3M 2273M-iD, 2250M, 2273M, 2250M-iD User Manual

3M™ Dynatel™ Cable/Pipe/Fault Advanced Locator 2250M/2273M Series

(With 3-watt, 5-watt, or 12-watt Transmitter)

Operator’s Manual

2250M 2250M-iD 2273M 2273M-iD

June 2014

78-8130-6150-0 Rev G 3

Contents

1. Safety Information ............................................................................................ 6

A. Intended Use ................................................................................................ 6

2. About This Manual............................................................................................ 7

3. Quick Start ........................................................................................................ 8

A. Transmitter Battery Installation ................................................................... 8

B. Receiver Battery Installation ....................................................................... 9

C. Cleaning ..................................................................................................... 10

D. Service and Accessories .............................................................................10

E. 3M™ Dynatel™ Transmitter 2250 Keypad and Connector Denitions....10

F. 3M Dynatel Transmitter 2273 Keypad and Connector Denitions ............ 11

G. Maximum Transmitter Output ................................................................... 12

H. Rechargeable Battery ................................................................................. 12

I. 3M Dynatel Receiver 2250M Key Pad and Display Denitions ................ 13

J. 3M Dynatel Receiver 2273M Key Pad and Display Denitions ................ 14

4. Menu Displays ................................................................................................ 15

A. Main Menu ................................................................................................ 15

5. Conguring The Receiver ............................................................................... 18

A. Select Depth Units ..................................................................................... 18

B. Setting the Receiver Clock ........................................................................ 18

C. Selecting a Language ................................................................................. 18

D. Enabling/Disabling Frequencies ................................................................ 19

E. Selecting External Jack Frequencies (Tone Frequencies) .......................... 19

F. Creating User Dened Frequencies ............................................................ 19

G. Filtering Power Frequency Interference .................................................... 20

H. Selecting Locating Audio ..........................................................................20

6. Buried Cables And Pipes: Transmitter Connections ....................................... 21

A. Direct Connect Method ............................................................................. 21

B. Dyna-Coupler Method ............................................................................... 23

C. Induction Method ....................................................................................... 24

7. Receiver Modes .............................................................................................. 28

A. Directional Peak (Dir Pk) .......................................................................... 28

B. Directional Null (DirNull) ......................................................................... 28

C. Special Peak (Spl Pk) ................................................................................. 29

D. Induction Peak (Ind Pk) ............................................................................. 30

E. Expanded Mode ......................................................................................... 30

8. Depth and Current Estimate ............................................................................ 30

2 78-8130-6150-0 Rev G

9. Locating Frequencies ...................................................................................... 31

A. Active Frequencies .................................................................................... 31

B. Power Frequencies ..................................................................................... 32

C. Passive Frequencies ................................................................................... 32

D. Auxiliary Frequencies ................................................................................ 32

10. Locating in Directional Peak Mode .............................................................. 33

11. Locating Active Duct Probes (Sondes) ......................................................... 35

A. Determining ADP Depth ............................................................................ 35

12. Locating Buried Sheath Faults and Earth-Return Faults ............................. 36

A. Transmitter Setup ....................................................................................... 36

B. Pinpointing the Buried Fault ...................................................................... 37

13. Locating 3M™ Electronic Markers and 3M™ iD Markers ............................. 39

A. Enabling/Disabling Marker Types ............................................................. 39

B. Alert Mode ................................................................................................. 39

C. Single Marker Locate ................................................................................. 40

D. Dual Marker Locate ................................................................................... 41

E. 3M iD Marker Depth .................................................................................. 41

F. Passive Electronic Marker (Non-iD) Depth ............................................... 42

14. Creating/Editing Templates for 3M™ iD Markers ......................................... 43

A. Creating New Templates ............................................................................ 43

B. Editing Templates ......................................................................................45

15. Writing 3M iD Markers ................................................................................46

A. Modifying Marker Data to be Written ....................................................... 47

16. Reading 3M iD Markers .............................................................................. 48

17. Reviewing Marker Read/Write History ........................................................ 49

A. Read History .............................................................................................. 49

B. Write History [SK] ..................................................................................... 50

18. GPS Operation .............................................................................................. 50

A. Communicating with the GPS Device ....................................................... 51

B. Capturing the GPS Coordinates (Capture Mode / Mode 1) ....................... 51

C. Sending 3M iD Marker Data to GPS (Capture-Transmit Mode / Mode 2) 52

D. Path Mapping with GPS ............................................................................ 52

78-8130-6150-0 Rev G 3

19. Additional Applications ................................................................................ 53

A. Aerial Faults (Toning) ................................................................................ 53

B. Cable Identication .................................................................................... 55

20. Help Mode .................................................................................................... 56

21. 3M™ Dynatel™ PC Tool Kit and Locator Software Upgrades ....................... 56

