (new) Installation ............................................... |
4-4 |
Secondary (existing) Installation ......................................... |
4-4 |
A secondary existing installation is when: ........................... |
4-4 |
Performing a Primary Installation ............................................... |
4-5 |
Performing a Secondary Installation ........................................... |
4-7 |
Microsoft Windows 2000 Installation Procedure ......................... |
4-7 |
Installation Procedure 2: Using DAC960P Series, |
|
eXtremeRAID 1100 (DAC1164P), AcceleRAID 150, |
|
AcceleRAID 200, or AcceleRAID 250 ..................................... |
4-13 |
Primary (new) Installation .................................................. |
4-13 |
Secondary (new) Installation ............................................. |
4-13 |
Secondary (existing) Installation ....................................... |
4-13 |
Upgrading the Windows 2000 Driver to the Current |
|
Mylex Driver ............................................................................. |
4-14 |
Upgrading Windows NT 4.0 to Windows 2000 ......................... |
4-14 |
Windows NT 4.0 with a Mylex controller ........................... |
4-14 |
Windows NT 4.0 with GAM Server/GAM Client |
|
Installed ........................................................................... |
4-15 |
Windows NT 4.0 with a Mylex Controller with |
|
MACDISK installed .......................................................... |
4-15 |
Updating the Mylex Controller Driver ............................................... |
4-16 |
Chapter 5 |
|
SCO OpenServer |
|
Overview ............................................................................................ |
5-1 |
Creating a Driver Diskette for SCO UNIX .......................................... |
5-2 |
Installing the Mylex Disk Array Controller as the Primary |
|
Controller ......................................................................................... |
5-3 |
Installing Additional Mylex Disk Array Controllers ............................. |
5-5 |
Adding System Drives ....................................................................... |
5-6 |
Installing Mylex Disk Array Controller Tape Drivers .......................... |
5-7 |
Mylex Disk Array Controller CD-ROM Drivers ..................... |
5-8 |
viii |
PCI Disk Array Controller Drivers Manual |
Installing the Mylex Disk Array Controller as a |
|
Secondary Controller ............................................................... |
5-9 |
Secondary Controller Installation Procedure ...................... |
5-9 |
Updating a Previously Installed Driver ..................................... |
5-11 |
Tuning SCO for Maximum Performance .................................. |
5-11 |
Chapter 6 |
|
UnixWare |
|
Overview ........................................................................................... |
6-1 |
Special Notes ............................................................................. |
6-2 |
Creating a Driver Diskette for UnixWare ........................................... |
6-3 |
Installing the Mylex Disk Array Controller as the Primary |
|
UnixWare Controller with UnixWare 7.x/2.1.3 ................................ |
6-3 |
Installing the Mylex Disk Array Controller as the Secondary |
|
UnixWare Controller with UnixWare 7.x/2.1.3 ................................. |
6-5 |
Installing the Mylex Disk Array Controller as the Primary |
|
UnixWare Controller with UnixWare 2.1.2 ....................................... |
6-6 |
Installing the Mylex Disk Array Controller as the Secondary |
|
UnixWare Controller with UnixWare 2.1.2 ....................................... |
6-8 |
Adding System Drives ..................................................................... |
6-10 |
To Primary Controller ............................................................... |
6-10 |
To Secondary Controller(s) ...................................................... |
6-10 |
Updating a Previously Installed Driver ..................................... |
6-10 |
Changing the Controller Configuration ............................................ |
6-11 |
Chapter 7 |
|
Solaris |
|
Overview ........................................................................................... |
7-1 |
Creating a Driver Diskette for Solaris ................................................ |
7-2 |
How to use the Mylex Supplemental Driver Diskette ......................... |
7-2 |
Installing Solaris Using the Solaris Device Configuration |
|
Assistant Diskette for a Primary Installation .................................... |
7-2 |
Installing Solaris Using the Mylex MDAC Supplemental |
|
Driver Diskette for a Secondary Installation .................................... |
7-4 |
Chapter 8 |
|
Linux |
|
Overview ........................................................................................... |
8-1 |
Installing the Disk Array Controller Drivers ........................................ |
8-1 |
Manual No. 775079 |
ix |
Appendix A
Creating PCI Driver Installation Diskettes
Introduction ........................................................................................ |
A-1 |
Creating Operating System Driver Diskettes ..................................... |
A-2 |
x |
PCI Disk Array Controller Drivers Manual |
Chapter 1
Introduction
Overview
This manual describes how to install and use the Mylex Disk Array Controller operating system drivers for Mylex PCI Disk Array Controllers.
