3M 8000VC, 8000PD Operator Guide

Operator ’s Guide Guide de l’operateur Benutzerhandbuch Guida dell’operatore Guía del operador
…for video teleconferencing
…for projection
8000PD
January 2005 78-6970-9184-7 Rev. C
Copyright © 2005, 3M. All Rights Reserved.
8000VC
3M™ Digital WallDisplay
Contents
English
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
System Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Remote Control Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Menu System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Français
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Installation du système . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Fonctionnement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Télécommande . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Système de menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Entrieten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Dépannage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Service après-vente . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Annexe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Deutsch
Einleitung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Enrichten des Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Bedienung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Fernbedienung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Menüsystem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Wartung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Fehlerbeseitigung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Serviceinformationen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Anhang . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Italiano
Introduzione . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Impostazione del sistema . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Funzionamento . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Telecomando . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Sistema di menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Manutenzione . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Risoluzioni dei problemi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Informazioni per l’assistenza . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Appendice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Español
Introducción . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Configuración del sistema . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Funcionamiento . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Unidad de control remoto . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Sistema de menús . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Mantenimiento . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Resolución de problemas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Información sobre servicio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Apéndice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
ENGLISH
FRANÇAIS
DEUTSCH
ITALIANO
ESPAÑOL
©3M 2003. All Rights Reserved.
2
Operator ’s Guide
…for projection
8000PD
…for video teleconferencing
8000VC
October 2003 78-6970-9184-7 Rev. B
Copyright © 2003, 3M. All Rights Reserved.
©3M 2003. All Rights Reserved. 3
ENGLISH
(This page intentionally left blank for printed version)
©3M 2003. All Rights Reserved. 4
5
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
Contents
Introduction
Thank You for Choosing 3M . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Intended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Product Safety Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Save These Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Patents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
3M Digital WallDisplay Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
FCC Statement—Class A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
EEC Statement—Class A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Model Identification and Differences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
What’s Next? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Part Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
3M Digital WallDisplay Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
System Setup
Connecting to Various Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Operation
Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Remote Control Unit
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Forward Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Rear Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Installing or Replacing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Menu System
Menu Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Colorful—Bright Slider . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Warm—Cool Slider . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Volume Slider . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Mute Menu Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Input Select Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Reset All Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Image Adj Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Tools Sub-Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Maintenance
General Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
6
Contents
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
Lamp Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Onscreen Lamp Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Lamp Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Resetting Lamp Hours . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Replacing Projection Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Troubleshooting
Common Problems and Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Onscreen Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Service Information
Parts and Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Ordering Parts or Getting Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Appendix
3M Digital WallDisplay Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Input/Output Signal Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Computer Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
7
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH

Introduction

Thank You for Choosing 3M
Thank you for choosing 3M equipment. This product has been produced in accordance with 3M’s highest quality and safety standards to ensure smooth and troublefree use in the years to come.
For optimum performance, please follow the operating instructions carefully. We hope you will enjoy using this high performance product in your meetings, presentations, and training sessions.
Intended Use
Before operating this machine, please read the entire manual thoroughly. The 3M Digital WallDisplay Systems are designed, built, and tested for use indoors, using 3M lamps, 3M mount hardware, and nominal local voltages.
The use of other replacement lamps, outdoor operation, or different voltages has not been tested and could dam­age the projector or peripheral equipment and/or create a potentially unsafe operating condition.
3M Digital WallDisplay Systems are designed to operate in a normal office environment.
• 16° to 29° C (60° to 85° F)
• 10 to 80% RH (without condensation)
• 0 to 1828 m (0 to 6,000 feet) above sea level
The ambient operating environment should be free of airborne smoke, grease, oil and other contaminants that can affect the operation or performance of the 3M Digital WallDisplay.
Use of this product in adverse conditions will void the product warranty.
Safety Precautions
Read and understand all instructions before using. Pay particular attention to areas where this symbol is shown:
Note: Emphasizes important conditions or details.
•Close supervision is necessary when any appliance is used by or near children. Do not leave appliance unattended while in use.
•Never look directly into the projector lens when the lamp is on. The short-arc mercury lamp produces a strong light that could damage your eyesight.
•Care must be taken, as burns can occur from touching hot parts when replacing the lamp.
•Do not operate appliance with a damaged cord or if the appliance has been dropped or damaged, until it has been examined by a qualified service technician.
•Position the cord so that it will not be tripped over, pulled or placed in contact with hot surfaces.
• If an extension cord is necessary, a cord with a current rating at least equal to that of the appliance should be used. Cords rated for less amperage than the appliance may overheat.
WARNING
Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation which, if not avoided, could result in minor or moderate injury. It may also be used to alert against unsafe practices.
8
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
Introduction
Safety Precautions
•Always unplug appliance from electrical outlet before cleaning and servicing and when not in use. Grasp plug and pull to disconnect.
•To reduce the risk of electric shock, do not immerse this appliance in water or other liquids.
•To reduce the risk of electric shock, do not disassemble this appliance. Request a qualified technician when service or repair work is required. Incorrect reassembly can cause electric shock when the appli­ance is subsequently used.
• Connect this appliance to a grounded outlet.
•Keep all ventilation openings free of any obstructions.
• The projection lamp contains mercury. Always dispose of this lamp in a proper manner according to local regulations.
•Do not apply force to the projection arm. This may cause permanent damage to the unit or may cause personal injury.
•Do not manually open or close the projection arm while the 3M Digital WallDisplay is in operation.
• The 3M Digital WallDisplay’s projection arm is motorized, and extends 42˝ (106 cm) from the installation while in use. Caution should be taken when operating or walking near the 3M Digital WallDisplay. It is possible a tall person’s head or an upraised hand could come in contact with the pro­jection arm.
•Do not place the product in direct sunlight, near heaters or heat radiating appliances.
9
Introduction
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
Product Safety Label
The following safety label is used on or within the 3M Digital WallDisplay to alert you to this area requiring your attention.
Save These Instructions
The information contained in this manual will help you operate and maintain your 3M Digital WallDisplay.
CAUTION
In some countries, the voltage is NOT stable. This appliance is designed to operate within a range of 100~240 volts, ±10 volts, but it could fail if power drops or surges of ±10 volts occur. In these high-risk areas, it is recommended to install a power stabilizer unit.
Wall Display
from 3M
Introduction
10
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
Trademarks
The 3M logo and 3M are registered trademarks of 3M Company. Vikuiti is a trademark of 3M Company. Microsoft, Windows, Windows NT, Word, Excel, PowerPoint, Internet Explorer, and NetMeeting are either reg-
istered trademarks or trademarks of the Microsoft Corporation in the United States and/or other countries. IBM is a registered trademark of International Business Machines Corporation. Apple Macintosh and Apple PowerBook are registered trademarks of Apple Computer, Inc., registered in the
U.S. and other countries. Intel and Pentium are registered trademarks of Intel Corporation or its subsidiaries in the U.S. and other coun-
tries. Digital Light Processing is a trademark or registered trademark of Texas Instruments. eBeam, e-Beam, eBeam Mouse, eBeam Moderator, eBeam Software, ImagePort and eBeam Presenter are regis-
tered trademarks of Electronics for Imaging, Inc. Sun and Java are trademarks or registered trademarks of Sun Microsystems, Inc. in the United States and other
countries. UNIX is a registered trademark in the United States and other countries, licensed exclusively through X/Open
Company Limited. Palm is a trademark of Palm Computing, Inc. or its subsidiaries. Netscape and the Netscape N and Ship’s Wheel logos are registered trademarks of Netscape Communications
Corporation in the U.S. and other countries. Navigator and Communicator are also trademarks of Netscape Communications Corporation and may be registered outside the U.S.
All other products are trademarks or registered trademarks of their respective companies.
Patents
3M Digital WallDisplay is protected by Utility Patent 6,179,426 and Design Patent D442,205. Other patents pending.
3M Digital WallDisplay Technical Support
• In U.S. or Canada: 1-800-328-1371
• Web Site: http://www.3M.com/walldisplay
Introduction
11
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
FCC Statement—Class A
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, includ­ing interference that may cause undesired operation.
Instructions to Users
This equipment has been tested and found to comply with the limits for a Class Adigital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide a reasonable protection against harmful interference when the equipment is operated in a commercial environment. Thisequipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruc tion manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Notice
This Class Adigital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe Arespecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
EEC Statement—Class A
This machine was tested against the 89/336/EEC (European Economic Community) for EMC (Electro Magnetic Compatibility) and fulfills these requirements.
Video Signal Cables
Double shielded coaxial cables (FCC shield cable) must be used, and the outer shield must be connected to the ground. If normal coaxial cables are used, the cable must be enclosed in metal pipes or in a simi­lar way to reduce the interference noise radiation.
Video Inputs
The input signal amplitude must not exceed the specified level. (See Appendix for these levels.)
WARNING
This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.
Introduction
12
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
Model Identification and Differences
Identify Model
The nameplate, located behind the storage door, identifies the 3M Digital WallDisplay (DWD). Push the storage door to open it. The figure below shows the nameplate, and the table shows the model numbers and correspon­ding model names.
Model Number Model Name
8000DP 3M Digital WallDisplay 8000DP for Projection Display 8000VC 3M Digital WallDisplay 8000VC for Video Teleconferencing 8100CB 3M Digital WallDisplay 8100CB with Copyboard Display 8200IC 3M Digital WallDisplay 8200IC with Interactive Collaboration
8200IW 3M Digital WallDisplay 8200IW with Interactive Whiteboard
Model Differences
Below is a table that identifies the differences between the 3M Digital WallDisplay models.
Model Number Projection Screen Copyboard* Interactive Whiteboard**
8000DP Easy Dry-Erase and NO NO
Projection
8000VC 3M Vikuiti High Brightness NO NO
for projection only
8100CB Easy Dry-Erase and YES NO
Projection
8200IW Easy Dry-Erase and YES NO
Projection
8200IC Standard Projection YES YES
and Dry-Erase
*The Copyboard feature allows you to print notes written on the 3M Digital WallDisplay to an attached printer. (PCL3 compatible printer required. See list in Appendix.)
** The Digital Whiteboard feature allows you to capture notes written on the 3M Digital WallDisplay with an attached computer or use the 3M Digital WallDisplay as an interactive display for a computer.
CAUTION
Do not use markers, dry-erase or otherwise, on the 3M Digital WallDisplay for Video Teleconferencing screen. Marks cannot be removed from the 3M Vikuiti High Brightness projection screen.
Model Number
Introduction
13
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
Contents
The 3M Digital WallDisplay is shipped with the necessary cables required for standard VCR, PC, Macintosh or laptop computer connections. Carefully unpack and verify that you have all of the items shown below. If any are missing, please contact your place of purchase.
Optional Accessories
• Accessory Tray/Laptop Shelf • Easy-Erase Screen
• Replacement Lamp Kit • Extended Warranty
Note: Save the shipping box and packing materials in the event the 3M Digital WallDisplay should ever
need to be moved.
What’s Next?
After the 3M Digital WallDisplay has been installed in your meeting room, you are ready to set it up. Please read this guide thoroughly before operating your new 3M Digital WallDisplay. Be sure to check our web site
(www.3M.com/walldisplay) regularly for updates and supplemental information.
POWER
R MOUSE
MENU
INPUT
BLANK
MUTE
ON
OFF
1 2 3 4 5 6
3
M™
D
ig
ita
l W
a
llD
is
p
la
y
80
0
0
D
P
...fo
r P
ro
je
ctio
n
D
i
sp
la
y
3
M™
D
ig
ita
l W
a
llD
isp
la
y
8
0
0
0
V
C
...fo
r V
id
eo
T
e
le
co
n
feren
cin
g
Remote Control
(with batteries)
Mac
adapter
Power Cable
(US, UK, Euro)
Serial
Mouse Cable
DVI-D Cable
3-Conductor
Video/Audio Cable
VGA Cable
PC Audio
Cable
S-Video
Cable
USB
Cable
Operator’s Guide
(CD-ROM)
Product Registration
Card
Introduction
14
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
Part Identification
1
3
5
11
2
4
12
6
7 8 9
10
13
14
15
16
17
18
19
1. Facade
2. Lamp Housing Door (behind facade)
3. Projection Screen
4. Left Bezel
5. Remote Control Unit
6. Storage Door
7. Storage Door Window
8. On/Off Button
9. Infrared Remote Sensor
10. Connection Panel Door
11. Right Bezel
12. Speakers
13. Projection Head
14. Projection Arm
15. Connection Panel
16. Menu Keypad
17. Status LED Indicators
18. Master Power Switch
19. AC Power Cord Socket
R
POWER
MOUSE
MENU
MUTE
BLANK
INPUT
Wall Display
from 3M
PC
USB
AUDIO
MOUSE
1
2 (THIS ROW FOR DIGITAL WHITEBOARD OPTION ONLY) PRINTER COMPUTER
OUT
S-VIDEO RCA VGA DVI-D
IN
SERIAL MOUSE
RS-232AUDIO VIDEO COMPUTERROW
1
2
3
MENU KEYPAD
4
Introduction
15
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
3M Digital WallDisplay Features
The 3M Digital WallDisplay combines the following features into one sleek, sophisticated package.
• Full connectivity for computer or video presentations
• Large 60˝ diagonal screen
• 4:3 screen aspect ratio matches business applications and viewing data
•Flat screen allows extra wide (up to 170°) viewing angles
•Projection arm position guarantees image is in focus every time
•Allows presenter to move without blocking image
• Built-in, powerful stereo speaker system
• Single button operation
• Hand-held remote control for most functions
• 3M Vikuiti High Brightness screen for improved image quality (3M Digital WallDisplay 8000VC only)
16
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH

System Setup

Connecting to Various Equipment
It only takes a few minutes to connect the 3M Digital WallDisplay to your computer, VCR, DVD player, video conference unit, or other devices.
The connection panel is located underneath the bottom right corner of the 3M Digital WallDisplay, under the Connection Panel Door. Press and release door to access connection panel.
Note: Use the enclosed cables to ensure image and audio quality. Substituting cables of lesser quality may
result in poor image quality or audio noise.
PC Audio Connects to the computer’s audio output and provides audio for VGA and DVI-D
(Digital Visual Interface - Digital only) inputs.
USB Mouse Connects to the computer’s USB port and provides wireless mouse control using the 3M
Digital WallDisplay remote control
Disk Pad button.
Audio Out Connects to an external audio amplifier and provides audio from the active audio
source.
Audio In Connects to the audio output of a video device (e.g. VCR or DVD), and provides audio
for both S-Video and RCA video inputs.
S-Video Connects to an S-Video output signal. RCA Video Connects to a composite video device. DVI-D Connects to a computer that supports the DVI-D interface. VGA Connects to the VGA or monitor Out port of a computer. Serial Mouse Connects to a computer’s 9-pin serial port and provides wireless mouse control using
the 3M Digital WallDisplay remote control Disk Pad button.
RS-232 Connects to a control device’s serial port and provides control of the 3M Digital
WallDisplay using RS-232C protocol and the specified serial commands.
PC
AUDIO
MOU
(THIS ROW FOR DIGITAL WHITEBOARD OPTION ONLY
USB
PC
Mouse
Audio
FRONT OF PANEL
BOTTOM OF PANEL
1
2
USB
SE
AUDIO
OUT
)
Out S-Video RCA
Audio
I
N
In
VIDEO
S-VIDEO
RCA
PRINTERC
Video
OMPUTER
COMPUTE
Computer
RROW
VGADVI-D
VGADVI-D
SE
RIA
MOU
Serial
Mouse
L
SE
RS-
RS-232
232
17
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH

Operation

Startup
1. Plug power cord into wall socket.
2. Flip on the
Master Power Switch beneath the lower left corner of the 3M Digital WallDisplay, near the
3M label. This should stay on at all times. Now the 3M Digital WallDisplay is in standby mode. The large oval
On/Off Button will be backlit amber after several seconds.
3. Press the
On/Off Button in the center of the lower front panel. The projection arm will extend outward
from its housing at the top of the 3M Digital WallDisplay unit. Do not block its movement.
4. When the projection arm is fully extended, the lamp will turn on automatically. It will reach full illumina­tion in approximately 60 seconds. The
On/Off Button should then be backlit green.
CAUTION
The 3M Digital WallDisplay’s projection arm is motorized. Do not block its movement or force it to move while the 3M Digital WallDisplay is in operation.
Do not look directly into the 3M Digital WallDisplay projection lens. The light from the lens may cause damage to eyes.
Operation
18
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
Shutdown
1. Press the On/Off Button on the bottom center panel of the 3M Digital WallDisplay unit.
2. The lamp will turn off and the projector arm will return to its housing. The
On/Off Button will flash
red as the arm closes.
Note: There is a 30-second reset period before the On/Off Button will function again. During this
period, the
On/Off Button will flash red.
The fan will continue to run for approximately five minutes to cool the unit.
Note: If the 3M Digital WallDisplay will not be moved or disconnected, leave the Master Power Switch on
for your convenience. Do not turn off the
Master Power Switch or unplug the power cord before pressing the On/Off
Button.
After the On/Off Button is pressed, the fan continues for approximately five minutes to cool
the 3M Digital WallDisplay.
19
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH

