Zyxel VANTAGE REPORT installation guide
Vantage Report
Quick Start Guide
Version 3.0
10/2006
Edition 1
ENGLISH 3
DEUTSCH 23
ESPAÑOL 45
FRANÇAIS 67
ITALIANO 89
РУССКИЙ 111
简体中文
繁體中文 151
133
Copyright © 2006. All rights reserved.
ENGLISH
Vantage Report
Vantage Report collects log entries and traffic statistics from ZyXEL devices and then generates
graphical and tabular reports about network performance and events.
C
A
Install Vantage Report on the Vantage Report server (B). Then, use the web configurator (A) to
configure it. (The web configurator can run on a remote computer or on the Vantage Report
server.) Finally, configure the ZyXEL devices (C) to send their log entries and traffic statistics to
the Vantage Report Server. The Vantage Report server collects this information and builds
statistical reports about the network. You and others can look at these reports any time in the
web configurator or in regular e-mail messages.
B
Overview
1 Preparation - Make sure the Vantage Report server meets the minimum requirements, and
get the Vantage Report server ready for installation.
2 Installation - Install Vantage Report on the Vantage Report server.
3 Login - Use the web configurator to access the Vantage Report server.
4 E-mail Setup - Set up the administrator e-mail address and SMTP mail server settings in
Vantage Report, and test the SMTP settings.
5 Registration - When you install Vantage Report, you get the basic version. You do not have to
register Vantage Report unless you want to get the trial version or upgrade to the full version.
(See section 5 for more information about versions.)
6 Device Setup - Set up the ZyXEL devices, and add them in the Vantage Report server.
1 Preparation
Check these things before you install Vantage Report.
3
ENGLISH
1.1 Check Minimum Requirements
If your Vantage Report server does not meet the minimum requirements, you should upgrade it or
use a different server that does meet the minimum requirements.
Number of registered devices CPU Free Hard Disk Space (GB)
<5 Pentium IV 2.6 GHz 10
<50 Pentium IV 2.6 GHz Twice the number of devices
50-100 Pentium IV 3.2 GHz or faster Twice the number of devices
Operating System Windows XP Professional, Windows 2000/2003 Server
Browser
(Running on Server or
Other Computer)
Other Requirements for
Featured Services
Internet Explorer 6.0 (Service Pack 1) or later on Windows
Mozilla 1.7.12 or later on Windows
Firefox 1.07 or later on Windows
1024 by 768 resolution
SMTP daemon
TCP port 3316 and UDP port 514
1.2 Upgrading from Vantage Report v2.3 or v2.3.1
Use this section to upgrade from Vantage Report v2.3 (2.3.05.61.00) to v2.3.1 (2.3.00.61.01).
Click System > About to view your version details. Then use it again to upgrade from v2.3.1 to
v3.0. If you are already using v2.3.1, use this section to upgrade to v3.0.
1.2.1 Backup Your Data
Backing up your data is optional. The upgrade process automatically brings your data from
Vantage Report v2.3 to v2.3.1 or from v2.3.1 to v3.0. A backup is only useful if the upgrade fails.
You would only back up your data once (in v2.3, or in v2.3.1 if you are already using v2.3.1).
Full Data Backup
If you want to back up all of your Vantage Report v2.3 or v2.3.1 data, copy the content in the
Vantage Report installation folder (such as C:\ Program Files\ZyXEL\Vantage Report) to another
folder. If the upgrade fails, use the copy to overwrite the content in the Vantage Report
installation folder. Then retry the upgrade.
Partial Data Backup
A full backup can take a long time if you have a lot of data. If you do not need to keep all of the
data, you can do the following to only backup the configuration and device list.
1 Start Vantage Report v2.3 (or v2.3.1) and login.
4
ENGLISH
2 Click System > Data Maintenance > Configuration > Backup to save your configuration to
your computer.
3 Click System > Data Maintenance > Device List > Export to save your list of devices to your
computer.
If the upgrade process fails, you can do a new install of Vantage Report v3.0 (instead of an
upgrade) and manually upload these files to add your data.
1.2.2 Upgrade Vantage Report
Use this procedure to upgrade from Vantage Report v2.3. to v2.3.1 or from v2.3.1 to v3.0.