Mylex Disk Array Controller drivers for all supported operating systems (except Linux) are delivered on a CD-ROM. Drivers for NetWare, Windows NT, and Windows 2000 are also delivered on diskettes.
Note
This manual assumes that the network administrator will be performing any of the installation procedures described herein.
NetWare, Windows NT, and Windows 2000
Use one of the following methods to obtain drivers for NetWare 4.2 / 5.x, Windows NT 4.0, or Windows 2000:
•Install drivers directly from the diskettes provided.
•Retrieve the appropriate driver image file from the CD-ROM and create a driver diskette from the DOS image file.
•Insert the CD-ROM into a system running Windows 95 / 98, Windows NT, or Windows 2000, then click on “Create Software Diskettes” from the RAID Management Software Installation menu. See Appendix A for details.
Manual No. 775079 |
1-1 |
Requirements
SCO OpenServer, UnixWare, and Solaris
Use the following method to obtain drivers for SCO OpenSever 5.0.5, UnixWare 7.x, 2.1.2 / 2.1.3, or Solaris 7 for x86:
•Insert the CD-ROM into a system running Windows 95 / 98, Windows NT, or Windows 2000, then click on “Create Software Diskettes” from the RAID Management Software Installation menu. See Appendix A for details.
Linux
In order to use any of the supported distributions of Linux, you will need to download the driver files from the appropriate web site (see Chapter 8 “Linux”).
Requirements
It is assumed that the hardware installation, the system configuration, and the disk array controller configuration are properly completed. If they are not, please refer to the appropriate Mylex disk array controller hardware installation guide and to the RAID EzAssist Configuration Utility User Reference Guide or RAID EzAssist Configuration Utility Quick Configuration Guide. Complete the required procedures described in those manuals before proceeding with installation of drivers discussed herein.
The person who will be performing the installation should have Supervisor or Administrator rights for the system onto which these software drivers will be installed.
It may also be necessary to prepare a DOS bootable floppy disk to be able to perform certain procedures described in this manual. Before starting, be sure to read through all applicable instructions to determine the specific requirements for each operating system to be supported.
1-2 |
PCI Disk Array Controller Drivers Manual |
Chapter 2
NetWare
N
2E
T
W
A
R
E
Overview
This chapter describes installation procedures and the functionality of the Mylex Disk Array Controller drivers for Novell NetWare. The software for the drivers is provided on the appropriate Software Kit distribution diskette and CD-ROM.
Mylex Disk Array Controller Driver Files for NetWare
All hardware installation, system configuration, and disk array controller configuration must be properly completed before proceeding with the NetWare driver installation. These basic installation procedures follow the Novell Installation manual, with only the few minor differences that are described in this section.
The subdirectory \netware on the DOS-formatted NT4/NW Drivers Software Kit diskette and on the CD-ROM contains the following:
MDAC.HAM: The driver to support Mylex Disk Array Controllers with NetWare.
MDAC.DDI: NetWare installation file for MDAC.HAM.
Tape, Disk, and CD-ROM Support
Tape drive support is available to the Mylex Disk Array Controller under NetWare by means of the NWTAPE.CDM. Most NetWare applications that communicate through ASPI on the server will work with the controller when the NWASPI.CDM module is loaded. Disk drive support is provided through the SCSIHD.CDM module.
Manual No. 775079 |
2-1 |
Installing the Mylex Disk Array Controller as the Primary NetWare 4.2 Controller
Similar to tape drive support, the controller also supports CD-ROM for use under NetWare. The SCSICD.CDM provides support to the CD-ROM application running on the server. A CD-ROM driver will also have to be loaded. These are included with the Novell NetWare releases.
Installing the Mylex Disk Array Controller as the Primary NetWare 4.2 Controller
If the Mylex Disk Array Controller will be the primary (bootable) controller, you must install the controller driver at the time of NetWare 4.2 installation.
Installing NetWare 4.2 Drivers
NetWare version 4.2 is available on CD-ROM. Drivers provided in the \DOS subdirectory of the NT4/NW Drivers Software Kit diskette (packaged with the Mylex Disk Array Controller) are required to install NetWare 4.2 from a CD-ROM drive connected to a Mylex Disk Array Controller.
The procedure below assumes that the CD-ROM drivers are available.