22. Self Test Of Receiver .................................................................................... 57

23. Product Description And Optional Accessories ............................................ 57

A. Product Description ................................................................................... 57

B. Standard Congurations ............................................................................ 58

C. Optional 3M™ Accessories for 3M Dynatel™ Locators .............................. 59

24. Receiver Specications ................................................................................. 60

25. Transmitter Specications .............................................................................62

26. Environmental and Regulatory Specications .............................................. 63

27. Rechargeable Battery Information ................................................................ 63

4 78-8130-6150-0 Rev G

Congratulations! You have just purchased one of the finest, most advanced locating devices available today!

™

The 3M

Dynatel™ Cable/Pipe/Fault Locators 2250M-iD/2273M-iD are designed with all of the functionality of previous Dynatel models, and iD versions have the enhanced capability to read and write user information into the 3M iD markers. Information such as a pre-programmed identification number, facility data, application type, placement date and other details can all be read, stored and downloaded to your PC for enhanced resource management with this revolutionary equipment. The Dynatel Cable/Pipe/Fault Locators 2250M-iD/2273M-iD will also search for two different types of utility markers simultaneously. When used in conjunction with a hand-held GPS device the ability to transmit path and marker coordinates multiplies the potential to the mapping industry. This equipment provides a simple system for mapping utility information directly into CAD and GIS systems.

The 2250M/2273M Series transmitters are available in 3-watt, 5-watt and 12-watt units. 12 watts for the 12-watt transmitter, or 5 watts for the 5-watt transmitter, is attained by utilizing the Cigarette Lighter Adapter or External Rechargeable Battery (2200RB).

3M is dedicated to bringing you premium equipment with outstanding reliability, backed by one of the best warranties in the business and outstanding service.

Visit our website at www.3M.com/dynatel for more application notes and product information.

78-8130-6150-0 Rev G 5

1. Safety Information

Please read, understand and follow all safety information contained in these instructions prior to the use of the 3M™ Dynatel™ Cable/Pipe/Fault Advanced M-Series Locator. Retain these instructions for future reference.

A. Intended Use

The 3M Dynatel Cable/Pipe/Fault Advanced M-Series Locator is used to identify the placement of underground utility lines. The system must be installed as specified in the 3M Dynatel Cable/Pipe/Fault Advanced Locator 2250M/2273M Series Operator Manual. It has not been evaluated for other uses or locations. If this equipment is used in a manner not specified by 3M, the protections provided by the equipment may be impaired.

Explanation of Signal Word Consequences

! Warning:

! Caution:

Indicates hazardous situation which if not avoided, could result in death or serious injury.

Indicates hazardous situation which if not avoided, could result in minor or moderate injury.

Explanation of Product Safety Label Symbols

Do not throw away in normal trash.

! WARNING

This WARNING applies to the following 3M Dyna-Couplers;

• 3" (75 mm) - Part number 3001

• 4.5" (114 mm) - Part number 4001

• 6" (150 mm) - Part number 1196

• All accessory kits containing any of the listed Dyna-Couplers - Part numbers 3019, 4519, 1196/C

A potential for electrical shock exists when using the Dyna-Coupler on cables energized with

electrical power. Use appropriate safety procedures.

DO NOT USE ON CABLES CARRYING IN EXCESS OF 600 VOLTS RMS.

6 78-8130-6150-0 Rev G

Warning: Risk of electric shock

! WARNING

This WARNING applies to the use of the Direct Connect Cables and the Transmitter.

To avoid potential shock, or electrically damaging the Transmitter, when setting up the

Transmitter to locate using the Direct Connect method, follow these basic steps;

• ALWAYS plug the Direct Connect Cable into the Transmitter Output Jack [T-6] BEFORE

connecting the leads to the cable/pipe to be located and the ground rod. – Connect the red lead to the cable/pipe. – Connect the black lead to ground rod. A POTENTIAL FOR ELECTRICAL SHOCK, AND/OR TRANSMITTER ELECTRICAL DAMAGE, EXISTS

WHEN USING THE DIRECT CONNECT CABLE ON CABLES ENERGIZED WITH ELECTRICAL POWER IF THE ABOVE INSTRUCTIONS ARE NOT FOLLOWED. USE APPROPRIATE SAFETY PROCEDURES.

