Abit KV7-V, KV7 User Manual
KV7 Series
(KV7, KV7-V)
AMD Athlon XP System Board
Socket 462
User’s Manual
4200-0380-12
Rev. 1.01
Copyright and Warranty Notice
The information in this document is subject to change without notice and does not
represent a commitment on part of the vendor, who assumes no liability or
responsibility for any errors that may appear in this manual.
No warranty or representation, either expressed or implied, is made with respect to the
quality, accuracy or fitness for any particular part of this document. In no event shall
the manufacturer be liable for direct, indirect, special, incidental or consequential
damages arising from any defect or error in this manual or product.
Product names appearing in this manual are for identification purpose only and
trademarks and product names or brand names appearing in this document are the
property of their respective owners.
This document contains materials protected under International Copyright Laws. All
rights reserved. No part of this manual may be reproduced, transmitted or transcribed
without the expressed written permission of the manufacturer and authors of this
manual.
If you do not properly set the motherboard settings, causing the motherboard to
malfunction or fail, we cannot guarantee any responsibility.
KV7 Series
Table of Contents
Chapter 1. Introduction ............................................................................ 1-1
1-1. Features & Specifications ........................................................................1-1
1-2. Layout Diagram (KV7)............................................................................1-3
1-3. Layout Diagram (KV7-V)........................................................................1-4
Chapter 2. Hardware Setup ...................................................................... 2-1
2-1. Install The Motherboard...........................................................................2-1
2-2. Install CPU and Heatsink.........................................................................2-1
2-3. Install System Memory ............................................................................2-3
2-4. Connectors, Headers and Switches ..........................................................2-4
(1). ATX Power Input Connectors........................................................2-4
(2). FAN Connectors.............................................................................2-5
(3). CMOS Memory Clearing Header ..................................................2-6
(4). S2K Mode Select Header (For KV7 only) ..................................... 2-7
(5). Wake-up Header.............................................................................2-8
(6). Front Panel Switches & Indicators Headers ..................................2-9
(7). Additional USB Port Headers......................................................2-10
(8). Front Panel Audio Connection Header ........................................ 2-11
(9). Internal Audio Connectors ...........................................................2-13
(10). Accelerated Graphics Port Slot....................................................2-13
(11). Floppy Disk Drive Connector......................................................2-14
(12). IDE Connectors............................................................................2-15
(13). Serial ATA Connectors.................................................................2-16
(14). Back Panel Connectors ................................................................2-17
Chapter 3. BIOS Setup.............................................................................3-1
3-1. SoftMenu Setup........................................................................................3-2
3-2. Standard CMOS Features.........................................................................3-4
3-3. Advanced BIOS Features......................................................................... 3-7
3-4. Advanced Chipset Features......................................................................3-9
3-5. Integrated Peripherals ............................................................................3-14
3-6. Power Management Setup .....................................................................3-17
3-7. PnP/PCI Configurations.........................................................................3-21
3-8. PC Health Status ....................................................................................3-23
User’s Manual
3-9. Load Fail-Safe Defaults .........................................................................3-24
3-10. Load Optimized Defaults.......................................................................3-24
3-11. Set Password ..........................................................................................3-24
3-12. Save & Exit Setup..................................................................................3-24
3-13. Exit Without Saving...............................................................................3-24
Appendix A. Install VIA 4-in-1 Driver ................................................................. A-1
Appendix B. Install Audio Driver ......................................................................... B-1
Appendix C. Install LAN Driver ........................................................................... C-1
