PCI 1M PhoneLine
Network Adapter
Quick installation Guide
M73-APO01-120
REGULATORY STATEMENTS
Part15, Class B
This device complies with Part 15 of FCC rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interface, and
2. This device must accept any interface received,
including interface that may cause undesired
operation. This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy, and if not installed and used in
accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be
determined by turning off and on, the user is
encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the distance between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
Changes or modifications not expressly
*
approved by party responsible for compliance
could void the user the user authority to
operate the equipment.
FCC Part 68 Registration
This device complies with FCC Part 68 rules, and the use of
this device is subject to the following restrictions:
1. The FCC has established rules which permit this device
to be directly connected to the telephone network.
Standardized jacks are used for these connections. This
equipment should not be used on party lines or coin
phones.
2. If this device is malfunctioning, it may also be causing
harm to the telephone network; this device should be
disconnected until the source of the problem can be
determined and until repair has been made. If this is not
done, the telephone company may temporarily
disconnect service.
3. The telephone company may make changes in it's
facilities, equipment, operation and procedures; if such
changes affect the compatibility or use of this device,
the telephone company is required to give adequate
notice of the situation with the FCC.
4. If the telephone company requests information on what
equipment is connected to their lines, inform them of:
a. The telephone number to which this unit is connected.
b. The Ringer Equivalence Number (REN).
c. The USOC jack required.
d. The FCC Registration number.
Items (b) and (d) are indicated on the label. The Ringer
Equivalence Number (REN) is used to determine how many
devices can be connected to your telephone line. In most
areas, the sum of the REN's of all the devices on any one line
should not exceed 5.0. If too many devices are attached, they
may not ring properly.
INTRODUCTIONS
The PCI 1M PhoneLine Network Adapter
enables the instant connectivity to multiple PCs
over a home's existing telephone lines.
You can share network-enabled printers, transfer
files between computers, play network games,
and more- no switches, hubs, or even any
additional cables is needed. The network runs on
standard home-grade telephone wires just like
the ones you use everyday. Plus, it doesn’t
interfere with your normal phone use.
Features
• Connects to a network using your existing
telephone line -- No additional hubs or
network cables needed
• 1Mbps transfer rate over telephone lines
• HomePNA 1.0, 1.1 compliant
Specifications
Network Specification
• Media: Home-grade phone line up to 500
feet
• Nodes Supported: 25 nodes maximum
• Frequency Range: 5.5M to 9.5M Hz
• Topology: Daisy chain
Host Interface
• Host Interface: 32bit 33Mhz PCI 2.0, 2.1,
2.2 compliant.
• PC98, PC99, and NetPC Compliant
Driver Supported
• Windows NT 4.0
• Windows 95 all version
- 1 -
• Windows 98 all version
• Windows 2000 ready
HARDWARE INSTALLATION
Before you begin, make sure you turn off all
power to your computer.
1. Remove the chassis cover of your computer.
2. Align the contact edge of the PCI 1M
PhoneLine Network Adapter
connector of any free PCI Bus Master
expansion slot. Push firmly and slowly until
it is fully seated in the connector.
3. Screw the PCI 1M PhoneLine Network
Adapter
to the computer chassis with the
provided screws.
4. Replace the computer’s chassis cover.
5. Turn on your computer.
Connecting Telephone Cabling
1. Attach one end of the telephone wire to the
PCI 1M PhoneLine Network Adapter’s RJ11 telephone port.
2. Connect the other end of the wire into a
telephone jack in your wall.
toward the
- 2 -
SOFTWARE INSTALLATION
Once your PCI 1M PhoneLine Network Adapter
has been successfully installed into the computer,
turn on your computer and the system will
automatically detect the new hardware. Insert the
driver diskette for the PCI 1M PhoneLine
Network Adapter into the floppy disk drive.
To efficiently help you to setup the proper driver
for your PCI 1M PhoneLine Network Adapter,
an on-line documentation named
README.TXT was provided in the
folder/subdirectory corresponding to the
operating system you are working with. For
example, if your are working with Windows 98,
go to the WIN98 folder, click README.TXT.
- 3 -
Loading...