Remote Control Unit

Features
The remote control sensor is on the front lower panel of the 3M Digital WallDisplay unit. The distance between the sensor and remote control must be shorter than 4 meters (13 feet).
The remote control unit has two keypads. The Forward keypad is above the flip-top cover. The Rear keypad is beneath the cover. The
Trigger Button is underneath the front IR Sensor of the remote control unit and can be
pressed easily with the index finger.
IR SENSOR
Transmits infrared signals to 3M Digital WallDisplay unit.
DISK PAD
Press to control the computer’s mouse, navigate the menu system, or control the Pointer or Reveal functions.
R MOUSE
Press for right-mouse-button function in mouse mode.
MENU
Press to display onscreen menu system.
BLANK
Press to turn the screen­blanking function on/off.
INPUT
Press to change source of input.
VOLUME
Press to adjust the speaker and Audio Out sound level.
TIMER
Press to turn on/off display of countdown timer.
FREEZE
Press to turn the still-mode function on/off.
REVEAL
Press to uncover part of the screen from top to bottom or from left to right.
LED
Indicates that remote control unit is transmitting signal.
POWER
Press to turn 3M Digital WallDisplay on/off.
MUTE
Press to turn the audio (speaker) function on/off.
POINTER
Press to turn the pointing function on/off.
FORWARD KEYPAD
REAR KEYPAD
TRIGGER BUTTON
Press for left-mouse button functions.
POWER
MUTE
MENU
INPUT
POINTER
FREEZE
REVEAL TIMER
BLANK
VOLUME
R MOUSE
+
Remote Control Unit
20
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
Forward Keypad
Power
Press to turn the 3M Digital WallDisplay on/off. When power is turned on, the 3M Digital WallDisplay will automatically extend the projection arm and ignite the lamp.
Mute Press to temporarily turn off the sound. Press again or press the Volume + or - buttons to restore sound.
Disk Pad
Press to:
• control the computer’s mouse when using the Mouse function.
• select menu items and adjust values in the onscreen menu system.
• control the Pointer position while using the Pointer function.
• control the path of the Reveal function.
While using the onscreen menu system or Pointer function, the computer Mouse function is temporarily dis­abled. To regain computer mouse control, turn off the current function or the onscreen menu system.
Note: The USB or serial mouse cable must be connected between the 3M Digital WallDisplay and the
computer when using Mouse mode.
R Mouse
Acts as the right-mouse button when the mouse function is active.
Menu
Press to display the onscreen menu system. Press again to conceal the onscreen menu system.
Blank
Press to make the screen go blank. Press again to return to normal display function.
Input
Press to change the source of input for 3M Digital WallDisplay. The Input button cycles between Computer, DVI, Composite Video (RCA jacks), and S-Video.
POWER
MUTE
MENU
INPUT
R MOUSE
BLANK
Remote Control Unit
21
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
Rear Keypad
Pointer
Press to turn the pointing function on/off. A green dot will appear on the screen. The dot can be controlled by pressing the arrows on the
Disk Pad.
Volume
Press the + button to increase or the - button to decrease the speaker loudness level. When the audio is muted, the
Volume + or - buttons will also cancel the Mute function.
Timer
Press to turn the timing function on/off. The timer will display on the screen and begin to count down. To change the Timer value, refer to the
On Scrn Timer sub-menu in the Tools menu.
Freeze
Amoving image can be stilled or ‘frozen’ when the Freeze button is pressed. To release the Freeze function, press the
Freeze button again.
Reveal
Press to turn the screen-reveal function on/off. Press the Disk Pad in the desired reveal direction (e.g. press down to reveal from the top down, etc.).
Trigger Button
On the underside of the remote control unit, beneath the IR sensor, press button for left-mouse-button functions.
POWER
MUTE
MENU
BLANK
INPUT
POINTER
VOLUME
FREEZE
REVEAL TIMER
R MOUSE
+
Remote Control Unit
22
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
Installing or Replacing Batteries
1. Push and slide the battery compartment tab in the direction shown, then lift it off.
2. Install two AAAbatteries as indicated by the diagram inside the compartment.
3. Snap the battery compartment cover back on.
Note: Avoid excessive heat and humidity.
Do not mix old and new batteries or different types of batteries.
23
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH

Menu System

Menu Navigation
Most adjustments and settings are available in the main menu and sub-menus. To navigate and make adjustments, use the 3M Digital WallDisplay’s Menu Keypad button or the remote control’s Menu and Disk Pad buttons.
Colorful—Bright Slider
The Colorful—Bright slider adjusts the brightness, contrast, and color saturation levels simultaneously. Move the slider toward Colorful to achieve maximum color saturation and contrast. Move the slider toward Bright to achieve maximum brightness.
To adjust the
Colorful—Bright slider:
1. Open the menu system by pressing the remote control
Menu button or any arrow on the Menu Keypad.
2. Select the
Colorful—Bright slider by pressing the up or down arrows on the remote control Disk Pad or
Menu Keypad.
3. Move the slider by pressing the left or right arrow of the
Disk Pad or Menu Keypad.
4. Close the menu system by pressing the
Menu button or scrolling to Exit and selecting it with the right
arrow of the
Menu Keypad.
1
2
3
MENU KEYPAD
4
Menu System
24
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
Warm—Cool Slider
The Warm—Cool slider adjusts the color temperature. Move the slider toward Warm to achieve warmer, more reddish images. Move the slider toward
Cool to achieve cooler, more bluish images.
To adjust the
Warm—Cool slider:
1. Open the menu system by pressing the remote control
Menu button or any arrow on the Menu Keypad.
2. Select the
Warm—Cool slider by pressing the up or down arrows on the remote control Disk Pad or
Menu Keypad.
3. Move the slider by pressing the left or right arrow of the
Disk Pad or Menu Keypad.
4. Close the menu system by pressing the
Menu button or scrolling to Exit and selecting it with the right
arrow of the
Menu Keypad.
Volume Slider
The Volume slider adjusts the speaker and audio output sound level. Move the slider toward the right to increase the sound. Move the slider toward the left to decrease the sound.
To adjust the
Volume slider:
1. Open the menu system by pressing the remote control
Menu button or any arrow on the Menu Keypad.
2. Select the
Volume slider by pressing the up or down arrows on the remote control Disk Pad or Menu
Keypad
.
3. Move the slider by pressing the left or right arrow of the
Disk Pad or Menu Keypad.
4. Close the menu system by pressing the
Menu button or scrolling to Exit and selecting it with the right
arrow of the
Menu Keypad.
Menu System
25
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
Mute Menu Function
The Mute menu function turns the sound on and off. To turn the
Mute menu function on:
1. Open the menu system by pressing the remote control
Menu button or any arrow on the Menu Keypad.
2. Select the
Mute menu function by pressing the up or down arrows on the remote control Disk Pad or
Menu Keypad.
3. Turn the
Mute function on by pressing the left or right arrow of the Disk Pad or Menu Keypad. The
sound will turn off.
4. Close the menu system by pressing the
Menu button or scrolling to Exit and selecting it with the right
arrow of the
Menu Keypad.
To turn the Mute menu function off:
1. Open the menu system by pressing the remote control
Menu button or any arrow on the Menu Keypad.
2. Select the
Mute menu function by pressing the up or down arrows on the remote control Disk Pad or
Menu Keypad.
3. Turn the
Mute function off by pressing the left or right arrow of the Disk Pad or Menu Keypad. The
sound will turn on.
4. Close the menu system by pressing the
Menu button or scrolling to Exit and selecting it with the right
arrow of the Menu Keypad.
Mute function ON
Mute function OFF
Menu System
26
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
Input Select Menu
The Input Select menu defines the displayed video source. When Input Select menu is selected, the current video source is shown. The
Input options are: Computer (VGA Input), DVI-D, S-Video, Comp. Video (RCA
Video Input), and No Signal. An Input option is available to select when an active video source is connected to the 3M Digital WallDisplay input connection.
To set the
Input Select menu:
1. Open the menu system by pressing the remote control
Menu button or any arrow on the Menu Keypad.
2. Select the
Input Select menu function by pressing the up or down arrows on the remote control Disk Pad
or Menu Keypad.
3. Press the right arrow of the
Disk Pad or Menu Keypad repeatedly until the desired input option is shown.
4. Activate the input option by pressing the left arrow of the
Disk Pad or Menu Keypad.
5. Close the menu system by pressing the Menu button or scrolling to Exit and selecting it with the right
arrow of the
Menu Keypad.
Reset All Menu
The Reset All menu function sets all menu settings to their default settings. To turn the
Reset All menu function on:
1. Open the menu system by pressing the remote control
Menu button or any arrow on the Menu Keypad.
2. Select the
Reset All menu function by pressing the up or down arrows on the remote control Disk Pad or
Menu Keypad.
3. To activate the
Reset All function, press the right arrow of the Disk Pad or Menu Keypad.
4. Close the menu system by pressing the
Menu button or scrolling to Exit and selecting it with the right
arrow of the Menu Keypad.
Menu System
27
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
Image Adj Sub-Menu
The Image Adjustment sub-menu adjusts the projected image settings for the VGA and DVI-D inputs. Use the Vertical Position and Horizontal Position sliders to reposition an image if portions are not visible. Use the Phase and Sync sliders to eliminate vertical banding and noise.
Vertical Position Adjusts the vertical position of the projected image. Horizontal Position Adjusts the horizontal position of the projected image. Phase Adjusts the pixel sampling. Use this to reduce image noise and flicker. Sync Adjusts the expected pixel number in a single video line. Use this to eliminate
banding.
Main Returns to main menu. Exit Leaves the menu system.
To open the
Image Adj submenu:
1. Open the menu system by pressing the remote control
Menu button or any arrow on the Menu Keypad.
2. Select the
Image Adj sub-menu by pressing the up or down arrows on the remote control Disk Pad or
Menu Keypad.
3. To open the
Image Adj sub-menu, press the right arrow of the Disk Pad or Menu Keypad.
4. Scroll to the desired slider and move it to the right or left as needed.
5. Close the menu system by pressing the
Menu button or scrolling to Exit and selecting it with the left or
right arrow of the
Menu Keypad.
To return to the main menu, select
Main and press the left or right arrow of the Disk Pad or Menu Keypad.
Menu System
28
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
Tools Sub-Menu
The Tools sub-menu provides access to the following settings and tools:
Onscreen Timer Allows you to set a timer and display it onscreen. Language Selects which language to use for onscreen commands. (Default language is
English.) It cycles between English, German, Spanish, Italian, and French.
Auto Shutoff Will automatically turn off the 3M Digital WallDisplay within the time desired.
(Default time is 0 minutes.)
Auto Switch When an input source is lost or disconnected, Auto Switch automatically detects
and switches to the next available input source. When Auto Switch is disabled, press the
Input button on the remote control to select the next available input
source.
Usage/Hrs Displays and/or resets 3M Digital WallDisplay’s and lamp’s operating time, in
number of hours.
Audio Adjust Allows you to adjust the bass and treble.
To open the
Tools sub-menu:
1. Open the menu system by pressing the remote control
Menu button or any arrow on the Menu Keypad.
2. Select the
Tools sub-menu by pressing the up or down arrows on the remote control Disk Pad or Menu
Keypad.
3. To open the
Tools sub-menu, press the right arrow of the Disk Pad or Menu Keypad.
4. Scroll to the desired item and adjust as needed.
5. Close the menu system by pressing the
Menu button or scrolling to Exit and selecting it with the right
arrow of the
Menu Keypad.
To return to the main menu, select
Main and press the left or right arrow of the Disk Pad or Menu Keypad.
3M™ Digital WallDisplay

