This monitor is manufactured and tested on a ground principle that a user's safety comes first.
However, improper use or installation may cause damage to the monitor as well as to the user.
Carefully go over the following WARNINGS before installing and keep this guide handy.
WARNINGS:
This monitor should be operated only at the correct power sources indicated on the label on
!
the rear end of the monitor. If you're unsure of the power supply in your residence, consult
your local dealer or power company.
Use only the special power adapter that comes with this monitor for power input.
!
Do not try to repair the monitor your self as it contains no user-serviceable parts. This
!
monitor should only be repaired by a qualified technician.
Do not remove the monitor cabinet. There is high-voltage parts inside that may cause
!
electric shock to human bodies, even when the power cord is unplugged.
Stop using the monitor if the cabinet is damaged. Have it checked by a service technacian.
!
Put your monitor only in a clean, dry environment. If it gets wet, unplug the power cable
!
immediately and consult your service technician.
Always unplug the monitor before cleaning it. Clean the cabinet with a clean, dry cloth.
!
Apply non-ammonia based cleaner onto the cloth, not directly onto the glass screen.
Keep the monitor away from magnetic objects, motors, TV sets, and transformer.
!
Do not place heavy objects on the monitor or power cord.
!
1.2. PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety visual inspections and the
protection afforded by them cannot necessarily be obtained by using replacement components
rated for higher voltages, wattage, etc. Before replacing any of these components read the parts
list in this manual carefully. The use of substitute replacement parts which do not have the same
safety characteristics as specified in the parts list may create shock, fire, or other hazards.
1.3. SERVICE NOTES
1. When replacing parts or circuit boards, clamp the lead wires around terminals before
soldering.
2. When replacing a high wattage resistor (more than 1W of metal oxide film resistor) in circuit
board, keep the resistor about 5mm away from circuit board.
3. Keep wires away from high voltage, high temperature components and sharp edges.
4. Keep wires in their original position so as to reduce interference.
5. Usage of this product please refer to also user's manual.
AL512/AL513 Service Manual
2. SERVICE TOOL & EQUIPMENT REQUIRED
1. SIGNAL GEN.
2. MULTIMETER
3. OSCILLOSCOPE
4. SCREW DRIVER
5. IRON
6. ABSORBER
7. SOLDER
8. DUMMY LOAD (5ohm/200W)
3. SPECIFICATIONS
3.1. PRODUCT SPECIFICATIONS
LCD Panel 15.0" TFT
Power Management Energy Star compliant V ESA
DPMS compatible
< 3W
TIMING 720×400@70Hz 640×480@60Hz 640×480@67Hz 640×480@75Hz 800×600@56Hz
Pixel Rate 28.322MHz 25.175MHz 30.240MHz 31.500MHz 36.000MHz
H TOTAL 31.778us 31.778us 28.571us 26.667us 28.444us
H DISPLAY 25.422us 25.422us 21.164us 20.317us 22.222us
H B-Porch 1.907us 1.907us 3.175us 3.810us 3.556us
H Width 3.813us 3.813us 2.116us 2.032us 2.000us
H Border 0.318us 0.318us 0.000us 0.000us 0.000us
V TOTAL 14.268ms 16.683ms 15.000ms 13.334ms 17.778ms
V DISPLAY 12.711ms 15.253ms 13.714ms 12.800ms 17.066ms
V B-Porch 1.112ms 1.049ms 1.114ms 0.427ms 0.626ms
Vs Width 0.064ms 0.064ms 0.086ms 0.080ms 0.057ms
V Border 0.222ms 0.254ms 0.000ms 0.000ms 0.000ms
H/V Sync -/+ -/- -/- -/- +/+
Interlace No. No. No. No. No.
ITEM 6 7 8 9 10
TIMING 800×600@60Hz 800×600@72Hz 800×600@75Hz
Pixel Rate 40.000MHz 50.000MHz 48.500MHz 57.280MHz 65.000MHz
H TOTAL 26.400us 20.800us 21.333us 20.112us 20.677us
H DISPLAY 20.000us 16.000us 16.162us 14.525us 15.754us
H B-Porch 2.200us 1.280us 3.232us 3.771us 2.462us
H Width 3.200us 2.400us 1.616us 1.118us 2.092us
H Border 0.000us 0.000us 0.000us 0.000us 0.000us
V TOTAL 16.579ms 13.853ms 13.333ms 13.417ms 16.666ms
V DISPLAY 15.840ms 12.480ms 12.800ms 12.552ms 15.880ms
V B-Porch 0.607ms 0.478ms 0.448ms 0.784ms 0.600ms
Vs Width 0.106ms 0.125ms 0.064ms 0.060ms 0.124ms
V Border 0.000ms 0.000ms 0.000ms 0.00ms 0.000ms
H/V Sync +/+ +/+ +/+ -/- -/Interlace No. No. No. No. No.
