Table of Contents |
|
Precautions ....................................................................................................... |
2 |
Special notes on LCD monitors........................................................................ |
2 |
Package contents ............................................................................................. |
3 |
Installation instructions ................................................................................... |
3 |
Assembling the monitor .......................................................................................... |
3 |
Adjusting the viewing angle ..................................................................................... |
4 |
Connecting the devices ........................................................................................... |
6 |
Switching the power .............................................................................................. |
6 |
Adjusting display settings................................................................................ |
7 |
External controls................................................................................................... |
7 |
OSD options...................................................................................................... |
8 |
OSD menu .......................................................................................................... |
8 |
Troubleshooting............................................................................................. |
11 |
General specifications.................................................................................... |
12 |
1
Precautions
The monitor may be damaged if placed too near a source of heat. Be aware of the location of radiators, cookers, open fires, etc.
Do not cover the slots and openings on the back or top of the cabinet, as the monitor requires ventilation. The monitor should be located in a well-ventilated room to prevent the possibility of overheating.
Do not allow sharp objects such as knives, pens, or pencils near the screen. If such objects touch the screen, the LCD panel may be permanently scratched.
When cleaning this monitor, disconnect it from the electrical socket to avoid any danger of electrocution. A soft, lint-free cloth should be used to clean the outside of the monitor. A cloth slightly moistened with a mild detergent solution will clean stubborn stains. Keep liquids away from the display screen, including sprays. Do not spray liquid directly on the monitor — it is best to lightly spray on to a cloth and then gently wipe the monitor. If liquid gets inside the monitor it can cause electrical shock and/or damage to the unit.
If you encounter a problem, please check the "Troubleshooting" section first. If this does not resolve the problem, do not attempt to repair the monitor by yourself. Opening or removing covers can lead to injury or death through electrocution or other hazards. Please contact a qualified engineer if the troubleshooting section does not solve your problem.
Recycling information
Acer cares very much about protecting the environment, and firmly believes that the environment will be healthier if appropriate measures are taken to treat and recycle industrial technology products.
Such products contain hazardous, poisonous substances that can seriously harm the environment. Furthermore, industrial technology products contain materials that can be recycled and re-integrated. We strongly encourage you to recycle this IT product through the appropriate agency by reviewing the information provided below:
United States: http://www.ciwmb.ca.gov/electronics/act2003/Recovery/Approved/
Asia: http://recycle.epa.gov.tw/public/public4_2.htm
Europe: EL-Kretsen: http://www.el-kretsen.se/
EL-retur: http://www.elretur.no/
SWICO: http://swico.one.webbuild.ch/
Special notes on LCD monitors
The following symptoms are normal for LCD monitors and do not indicate a problem with the device:
•Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the power switch and then turn it on again to make the flicker disappear.
•You may find slightly uneven brightness on the screen depending on the desktop pattern you use.
•The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.01% or less (caused by a missing pixel or a pixel that is always lit).
•When the same image is displayed for hours on end, its afterimage may remain after switching to a new image. When this happens, the screen will recover slowly by changing the image. Turning the LCD monitor off for several hours will also correct this problem.
2
Package contents
LCD monitor |
Power cord |
Audio cable |
VGA cable |
DVI cable |
User's Guide (CD) |
Quick Start Guide |
Installation instructions
Assembling the monitor
1.Position the monitor on top of the base.
2.Connect the base into the neck of the monitor along the track.
Detaching the monitor
If you need to detach the monitor for repackaging, the monitor and base must be separated in order to fit in the carton.
To detach the monitor:
1.Unplug the AC power cord to make sure the power is off.
2.Pull the 4 hooks on the bottom side of the base and hold.
3.Separate the monitor and base.
Important
When separating the monitor and base, find a clean, flat surface to place the monitor on and place a clean dry cloth under the monitor to protect it further. After removing the monitor from the base, pull the monitor slightly up and away from the base and place it on the cloth.
3
Adjusting the viewing angle
The viewing angle of the monitor ranges from -5 – 20°.
Adjusting the viewing angle (Only AL1723 h/AL1723 r)
Your monitor features a multi-adjustable stand that will enable it move 100mm up/down (height adjustment), 25 degree forward/backward (tilt adjustment), 60 degree side/side (swivel adjustment). To make an adjustment, grasp the monitor with both hands on the right and left edge of the casing and move it to the desired position.
Do not perform a pulling or plugging action when the display is under slanting status to prevent the display from ejecting.
Pull out the pin from the display support frame as per the figure and then adjust the height. Note that upon pulling out the pin, erect the machine on the table to prevent the top part of the display from ejecting.
4