Maintenance

General Maintenance
For general cleaning of the screen and exterior of the 3M Digital WallDisplay, use a damp cloth or dry cleaning cloth such as the 3M High Performance Cleaning Cloth.
Standard dry-erase cleaners may be used on the dry-eraseable screens, such as Sanford Cleaner. Do not use other spray cleaners or solvents on any part of the 3M Digital WallDisplay.
®
Expo®Whiteboard
Lamp Usage
Use and Replacement of Lamp
The 3M Digital WallDisplay lamp has a normal operating time of approximately 1000 hours, called the lamp life. After the lamp has been operating for 900 the first three minutes of operation. When this happens, turn off the 3M Digital WallDisplay and replace the lamp with a new one. Using an old lamp in the 3M Digital WallDisplay could cause a malfunction.
hours or longer, the following messages will appear on the screen for
ENGLISH
Onscreen Lamp Messages
PLEASE CHANGE THE LAMP
The lamp has been in use for 800-900 hours and needs to be changed. After replacing the lamp, reset the lamp timer.
THERE ARE (x) HOURS OF LAMP LIFE REMAINING THE WALLDISPLAY WILL SHUT OFF IN 40 MINUTES
The lamp has been in use for 900-980 hours, and the power will turn off after 40 more minutes. After replacing the lamp, reset the lamp timer.
THERE ARE (x) HOURS OF LAMP LIFE REMAINING THE WALLDISPLAY WILL SHUT OFF IN 5 MINUTES
The lamp has been in use for more than 980-1000 hours, and the power will automatically turn off after 5 minutes. After replacing the lamp, reset the lamp timer.
At 1000 hours the WallDisplay will not turn on. Replace the lamp and reset the lamp timer.
All of these messages will display for no longer than three minutes, but each will display whenever you turn the lamp on again, until the lamp is replaced.
For lamp-changing instructions, please refer to the next page.
©3M 2005. All Rights Reserved.
29
Maintenance
30
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
Lamp Replacement
1. Turn the power off and disconnect the power cord from the outlet.
2. Allow approximately 45 minutes for the lamp to cool, if necessary.
3. There are two indentations behind the top of the facade, near each end. Grasp facade plate at each indentation and pull out and down to remove plate.
4. Loosen the self-contained screw at the upper righthand corner of the lamp housing door with a standard screwdriver.
5. Two black wires connect to the lamp cartridge by a black plastic receptacle on the right side of the lamp cartridge.
WARNING
To reduce the risk of electrical shock, always turn off the 3M Digital WallDisplay unit and disconnect power cord before changing lamp.
Facade
Lamp
Receptacle
Black wires
Maintenance
31
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
5a. Hold down this receptacle with your left thumb and (5b) pull
connectors out of the receptacle with other hand.
6. Push up the metal lever on the lower left side of the lamp cartridge.
7. Grasp the lamp cartridge and pull it straight back out of the lamp compartment.
8. Keep the left edges of the new lamp cartridge aligned with the lamp compartment’s grooves and slide the cartridge smoothly into place.
Lever
5a
5b
Maintenance
32
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
9. Push down the metal lever on the left side of the lamp cartridge.
10. Reconnect black wires to the receptacle.
11.Close the lamp housing door and tighten the screw.
12. Align the slots and tabs of the right side of the facade and projection arm as shown, then snap firmly into place.
13. Align the slots and tabs of the left side of the facade and projection head as shown, then snap firmly into place.
Note: You must hear or feel a distinctive snap to ensure
facade is securely attached.
Whenever the lamp is replaced, please reset the total lamp operating time. (Refer to next page.)
CAUTION
•To reduce the risk of cuts to fingers and/or decreased image quality by touching the lens, do not insert hand into the empty lamp compartment.
This lamp contains mercury. Consult your local hazardous waste regula­tions and dispose of this lamp properly.
•Apotential hazard may exist in the rare case of lamp rupture. Please have a 3M Digital WallDisplay dealer replace a ruptured lamp.
The lamp is extremely hot during normal operation. Before replacing the lamp, wait at least 45 minutes after last operation.
Do not loosen any screws except those mentioned in the lamp replace­ment instructions.
Maintenance
33
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
Resetting Lamp Hours
Please do the following within 10 minutes of turning power on after you replace the lamp.
1. Press the
Menu Keypad or the Menu button on the remote control and use the Disk Pad to scroll down
to the
Tools menu.
2. In the
Tools menu, scroll down the pop-up list to Usage/Hrs to display the total operating time of the
lamp.
3. Select
Lamp Reset from the next pop-up list.
4. Select
Exit.
Note: Do not reset the lamp hours if the lamp cartridge was not changed. This can damage internal
components.
Maintenance
34
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
Replacing ProjectionScreen
Replacing the 3M Digital WallDisplay screen is very simple.
1. Turn off the 3M Digital WallDisplay and disconnect the power cord from the wall outlet.
2. Remove the right and left side bezels. There are two ways to remove it. Either snap it off or insert a screwdriver into the notch located on the sides of each bezel, near the top. The bezel will easily snap on and off for screen replacement.
3. Slide the screen straight out of the open side. Be sure to allow approximately 4 feet of clear space on either side of the 3M Digital WallDisplay to do this.
4. Insert new screen into the open side and slide into place. Ensure that the screen is centered before replacing the side bezels. The bezels have ribs on the inside that could damage the screen if it is not centered.
5. Insert the bottom of the bezel first, then snap bezel back into place.
35
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
3M Digital WallDisplay Troubleshooting
Common Problems and Solutions
Continued on next page
Symptom
Power cannot be turned on.
No picture or sound.
The lamp will not ignite or has turned off.
The projection arm opens, then closes.
Sound is heard with no picture.
Picture is displayed with no sound.
Picture is dark.
Cause
The power cord is disconnected. The
Master Power Switch is not
turned on. The arm facade is not in place.
The desired input source is not selected.
The cables from the input source are not connected.
The input source is not turned on or not displaying an image. (e.g. If a notebook computer, the external monitor port is not turned on.)
The internal temperature is too high. The lamp has reached maximum life or
has prematurely failed.
The lamp will not ignite.
The VGA/Video cables are not connected. The VGA/Video/Audio cables are connected to the wrong input.
The VGA/Video cables are not connected.
The audio cables are connected to the wrong input.
The volume is set to Minimum. The
Mute is on.
The
Colorful—Bright setting must be
adjusted. The lamp needs to be replaced.
Solution
Insert the power cord into an AC socket.
Turn on the
Master Power Switch.
Make sure the arm facade is in place.
Press the remote control Input button to select a desired input source.
Connect the cable to correct input source.
Turn on input source.
Clear blocked ventilation holes. Replace lamp.
Replace lamp.
Connect the cables to the correct input source.
Connect the cables to the correct input source.
Turn up
Volume.
Turn off
Mute.
Adjust
Colorful—Bright slider
setting. Replace lamp.
Troubleshooting
36
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
Common Problems and Solutions, continued
Onscreen Messages
Symptom
Desired input source cannot be detected.
The remote control does not work.
The menu system will not display.
Cause
The input source is not active. A signal must be present for the input to be selected.
The input device (e.g. computer, VHS player, etc.) is not turned on.
The remote control is not facing the remote control sensor.
The remote control is too far from the sensor.
An obstruction is between the remote control and the sensor.
The remote control’s batteries are exhausted.
The menu system will not display without an input source displayed.
Solution
Connect an active input source to unit.
Turn on input source.
Face the remote control toward the remote control sensor.
Operate the remote control within 5 meters.
Remove obstacle.
Replace batteries.
Connect an active input source to unit.
Message
No input is detected
Please change the lamp
There are (x) hours of lamp life remaining The WallDisplay will shut off in 40 minutes
There are (x) hours of lamp life remaining The WallDisplay will shut off in 5 minutes
Meaning
3M Digital WallDisplay is not receiving a signal from an external source. Check the cable connections and verify power is on and external source is working.
The lamp has 1400-1499 hours on it and needs to be changed.
The lamp has 1500-1579 hours on it and needs to be changed.
When the lamp has 1580 hours or more on it, the message will flash, and the power will turn off after 5 minutes.
37
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH

Service Information

Replacement Parts
Description Part Number
Power Cord (EU) 78-8131-0004-3 Power Cord (US) 78-8131-0005-0 Power Cord (UK) 78-8131-0003-5 Serial Mouse Cable 26-1015-0423-6 USB Cable 26-1015-0424-4 VGA Cable 26-1015-0425-1 DVI-D Cable 26-1015-0418-6 PC Audio Cable 26-1015-0420-2 S-Video Cable 26-1015-0422-8 Replacement Lamp 78-6969-9692-1 Remote Control Unit 78-8121-0330-3 Macintosh Adapter 26-1015-0419-4 3-Conductor Video/Audio Cable 26-1015-0421-0 Dry-Erase Screen 78-6969-9470-2 3M Vikuiti High Brightness Screen 78-6969-9471-0
Optional Accessories
Accessory Tray (right side) 78-6969-9371-2 Accessory Tray (left side) 78-6969-9472-8 Easy Erase Screen 78-6969-9469-4
Ordering Parts or Getting Information
For product information, product assistance, service information, or to order accessories, please contact 3M Customer Service at the following numbers:
• In U.S. or Canada:
1-800-328-1371
• In other locations, contact your 3M Sales office.
The contents of this manual are subject to change without prior notice. 3M assumes no responsibility for the infringement of special rights of a third party or other rights that may arise out of the
information contained in this manual. Reproduction of this manual in any form without prior permission is strictly prohibited.
38
3M™ Digital WallDisplay
ENGLISH