832×624@74.5Hz 1024×768@60Hz
AL512/AL513 Service Manual
ITEM 11 12 13 14 15
TIMING
Pixel Rate 75.000MHz 78.750MHz
H TOTAL 17.707us 16.660us
H DISPLAY 13.653us 13.003us
H B-Porch 1.920us 2.235us
H Width 1.813us 1.219us
H Border 0.000us 0.000us
V TOTAL 14.272ms 13.328ms
V DISPLAY 13.599ms 12.795ms
V B-Porch 0.513ms 0.466ms
Vs Width 0.106ms 0.050ms
V Border 0.000ms 0.000ms
H/V Sync -/- +/+
Interlace No. No.
3.3. D-SUB CONNECTOR
D-SUB 15 PIN CONNECTOR
1024×768@70Hz 1024×768@75Hz
12345
678910
11 12 13 14 15
SIGNAL LEVEL
CONNECTOR SIGNAL DESCRIPTION
R RED 0.7vp-p(VIDEO)
G GREEN 0.7vp-p(VIDEO)
B BLUE 0.7vp-p(VIDEO)
H H/SYNC TTL positive or negative
V V/SYNC TTL positive or negative
SDA DDC1/2B TTL
SCL DDC1/2B TTL
1.R 6.GND 11.NC
2.G 7.GND 12.SDA
3.B 8.GND 13.H-SYNC
4.NC 9. +5V 14.V-SYNC
5.GND 10.GND 15.SCL
4.1. EXPLODED VIEW
FIG.1
(AL512/AL513)
2C04
FIG.3
X2
FIG.3
5B07
1F03
1F04
1F02
1F01
1F05
5B05
1F06
5B06
1F05
1F06
W601
U901
1F11
1F09
1F30
X4
X2
1F08
V901
1F10
X3
KEYPAD PCB ASS'Y
MAIN PCB ASS'Y
NOTE.2
1F07
X2
1F26
FIG.4
1F13
1F09 X4
1F14
P983
1F21
X2
1F10
1F15
1F16
X9
FIG.2
X4
2C01
X4
FIG.5
1F17
2C05
1F18
X4
2C09
1F19
2C06
X2
2C05
FIG.1
2C03
2C09
X2
2C07
2C08
FIG.2
5B01
X3
5B08
MPRⅡTCO99
5B08
X4
5B15
POWER PCB ASS'Y
9H01
5B02
5B09
5B04
X4
FIG.4
1F25 X2
AUDIO-IN PCB ASS'Y
1F22
1F20
P984
1F23
I/O CABLE
1F24 X2
1F12
NOTE.1FIG.5
2C02
AUDIO PCB ASS'Y
9H61
9S61
X2
9S03
X4
9R81
9S02
9S01
9H01
AL512/AL513 Service Manual
4.2. EXPLODED VIEW PARTS LIST
Ref. No. Source Part No. DESCRIPTION SPECIFICATION Q‘TY REMARK
1F01 2024263501 FRONT BEZEL AL512 ABS 94V0 860027 1
1F01 2024263503 FRONT BEZEL AL513 ABS+PC 94V0 860027 1 TCO99
1F02 2044263101 FUNCTION KEY AL512 ABS 94HB PS-7604B 1
1F03 2054254101 ORNAMENT DOOR PANEL ABS 94HB 860027 1 AL512
1F03 2054254001 ORNAMENT DOOR PANEL ABS 94HB 860027 1 AL513
1F04 2053752701 LED INDIC.-PWR JT166AL LED LENS PMMA 94HB 1
1F05 2061252400 SPONGE 36X23X3t EVA 2 AL512 Only
1F06 2084730082 SCREW,BND T+ M3X8(BND T+) 2 AL512 Only