CHECK VOLTAGE BEFORE CONNECTING TRANSMITTER. VOLTAGE HIGHER THAN 240 VOLTS WILL DAMAGE EQUIPMENT. FOLLOW STANDARD PROCEDURES FOR REDUCING THE VOLTAGE.

2. About This Manual

There are two basic models included in the 3M™ Dynatel™ Locator 2200M Series. The 2250M locator is designed for cable/pipe locating. The 2273M locator is designed for cable/pipe and fault locating. The iD option (read/write capability to 3M is available for both models. There are three transmitter options: 3 Watt, 5 Watt, or 12 Watt. This instruction manual will include all features. All instructions are applicable to all products, unless noted.

The 12-watt transmitter option offers additional power output levels for improved induction performance and 8 kHz (low frequency) induction for shallow facilities, such as risers. Output Power up to 12 Watts for the 12-watt transmitter is achieved using the supplied external power source. The maximum output power in Direct Connect method is reduced to below FCC limits. (FCC limits: 1 Watt at 200 kHz and 10 Watts at 33 kHz)

In order to demonstrate all available functions, the illustrations depict the 2273M-iD receiver unit and the 2250 and 2273 12-watt transmitters. The 2250M receiver may vary from the illustrations shown.

iD Markers)

78-8130-6150-0 Rev G 7

3. Quick Start

A. Transmitter Battery Installation

Loosen the six screws on the battery compartment cover on the bottom of the transmitter. Remove the cover.

Install six ‘C’ size alkaline cell batteries (LR14) into the compartment as indicated by the polarity symbols (+ and –).

Replace the cover and tighten the screws.

6 'C' (LR14) size

Alkaline Batteries

Press and hold OFF [T-1] to manually test the batteries. The display and audio will indicate one of the following levels: (OK w/solid tone = good; LO w/beeping tone = low; "--" w/no tone = replace)

! Caution

To reduce the risks associated with ﬁre and explosion:

• Do not short, excessively heat, or dispose of batteries in re.

• Install batteries with proper polarity.

• Use only Alkaline "C" (LR14) sized batteries.

• Do not charge batteries

• Do not use leaking batteries

To reduce the risks associated with environmental contamination:

• Dispose of batteries and electronic components in accordance with all regulations.

• Ensure batteries are installed with correct polarity.

• Always remove batteries when storing the units for long periods of time.

8 78-8130-6150-0 Rev G

B. Receiver Battery Installation

Remove cap from receiver handle.

Install eight ‘AA’ size alkaline cell batteries (LR6) into the battery holder as indicated by the polarity symbols (+ and –).

Attach battery holder to the PP3 connector in the receiver handle, and slide holder into the handle. Replace the cap.

8 “AA” (LR6) Alkaline Batteries

1. Twist cap to open battery

compartment.

2. Slide battery compartment

out of handle.

! Caution

To reduce the risks associated with ﬁre and explosion:

• Do not short, excessively heat, or dispose of batteries in re.

• Install batteries with proper polarity.

• Use only Alkaline "AA" (LR 6) sized batteries.

• Do not charge batteries

• Do not use leaking batteries

To reduce the risks associated with environmental contamination:

• Dispose of batteries and electronic components in accordance with all regulations.

• Ensure batteries are installed with correct polarity.

• Always remove batteries when storing the units for long periods of time.

The receiver batteries are tested for two seconds every time the unit is turned on.

The bar graph on the display will fill to the relative battery level.

78-8130-6150-0 Rev G 9

The Battery Icon [8] on the Locating Displays will continuously indicate the battery level.

C. Cleaning

Use a soft damp cloth to clean the product and test leads if necessary.

D. Service and Accessories

Information regarding service, accessories, or replacement parts can be obtained by contacting 3M at 1-800-426-8688.

This equipment does not require annual calibration or maintenance.

E. 3M™ Dynatel™ Transmitter 2250 Keypad and Connector Definitions

Dynatel

off on

T-1 T-2 T-3 T-5 T- 6 T-7

[T-1] off: Turns unit off and performs battery test.