1 Stop Vantage Report v2.3 (or v2.3.1). Also close MySQL and Tomcat (see section 1.4).
2 Close any other programs on your computer (the installation requires a computer restart).
3 Get the Vantage Report v2.3.1 (or v3.0) package and run the installation program.
4 The installer detects Vantage Report v2.3 (or v2.3.1) and displays a screen like the following.
Select Upgrade Vantage Report 2.3 to 2.3.1 (or 2.3.1 to 3.0) and click Next.
5 Follow the prompts until you finish the installation.
5
ENGLISH
6 Vantage Report automatically runs the next time your computer restarts. You can also start
Vantage Report from the Windows start menu. The login screen displays. You may have to
clear your browser’s cache and refresh the browser to get the 2.3.1 (or 3.0) to appear.
Repeat the upgrade steps to upgrade from Vantage Report v2.3.1 to v3.0. The upgrade requires
a computer restart. See section 3 to login to Vantage Report v3.0 after your computer restarts.
1.3 Uninstall Old Versions of Vantage Report
1 If an old version of Vantage Report is running, stop it.
2 In Windows 2000, click Start > Settings > Control Panel > Add/Remove Programs >
Vantage Report > Change/Remove. Follow the prompts to remove Vantage Report.
In Windows XP, click start > Control Panel > Add/Remove Programs > Vantage Report >
Change/Remove. Follow the prompts to remove Vantage Report.
1.4 Close MySQL and Tomcat
When you install Vantage Report, you also install MySQL and Tomcat. If these applications run
on the Vantage Report server, make sure these applications are closed before you install
Vantage Report. Follow these steps to check whether or not these applications are running and
to stop them.
1 In Windows 2000, click Start > Settings > Control Panel > Administrative Tools >
Services. The Services screen opens.
6
ENGLISH
In Windows XP, click start > Control Panel > Performance and Maintenance > Administrative
Tools > Services. The Services screen opens.
2 If there are no MySQL or Tomcat services running on the Vantage Report server, go to the
next section. Otherwise, right-click on any MySQL or Tomcat service that is running. The
menu that you see above appears.
3 Select Stop in the menu. Repeat steps 2 and 3 if other MySQL or Tomcat services are still
running on the Vantage Report server.
2 Installation
Put the CD into your CD-ROM. The following screen appears.
7
ENGLISH
Click Setup > Vantage Report to start installing Vantage Report. The CD may first extract some
files. Then, the Vantage Report installation wizard appears.
Click Next. Follow the prompts. Before you finish, the following screen appears.
Enter the port number you want Vantage Report to use for web services. Make sure this port
number does not conflict with other services in your network. Click Next when you are ready.
When you finish installing Vantage Report, restart the Vantage Report server.
3 Login
By default, the Vantage Report server starts automatically when you log in to the Vantage Report
server. To access the Vantage Report server,
1 Open a browser window, and go to http://a.b.c.d:xxxxx/vrpt, where
8
ENGLISH
• a.b.c.d is the IP address of the Vantage Report server. If you open the web configurator on the same computer on which you installed Vantage Report, enter
xxxxx is the port number you entered during installation. (See section 2.)
•
For example, http://localhost:8080/vrpt or http://212.100.9.161:9090/vrpt.
The Login screen appears. If it does not appear, see Troubleshooting.
2 In the login screen, enter your user name and password, and click Login.
• Default user name:
• Default password: root
The main screen appears. It is divided into three parts.
root
localhost.
A B
Use the device window (A) to select a device. Right-click to add and remove devices.
Use the function window (B) to select a report.
Use the report window (C) to look at and adjust the selected report for the selected device.
C
4 E-mail Setup
You should have an e-mail account on a SMTP mail server for Vantage Report. You can use an
existing account or create a new one. In either case, you must have the SMTP mail server (IP or
domain name), e-mail address, user name (if required), and password (if required).
9
ENGLISH
4.1 Set Up Administrator E-mail Address
You should set up the e-mail address for the Vantage Report administrator first. This e-mail
address is used to test the SMTP settings in section 4.2. It is also used for system notifications or
if you forget the password for the root account. (If you forget the password, click Forget
Password? in the Login screen.) See the User’s Guide for more detail.
