3M G5, XT-1 User Manual

3M™ Drive-Thru Systems

Quick Reference Guide

Instructions for G5 Headset Controls and Battery Charging ................2–3

Instructions for XT-1 Headset Controls and Battery Charging .................4

Order Taking Modes .............................................4–5

Enter Configuration Mode (Access Base Station Settings) ...................5

Greeter Setup ...................................................5

Change Basic Volume Settings .......................................6

Change the Monitor Volume .........................................6

Night Volume ....................................................6

Registering Headsets ..............................................7

Change Site Scheduling ............................................7

Store is Now Closed Message .......................................8

Reboot System ..................................................8

Locating Base Station Serial Number ..................................8

Refer to the 3M™ Drive-Thru Systems Model G5
and XT-1 how to videos or operating instructions
for additional information.

1-800-328-0033 • www.3M.com/drivethru

Instructions for G5 Headset Controls and Battery Charging

Headset Controls

Adjustment Slide

Battery Latch

ID Tag

Volume Up

Volume Down

Tap to Release
Headset from
Order Taking

Touch Zone Lane 1

G5 Headset Indicator Light Modes

Touch Zone Lane 2

Indicator LED (see

G5 Headset Indicator
Light Modes below)

Indicator Mode Description

Green (Steady) Light

Red/Green (Steady) Light

Blue (Flashing) Light

Blue (Steady) Light

Lane 1 no car present, stand by

Lane 2 (Dual Lane) no car present, stand by

Vehicle arrived, but not answered

Vehicle present and answered

Red (Steady) Light

2

Talk (either lane or page )

Instructions for G5 Headset Controls and Battery Charging (continued)

Removing Batteries

• Use your finger to gentle press up
on the battery latch. This will release
the battery as shown in Image 1.

• Using your finger nail, gently pull the
discharged battery from the battery
housing as shown in Image 2.

• Insert a fully charged battery in the
housing with the notch on the battery
facing upward. Ensure the battery is
fully inserted.

Image 1

Charging Batteries

To charge a battery, insert the battery in
one of the Charging Stations or place the
G5 headset (with the battery inserted)
into the Headset Charger slot as shown.

• The LED(s) on the battery will now flash
Green indicating the battery is currently
being charged.

• All four LEDS will be lit Green (steady)
to indicate the battery is fully charged.

• Charge batteries after every shift.

Battery Charger

G5 Battery Indicator Light Modes

Indicator (LEDs from Top) Mode Description

Battery is out of G5 battery
charger and the button has
been pressed and held down.

Each LED represents
25% charge.

All 4 LEDs Lit Green (Steady)

3 LEDs Lit Green (Steady)

2 LEDs Lit Green (Steady)

1 LED Lit Green (Steady)

100% charge

75% charge

50% charge

25% charge

Image 2

Headset Charging Station

Top LED

Battery is in charger and
is currently charging.

Each LED represents
25% charge.

Battery end of life.

1st LED Flashing Green

2nd LED Flashing Green

3rd LED Flashing Green

4th LED Flashing Green

Top and Bottom LEDs Lit Green

up to 25% charge

up to 50% charge

up to 75% charge

up to 100% charge

Replace the battery

Headset Cleaning

• For good health and hygiene, every headset should be cleaned on a regular schedule.

• Before cleaning, remove the battery and the soft foam ear pad from the headset.

• Use a damp soft cloth to wipe the surfaces clean. We recommend using a
3M™ 5040 /7065 Cleaning Wipe or a Scotch-Brite® High Performance Cloth.

• DO NOT soak the headset or immerse it in water; you might damage the electronics.

• DO NOT bend the microphone boom.

Bottom LED

3