3M 9200IW, 9200IC Quick Start Guide

Digital Wall Display

Operator’s Guide Guide de l’operateur Benutzerhandbuch Guida dell’operatore Guía del operador

…interactive whiteboard

9200IW

…deluxe interactive whiteboard

9200IC

ENGLISH

(This page intentionally left blank for printed version)

3M™ Digital WallDisplay

Contents

ENGLISH

Introduction ....................................................................................................................................................7

Installation and System Setup .....................................................................................................................17

Operation .....................................................................................................................................................22

Remote Control Unit ...................................................................................................................................24

Digital Markers and Eraser ..........................................................................................................................28

Menu System ...............................................................................................................................................30

Using the 3M WallDisplay as a Copyboard ................................................................................................36

Maintenance .................................................................................................................................................40

Troubleshooting ...........................................................................................................................................49

Service Information .....................................................................................................................................57

Appendix ......................................................................................................................................................58

FRANÇAIS

Introduction ..................................................................................................................................................65

Installation et Configuration du Système ....................................................................................................75

Fonctionnement ...........................................................................................................................................80

Télécommande .............................................................................................................................................82

Marqueurs et effaceur numériques ..............................................................................................................86

Système de menu .........................................................................................................................................88

Utilisation du 3M Digitale WallDisplay comme Tableau copieur .............................................................94

Entretien .......................................................................................................................................................98

Dépannage .................................................................................................................................................107

Service après-vente ....................................................................................................................................115

Annexe .......................................................................................................................................................116

ENGLISH

FRANÇAIS DEUTSCH ITALIANO ESPAÑOL

DEUTSCH

Einleitung ...................................................................................................................................................123

Installation und Einrichtung des Systems .................................................................................................133

Bedienung ..................................................................................................................................................138

Fernbedienung ...........................................................................................................................................140

Digitale Marker und Tafelwischer .............................................................................................................144

Menüsystem ...............................................................................................................................................146

Einsatz des WallDisplay als Copyboard ...................................................................................................152

Wartung ......................................................................................................................................................156

Fehlerbeseitigung .......................................................................................................................................165

Serviceinformationen .................................................................................................................................173

Anhang .......................................................................................................................................................174

ENGLISH

Contents

ITALIANO

Introduzione ...............................................................................................................................................181

Installazione e impostazione del sistema ...................................................................................................191

Funzionamento ...........................................................................................................................................196

Telecomando ..............................................................................................................................................198

Indicatori e cancellino digitali ...................................................................................................................202

Sistema di menu .........................................................................................................................................204

WallDisplay come Copiatrice ...................................................................................................................210

Manutenzione .............................................................................................................................................214

Risoluzioni dei problemi ...........................................................................................................................223

Informazioni per l’assistenza .....................................................................................................................231

Appendice ..................................................................................................................................................232

ESPAÑOL

Introducción ...............................................................................................................................................239

Instalación del sistema ...............................................................................................................................249

Funcionamiento .........................................................................................................................................254

Unidad de control remoto ..........................................................................................................................256

Marcadores y borrador digitales ................................................................................................................260

Sistema de menús ......................................................................................................................................262

Utilizar el Digital WallDisplay como tablero para copias ......................................................................268

Mantenimiento ...........................................................................................................................................272

Resolución de problemas ...........................................................................................................................281

Información sobre reparaciones .................................................................................................................289

Apéndice ....................................................................................................................................................290

3M™ Digital WallDisplay

Contents

Introduction

Thank You for Choosing 3M .........................................................................................................................7

Safety Information .........................................................................................................................................7

Intended Use ..................................................................................................................................................

Product Safety Label ...................................................................................................................................

Save These Instructions ...............................................................................................................................

Trademarks ..................................................................................................................................................

Patents ..........................................................................................................................................................

Software and Copyright License Agreement ...............................................................................................

3M Digital WallDisplay Technical Support .................................................................................................

FCC Statement—Class A ............................................................................................................................

EEC Statement—Class A ............................................................................................................................

Model Identification and Differences ..........................................................................................................

Contents .......................................................................................................................................................14

Optional Accessories ...................................................................................................................................

What’s Next? ...............................................................................................................................................

Part Identification ........................................................................................................................................

3M Digital Wall Display Features ...............................................................................................................