[T-2] on: Ohm-meter / Tone: Turns the unit on and cycles through the following

commands when pressed repeatedly.

Ohm-meter: Measures the continuity of the trace conductor/pipe and its far-end ground. It is also used to measure the fault resistance to earth.

Tone: In the tone mode, the transmitter generates 577 Hz and 200 kHz signals.

[T-3] on: Trace (frequency): Turns the unit on and places the unit in Trace mode.

Select Frequency: Press Trace [T-3] repeatedly to cycle through the transmitter’s

active frequencies (577 Hz, 8 kHz, 33 kHz, and 200 kHz). The selected frequency will be displayed [T-4]. ‘ALL' indicates that the following active frequencies are transmitting simultaneously: 577 Hz, 8 kHz, 33 kHz, and 200 kHz.

[T-4] Digital Display:

Indicator Flags: These flags coincide with the operational mode of the transmitter. (From top left to bottom right) Trace mode [T-3], Tone mode [T-2], Ohm-meter [T-2], Voltage (at start up the transmitter checks for foreign voltage), and the Output Level Flag (no flag = normal output; flag = high output; flashing flag = maximum output).

Digital Display: Indicates frequency, relative current, resistance, battery level and voltage (if present on target).

[T-5] Output Level: Cycles output level; normal, high and maximum.

Normal=No Flag; High=Flag; Maximum=Flashing Flag (indicated in Digital Display [T-4])

NOTE: An external 12-volt power source is required to obtain Max Output level (12 watts for 12-watt transmitters and 5 watts for 5-watt transmitters).

2250

Trace

Output Level

10 78-8130-6150-0 Rev G

NOTE: 12 Watt Output Level varies by frequency. Output is limited to 10 watts at 33 kHz and 1 watt at 200 kHz using the direct connection method.

[T-6] Output Jack: Port for direct connect cables or Dyna-coupler.

[T-7] External Jack: Port to connect cigarette lighter adapter cable, or rechargeable

battery (2200RB). Input voltage level: 9-18 VDC. (Only on 5-watt and 12-watt transmitters.)

F. 3M™ Dynatel™ Transmitter 2273 Keypad and Connector Definitions

T-1 T-2 T-3 T-4 T-5 T-7

[T-1] off: Turns unit off and performs battery test.

[T-2] on: Ohm-meter / Fault Locate / Tone: Turns the unit on and cycles through the

following commands when pressed repeatedly.

Ohm-meter: Measures the continuity of the trace conductor/pipe and its far-end ground. It is also used to measure the fault resistance to earth.

Fault Locate: (2273M units only) In this mode, the transmitter sends two alternating locating frequencies (577 Hz and 33 kHz) as well as fault signals 10 and 20 Hz.

Tone: In the tone mode, the transmitter generates 577 Hz and 200 kHz signals.

[T-3] on: Trace (frequency): Turns the unit on and places the unit in Trace mode.

Select Frequency: Press Trace [T-3] repeatedly to cycle through the transmitter’s

[T-4] Digital Display:

Indicator Flags: These flags coincide with the operational mode of the transmitter. (From top left to bottom right) Fault mode [T-2] (2273 units only), Tone mode [T-2], Trace mode [T-3], Ohm-meter [T-2], Voltage (at start up the transmitter checks for foreign voltage), and the Output Level Flag (no flag = normal output; flag = high output; flashing flag = maximum output).

Digital Display: Indicates frequency, relative current, resistance, battery level and voltage (if present on target).

[T-5] Output Level: Cycles output level; normal, high and maximum.

Normal=No Flag; High=Flag; Maximum=Flashing Flag (indicated in Digital Display [T-4])

NOTE: An external 12-volt power source is required to obtain Max Output level (12 watts for 12-watt transmitters and 5 watts for 5-watt transmitters).

78-8130-6150-0 Rev G 11

NOTE: 12 Watt Output Level varies by frequency. Output is limited to 10 watts at 33 kHz and 1 watt at 200 kHz using the direct connection method.

™

[T-6] Output Jack: Port for direct connect cables or 3M

[T-7] External Jack: Port to connect cigarette lighter adapter cable, or rechargeable

battery (2200RB). Input voltage level: 9-18 VDC. (Only on 5-watt and 12-watt transmitters.)

Dyna-coupler.