1 Log in to the Vantage Report server. (See section 3.)
2 In the function window, click System > User Management. The User List screen appears.
3 Click root. The Edit User screens appears.
4 Type the e-mail address for the Vantage Report administrator in the E-mail field.
5 Click Apply.
10
ENGLISH
4.2 Set Up SMTP Mail Server
1 In the function window, click System > Server Configuration. The Server Configuration
screen appears.
2 Follow the directions in the table below to fill in the Server Configuration screen.
LABEL DESCRIPTION
SMTP IP Address or
Domain Name
User Name Enter the user name required by the SMTP mail server. If the user
Password Enter the password required by the SMTP mail server. If the password
Sender E-mail Enter the e-mail address you want to be the sender when Vantage
Receiver E-mails Enter the e-mail address you want to be the receiver when Vantage
Enter the IP address or domain name of the SMTP mail server on
which Vantage Report has an account.
name is not required, leave this field blank.
is not required, leave this field blank.
Report sends e-mail. This is the e-mail address from which Vantage
Report e-mail appears to be sent.
Report sends e-mail. This is the e-mail address to which Vantage
Report e-mail appears to be sent.
3 Click Apply. (You must save these settings before you can test them in the next step.)
4 Click Test. Vantage Report sends a test message to the e-mail address you specified in
section 4.1 and the e-mail address in the Receiver E-mails field.
5 Confirm that the specified e-mail account received the message from Vantage Report. If it did
not receive the e-mail, see Troubleshooting.
11
ENGLISH
5 Registration
You only have to register Vantage Report if you want to get the trial version or upgrade to the full
version.
•The basic version provides a variety of statistical and scheduled reports for one device.
•The full version supports more reports, more features, and more devices than the basic version.
•The trial version is a limited-time, free trial of the full version. It does not support as many
devices as the full version, however.
The Vantage Report server must have access to http://www.myZyXEL.com during registration. In
addition, some information may also be required for setup.
If you have a myZyXEL.com account, you need your ...
• myZyXEL.com user name
• myZyXEL.com password
If you want to upgrade to the full version, you need your ...
• license key (iCard in the folder you received when you purchased the full version)
1 Log in to the Vantage Report server. (See section 3.)
2 In the function window, click System > Registration. The Registration screen appears.
3 If you want to get the trial version, click Trial.
If you want to upgrade to the full version, click Upgrade.
12
ENGLISH
In either case, the following screen appears. Some fields do not appear in your screen if you
already have a myZyXEL.com account or if you are getting the trial version.
4 Follow the directions in the table below to fill in this screen.
LABEL DESCRIPTION
License Key Enter the license key on the iCard if you are upgrading to the full
version. The iCard is in the folder you receive when you purchase the
full version.
New myZyXEL.com
account
Existing myZyXEL.com
account
User Name If you do not have a myZyXEL.com account, enter the user name that you
Password If you do not have a myZyXEL.com account, enter the password that you
Confirm Password Retype your password.
Select this if you do not have a myZyXEL.com account. Vantage Report
creates the account for you.
Select this if you already have a myZyXEL.com account.
would like to use for your new myZyXEL.com account. Your user name
can consist of alphanumeric characters and underscores (_) and must be
6 - 20 characters long.
If you already have a myZyXEL.com account, enter the user name for
that account.
would like to use for your new myZyXEL.com account. Your password
can consist of alphanumeric characters and underscores (_) and must be
6 - 20 characters long.
If you already have a myZyXEL.com account, enter the password for that
account.
13
ENGLISH
LABEL DESCRIPTION
E-mail Address Enter the e-mail address where you would like to be notified about your
new myZyXEL.com account.
Country Select the place where you work.
5 Click Upgrade. The updated Registration screen appears. If it does not, see Troubleshooting.
6 Device Setup
Check the release notes for each of your ZyXEL devices to find out if the current firmware
supports Vantage Report. Make sure you check the release notes for the exact version; for
example, check the release notes for v3.64(XV.5), not just v3.64. Some models and some
firmware versions only support some reports. Generally, the following firmware versions support
some or all reports in Vantage Report.