Installation and System Setup

Recommendation and Things to Consider Before Installing ......................................................................17

Installing the Wall Bracket ..........................................................................................................................

Hanging the 3M Digital WallDisplay ..........................................................................................................

System Setup ...............................................................................................................................................

ENGLISH

7 11 11 11 12 12 12 12 12 13

14 14 15 16

18 19 21

Operation

Startup ..........................................................................................................................................................22

Shutdown .....................................................................................................................................................23

Remote Control Unit

Features ........................................................................................................................................................24

Forward Keypad ...........................................................................................................................................25

Rear Keypad ................................................................................................................................................26

Installing or Replacing Batteries .................................................................................................................27

Digital Markers and Eraser

Assembling Digital Markers ........................................................................................................................28

Assembling Digital Eraser ...........................................................................................................................29

Menu System

Menu Navigation .........................................................................................................................................30

Colorful—Bright Slider ...............................................................................................................................

Warm—Cool Slider .....................................................................................................................................

Volume Slider ..............................................................................................................................................

Mute Menu Function ...................................................................................................................................

Input Select Menu ........................................................................................................................................

Reset All Menu ............................................................................................................................................

Image Adj Sub-Menu ...................................................................................................................................

Tools Sub-Menu ...........................................................................................................................................

30 31 31 32 33 33 34 35

Contents

Using the 3M WallDisplay as a Copyboard

Installing eBeam Software on Your Computer ............................................................................................36

Installing the Software .................................................................................................................................36

Copyboard Mode (9200IC) .........................................................................................................................37

Projection Mode ...........................................................................................................................................37

Using Copyboard Mode (9200IC) ...............................................................................................................37

Using Projection Mode ................................................................................................................................38

ENGLISH

The Interactive Stylus ..................................................................................................................................39

Maintenance

General Maintenance ...................................................................................................................................40

Lamp Usage .................................................................................................................................................40

Onscreen Lamp Messages ...........................................................................................................................40

Lamp Replacement ......................................................................................................................................41

Resetting Lamp Hours .................................................................................................................................44

Replacing ProjectionScreen .........................................................................................................................45

Optical Engine Adjustment ..........................................................................................................................46

Troubleshooting

Common Problems and Solutions ...............................................................................................................49

Onscreen Messages ......................................................................................................................................50

eBeam Software ...........................................................................................................................................51

eBeam Hardware Detection/Use .................................................................................................................51

Network Connection/Shared Meetings ........................................................................................................52

Writing Data/Capture ...................................................................................................................................53

EFI Meeting Applet .....................................................................................................................................55

Background Images .....................................................................................................................................56

3M™ Digital WallDisplay

Service Information

Replacement Parts .......................................................................................................................................57

Optional Accessories ...................................................................................................................................57

Ordering Parts or Getting Information ........................................................................................................57

Appendix

3M™ Digital WallDisplay Specifications ...................................................................................................58

Input/Output Signal Specifications ..............................................................................................................59

Computer Compatibility ..............................................................................................................................59

Printer Compatibility ...................................................................................................................................60

3M™ Digital WallDisplay

Introduction

Thank You for Choosing 3M

Thank you for choosing 3M equipment. This product has been produced in accordance with 3M’s highest quality and safety standards to ensure smooth and troublefree use in the years to come.

For optimum performance, please follow the operating instructions carefully. We hope you will enjoy using this high performance product in your meetings, presentations, and training sessions.

Safety Information

Please read, understand, and follow all safety information contained in these instructions prior to the installation and use of the 3M Digital Wall Display. Retain these instructions for future reference.

Intended Use

Before operating this machine, please read the entire manual thoroughly. The 3M Digital WallDisplay Systems are designed, built, and tested for use indoors, using 3M lamps, 3M mount hardware, and nominal local voltages.

The use of other replacement lamps, outdoor operation, or different voltages has not been tested and could damage the projector or peripheral equipment and/or create a potentially unsafe operating condition.

3M Digital WallDisplay Systems are designed to operate in a normal office environment.

• 16° to 29° C (60° to 85° F)

• 10 to 80% RH (without condensation)

• 0 to 1828 m (0 to 6,000 feet) above sea level

ENGLISH

The ambient operating environment should be free of airborne smoke, grease, oil and other contaminants that can affect the operation or performance of the 3M Digital WallDisplay.