G. Maximum Transmitter Output

An external 12V DC source is required for 12-Watt Output (Max setting) using a 12-watt transmitter or 5 watt output (Max setting) using a 5-watt transmitter. Connecting the rechargeable battery (2200RB) to the External Jack [T-7] will provide this external source, or the cigarette lighter adapter cable (included with 12-watt and 5-watt transmitters) can be used to connect the DC power from a vehicle’s battery source to the transmitter’s External Jack [T-7].

Press Output Level [T-5] twice for maximum output mode.

The indicator flag will flash when the transmitter is in maximum output mode.

Note: The external DC source does not charge the internal batteries.

! WARNING

To reduce the risk associated with hazardous voltage:

• Potential for electric shock exists when handling connection cables while the transmitter is

ON. Make all connections prior to powering on the unit. Turn transmitter OFF before handling connection cables.

• Voltage greater than 240 volts will damage equipment and could cause personal injury or

death. Make all connections before turning on the transmitter. Follow standard procedures

for reducing the voltage.

• Do not change or modify this product in any way.

H. Rechargeable Battery

The 3M™ Dynatel™ Sealed Gel-Cell Battery 2200RB can be used as an auxiliary battery in 3M™ Dynatel™ Transmitters 2200 Series. It plugs into the External Jack [T-7] and provides power for the transmitter. When the rechargeable battery is plugged in, normal output, high output, and maximum output are available. When the rechargeable battery is connected to the transmitter, the alkaline batteries are bypassed. The rechargeable battery is a lead acid battery rated at 5.4 amp-hours and is equipped with a user replaceable fuse (5A/32V).

Note: The internal batteries must be at least 5.4 volts. Do not remove the alkaline batteries from the transmitter when using the rechargeable battery. Rechargeable battery, or cigarette lighter adapter cable, is required for Maximum output level.

Rechargeable battery is shown installed in the well of the transmitter case.

12 78-8130-6150-0 Rev G

I. 3M™ Dynatel™ Receiver 2250M Key Pad and Display Definitions

8 2A

1 6

2 5

Dynatel

2250M Cable/Pipe Locator

On/Off

Spkr/Xpnd

™

Gain Adjust

Locate

11 12

9 SK

Access panel on bottom side of Receiver under

rubber cover.

[1] On/Off (Power): Turns unit on and off.

[2] Speaker Volume Control: Adjusts the volume of the receiver (off, low, med, high,

and Xpand).

[2A] Speaker Volume Icon: Indicates the relative volume level of the receiver. When the third ring is dotted and ‘xpnd' appears below the speaker icon, the receiver is in “Expander” mode. This mode is used to pinpoint the target cable or pipe.

[3] Contrast: The arrows located above and below the contrast icon will adjust the contrast of the display.

[4] Gain Adjust: Adjusts the sensitivity of the receiver either up or down to maintain a satisfactory signal level.

[5] Locate/OK: Sets the receiver to trace mode for locating Cable/Pipe, Markers (for iD units only), Tone. Tone/Ext is used to activate the External Jack [13]. Acknowledges setup entries (OK).

[6] Menu: Displays setup screen for configuration of the unit, i.e.: clock, language, depth units, marker data and frequencies.

[7] Backlight: Toggles the backlight low, high, and off.

[8] Battery Icon: Indicates battery level.

[SK] Soft Keys: There are four soft keys (yellow keys) on the receiver. The function

of each key is shown above the yellow key on the display screen. The functions will change, depending on the operation mode of the receiver. For instruction purposes in this manual, the display command is followed by [SK] to identify it as a soft key.

[9] Soft Key Commands: Definitions for each of the four soft key functions.

[10] Signal Strength: Digital reading of the signal that the receiver is detecting from the

target.

[11] Bar Graph: Graphical representation of the received signal.

[12] Gain Level: Displays relative gain level.

[l3] External Jack: Port to connect cables from external devices such as the earth frame

(A-Frame), a second 3M Dyna-Coupler, or a toning coil.

[14] Serial Port: RS232 port to connect the receiver to a PC via serial cable or USB-toserial adapter cable.

78-8130-6150-0 Rev G 13

[15] Earphone Jack: Will fit standard 1/8" (3.175 mm) mini-jack mono earphone plug (not included).

J. 3M™ Dynatel™ Receiver 2273M Key Pad and Display Definitions

Access panel on bottom side of Receiver under

rubber cover.

[1] On/Off (Power): Turns unit on and off.