• ZyWALL 2/10W version 3.62 or later
• ZyWALL 5/35/70 version 3.62 or later
• ZyWALL P1 version 3.64 or later
• ZyWALL 1050 version 1.01
• IDP 10 version 2.0 or later
• P-662/P-652 version 3.40 or later
You have to configure each ZyXEL device to send its log entries and traffic statistics to the
Vantage Report server, and you have to add each device to Vantage Report.
6.1 Configure ZyXEL Devices
These steps may vary for different devices. If you already set up devices for previous versions of
Vantage Report, check this section to make sure the device configuration has not changed.
Go to section 6.2 if you need to configure the ZyWALL 1050.
1 Log in to the web configurator for the device, and click Logs > Log Settings. The lower part of
a typical screen is shown below.
14
ENGLISH
Note: Vantage Report uses the log categories that are shown selected in this screen. It is
recommended that you select only these categories.
2 In the Syslog Logging section, select the Active check box.
3 Type the IP address or name of the Vantage Report server in the Syslog Server field.
15
ENGLISH
4 In the Log column, select the categories you want to see in Vantage Report. System
Maintenance, Forward Web Sites, Blocked Web Sites, Attacks, IPSec, IDP, Anti-Virus, and
Anti-Spam are required for various reports in Vantage Report. (Some of these are not
available in every device.) You can only look at log messages for other categories.
5 Activate Log Consolidation to merge logs with identical messages into one log.
6 Click Apply to save your changes.
7 Click LOGS > Reports (or REPORTS > SYSTEM REPORTS in some firmware versions). If the
device does not have this screen, skip steps 7 - 9. The top section of a typical screen is
shown below.
8 In the Setup section, select the Send Raw Traffic Statistics to Syslog Server for Analysis
check box.
9 Click Apply to save your changes.
10If the ZyXEL device provides IDP, go to IDP > Signature (in most ZyXEL devices). Make sure
the device records log entries for the attack types you want to see in Vantage Report.
11If the ZyXEL device provides anti-virus protection, go to Anti-Virus > General (in most ZyXEL
devices). Make sure the device records log entries for viruses the services (in which the
device found the virus) you want to see in Vantage Report.
6.2 Configure the ZyWALL 1050
1 Log in to the web configurator for the device, and click Maintenance > Logs > Log Setting
> Remote Server > Edit
.
16
ENGLISH
Note: Vantage Report uses the log categories that are shown selected in this example. It is
recommended that you select only these categories.
17
ENGLISH
2 Select the Active check box.
3 Type the IP address or name of the Vantage Report server in the Syslog Server field.
4 In the Active Log section, select the categories you want to see in Vantage Report. (Some of
these are not available in every device.) You can only look at log messages for other
categories.
5 Click OK to save your changes.
6 If the ZyXEL device provides IDP, make sure the IDP profile is set to record log entries for the
attack types you want to see in Vantage Report.
6.3 Add ZyXEL Devices to Vantage Report
Use section 6.3.1 if you did a new install of Vantage Report v3.0. If you upgrade from Vantage
Report v2.3.1, your data is brought in automatically and you can skip this section. Section 6.3.2
only applies if the upgrade fails and you have a partial data backup (see section 1.2.1).
6.3.1 Add Devices Manually
You must have the LAN MAC address and model type of the device.
1 Log in to the Vantage Report server. (See section 3.)
2 In the device window, right-click on root. The following menu appears.
3 Select Add Device. The Add Device screen appears.
4 Follow the directions in the table below to fill in the Add Device screen.
LABEL DESCRIPTION
Name Enter the name of the device you want to add to Vantage Report. The name can
consist of alphanumeric characters or underscores (_) and may be 1 - 28 characters
long. This name is used to refer to the device in Vantage Report, and it has to be
unique in Vantage Report. In some cases, the device’s System Name might be
appropriate.
18
ENGLISH
LABEL DESCRIPTION
MAC Enter the LAN MAC address of the device you want to add. You must enter 12
hexadecimal numbers (0 - 9, A - F). Do not use colons (:). This address is usually
located on a label that is on the bottom of the device. If there are two addresses on the
label, the LAN MAC address is usually on the top. For the ZyWALL 1050, use the first
(lowest) LAN MAC address.