1.Boot the system from a newly created DOS boot drive, and then create (or edit) the CONFIG.SYS and AUTOEXEC.BAT files to include the drivers required for accessing the CD-ROM as a logical drive under DOS. The following example assigns the CD-ROM as drive D: under MS-DOS 6.00 or above. CONFIG.SYS contains the statements:
device = [pathname]\aspidac.sys
device = [pathname]\btcdrom.sys /D:[devicename]
AUTOEXEC.BAT contains the statement:
[pathname]\mscdex /v /m:10 /D:[devicename]
The device name is that of the specific CD-ROM drive (e.g., MSCD001).
2.Boot the system with the new CONFIG.SYS and AUTOEXEC.BAT, and make sure the NetWare CD-ROM files are accessible under DOS.
3.Follow the standard NetWare 4.2 upgrade or installation procedure, as described in the NetWare 4.2 documentation.
4.Insert the DOS-formatted NT4/NW Drivers Software Kit diskette into the floppy disk drive when the installation program prompts you to
2-2 |
PCI Disk Array Controller Drivers Manual |
NetWare
insert the vendor-supplied disk. The installation program will scan the diskette for all available drivers. Select the NetWare 4.2 driver from the list:
MDAC.HAM
Installing Peripherals Under NetWare 4.2
Non-disk peripheral devices, such as tape or CD-ROM drives, can be installed on any channel of the controller. Each disk or non-disk device will require a unique SCSI ID, different from any other device connected to the same channel.
Each device requires a driver module connecting it to the DAC adapter. These modules are best loaded in the STARTUP.NCF file before the MDAC.HAM driver.
The common devices and required modules are:
SCSI disk drives |
SCSIHD.CDM |
(including Mylex RAID |
|
system drives) |
|
SCSI CD-ROM |
SCSICD.CDM |
SCSI tape drive |
NWTAPE.CDM |
Magneto optical drive |
SCSIMO.CDM |
DLT tape drive |
DLTTAPE.CDM |
IDE CD-ROM |
IDECD.CDM |
IDE disk drive |
IDEHD.CDM |
ASPI compliant |
NWASPI.CDM |
applications such |
|
as GAM |
|
N
2E
T
W
A
R
E
Manual No. 775079 |
2-3 |
Installing the Mylex Disk Array Controller as the Primary NetWare 4.2 Controller
1.The appropriate drivers should be loaded before trying to access the non-disk devices. For example, to use NetWare's Sbackup utility, do the following:
:load mdac.ham
:load nwtape.cdm
:load tsa410
:load tapedai
:scan for new devices
:load sbackup
Except for the mdac.ham driver, .CDM or .NLM files are supplied by Novell. Refer to the Novell documentation for instructions on running
Sbackup.
2.Load the following drivers to use a CD-ROM under NetWare 4.2 (the NLMs aspicd and cdrom are supplied by Novell):
:load mdac.ham
:load scsicd.cdm
:load cdrom.nlm
:cd mount [volume name]
After the CD-ROM is mounted, the volume on the CD-ROM can be mapped from any workstation and accessed.
Installing the Mylex Disk Array Controller into an Existing NetWare 4.2 System
If NetWare 4.2 is already installed and you wish to add a Mylex Disk Array Controller later, the controller will be a secondary (non-bootable) controller. After installing the controller hardware and configuring a disk array, follow the procedure below to add the necessary controller drivers.
1.With NetWare Server 4.2 loaded and running, load the NetWare program INSTALL.NLM by typing the following at the console prompt:
: load install
and press <Enter>.
2. Choose “Driver Options” in the Installation Options menu.
2-4 |
PCI Disk Array Controller Drivers Manual |
NetWare
3.Choose “Configure disk and storage device drivers” in the Driver Options menu.
4.Choose “Select an additional driver” in the Additional Driver Actions menu.
NetWare scans for controllers that do not have drivers already loaded.
5.At the “Select a driver” box, press <Ins> to choose to install an unlisted driver.
6.Insert the DOS-formatted NT4/NW Drivers Software Kit diskette into the diskette drive.
7.Press <F3> to specify the path of the NetWare driver you’re about to install.
8.Change the path line to read:
A:\netware
and press <Enter>. NetWare scans for drivers on the floppy diskette in the specified path.
9.In the “Select a driver to install” box, select the appropriate driver for your controller:
MDAC.HAM | <Controller model number>
10.Select Yes at the confirmation box to install the driver.
11.Press <Enter> to select the default server boot path.
12.Select Yes to save a backup of the old or existing driver.
13.Press <Enter> to continue when you see the message that the old driver will be saved.
NetWare copies the file.