Appendix

3M™ Digital WallDisplay Specifications
eziSyalpsiDaeraelbaweivlanogaiD 06
oitaRtcepsAyalpsiD3:4
metsySyalpsiD ygolonhcetstnemurtsnIsaxeTPLD,pihCelgniS
eziSlanogaiDpihChcni7.0
pihCPLD
slexiPforebmuNslexip867x4201
roloCroloclluftib-42
oitaRtsartnoC1:051
epyT)erusserPhgiH-repuS(PHS
pmaL
efiLsruoH0002
snoisnemiD
thgieW.sbl58.xorppA
ytilibitapmoCoediV MACES,M-LAP,N-LAP,LAP,34.4CSTN,CSTN
ytilibitapmoCoediVretupmoCAGXSotAGV
noitalumEesuoM BSUdna,BDA,esuomlairesCP
tupnIretupmoC
slangiS
tuptuO/tupnI
lanimreT
tuOoiduAskcajACR
slangistupnioediVnip-4NIDiniM:oediV-S
1000 hours
D 0.7xW 2.35xH 6.74
)mm971xmm0531xmm8021(
buS-Dinimnip-51:BGRgolanA
)ylnolatigid(D-IVD:BGRlatigiD
kcaj-inimoeretsmm5.3:oiduA
troPlortnoC232-SRbuS-Dnip-9
troPnoitalumEesuoMbuS-Dnip-9
20 Watts per channel
)srekaepsot(reifilpmAlennahcrepttaW81
metsySoiduA
srekaepSsmhO8,xaMsttaW04
stnemeriuqeRrewoP .xaMsttaW004,zH06/05,CAV042~001
©3M 2005. All Rights Reserved.
Appendix
39
3M™ Digital WallDisplay
©3M 2003. All Rights Reserved.
ENGLISH
Input/Output Signal Specifications
Computer Compatibility
Resolution Refresh Rate Horizontal
Frequency
640x400 85 Hz 37.9 kHz 640x480 60 Hz 31.5 kHz 640x480 72 Hz 37.9 kHz 640x480 75 Hz 37.5 kHz 640x480 85 Hz 43.3 kHz 800x600 56 Hz 35.1 kHz 800x600 60 Hz 37.9 kHz 800x600 72 Hz 48.1 kHz 800x600 75 Hz 46.9 kHz
800x600 85 Hz 53.7 kHz 1024x768 60 Hz 48.4 kHz 1024x768 70 Hz 56.5 kHz 1024x768 75 Hz 60.0 kHz 1024x768 85 Hz 68.7 kHz
1280x1024 60 Hz 64.0 kHz 1280x1024 75 Hz 80.0 kHz
1280x1024 85 Hz 91.1 kHz
langiSoediV
langiScnySlatnoziroH
retupmoC
oediV-S
oediV
langiSoediVsmhO57,p-pV0.1
langiScnySlacitreV
langiScnySetisopmoCleveLLTT
langiStupnIoiduA
langiStuptuOoiduAsmhOk1,smrVm002~0
langiStupnIoiduAsmhOk02,smrVm002
)ytiralop
)ytiralop
)p-pV0.3
smhO57
smhO
smhO57,p-pV7.0golanA
)ytiralopevitisop(noitanimret
evitagen/evitisop(leveLLTT
evitagen/evitisop(leveLLTT
xaM(smhOk02,smrVm002
,p-pV0.1:langisecnanimuL
:langisecnanimorhC
57,)tsrubroloc(p-pV682.0
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly set forth in a written agreement signed by an authorized officer of 3M.
Avis Important
Toutes les déclarations, l’information d’ordre technique et les recommendations afférentes aux produits 3M sont fondées sur des renseignements supposés exacts, mais la précision ou l’intégralité n’est pas garantie. Avant d’utiliser ce produit, vous devez l’évaluer afin de déterminer s’il est adapté aux applications que vous avez l’intention d’utiliser. Vous acceptez tous les risques et la responsabilité associés à une telle utilisation. Toutes les déclarations concernant le produit qui ne sont pas incluses dans les publications actuelles de 3M et toutes les déclarations contradictoires qui sont incluses sur votre bon de commande seront sans effet sauf accord explicite par écrit avec un cadre agréé de 3M.
Wichtiger Hinweis
Alle Angaben, technischen Informationen und Empfehlungen, die sich auf 3M-Produkte beziehen, sind nach bestem Wissen korrekt und zuverlässig, jedoch können wir keine Gewähr übernehmen. Vor der Anschaffung dieses Produkts sollten Sie sich davon überzeugen, das es für den vorgesehenen Einsatz tauglich ist. Alle aus der Verwendung des Produkts entstehenden Risiken und jegliche Haftung liegt bei Ihnen. Jegliche sich auf das Produkt beziehende Aussagen, die nicht aus einer aktuellen Veröffentlichung von 3M stammen bzw. jegliche im Kaufauftrag enthaltene gegensätzliche Aussagen sind ohne ausdrückliche schriftliche Genehmigung durch einen autorisierten Vertreter von 3M nicht gültig bzw. ohne Wirkung.
Aviso Importante
Todas las declaraciones, información técnica y recomendaciones relacionadas con los productos 3M está basada en informa­ción que se cree fiable, pero la preción o lo completo de éstas no está garantizado. Antes de utilizar este producto debe evaluar­lo y determinar si es adecuado para su aplicación. Usted asume todos los riesgos y la responsabilidades asociadas con dicho uso. Cualquier afirmación relacionada con el producto que no se encuentre en las publicaciones actuales de 3M, o cualquier afirmación contraria incluida en su orden de compra, carecerá de vigencia y efecto si no ha sido acordada expresamente, por escrito, por un funcionario autorizado de 3M.
Avviso importante
Tutte le dichiarazioni, le informazioni tecniche e i consigli relativi a prodotti 3M si basano su informazioni ritenute affidabili, ma la loro accuratezza o completezza non sono garantite. Prima di utilizzare questo prodotto, è necessario valutarlo e determi­narne l’idoneità per l’applicazione prevista. L’utente si assume tutti i rischi e le responsabilità associati a tale utilizzo. Qualsiasi dichiarazione relativa al prodotto che non sia riportata nelle pubblicazioni correnti della 3M o qualsiasi dichiarazione opposta riportata sull’ordine d’acquisto, non costituirà obbligo e non avrà alcun effetto, tranne se concordato esplicitamente con autor­izzazione scritta emessa da un rappresentante ufficiale della 3M.
3M Austin Center
Building A145-5N-01 6801 River Place Blvd. Austin, TX 78726-9000
3M Canada
P.O. Box 5757 London, Ontario N6A 4T1
3M Mexico, S.A. de C.V.
Apartado Postal 14-139 Mexico, D.F. 07000 Mexico
http://www.3M.com/walldisplay
3M Europe
Boulevard de l’Oise 95006 Cerge Pontoise Cedex France
Copyright © 2002 3M
Copyright © 2005 3M
All Rights Reserved
All Rights Reserved
78-6970-9074-0 Rev. C
78-6970-9184-7 Rev. C
Litho in USA
Litho in USA
Loading...