Use of this product in adverse conditions will void the product warranty.

Explanation of Signal Words and Symbols in Safety Labels and Instructions

WARNING:

CAUTION:

Indicates a potentially hazardous situation, which if not avoided, could result in death or serious injury and/or property damage.

Indicates a potentially hazardous situation, which if not avoided, may result in minor or moderate injury and/or property damage.

Warning: HIGH VOLTAGE

Caution: HIGH TEMPERATURE

Warning; HIGH PRESSURE

Attention: Refer to Safety Instructions in Guides

Introduction

3M™ Digital WallDisplay

 WARNING

To reduce the risk associated with hazardous voltage:

• Do not attempt to service the Wall Display other than performing routine lamp replacement. Service should only be performed by a 3M authorized service provider. Aside from the projection lamp assembly, there are no serviceable parts inside the unit.

• Switch power “OFF” and disconnect the plug from electrical outlet before replacing the lamp. Grasp plug and

ENGLISH

pull to disconnect.

• Replace the power cord if damaged.

• Always plug this product into a grounded outlet.

• Do not use in a wet environment.

To reduce the risk associated with hazardous voltage and fire:

• Switch power “OFF” and disconnect the plug from electrical outlet whenever the unit is not in use for an extended period of time.

• Use a properly rated extension cord. Consult an electrical professional if you have questions.

To reduce the risk associated with muscle strain and impact:

• Use only the 3M

™

brand wall mounting hardware kit if wall mounting is desired.

• Strictly follow all installation instructions when installing or removing the Wall Display onto the wall or portable cart.

• Always use more than one person when installing or removing the Wall Display.

• Always keep cart and Wall Display stable.

To reduce the risks associated with glass dust falling from the projection arm into the eye:

• Do not look up towards the projection arm in the event of lamp breakage.

To reduce the risk associated with high temperature related to a hot lamp assembly:

• Wait at least 45 minutes for the lamp assembly to cool before replacing.

To reduce the risk associated with the release of high pressure related to a hot lamp:

• Wait at least 45 minutes for the lamp assembly to cool before replacing.

To reduce the risk associated with unexpected lamp rupture related hazards:

• Ventilate the area where the lamp rupture occurred. The lamp operates at high pressure and at high temperature.

• Have a 3M authorized service provider replace a ruptured lamp.

• Always handle the fragile lamp module with care.

• Wash your hands thoroughly if you come in contact with lamp debris.

• Replace the lamp module when the lamp replacement message appears.

• Never replace the lamp module with a previously used lamp module.

To reduce the risk associated with choking:

• Keep batteries away from children and pets.

To reduce the risk of associated with environmental contamination, due to mercury in the projection lamp:

• Don't throw the lamp cartridge in the trash. Dispose of the lamp cartridge in accordance with your respective

governmental agencies for hazardous waste. For disposal information in the U.S., contact the Electronic Industries Alliance at www.lamprecycle.org. In Canada, contact the Electronic Product Stewardship Canada at www.wpsc.ca.

3M™ Digital WallDisplay

 WARNING

To reduce the risk of environmental contamination due to lead based solder:

Introduction

• Don’t throw circuit boards in the trash. Dispose of circuit boards in accordance with your respective governmental agencies for hazardous waste.

To reduce the risk associated with radio interference:

• This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.

To reduce the risks associated with hazards related to the use of alcohol based cleaners;

• Follow all instructions and recommendations in the Sanford Expo Whiteboard Cleaner Material Safety Data Sheet and product label.

 CAUTION

To reduce the risk associated with tripping over cables:

• Position the product’s power cord and data cable so that they will not be tripped over.

To reduce the risk associated with chemical leakage, hot battery surface, and battery rupture:

• Use only same type AAA alkaline batteries in remote control.

• Use only same type AA alkaline batteries in presentation pen.

• Use only same type CR2032 Lithium coin batteries in pens and eraser.

• Avoid fire and heat sources above 100° C.

• Do not short circuit batteries.

ENGLISH

• Do not attempt to recharge batteries.

• Do not break or disassemble batteries.

• Avoid eye and skin contact, ingestion and inhalation of battery chemicals in the event of a ruptured or broken battery.

• Replace all batteries at the same time.

• Properly orient the plus (+) and minus (-) terminals of the batteries.