14.What you just backed up was the old or existing .DSK or .HAM file. Repeat Steps 12 and 13 for the .DDI file.
15.Select No to decline selection of an additional driver to install unless you are installing more than one Mylex controller at this time.
16.Exit INSTALL.NLM by pressing <Esc> three times, then selecting Yes at the “Exit Install?” box.
This concludes installation of the driver files needed to run your Mylex Disk Array Controller under NetWare 4.2.
N
2E
T
W
A
R
E
Manual No. 775079 |
2-5 |
Installing the Mylex Disk Array Controller as the Primary NetWare 5.0 Controller
Installing the Mylex Disk Array Controller as the Primary NetWare 5.0 Controller
If the Mylex Disk Array Controller will be the primary (bootable) controller, you must install the controller driver at the time of NetWare 5.0 installation.
If you choose to use the NetWare 5.0 bootable CD-ROM, please read the instructions in the section “NetWare 5.0 Bootable CD-ROM” on page 2-7, before continuing.
Installing NetWare 5.0 Drivers
NetWare version 5.0 is available on CD-ROM. Drivers provided in the \DOS subdirectory of the NT4/NW Drivers Software Kit diskette (packaged with the Mylex Disk Array Controller) are required to install NetWare 5.0 from a CD-ROM drive connected to a Mylex Disk Array Controller.
The procedure below assumes that the CD-ROM drivers are available.
1.Boot the system from a newly created DOS boot drive, and then create (or edit) the CONFIG.SYS and AUTOEXEC.BAT files to include the drivers required for accessing the CD-ROM as a logical drive under DOS. The following example assigns the CD-ROM as drive D: under MS-DOS 6.00 or above. CONFIG.SYS contains the statements:
device = [pathname]\aspidac.sys
device = [pathname]\btcdrom.sys /D:[devicename]
AUTOEXEC.BAT contains the statement:
[pathname]\mscdex /v /m:10 /D:[devicename]
The device name is that of the specific CD-ROM drive (e.g., MSCD001).
2.Boot the system with the new CONFIG.SYS and AUTOEXEC.BAT, and make sure the NetWare CD-ROM files are accessible under DOS.
3.Create a directory C:\NWUPDATE
• Copy MDAC.HAM and MDAC.DDI from the \NETWARE path.
Copy A:\Netware\MDAC.* C:\NWUPDATE
2-6 |
PCI Disk Array Controller Drivers Manual |
NetWare
4.Follow the standard NetWare 5.0 upgrade or installation procedure, as described in the NetWare 5.0 documentation.
• MDAC.HAM will be installed from the C:\NWUPDATE directory.
5.Return to the driver summary by pressing the arrow keys and select the option to continue.
6.NetWare 5.0 will continue the installation.
7.Watch for another status screen that displays the storage devices (i.e., SCSIHD.CDM and SCSICD.CDM) and the network drivers:
•Select Modify
•Select Storage Devices
•Press the <Insert> key
•Select NWASPI.CDM (this driver is required to load GAM)
•Press <Enter>
•Return to the driver summary by using the arrow keys.
NetWare 5.0 Bootable CD-ROM
In order to boot from the NetWare 5.0 CD-ROM, you must enable CD-ROM Boot Support in the BIOS setup program of the device that controls the CD-ROM drive.
If your bootable CD-ROM drive is connected to a Mylex controller, follow the steps below to enable CD-ROM boot support.
1.Insert the NetWare 5.0 CD-ROM.
2.Power on or reboot the system.
After the Mylex Controller BIOS banner comes up, you will see the following statement:
Press <ALT-M> for BIOS options
3.Press <ALT-M> immediately.
The BIOS options menu will be displayed.
N
2E
T
W
A
R
E
Manual No. 775079 |
2-7 |
Installing the Mylex Disk Array Controller as the Primary NetWare 5.0 Controller
Note
In order to enable the CD-ROM boot, the controller’s BIOS must be enabled.
4.If the controller’s BIOS is disabled, press <Enter> to enable the BIOS.
5.Use the arrow key to select “CD-ROM boot disabled” and press <Enter> to enable the CD-ROM boot.
6.Press <ESC>, then press any key. This will restart the system with the new settings.
The system will now boot from the NetWare 5.0 CD-ROM.
7.Return to the section “Installing NetWare 5.0 Drivers” and follow steps 4 through 7 to complete your driver installation.
Installing Peripherals Under NetWare 5.0
Non-disk peripheral devices, such as tape or CD-ROM drives, can be installed on any channel of the controller. Each disk or non-disk device will require a unique SCSI ID, different from any other device connected to the channel.
