ZyXEL WAP7205 Quick Start Manuals

If your broadband modem or router doesn't support MoCA, use an Ethernet cable

to connect the modem or router to a MoCA adapter and then use a coaxial cable

to connect the adapter to a coaxial outlet in your home.

The WAP7205 then automatically sets up a MoCA network with the router and can

access the Internet through the router.

ENGLISH

AC1300 Gigabit Ethernet MoCA Extender

WAP7205

Quick Start Guide

Scenario 1 - Connect to a MoCA Router Scenario 2 - Connect to a General Router with a MoCA Adapter

If you have a MoCA router which is connected to the Internet, use a coaxial cable

to connect the router's MoCA port to a coaxial outlet in your home.

The WAP7205 then automatically sets up a MoCA network with the router and can

access the Internet through the router.

5-A

North America USA

+ 1 800 255 4101 support@zyxel.com

EU Importer

Zyxel Communications A/S Generatorvej 8D, 2860 Søborg, Denmark. http://www.zyxel.dk

US Importer

Zyxel Communications, Inc 1130 North Miller Street Anaheim, CA 92806-2001 http://www.us.zyxel.com

Support Information

Plug the included power adapter into the POWER socket and then into a power

outlet.Make sure the power switch is set to the ON position.

Use an Ethernet cable to connect a LAN port of the WAP7205 to your computer or an

IP set-top-box.

Use a coaxial cable to connect the WAP7205's MoCA port to a coaxial outlet in your

home.

5-B

See the User's Guide at www.zyxel.com for more information, including customer support and safety warnings.

Room 1

Room 2

Coaxial Outlet

Hardware Connection

MoCA

MoCA Router

MoCA AdapterGeneral Router

5-A 5-B

Room 1

Room 2

Coaxial Outlet

LAN

OUTIN

The LED turns static WHITE.

around

minutes

POWER

Coaxial Outlet

MoCA

Wait until the LED turns static WHITE (around 2 minutes).

WAP7205

POWER

2.4G/5G

MoCA

The LED turns on and then blinks white after the device is powered on. It turns static on again when the system is ready.

The LED turns static white when the 2.4 GHz or 5 GHz WiFi network is enabled.

The LED turns static white when the MoCA port is connected and the WAP7205 successfully connects (MoCA) to another MoCA device.

POWER ON

WAP7205

Desktop Installation

Connect the stand carefully as shown.

Place the WAP7205 with the stand on a ﬂat surface.

Wall Mounting

Remove the cover of the wall mounting holes.

Drill two holes at a distance of 57 mm from each other and insert the masonry plugs

and screws.

Align the wall mounting holes on the WAP7205 with the screws on the wall. Hang the

WAP7205 on the screws.

Open Web Browser

Follow eaZy123 setup wizard

WAP7205

User

Password

admin

XXXXXXXXXXXXXX

User Name: admin Password:

(Refer to the belly label)

http://zyxelsetup (Windows)

http://zyxelsetup.local (MAC)

eaZy 123 Setup

Safety Warnings - English

Humid、dusty and extreme environment in which place the product and obstructing the

device ventilation slots are prohibited, any kind of conditions above may harm your

device.

There is a remote risk of electric shock from lightning.

(1) do not use the device outside, and make sure all the connections are indoors.

(2) do not install, use, or service this device during a thunderstorm.

Connect only suitable accessories to the device; make sure to connect the cables to the

correct ports.

Do not open the device, opening or removing covers can expose you to dangerous high

voltage points or other risks please, contact your vendor for further information.

Place connecting cables carefully so that no one will step on them or stumble over them

and disconnect all cables from this device before servicing or disassembling.

Please use the provided or designated connection cables/power cables/ adaptors.

connect it to the right supply voltage (for example, 110V AC in North America or 230V AC

in Europe), If the power adaptor or cord is damaged, it might cause electrocution.

remove it from the device and the power source , repairing the power adapter or cord is

prohibited , Contact your local vendor to order a new one.

Risk of explosion if battery is replaced by an incorrect type, dispose of used batteries

according to the instruction.

Please refer to the device back label, datasheet or box speciﬁcations catalog informa-

tion for rated power of device and operating temperature.

The socket-outlet shall be installed near the device, and shall be easily accessible

because it serves as the main disconnecting device.

European Union - Disposal and Recycling Information

The symbol below means that according to local regulations your

product and/or its battery shall be disposed of separately from domestic

waste. If this product is end of life, take it to a recycling station designat-

ed by local authorities. At the time of disposal, the separate collection of

your product and/or its battery will help save natural resources and

ensure that the environment is sustainable development.

Device Conﬁguration

Open a web browser and enter "http://zyxelsetup" (for Windows PC) or "http://zyxel-

setup.local" (for MAC PC), then log in with the default user name (admin) and

password (default pre-shared key).

Start the eaZy123 setup wizard.

Wireless Name (SSID)

Wireless Password (WPA2)

Apply

XXXXXXXXXXX

/ No WPS

WiFi Connection

Remove the cover of the wall mounting holes to see the WAP7205's default SSID and

Wi-Fi key.

Use the SSID and WiFi Key to connect your wireless enabled devices to the WAP7205.

Open your web browser and make sure you can surf the Internet.

1 1 2

1 2 3

Desktop Installation

Wall Mounting

57mm

/ Using WPS

The LED turns static WHITE.

static WHITE

LED Behavior

WiFi Connection

Amber Blinking

Press for 1 second.

Press the WPS button on your WAP7205 for 1 second.

Within 2 minutes, press the connect button on your WiFi client.

The WAP7205 WiFi LED starts to blink amber and then turns static WHITE when the

WPS process completed.

Note: If WPS failed and the WiFi client couldn't connect to the WAP7205, go to the

next section (WiFi Connection - No WPS).

WPS ON

SSID (2.4GHz)

Zyxelxxxxxx

SSID (5GHz)

Zyxelxxxxxx_5G

Pre-Shared key

XXXXXXXXXXXXX

SSID (2.4GHz) SSID (5GHz) Pre-Shared Key

within

minutes

Wi-Fi

Zyxelxxxxxx

Connect

2.4G/5G

Static white: The WiFi network is enabled.

Blinking white: Data is being sent or

received through the WiFi network.

White off: The WiFi network is disabled.

Blinking amber: WPS process is in progress.

Amber off: WPS process completed, WPS

connection failed or WPS is disabled

Default login address: http://zyxelsetup User name: admin Password: Pre-Shared Key

ZyXEL WAP7205 Quick Start Manuals

Specifications and Main Features

Frequently Asked Questions

User Manual