• Remove batteries when not used for an extended period of time.

To reduce the risks associated with impact from the projection arm and tripping over the legs of the portable cart:

• Do not use this Wall Display around unsupervised children.

• Do not allow children to hang onto the projection arm.

Introduction

3M™ Digital WallDisplay

IMPORTANT NOTES

• In some countries, the voltage is not stable. This appliance is designed to operate within a range of 100~240 Vac. In these countries, it is recommended to install a power stabilizer unit.

• Do not manually open or close the projection arm while the 3M Digital Wall Display is in operation.

• Save the shipping box and packing materials in the event the 3M Digital WallDisplay should ever need to be moved.

ENGLISH

• For other types of wall material (e.g. wood, concrete, concrete block) use mounting hardware that is properly rated for the weight of the unit and is intended for specific wall material.

• Most of the weight is at the projection head/speakers end of the 3M Digital WallDisplay.

• Use the enclosed cables to ensure image and audio quality. Substituting cables of lesser quality may result in poor image quality or audio noise.

• There is a 30-second reset period before the On/Off Button will function again. During this period, the On/Off

Button will flash red.

• If the 3M Digital WallDisplay will not be moved or disconnected, leave the Master Power Switch on for your

convenience.

• Do not turn off the Master Power Switch or unplug the power cord before pressing the On/Off Button.

After the On/Off Button is pressed, the fan continues for approximately five minutes to cool the 3M Digital WallDisplay.

• The USB or serial mouse cable must be connected between the 3M Digital WallDisplay and the computer

when using Mouse mode.

• Avoid excessive heat and humidity. Do not mix old and new batteries or different types of batteries.

• The eBeam Software detects the color of the marker sleeve, not the color of the marker inside it, unless

specifically changed. Normal pressure on the marker as you write on the 3M Digital WallDisplay screen sends a “writing” signal in that sleeve’s designated color.

• The signal transmitter in the digital sleeve is located just behind the tip of the marker. Grasp the sleeve by the

main barrel so your fingers will not block the signal.

• Choose New Page to save your work before you erase the board.

• You must hear or feel a distinctive snap to ensure facade is securely attached.

• Do not reset the lamp hours if the lamp cartridge was not changed. This can damage internal components.

• Before continuing with this adjustment, move the arm assembly up and down to relieve any stress and see if

the arm will realign itself and project an aligned image.

• After making adjustments it may be necessary to perform the side to side adjustment to center the image

properly.

3M™ Digital WallDisplay

Wall Display

from 3M

Introduction

Product Safety Label

The following safety label is used on or within the 3M Digital WallDisplay to alert you to this area requiring your attention.

ENGLISH

Save These Instructions

The information contained in this manual will help you operate and maintain your 3M Digital WallDisplay.

Trademarks

The 3M logo and 3M are registered trademarks of 3M Company. Vikuiti is a trademark of 3M Company. Microsoft, Windows, Windows NT, Word, Excel, PowerPoint, Internet Explorer, and NetMeeting are either

registered trademarks or trademarks of the Microsoft Corporation in the United States and/or other countries. IBM is a registered trademark of International Business Machines Corporation. Apple Macintosh and Apple PowerBook are registered trademarks of Apple Computer, Inc., registered in the U.S.

and other countries. Intel and Pentium are registered trademarks of Intel Corporation or its subsidiaries in the U.S. and other

countries. Digital Light Processing is a trademark or registered trademark of Texas Instruments. eBeam, e-Beam, eBeam Mouse, eBeam Moderator, eBeam Software, ImagePort and eBeam Presenter are

registered trademarks of Luidia, Inc. Sun and Java are trademarks or registered trademarks of Sun Microsystems, Inc. in the United States and other

countries. UNIX is a registered trademark in the United States and other countries, licensed exclusively through X/Open

Company Limited. Palm is a trademark of Palm Computing, Inc. or its subsidiaries.

Introduction

Netscape and the Netscape N and Ship’s Wheel logos are registered trademarks of Netscape Communications Corporation in the U.S. and other countries. Navigator and Communicator are also trademarks of Netscape Communications Corporation and may be registered outside the U.S.

All other products are trademarks or registered trademarks of their respective companies.

3M™ Digital WallDisplay

Patents

3M Digital WallDisplay is protected by Utility Patent 6,179,426 and Design Patent D442,205.