Each device requires a driver module connecting it to the DAC adapter. These modules are best loaded in the STARTUP.NCF file before the MDAC.HAM driver.
The common devices and required modules are:
SCSI disk drives |
SCSIHD.CDM |
(including Mylex |
|
RAID system drives) |
|
SCSI CD-ROM |
SCSICD.CDM |
SCSI tape drive |
NWTAPE.CDM |
Magneto optical drive |
SCSIMO.CDM |
DLT tape drive |
DLTTAPE.CDM |
IDE CD-ROM |
IDECD.CDM |
IDE disk drive |
IDEHD.CDM |
ASPI compliant |
NWASPI.CDM |
applications such |
|
as GAM |
|
2-8 |
PCI Disk Array Controller Drivers Manual |
NetWare
1.The appropriate drivers should be loaded before trying to access the non-disk devices.
2.Load the following drivers to use a CD-ROM under NetWare 5.0 (cdrom is supplied by Novell):
Note
mdac.ham and scsicd.cdm are usually loaded in the startup.ncf file.
:load mdac.ham
:load scsicd.cdm
:load cdrom
After the CD-ROM is mounted, the volume on the CD-ROM can be mapped from any workstation and accessed.
Installing the Mylex Disk Array Controller into an Existing NetWare 5.0 System
If NetWare 5.0 is already installed and you wish to add a Mylex Disk Array Controller later, the controller will be a secondary (non-bootable) controller. After installing the controller hardware and configuring a disk array, follow the procedure below to add the necessary controller drivers.
1.Copy NWASPI.CDM (for GAM support).
•Copy C:\NWSERVER\DRIVERS\NWASPI.CDM to the directory named, C:\NWSERVER.
•In the C:\NWSERVER\STARTUP.NCF file add LOAD NWASPI.CDM with the other LOAD XXXX.CDM
2.With NetWare Server 5.0 loaded and running, load the NetWare program by typing the following at the console prompt:
: load nwconfig and press <Enter>.
3.Choose “Driver Options” in the Installation Options menu.
4.Choose “Configure disk and storage device drivers” in the Driver Options menu.
5.Choose “Select an additional driver” in the Additional Driver Actions menu.
N
2E
T
W
A
R
E
Manual No. 775079 |
2-9 |
Installing the Mylex Disk Array Controller as the Primary NetWare 5.0 Controller
NetWare scans for controllers that do not have drivers already loaded.
6.At the “Select a driver” box, press <Ins> to choose to install an unlisted driver.
7.Insert the NT4/NW Drivers Software Kit diskette into the diskette drive.
8.Press <F3> to specify the path of the NetWare driver you’re about to install.
9.Change the path line to read:
A:\netware
and press <Enter>. NetWare scans for drivers on the floppy diskette in the specified path.
10.In the “Select a driver to install” box, select the appropriate driver for your controller:
MDAC.HAM | Mylex Disk Array Controller <model number>
11.Select Yes at the confirmation box to install the driver.
12.Press <Enter> to select the default server boot path.
13.Select No to save a backup of the old or existing driver.
14.Select No to decline selection of an additional driver to install unless you are installing more than one controller at this time.
15.Exit INSTALL.NLM by pressing <Esc> three times, then selecting Yes at the “Exit Install?” box.
This concludes installation of the driver files needed to run your Mylex Disk Array Controller under NetWare 5.0.
2-10 |
PCI Disk Array Controller Drivers Manual |
Chapter 3
Windows NT
Overview
This chapter describes installation procedures and the functionality of the Mylex Disk Array Controller drivers for Microsoft Windows NT 4.0 with SP4 or SP5. The software is provided on the appropriate Software Kit distribution diskette and CD-ROM.
This chapter assumes that the network administrator for this site will be performing these installation procedures.
Mylex Disk Array Controller Driver Files for Windows NT
All hardware installation, system configuration, and disk array controller configuration must be properly completed before proceeding with the Windows NT driver installation. These basic installation procedures follow the Windows NT Installation manual, with the differences that are described in this chapter.