Appendix D. Install VIA USB 2.0 Driver .............................................................D-1
Appendix E. Install Serial ATA RAID Driver...................................................... E-1
Appendix F. ABIT EQ (The Hardware Doctor Utility) ....................................... F-1
Appendix G. FlashMenu (BIOS Update Utility) .................................................. G-1
Appendix H. Troubleshooting (Need Assistance?)...............................................H-1
Appendix I. How to Get Technical Support ......................................................... I-1
KV7 Series
Introduction 1-1
Chapter 1. Introduction
1-1. Features & Specifications
1. CPU
• Supports AMD AthlonXP/Sempron Socket 462, 266/333/400MHz FSB Processors
2. Chipset (VIA KT600 and VT8237)
• Supports Hi-Speed Universal Serial Bus (USB 2.0)
• Supports Advanced Configuration and Power Interface (ACPI)
• Accelerated Graphics Port connector supports AGP 8X/4X Interface (0.8V/1.5V)
3. Memory
• 3x 184-pin DIMM sockets
• Supports 2 DIMM Un-buffered DDR 333/400 (Max. 2GB)
• Supports 3 DIMM Un-buffered DDR 266 (Max. 3GB)
4. ABIT Engineered
• ABIT SoftMenu™ Technology
• ABIT FanEQ
• ABIT EQ
• ABIT Audio EQ
• ABIT FlashMenu
5. Serial ATA 150 RAID
• 2 channels of Serial ATA 150MB/s data transfer rate with RAID function (0/1) via South
Bridge
6. LAN
• Onboard 10/100M PCI Fast Ethernet Controller
7. Audio
• Onboard 6-Channel AC 97 CODEC
• Professional digital audio interface supports auto jack sensing and optical S/PDIF Out (KV7)
8. Internal I/O Connectors
• 1x AGP slot
• 5x PCI slots
• 1x floppy port supports up to 2.88MB
• 2x Ultra ATA 133/100/66/33 connectors
• 2x Serial ATA 150 connectors
• 2x USB 2.0 headers
• 1x CD-IN, 1x AUX-IN header
™
Technology
™
Technology
™
™
Technology
Technology
User’s Manual
1-2 Chapter 1
9. Back Panel I/O
• 1x PS/2 keyboard, 1x PS/2 mouse
• 1x Serial port connector, 1x Parallel port connector
• 1x AUDIO1 connector (Rear-Left / Rear-Right, Center/Subwoofer, S/PDIF Output, Mic-In,
Line-In, Front-Left/Front-Right) (KV7)
• 1x AUDIO2 connector (Mic-In, Line-In, Line-Out) (KV7-V)
• 4x USB 2.0, 1x RJ-45 LAN Connector
10. Miscellaneous
• ATX form factor (305x195mm)
Specifications and information contained herein are subject to change without notice.
KV7 Series
Introduction 1-3
1-2. Layout Diagram (KV7)
User’s Manual
1-4 Chapter 1
1-3. Layout Diagram (KV7-V)
KV7 Series
Hardware Setup 2-1
Chapter 2. Hardware Setup
Before the Installation: Turn off the power supply switch (fully turn off the +5V standby power), or
disconnect the power cord before installing or unplugging any connectors or add-on cards. Failing to do
so may cause the motherboard components or add-on cards to malfunction or damaged.
2-1. Install The Motherboard
Most computer chassis have a base with many mounting holes to allow motherboard to be securely
attached on and at the same time, prevented from short circuits. There are two ways to attach the
motherboard to the chassis base:
1. use with studs
2. or use with spacers
In principle, the best way to attach the board is to
use with studs. Only if you are unable to do this
should you attach the board with spacers. Line up
the holes on the board with the mounting holes on
the chassis. If the holes line up and there are
screw holes, you can attach the board with studs.
If the holes line up and there are only slots, you
can only attach with spacers. Take the tip of the
spacers and insert them into the slots. After doing
this to all the slots, you can slide the board into
position aligned with slots. After the board has been positioned, check to make sure everything is OK
before putting the chassis back on.
ATTENTION: To prevent shorting the PCB circuit, please REMOVE the metal studs or spacers if they
are already fastened on the chassis base and are without mounting-holes on the motherboard to align with.
2-2. Install CPU and Heatsink
Note
• Installing a heatsink and cooling fan is necessary for heat to dissipate from your processor.
Failing to install these items may result in overheating and processor damage.
• The AMD Socket A processor will produce a lot of heat while operating, so you need to use a
large heat sink that is especially designed for the AMD socket A processor. Otherwise, it may
result in overheating and processor damage.
• If your processor fan and its power cable are not installed properly, never plug the ATX power
cable into the motherboard. This can prevent possible processor damage.
• Please refer to your processor installation manual or other documentation with your processor
for detailed installation instructions.
User’s Manual
2-2 Chapter 2
This motherboard provides a ZIF (Zero Insertion
Force) Socket 462 to install AMD Socket A CPU.
The CPU you bought should have a kit of
heatsink and cooling fan along with. If that’s not
the case, buy one specially designed for Socket A.
Please refer to the figure shown here to install
CPU and heatsink. (For reference only. Your
Heatsink & Fan Assembly may not be exactly the
same as this one.)
1. Locate the Socket 462 on this motherboard.
Pull the CPU release lever sideways to
unlatch and then raise it all the way up.
2. Align the CPU notch to the socket notch for
CPU. Drop the processor with its pin side
down into the CPU socket. Do not use extra
force to insert CPU; it only fit in one
direction. Close the CPU release lever.