ENGLISH

Other patents pending.

Software and Copyright License Agreement

The software in this distribution is copyrighted and licensed by Luidia, Inc.

3M Digital WallDisplay Technical Support

• In U.S. or Canada: 1-800-328-1371

• Web Site: http://www.3M.com/walldisplay

FCC Statement—Class A

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Instructions to Users This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide a reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Notice

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment

Regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel

brouilleur du Canada.

EEC Statement—Class A

This machine was tested against the 89/336/EEC (European Economic Community) for EMC (Electro Magnetic Compatibility) and fulfills these requirements.

Video Signal Cables

Double shielded coaxial cables (FCC shield cable) must be used, and the outer shield must be connected

to the ground. If normal coaxial cables are used, the cable must be enclosed in metal pipes or in a similar way to reduce the interference noise radiation.

Video Inputs

The input signal amplitude must not exceed the specified level. (See Appendix for these levels.)

3M™ Digital WallDisplay

Model Identification and Differences

Identify Model

Introduction

The nameplate, located behind the storage door, identifies the 3M Digital WallDisplay (DWD). Push the storage door to open it. The figure below shows the nameplate, and the table shows the model numbers and corresponding model names.

Model Number Model Name

9000PD 3M Digital WallDisplay 9000PD for Projection Display 9200IC 3M Digital WallDisplay 9200IC with Interactive Collaboration 9200IW 3M Digital WallDisplay 9200IW with Interactive Whiteboard

ENGLISH

Model Differences

Below is a table that identifies the differences between the 3M Digital WallDisplay models.

Model Number Projection Screen Copyboard* Interactive Whiteboard**

9000PD

9200IW NO YES

9200IC YES YES

Easy Dry-Erase and

Projection

NO NO

* The Copyboard feature allows you to print notes written on the 3M Digital WallDisplay to an attached printer.

(PCL3 compatible printer required. See list in Appendix.)

** The Digital Whiteboard feature allows you to capture notes written on the 3M Digital WallDisplay with an

attached computer or use the 3M Digital WallDisplay as an interactive display for a computer.

Introduction

POWER

R MOUSE

INPUT

BLANK

MUTE

OFF

1 2 3 4 5 6

3M™ Digital WallDisplay

Contents

The 3M Digital WallDisplay (3M DWD) is shipped with the necessary cables required for standard VCR, PC, Macintosh or laptop computer connections. Carefully unpack and verify that you have all of the items shown below. If any are missing, please contact your place of purchase.

ENGLISH

Remote

Control

Mac

adapter

Power Cable

(US, UK, Euro)

Serial Cable

(with

batteries)

PC Audio Cable

Digital Eraser

S-Video Cable

Operator’s

Guide

USB Cable

Product

Registration

Card

Optional Accessories

• Accessory Tray/Laptop Shelf • Easy-Erase Screen

• Replacement Lamp Kit • Extended Warranty

Lithium Ion

Batteries

(10)

DVI-D Cable

4 Pen Sleeves

High-Performance

Cleaning Cloth

3-Conductor

Video/Audio Cable

Dry-Erase Markers

3M DWD for 9200IC Only

Interactive

Stylus

VGA Cable

Software CD-ROM

• Screen

Note: Save the shipping box and packing materials in the event the 3M Digital WallDisplay should ever need

to be moved.

What’s Next?

After the 3M Digital WallDisplay has been installed in your meeting room, you are ready to set it up. Please read this guide thoroughly before operating your new 3M Digital WallDisplay. Be sure to check our web site (www.3M.com/walldisplay) regularly for updates and supplemental information.

3M™ Digital WallDisplay

Wall Display

from 3M

AUDIO

USB

MOUSE

SERIAL MOUSE

RS-232

AUDIO VIDEO COMPUTERROW

1 2 (THIS ROW FOR DIGITAL WHITEBOARD OPTION ONLY) PRINTER COMPUTER

S-VIDEO

RCA VGA DVI-D

OUT

MENU KEYPAD

Part Identification

Introduction

7 8 9

1. Facade

2. Lamp Housing Door (behind facade)

3. Projection Screen

4. Left Bezel

5. Remote Control Unit

6. Storage Door

7. Storage Door Window

8. On/Off Button

9. Infrared Remote Sensor

10. Connection Panel Door

11. Right Bezel

12. Speakers

13. Projection Head

14. Projection Arm

15. Connection Panel

16. Menu Keypad

17. Status LED Indicators

18. Master Power Switch

19. AC Power Cord Socket

ENGLISH

Introduction

3M™ Digital WallDisplay

3M Digital Wall Display Features

The 3M Digital WallDisplay combines the following features into one sleek, sophisticated package.