Type Select the model type of the device you want to add.
Note Enter any additional notes you want to make here. You can enter up to 50 printable
ASCII characters. You can also leave this field blank.
5 Click the Add button. The device should now appear in the device window. You can select it
(for example, if you want to generate a statistical report for it) by clicking on it once. See the
User’s Guide for more information.
6.3.2 Import a Device List
1 Log in to the Vantage Report server. (See section 3.)
2 In the function window, click System > Data Maintenance > Device List Import & Export. The
Device List Export / Import screen appears.
3 Enter the name and location of the file you saved in section 1.2, or click Browse... to look for
it.
4 Click Import. The following message appears.
5 Click OK to close the message.
6 In the device window, click the Refresh icon in the upper right corner. The devices you had
in Vantage Report v2.3 should appear.
19
ENGLISH
Follow the directions in section 6.3.1 to add additional devices manually.
Troubleshooting
See the User’s Guide for additional troubleshooting.
PROBLEM CORRECTIVE ACTION
The web configurator is not
connecting to the Vantage
Report server.
The Vantage Report server
does not start up
automatically.
The web configurator
returns to the Login screen
when I try to do something.
Make sure you are using the correct URL. Enter
a.b.c.d:xxxxx
a.b.c.d is the IP address of the Vantage Report server. If you
•
open the web configurator on the same computer on which you
installed Vantage Report, enter
xxxxx is the port number you entered during installation. (See
•
section 2.)
For example, you might enter http://localhost:8080/vrpt or http://
212.100.9.161:9090/vrpt.
Make sure packets on TCP port 3316, UDP port 514, and the port
number you specified during installation are forwarded to the Vantage
Report server, especially if the Vantage Report server runs behind a
NAT or firewall.
Make sure the Vantage Report server is running.
• The Vantage Report server runs as a service. Follow the directions
in section 1.4 to check it.
• Make sure the following system variables are defined.
PATH=C:\WINNT\system32;C:\WINNT;C:\WINNT\System32\Wbem
The drive letter and names of folders depend on your Vantage
Report server. To check these variables in Windows 2000, click
Start > Settings > Control Panel > System > Advanced > Environment Variables. In Windows XP, click start > Control Panel >
System > Advanced > Environment Variables. Make sure the
variables are in the System Variables box.
• The Vantage Report server does not start automatically if there is a
port conflict on the port number you specified during installation.
Click Start > Run, and enter
port conflict.
If the problem continues, contact your local vendor.
For security reasons, the web configurator times out in fifteen minutes.
Log in again.
/vrpt, where
localhost.
netstat -a to find out if there is a
http://
20
ENGLISH
PROBLEM CORRECTIVE ACTION
Vantage Report did not
send the test e-mail to the
administrator’s e-mail
account.
I cannot register (get the
trial version or upgrade to
the full version).
Make sure the SMTP settings and e-mail account are correct. If your
SMTP mail server requires authentication, make sure you entered the
user name and password correctly. See section 4.
Make sure the Vantage Report server can connect to the SMTP mail
server.
If the problem continues, contact your local vendor.
Make sure you have the right license key, and make sure you enter the
requested information correctly. See section 5.
Make sure the Vantage Report server can connect to http://
www.myzyxel.com. The Vantage Report server interacts with this site
during registration.
If the problem continues, contact your local vendor.
Viewing Your Product’s Certifications
Go to www.zyxel.com, select your product from the drop-down list box on the ZyXEL home page,
and select the certification you wish to view.
21
ENGLISH
22
DEUTSCH
Vantage Report
Vantage Report sammelt Log-Einträge und Datenverkehrsstatistiken von ZyXEL-Geräten und
generiert dann grafische und tabellarische Berichte über Netzwerkleistung und Ereignisse.
C
A
Installieren Sie Vantage Report auf dem Vantage Report-Server (B). Konfigurieren Sie ihn dann
mit dem Web-Konfigurator (A). (Der Web-Konfigurator kann auf einem Remote-Computer oder
auf dem Vantage Report-Server laufen.) Konfigurieren Sie abschließend die ZyXEL-Geräte (C)
so, dass sie ihre Log-Einträge und Datenverkehrsstatistiken an den Vantage Report-Server
senden. Der Vantage Report-Server sammelt diese Daten und erzeugt dann statistische Berichte
über das Netzwerk. Diese Berichte können dann von jedem jederzeit im Web-Konfigurator
eingesehen oder als E-Mail versendet werden.