3. Remove the plastic film adhesive on the
heatsink. Make sure the stepped portion of
the heatsink is facing toward the end of the
socket that reads “Socket 462”. Put the
heatsink faces down onto the processor until
it covers the processor completely.
4. Push down the short end of the retaining clip
first to lock up with the center lug at the
bottom of the socket.
5. Use a screwdriver to insert into the slot at the
long end of the retaining clip. Push the clip
downward to lock up with the center lug at
the top of the socket. The heatsink & fan
assembly is now firmly attached on the CPU
socket.
6. Attach the fan connector of Heatsink & Fan
Assembly with the fan connector on the
motherboard.
ATTENTION: Do not forget to set the correct
bus frequency and multiple for your processor.
KV7 Series
Hardware Setup 2-3
2-3. Install System Memory
This motherboard provides 3 184-pin DDR DIMM sites for memory expansion available from minimum
128MB to maximum 3GB.
Table 2-1. Valid Memory Configurations
Bank Memory Module Total Memory
Bank 0, 1 (DIMM1) 128, 256, 512MB, 1GB 128MB ~ 1GB
Bank 2, 3 (DIMM2) 128, 256, 512MB, 1GB 128MB ~ 1GB
Bank 4, 5 (DIMM3) 128, 256, 512MB, 1GB 128MB ~ 1GB
Total System Memory for Un-buffered DDR 266 DIMM 128MB ~ 3GB
Total System Memory for Un-buffered DDR 333/400 DIMM 128MB ~ 2GB
NOTE: It is necessary to install one DIMM module at least from memory slot DIMM1.
Power off the computer and unplug the AC power cord before installing or removing memory modules.
1. Locate the DIMM slot on the board.
2. Hold two edges of the DIMM module
carefully, keep away of touching its
connectors.
3. Align the notch key on the module with the
rib on the slot.
4. Firmly press the module into the slots until
the ejector tabs at both sides of the slot
automatically snaps into the mounting notch.
Do not force the DIMM module in with extra
force as the DIMM module only fit in one direction.
5. To remove the DIMM modules, push the two ejector tabs on the slot outward simultaneously, and
then pull out the DIMM module.
ATTENTION: Static electricity can damage the electronic components of the computer or optional
boards. Before starting these procedures, ensure that you are discharged of static electricity by touching a
grounded metal object briefly.
User’s Manual
2-4 Chapter 2
2-4. Connectors, Headers and Switches
Here we will show you all of the connectors, headers and switches, and how to connect them. Please read
the entire section for necessary information before attempting to finish all the hardware installation inside
the computer chassis. A complete enlarged layout diagram is shown in Chapter 1 for all the position of
connectors and headers on the board that you may refer to.
WARNING: Always power off the computer and unplug the AC power cord before adding or removing
any peripheral or component. Failing to so may cause severe damage to your motherboard and/or
peripherals. Plug in the AC power cord only after you have carefully checked everything.
ATX Power Input Connectors
(1).
This motherboard provides two power connectors to connect to an ATX12V power supply with 300W,
20A +5VDC, and 720mA +5VSB capacity at least.
KV7 Series
Hardware Setup 2-5
(2). FAN Connectors
These 3-pin connectors each provide power to the cooling fans installed in your system.
The CPU must be kept cool by using a powerful fan with heatsink. The system is capable of monitoring
the speed of the CPU fan.
• CPUFAN1: CPU Fan
• NBFAN1: Chipset Fan
• SYSFAN1: System Fan
• AUXFAN1, AUXFAN2: Auxiliary Fan
WARNING: These fan connectors are not jumpers. DO NOT place jumper caps on these connectors.
KV7: KV7-V:
User’s Manual
2-6 Chapter 2
(3). CMOS Memory Clearing Header
This header uses a jumper cap to clear the CMOS memory.
• Pin 1-2 shorted (default): Normal operation.
• Pin 2-3 shorted: Clear CMOS memory.
WARNING: Turn the power off first (including the +5V standby power) before clearing the CMOS
memory. Failing to do so may cause your system to work abnormally or malfunction.
KV7 Series
Hardware Setup 2-7
S2K Mode Select Header (For KV7 only) (4).
This header uses a jumper to select the S2K mode.
Short pin-2 and pin-3 for “Strapping from Hardware” to allow the CPU hardware controls the timing of
S2K bus for a better system flexibility.
