Page 1
Scotchlok
Instructions
™
Connectors and Tools
July 1994
Issue 2, 80-6107-4684-6
Page 2
Scotchlok
Connector
TM
Connection
Type
Maximum
Insulation
O. D.
in
mm
Butt Splicing
PIC-unfilled
AWG
mm
Cable Type
PIC-filled Pulp or Paper
AWG mm
AWG
Approved Tools
To reduce fatigue, use tool within each splicing
group with highest mechanical advantage
indicated in ( ).
mm
*
UR2
**
UR2-D
*
UY2
**
UY2-D
***
UP2
***
UP3
*
211
*
UB2A
**
UB2A-D
***
UPB
.082 2.08 19-26 .9-.4
.082 2.08
.082 2.08
.082 2.08
.060
.066 1.67 22-26 .7-.4 19-26 .9-.419-26
.082 2.08 19-26 .9-.4 19-26 .9-.4 19-26 .9-.4
19-26 .9-.4 19-26 .9-.4
19-26 .9-.4
19-26 .9-.4
1.52
22-26 .7-.4
19-26 .9-.4 N A
19-26 .9-.4
19-26 .9-.4 19-26 .9-.4
22-26 .7-.4 22-26 .7-.4
.9-.4
19-26 .9-.4
N A
Tap Splicing
.082 2.08
.082 2.08
.050
19-26 .9-.4 19-26 .9-.4 N A
19-26 .9-.4 19-26 .9-.4 19-26 .9-.4
1.27
22-26 .7-.4
24-26 .5-.4
Can be used on 22 (.7)
foam insulated cable
22-26 .7-.4
E-9BM
(10-1)
E-9C/CW (7-1)
E-9E (4-1)
•
E-9Y (3-1)
E-9E (4-1) E-9BM (10-1) E-9Y (3-1)
E-9BM
(10-1)
E-9E (4-1)
E-9Y (3-1)
*
UDW2
*
UCC
***
UPC
Filled
*
Unfilled
**
Unfilled - Flame Retardant
***
NA Not Applicable
In Line Splicing
Self-stripping drop wire connector designed to accommodate
copper or copper clad steel conductors 16-19 AWG (1.3-0.9 mm)
.175 4.4
in strain relief areas. Ideal for use on Alpha Duct GT-7,
Alpha TEL, F-Drop and C-Drop.
Clear / Cap Only
.060 1.52
.060
22-26 .7-.4 22-26 .7-.4 N A
22-26 .7-.4
1.52
E-9BM
(10-1)
ALL TOOLS APPROVED FOR
BUTT SPLICING MAY BE USED
22-26
.7-.422-26
.7-.4
Note: For health and safety information for
sealant in filled Scotchlok Connectors,
see package label or appropriate Material
Safety Data Sheet.
Page 3
UR2 UR2-D UY2 UY2-D UP2 UP3 UCC UPC
Trim, straighten
conductors
211
Connector to be
removed
Place 211
connector
UB2A UB2A-D UPB
Place side slot
on run wire
Pre-crimp
UDW2
Cut and slit
drop wire 1- 1/4''
Separate, fully
insert conductors
Insert fully
matching line or
ribs of drop wire
Pre-crimp
Twist, cut, insert
tap wire
Crimp with cap
side down
Pre-crimp
raised side
Pre-crimp
Crimp with cap
side down
Test port
Crimp with cap
side down
Crimp with cap
side down
REMEMBER
On ratchet tools
(E-9C, E-9CH )
Squeeze handle until
ratchet releases
E9Y tool should not be used when
•
crimping three 19 AWG/ .9 mm conductors
To reduce fatigue,
use tool with highest
mechanical advantage
Periodically gauge
tools and
connectors
•
Page 4
Important Notice
All statements, technical information and recommendations related to the Seller's products are based on information believed to be reliable,
but the accuracy or completeness thereof is not guaranteed. Before utilizing the product, the user should determine the suitability of the
product for its intended use. The user assumes all risks and liability whatsoever in connection with such use.
Any statements or recommendations of the Seller which are not contained in the Seller's current publications shall have no force or effect
unless contained in an agreement signed by an authorized officer of the Seller. The statements contained herein are made in lieu of all
warranties, express or implied, including but not limited to the implied warranties of merchantability and fitness for a particular purpose which
warranties are hereby expressly disclaimed.
SELLER SHALL NOT BE LIABLE TO THE USER OR ANY OTHER PERSON UNDER ANY LEGAL THEORY, INCLUDING BUT NOT
LIMITED TO NEGLIGENCE OR STRICT LIABILITY, FOR ANY INJURY OR FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES
SUSTAINED OR INCURRED BY REASON OF THE USE OF ANY OF THE SELLER'S PRODUCTS THAT WERE DEFECTIVE.
Telecom Systems Division
6801 River Place Blvd.
Austin, TX 78726-9000
800/426-8688
Printed on 50% recycled paper
with 10% post consumer
© 3M 1994 80-6107-4684-6 (835.0)TG1
Printed in USA
Loading...