3R System HT-4000 User Manual

User Manual

How to connect cables

	POWER LED +	POWER LED : Be sure to match the polarity. Refer to
	POWER LED -	the mainboard manual when connecting
		the cable.
	GND	POWER SW(Switch) : This switch has no polarity.
	M/B PWR	It doesn’t matter which place you
		connect this to the mainboard.

RESET SW

1394
TPA+				1
TPA-				2
TPB+				5
TPB-					6
GND						3 or
VP						7 or
VG						3 or

RESET SW(Switch) : This switch has no polarity.

It doesn’t matter which place you connect this to the mainboard.

IEEE1394 : If the mainboard socket is different from the picture beside, refer to the mainboard user manual and plug the separate pins on your mainboard.

*** Separate cables may be unavailable in some models.

Mainboard Socket

		2	4	6	8 10
	4
	8	1	3	5	7
	4

			VCC1
			USB1+creader
	USB	AUDIO	USB1-
			GND
	USB	AUDIO	CARD READER(USB Power)

:Match them to the pin of mainboard.

* On the LED connector, the pin marked withis positive.

Package Contents and Installation of the parts

PC Speaker

	iMON Remote Controller				ODD Installation
	Driver CD		ODD Cover
					Guide
	Screw 3.5	Screw 3 5mm	Screw 3 10mm	Mainboard	Paper
				Supporter	Washer

1. Mainboard supporter - Use this only where required, and assemble using Paper Washer(Red Washer).

2.Screw 3.5 - Use this to secure HDD, PSU, or Various Slot Cards.

3.Screw 3 - Use this to secure mainboard(5mm), CD-ROM(10mm).

4.Paper Washer – Use this with 3 screws and mainboard supporter for electrical

insulation.

5.PC Speaker – This is installed in mainboard and calls the condition of the system.

6.ODD cover, ODD Installation Guide – Use them when installing CD-ROM.

7.iMon remote controller, Drive CD – The parts for HTPC

Specifications and improvements in the design of our PC case are subject to change without any prior notice.

*Warranty voids when damage is caused by user’s abuse, misuse of the product of a natural disaster.

*Warranty voids when damage is caused by modifying the product of by using the product in improper application.

For the detailed A/S and support, please visit our website(http://www.3rsys.com).

TEL:[phone]

Fax:[phone]

e-mail: [e-mail]

How to connect cables

	4-pin Power Connector:	Fan Power Connector:
	Connect this to PSU.
		Connect this to the 3-pin Fan
	(LCD-equipped model
		provided in the case.
	only)
		(LCD-equipped model only)

Thermal Probe : Place this sensor to the proper place to measure the temperature inside the case.

*Do not place the sensor on CPU core, or Heatsink.

*If there is the gap between cooler base and CPU core because of the wire of the sensor, CPU may be damaged.

*If there is cooler guide, the cable of the sensor should be replaced under the cooler guide to avoid the disconnection.

How to install 5.25” ODD

How to install 3.5” HDD

1. Lay down the body when installing the HDD into 3.5”Bay to do easily.

2. Untie the screws indicated on the left picture and separate the heatsink.

1.Fit ODD installation guide into the hole of ODD.

2.Insert the ODD into 5.25Bay without screws.(Do not separate the front bezel, and put from behind.)

3.Fix ODD with screws(3 10mm).

4.Press the ODD button of the bezel to check the condition of the button.

How to install ODD Cover

1.Pull out the tray of ODD. Press the button after connecting the power or press the hole indicated by the arrow of the picture on the right using clip.

2.Remove the cover by pulling it up using both hands.

3.Peel off the cover film from the supplied tray cover and stick the tray cover on the ODD tray carefully. You can stick the tray cover easily and correctly after putting the tray. Even slight misplacement of the tray cover can handle the smooth movement of he tray. Take good caution.

3.Install the HDD into the hole as shown in the picture. Make sure to remove the thermal pad before installation.

4.Install the separated heatsink again after removing the thermal pad on it.

5. Fix the HDD with 3.5 screws.

LCD Functions

Change of fan control channels <1ch - 2ch - 3ch >

Resets to default settings

1.1-channel Auto Temperature Monitor<The range of temperature Monitor:0~99°C>

2.3-channel Fan Speed Control<low-mid-high>

3.Auto System Running Time Display<0~100%>

4.Auto Audio Frequency Monitor<100R~10K>

5.Auto month, day, hour, minute display<The time which the computer sets up is displayed>

6.Keyboard and Mouse function by remote controller

7.Display of the running program.<Text Slide>

8.Equalizer<It responds to every sound of the computer>

							Fan 1
							Fan 2
					LCD Fan Connection Cable (3pin)
							Fan 3
LCD main power extended cagle
20~24 pin					LCD Thermal Sensor
	LCD 4 pin
	power connector		Case power switch(2pin)		Case
Main power cable	4pin power connector
20~24 pin			M/B PWR GND cable(2pin)
		Power Switch Terminal

Change of fan speed <OFF - Low - Mid -High>

Change of fan speed <High - Mid - Low - OFF>

M-Station is a genuine	Power Supply	Mainboard
HTPC case with style that
perfectly matches other		External USB Terminal
AV components in your
		Inner USB Terminal
living room.

M-StationHT-4000 is equipped with Soundgraph’siMONLCD and comeswithiMONremote controllerand mediacenter application.