The default setting is pin-1 and pin-2 shorted for “Strapping from boot ROM” to allow the internal boot
ROM controls the timing of S2K bus.
KV7:
User’s Manual
2-8 Chapter 2
(5). Wake-up Header
These headers use a jumper cap to enable/disable the wake-up function.
• PS2-PWR1:
Pin 1-2 shorted (default): Disable wake-up function support at Keyboard/Mouse port.
Pin 2-3 shorted: Enable wake-up function support at Keyboard/Mouse port
• USB-PWR1:
Pin 1-2 shorted (default): Disable wake-up function support at USB1 port.
Pin 2-3 shorted: Enable wake-up function support at USB1 port.
• USB-PWR2:
Pin 1-2 shorted (default): Disable wake-up function support at USB2 port.
Pin 2-3 shorted: Enable wake-up function support at USB2 port
KV7 Series
Hardware Setup 2-9
(6). Front Panel Switches & Indicators Headers
This header is used for connecting switches and LED indicators on the chassis front panel.
Watch the power LED pin position and orientation. The mark “+” align to the pin in the figure below
stands for positive polarity for the LED connection. Please pay attention to connect these headers. A
wrong orientation will only cause the LED not lighting, but a wrong connection of the switches could
cause system malfunction.
• HLED (Pin 1, 3):
Connects to the HDD LED cable of chassis front panel.
• RST (Pin 5, 7):
Connects to the Reset Switch cable of chassis front panel.
• SPK (Pin 15, 17, 19, 21):
Connects to the System Speaker cable of chassis.
• SLED (Pin 2, 4):
Connects to the Suspend LED cable (if there is one) of chassis front panel.
• PWR-ON (Pin 6, 8):
Connects to the Power Switch cable of chassis front panel.
• PLED (Pin 16, 18, 20):
Connects to the Power LED cable of chassis front panel.
User’s Manual
2-10 Chapter 2
(7). Additional USB Port Headers
These headers each provide 2 additional USB 2.0 ports connection through an USB cable designed for
USB 2.0 specifications.
KV7 Series
Pin Pin Assignment Pin Pin Assignment
1 VCC 2 VCC
3 Data0 - 4 Data1 -
5 Data0 + 6 Data1 +
7 Ground 8 Ground
9 NC 10 NC
Hardware Setup 2-11
(8). Front Panel Audio Connection Header
This header provides the connection to audio connector at front panel.
• To use the audio connector at front panel, remove all the jumpers on this header, and then
connect to front panel by the extenson cable provided with the chassis.
• To use the audio connector at rear panel, disconnect the extension cable, attach the jumpers back
at pin 5-6, and pin 9-10 (default setting).
KV7:
Pin Pin Assignment Pin Pin Assignment
1 Audio Mic. 2 Ground
3 Audio Mic. Bias 4 VCC
Speaker Out Right
5
Channel
Speaker Out Right
6
Channel Return
7 X 8 NC
Channel
Speaker Out Left
9
Speaker Out Left
10
Channel Return
11 Ground 12 S/PDIF In
13 VCC 14 S/PDIF Out
User’s Manual
2-12 Chapter 2
KV7-V:
Pin Pin Assignment Pin Pin Assignment
1 Audio Mic. 2 Ground
3 Audio Mic. Bias 4 VCC
Speaker Out Right
5
Channel
7 X 8 NC
Speaker Out Left
9
Channel
Speaker Out Right
6
Channel Return
Speaker Out Left
10
Channel Return
KV7 Series
Hardware Setup 2-13
(9). Internal Audio Connectors
These connectors connect to the audio output of internal CD-ROM drive or add-on card.
(10). Accelerated Graphics Port Slot
This slot supports an optional AGP graphics card up to AGP 8X mode. Please refer to our Web site for
more information on graphics cards.
ATTENTION: This motherboard does not support 3.3V AGP cards. Use only 1.5V or 0.8V AGP cards.
User’s Manual
2-14 Chapter 2
(11). Floppy Disk Drive Connector
This connector supports two standard floppy disk drives via a 34-pin 34-conductor ribbon cable.
Connecting the Floppy Disk Drive Cable:
1. Install one end of the ribbon cable into the FDC1 connector. The colored edge of the ribbon cable
should be aligned with pin-1 of FDC1 connector.
2. Install the other end(s) of ribbon cable into the disk drive connector(s). The colored edge of the
ribbon cable should be also aligned with pin-1 of disk drive connector. The endmost connector
should be attached to the drive designated as Drive A.
KV7 Series
Loading...