B
Übersicht
1 Vorbereitung - Stellen Sie sicher, dass der Vantage Report-Server die Mindestanforderungen
erfüllt und bereiten Sie ihn für die Installation vor.
2 Installation - Installieren Sie Vantage Report auf dem Vantage Report-Server.
3 Anmeldung - Greifen Sie mit dem Web-Konfigurator auf den Vantage Report-Server zu.
4 E-Mail-Setup - Richten Sie in Vantage Report die E-Mail-Adresse des Administrators und die
SMTP-Mailservereinstellungen ein und prüfen Sie die SMTP-Einstellungen.
5 Registrierung - Wenn Sie Vantage Report installieren, erhalten Sie die Grundversion. Sie
müssen Vantage Report nur dann registrieren, wenn Sie die Testversion oder ein Upgrade für
die Vollversion erhalten möchten. (Weitere Informationen über die Versionen finden Sie in
Abschnitt 5.)
6 Geräte-Setup - Richten Sie die ZyXEL-Geräte ein und fügen Sie sie zum Vantage Report-
Server hinzu.
23
DEUTSCH
1 Vorbereitung
Prüfen Sie folgende Punkte, bevor Sie Vantage Report installieren.
1.1 Prüfen der Mindestanforderungen
Wenn Ihr Vantage Report-Server nicht die Mindestanforderungen erfüllt, muss er aufgerüstet
werden, oder Sie müssen einen anderen Server verwenden, der diese Anforderungen erfüllt.
Anzahl registrierter Geräte CPU Freier Festplattenspeicher (GB)
<5 Pentium IV 2.6 GHz 10
<50 Pentium IV 2.6 GHz Doppelte Anzahl Geräte
50-100 Pentium IV 3.2 GHz oder
schneller
Betriebssystem Windows XP Professional, Windows 2000/2003 Server
Browser
(auf Server oder
anderem
Computer)
Weitere
Anforderungen für
unterstützte Dienste
Internet Explorer 6.0 (Service Pack 1) oder neuere Version auf Windows
Mozilla 1.7.12 oder neuere Version auf Windows
Firefox 1.07 oder neuere Version auf Windows
Auflösung 1024 x 768
SMTP-Daemon
TCP-Port 3316 und UDP-Port 514
Doppelte Anzahl Geräte
1.2 Aktualisieren von Vantage Report v2.3 oder v2.3.1
Lesen Sie diesen Abschnitt für die Aktualisierung von Vantage Report v2.3 (2.3.05.61.00) auf
v2.3.1 (2.3.00.61.01). Angaben über die derzeit verwendete Version finden Sie bei System
(System) > About (Über). Verwenden Sie es noch einmal für die Aktualisierung von v2.3.1 auf
v3.0. Wenn Sie bereits mit v2.3.1 arbeiten, können Sie dirket eine Aktualisierung auf v3.0
vornehmen.
1.2.1 Datensicherung
Das Sichern von Daten ist optional. Bei der Aktualisierung werden Ihre Daten automatisch von
Vantage Report v2.3 nach v2.3.1 oder von v2.3.1 nach v3.0 übertragen. Eine Datensicherung
wird nur benötigt, wenn die Aktualisierung fehlschlägt. Die Daten werden nur einmal gesichert (in
v2.3 bzw. in v2.3.1 , wenn Sie bereits v2.3.1 verwenden).
Vollständige Datensicherung
24
DEUTSCH
Wenn Sie alle Daten aus Vantage Report v2.3 oder v2.3.1 sichern möchten, kopieren Sie den
Inhalt des Vantage Report-Installationsordners (z. B. C:\Programme\ZyXEL\Vantage Report) in
einen anderen Ordner. Sollte die Aktualisierung fehlschlagen, können Sie den Vantage ReportInstallationsordner mit der Kopie überschreiben. Führen Sie dann erneut eine Aktualisierung
durch.