[2] Speaker Volume Control: Adjusts the volume of the receiver (off, low, med, high,

and Xpand).

[3] Contrast: The arrows located above and below the contrast icon will adjust the contrast of the display.

[4] Gain Adjust: Adjusts the sensitivity of the receiver either up or down to maintain a satisfactory signal level.

[5] Locate/OK: Sets the receiver to trace mode for locating Cable/Pipe, Markers (for iD units only), Fault Finding, Tone. Tone/Ext is used to activate the External Jack [14]. Acknowledges setup entries (OK).

[6] Menu: Displays setup screen for configuration of the unit, i.e.: clock, language, depth units, marker data and frequencies.

[7] Backlight: Toggles the backlight low, high, and off.

[8] Battery Icon: Indicates battery level.

[SK] Soft Keys: There are four soft keys (yellow keys) on the receiver. The function

[9] Soft Key Commands: Definitions for each of the four soft key functions.

[10] Signal Strength: Digital reading of the signal that the receiver is detecting from the

target.

[11] Bar Graph: Graphical representation of the received signal.

[12] Gain Level: Displays relative gain level.

14 78-8130-6150-0 Rev G

[13] Fault Finding Direction Indicators: Corresponds to the Earth Contact Frame (A-Frame) probe (leg) colors.

[l4] External Jack: Port to connect cables from external devices such as the earth frame (A-Frame), a second 3M

[15] Serial Port: RS232 port to connect the receiver to a PC via serial cable or USB-toserial adapter cable.

[16] Earphone Jack: Will fit standard 1/8" (3.175 mm) mini-jack mono earphone plug (not included).

™

Dyna-Coupler, or a toning coil.

4. Menu Displays

A. Main Menu

When the Menu [6] button is pressed, the Main Menu display appears.

The function appears on the display above each soft key.

1. Write Mode: System used to write information to 3M iD Markers

2. Data/Template: Displays marker history and

template creation/selection displays:

a. Read History – 100 memory locations for

Read iD Markers

b. Write History – 100 memory locations for

Written iD Markers

c. User Templates – Create and edit iD

templates for iD Markers (max = 32)

d. Trace Templates – Create and edit

templates used to identify path (max = 5)

78-8130-6150-0 Rev G 15

3. COM Setup: Displays second level COM Port setting display to configure RS232 port communication with different devices –

a. PC – Receiver will communicate to a

computer

b. NMEA – Port is configured to accept

coordinates from GPS device

c. GIS – Port is configured to send 3M

™

marker information or path information to GPS device and receive coordinates from GPS device.

d. PDA – receiver will send 3M iD marker and

path information in ASCII string.

4. >>More: Advances to next menu display

5. <<Back: Returns to previous menu display

6. Setup: Displays second and third level displays for receiver configuration

a. Depth Units – Choose unit of measure; in,

ft-in, or cm

b. Clock – Date and time stamped on marker

information and depth readings.

c. Language – Toggles between English and

alternate language

d. >>More - Advances to next menu display

16 78-8130-6150-0 Rev G

e. <<Back - Returns to previous display

f. Marker Type – enable and disable marker

utility types

g. Locate Frequencies – enable and disable

receiver frequencies for locate mode

h. >>More - Advances to next menu display

i. <<Back - Returns to previous display

j. Tone/Freq - External Port or Tone

Frequencies – enable and disable frequencies that are detectable through the external port of the receiver

k. Power Filter Frequency – Select the power

frequency of the region to aid in 50/60 Hz interference rejection when using Auxiliary frequencies

l. Audio Configuration – Select audio

response of unit for Directional Peak mode

7. Self Test: Displays information about receiver unit and performs a self check test

8. Help: Offers the user basic on-screen instructions

78-8130-6150-0 Rev G 17

5. Configuring The Receiver

In the setup mode, the units of depth measurement, time, date, and date format can be set. The receiver can be configured to detect only certain frequencies and/or specific utility markers (3M frequencies can be programmed, language of the receiver can be selected, and tone frequencies set.

A. Select Depth Units

MENU [6] + >>More [SK:4] + Setup [SK:6] + Units [SKToggle:6a]

1. Press Units [SK toggle:6a].

2. The soft key command will toggle between inches (in), centimeters (cm), and feet/inches (ft-in).

3. Press Locate/OK [5].

B. Setting the Receiver Clock

Set the time, date, and date format of the receiver. Depth and Current measurements are time and date stamped, as well as read write marker information (iD units only).