The root directory A:\ on the NT4/NW Drivers Software Kit diskette contains the following:
TXTSETUP.OEM |
Setup text file (required in root directory) needed for |
|
Windows NT installation. |
DISK1 |
Diskette identifier file. |
The subdirectory \NT4 on the NT4/NW Drivers Software Kit diskette contains the following:
DAC960NT.SYS Windows NT controller driver file for DAC960P Series, AcceleRAID 150/200/250, and DAC1164P
DAC960NT.INF Setup file for DAC960NT.SYS
W
3 I
N
N
T
Manual No. 775079 |
3-1 |
Overview
DAC2NT4.SYS Windows NT Controller driver file for AcceleRAID 160/170/170LP/352, and eXtremeRAID 2000/3000
DAC2NT4.INF Setup file for DAC2NT4.SYS
README.NT (Optional) Last minute information on Windows NT Installation
The subdirectory \DISK on the NT4/NW Drivers Software Kit diskette contains the following:
MACDISK.SYS Mylex Accelerated Driver for Windows NT
MACDISK.INF Setup file for MACDISK.SYS
3-2 |
PCI Disk Array Controller Drivers Manual |
Windows NT
Installing the Mylex Disk Array Controller as the Primary Windows NT 4.0 Controller
If the Mylex Disk Array Controller will be the primary (bootable) controller, you must install the controller driver at the time of Windows NT 4.0 installation.
Before proceeding you should have already carried out the following steps:
•Installed the Mylex Disk Array Controller hardware, connected the disk drives to the controller and to each other, set drive SCSI IDs, and terminated the SCSI bus following the instructions in your Mylex Disk Array Controller hardware installation guide.
•Used the Mylex RAID EzAssist Configuration Utility to create a drive configuration and initialized the drives for use following the instructions in your Mylex RAID EzAssist Configuration Utility manual.
To install the controller driver during Windows NT 4.0 installation:
1.Boot the system with the Windows NT 4.0 setup diskette #1.
2.Insert setup diskette #2 when prompted and press <Enter>.
3.Press <Enter> again when prompted.
4.Select Custom Setup in the Windows NT Setup screen.
5.Next, choose S to skip the automatic detection scan.
6.Choose S to specify an additional device.
7.Choose Other in the list of supported adapters displayed and press
<Enter>.
8.When prompted for the Manufacturer’s supplied hardware support disk, insert your NT4/NW Drivers Software Kit diskette into the floppy disk drive and press <Enter>.
W
3 I
N
N
T
Manual No. 775079 |
3-3 |
Installing the Mylex Disk Array Controller as the Primary Windows NT 4.0 Controller
9.Select the appropriate controller from the list of controllers displayed on this screen and press <Enter>.
10.If you have drivers to install for other controllers (for example, an on-board SCSI or IDE controller to run other devices such as a CDROM drive, etc.), repeat Step 6 and Step 7. Then when prompted, insert the manufacturer’s supplied hardware support disk, press <Enter>, and select the appropriate driver from the list.
If you have no other drivers to install, or when you have finished installing other drivers, simply press <Enter> to continue installation.
11.Insert Windows NT 4.0 setup diskette #3 when prompted.
12.Follow the on-screen instructions to continue Windows NT 4.0 installation, inserting the Windows NT CD-ROM into the CD-ROM drive when prompted. Press <Enter> and continue with the next few Windows NT 4.0 installation screens.
13.When prompted again for the “MDAC Software Kit” diskette, insert the NT4/NW Drivers Software Kit diskette into the floppy disk drive and press <Enter>.
If you installed other drivers from other diskettes, you will be asked to reinsert those diskettes as well.
This concludes Mylex Disk Array Controller driver installation for Windows NT 4.0. Follow the on-screen instructions to complete your installation of the Windows NT 4.0 operating system.
3-4 |
PCI Disk Array Controller Drivers Manual |
Windows NT
Installing the Mylex Disk Array Controller into an Existing Windows NT 4.0 System
If Windows NT 4.0 is already installed and you wish to add a Mylex Disk Array Controller later, the controller will be a secondary (non-bootable) controller. After installing the controller hardware and configuring a disk array, follow the procedure below to add the necessary controller drivers.
1. Make sure Windows NT 4.0 is up and running.
2.Click Start, and select Settings->Control Panel within the Start menu (Figure 3-1).
Figure 3-1. Open the Windows NT 4.0 Control Panel
3.From the Control Panel window, double-click the SCSI Adapters icon (Figure 3-2).
W
3 I
N
N
T
Manual No. 775079 |
3-5 |
Installing the Mylex Disk Array Controller into an Existing Windows NT 4.0 System
Figure 3-2. Control Panel - SCSI Adapters
4.In the SCSI Adapters box, click the Drivers tab to bring the Drivers page to the foreground (Figure 3-3).
Figure 3-3. SCSI Adapters
3-6 |
PCI Disk Array Controller Drivers Manual |
Loading...