• Full connectivity for computer or video presentations

• Large 60˝ diagonal screen

• 4:3 screen aspect ratio matches business applications and viewing data

• Flat screen allows extra wide (up to 170°) viewing angles

ENGLISH

• Projection arm position guarantees image is in focus every time

• Allows presenter to move without blocking image

• Built-in, powerful stereo speaker system

• Single button operation

• Hand-held remote control for most functions

• Print your meeting notes directly to a PCL3-compatible printer

• 3M Digital WallDisplay 9200IC and 9200IW unique features:

- Capture notes in color and save them in various file formats instantly (JPEG, GIF, TIFF, HTML, PDF, vector PDF, EPS, BMP, WBD)

- Turn the 3M Digital WallDisplay into an interactive computer screen by using the virtual mouse

- Playback feature allows you to review all drawings on the board, including erased items

- Share meeting notes in real time anywhere in the world via the Internet

3M™ Digital WallDisplay

from 3M

41"

(1.04 m)

48"

(1.2 m)

48"

(1.2 m)

4" (100 mm)

88 1/2"

(2.25 m)

91"

(2.3 m)

Installation and System Setup

Recommendation and Things to Consider Before Installing

Location of Unit

• Place near AC outlet. The AC power connection is located on the lower-left corner of the 3M Digital

WallDisplay (the unit). The AC power cord supplied with the unit is 6 feet (2 m) long.

• Service and screen replacement – The projection screen is removed from the side of the unit during replacement

or service. For ease of replacement and access, position the unit 48 inches from the nearest obstruction or adjacent wall.

• Low-hanging lights – The projection arm extends 3 1/3 feet from the unit while in operation. Ensure that the

projection arm will not come in contact with low-hanging light fixtures.

Air Ventilation

• Minimum clearance around the unit should be 4 inches.

• Air Vents – keep the air vents clear of objects and dust.

ENGLISH

Installation and System Setup

To Floor

Installing the Wall Bracket

Unpacking Wall Bracket and Hardware

1. Place the shipping container face up on the floor.

2. Open the end of the shipping container.

3. Slide the shipping tray partially out the container.

4. Locate and Remove the wall bracket and hardware.

ENGLISH

The hardware is taped to the wall bracket.

Installation for a Hollow Wall-Drywall

1. Determine the desired location of the unit. Locate

all wall studs in area.

2. While holding the bracket in place, use a

carpenter’s level to ensure the proper level and then mark the three hole locations on the wall. Ensure that no studs are behind the hole locations.

3M™ Digital WallDisplay

3. Using a Phillips screw driver, screw the supplied

anchors into the wall until they are flush with the wall surface.

4. Align the wall bracket holes over the wall anchors

and secure with the washer and anchor screws. Confirm that the wall bracket is level before tightening the screws.

Note: For other types of wall material (e.g. wood, concrete, concrete block) use mounting hardware that is properly rated for the weight of the unit and is intended for specific wall material.

3M™ Digital WallDisplay

Hanging the 3M Digital WallDisplay

Unpacking the 3M Digital WallDisplay

Installation and System Setup

1. Place the shipping container face up on the floor

and open the end previous opened.

2. Slide the shipping tray out of the shipping

container.

3. Remove the accessory box(es) from the top

support.

4. Remove the top support.

5. Remove the plastic bag from the 3M Digital

WallDisplay by lifting the top of the unit and pushing the bag towards the bottom of the unit. Then set down the top.

6. Lift up the bottom and remove the bag completely.

7. Remove and set aside the tape holding the

projection arm in place.

ENGLISH

8. Remove the projection arm shipping foam, by

opening the projection arm from the left.

9. Replace the tape to hold the projection arm in place

while hanging on the wall.

+ 43 hidden pages

3M 9200IW, 9200IC Quick Start Guide

Specifications and Main Features

Frequently Asked Questions

User Manual

Introduction

Installation and System Setup