MENU [6] + >>More [SK:4] + Setup [SK:6] + Clock [SK:6b]

1. Press the left/right arrow [SK] to highlight the digit of the date or time to change.

2. Press the + or - [SK] to increment or decrement.

3. When the date format is highlighted, the format will toggle between mm/dd/yy and dd/mm/yy.

4. Press Locate/OK [5] to save, or Menu [6] to cancel.

™

Dynatel™ Receivers 2250M-iD and 2273M-iD only). User defined

C. Selecting a Language

MENU [6] + >>More [SK:4] + Setup [SK:6] + Lang [SKToggle:6c]

The soft key command will cycle through available languages. Press Locate/OK [5]. Alternate languages can be uploaded to the receiver using the 3M Software. The 3M www.3M.com/dynatel under the Software section; 2550/2573/2250M/2273M/1420 Locator PC Tools xx.x.x (EXE xx.xMB).

18 78-8130-6150-0 Rev G

™

Dynatel™ PC Tool Kit Software is available free of charge at

™

Dynatel™ PCTools

D. Enabling/Disabling Frequencies

MENU [6] + >>More [SK:4] + Setup [SK:6] + >>More [SK:6d] + Locate Freq [SK:6g]

The user can select the frequencies that the receiver will detect. All the available frequencies are listed in four groups (Left to Right: Active, Power, Passive, and Auxiliary). The Auxiliary group also contains the User Defined Frequencies. (See Creating User Defined Frequencies, Section 5F.)

1. Press the right arrow [SK] to move the highlight bar to the section of frequencies to enable, or disable.

2. Press the up/down arrows [SK] to highlight the specific frequency.

3. Press Enabl/Disabl [SK]. (Enable denoted by )

4. Repeat steps 2 & 3 to enable/disable other frequencies.

5. Press Locate/OK [5] to save.

E. Selecting External Jack [14] ([13] on 2250M locator) Frequencies (Tone Frequencies)

MENU [6] + >>More [SK:4] + Setup [SK:6] + >>More [SK:6d] + Tone Freq [SK:6j]

A coupler can be plugged into the External Jack [14] ([13]) on 2250M locator) of the receiver and used to identify cables. (See Additional Applications: Cable Identification, Section 19B.) The same procedure as D. Enabling/Disabling Frequencies (above) is followed for selecting frequencies that can be detected by the External Jack [14] ([13]) on 2250M locator) found on the bottom of the receiver.

F. Creating User Defined Frequencies

MENU [6] + >>More [SK:4] + Setup [SK:6] + >>More [SK:6d] + Locate Freq [SK:6g]

There are four user defined frequencies available on the receiver. (These frequencies must be between 50 Hz and 999 Hz.) These frequencies are found in the column on the far right of the Locate Freq display (Auxiliary frequencies). These frequencies, once programmed, will appear in the Locate mode under the Aux [SK] frequency list when Freq [SK] is selected in the Locate mode.

78-8130-6150-0 Rev G 19

To program the user defined frequencies press the right arrow [SK] to highlight the Auxiliary group of frequencies. Press the up/down arrows [SK] to highlight the user frequency to program. Press Enabl/Disabl [SK].

Press the left/right arrows [SK] to move the square cursor to a digit. Press Select [SK] to enter the number in the frequency field.

Press Locate/OK [5] to save the programmed frequency, or press Exit [SK] to cancel. The frequency will appear in the locate frequency display as U ###, where ### represents the selected frequency.

Note: To redefine a previously programmed user frequency, highlight the frequency, press enabl/ disabl, select the back arrow with the cursor, and press select to delete the previous entry.

G. Filtering Power Frequency Interference

MENU [6] + >>More [SK:4] + Setup [SK:6] + >>More [SK:6d] + >>More [SK:6h] + Filter[SK:6k]

In order to filter out unwanted power influences while locating with user-defined frequencies, verify the correct frequency is selected for your location (default is 60 Hz). Press Locate/OK [5].

H. Selecting Locating Audio

MENU [6] + >>More [SK:4] + Setup [SK:6] + >>More [SK:6d] + >>More [SK:6h] + AudioConfig [SK:6l]

The user can choose the audio response of the receiver when using the Directional Peak mode for path locating. Highlight the audio selection and press Locate/OK [5] to save.

20 78-8130-6150-0 Rev G

+ 46 hidden pages