Teildatensicherung
Wenn Sie viele Daten haben, kann eine vollständige Datensicherung lange dauern. Falls Sie
nicht alle Daten benötigen, können Sie auf folgende Weise nur die Konfiguration und die
Geräteliste sichern.
1 Starten Sie Vantage Report v2.3 (oder v2.3.1), und melden Sie sich an.
2 Klicken Sie auf System (System) > Data Maintenance (Datenwartung) > Configuration
(Konfiguration)?> Backup (Datensicherun), um die Konfiguration im Computer zu speichern.
3 Klicken Sie auf System (System)> Data Maintenance (Datenwartung) > Device List
(Geräteliste)> Export (Exportieren), um Ihre Geräteliste im Computer zu speichern.
Wenn die Aktualisierung fehlschlägt, können Sie Sie Vantage Report v3.0 erneut installieren
(anstelle einer Aktualisierung) und dann diese Dateien manuell zu Ihren Daten hinzufügen.
1.2.2 Aktualisieren von Vantage Report
Mit dieser Funktion können Sie Vantage Report von v2.3. auf v2.3.1 oder von v2.3.1 auf v3.0
aktualisieren.
1 Stoppen Sie Vantage Report v2.3 (oder v2.3.1). Schließen Sie auch MySQL und Tomcat
(siehe Abschnitt 1.4).
2 Schließen Sie alle Programme auf Ihrem Computer (die Installation erfordert einen Neustart
des Computers).
3 Starten Sie das Installationsprogramm des Vantage Report-Pakets v2.3.1 (oder v3.0).
25
DEUTSCH
4 Das Installationsprogramm erkennt Vantage Report v2.3 (oder v2.3.1) und zeigt ein Fenster
wie das folgende an. Wählen Sie Upgrade Vantage Report 2.3 to 2.3.1(Vantage Report 2.3
auf 2.3.1 aktualisieren) (oder 2.3.1 to 3.0), und klicken Sie auf Next (Weiter).
5 Führen Sie bis zum Ende der Installation alle Befehle auf dem Bildschirm aus.
6 Beim nächsten Start des Computers wird Vantage Report automatisch gestartet. Sie können
Vantage Report auch aus dem Windows-Startmenü starten. Das Anmeldefenster wird
angezeigt. Möglicherweise müssen Sie den Cache Ihres Browsers löschen und den Browser
aktualisieren, damit Vantage Report 2.3.1 (oder 3.0) angezeigt wird.
Wiederholen Sie die Schritte, um von Vantage Report v2.3.1 auf v3.0 zu aktualisieren. Die
Aktualisierung erfordert einen Neustart des Computers. Wie Sie sich bei Vantage Report v3.0
nach dem Neustart des Computers anmelden, erfahren Sie in Abschnitt 3.
1.3 Deinstallieren älterer Versionen von Vantage Report
1 Stoppen Sie die ältere Version von Vantage Report.
2 Klicken Sie bei Windows 2000 auf Start > Einstellungen > Systemsteuerung > Programme
hinzufügen/entfernen > Vantage Report > Ändern/Entfernen. Führen Sie die
Anweisungen aus, um Vantage Report zu entfernen.
26
DEUTSCH
Klicken Sie bei Windows XP auf Start > Systemsteuerung > Programme hinzufügen/
entfernen > Vantage Report > Ändern/Entfernen. Führen Sie die Anweisungen aus, um
Vantage Report zu entfernen.
1.4 Schließen von MySQL und Tomcat
Wenn Sie Vantage Report installieren, installieren Sie gleichzeitig MySQL und Tomcat. Wenn
diese Anwendungen auf dem Vantage Report-laufen, müssen diese vor der Installation von
Vantage Report geschlossen werden. Führen Sie die folgenden Schritte aus, um zu prüfen, ob
diese Programme laufen und um sie zu stoppen.
1 Klicken Sie bei Windows 2000 auf Start > Einstellungen > Systemsteuerung > Verwaltung
> Dienste. Das Fenster Dienste wird aufgerufen.
Klicken Sie bei Windows XP auf Start > Systemsteuerung > Leistung und Wartung >
Verwaltung > Dienste.Das Fenster Dienste wird aufgerufen.
2 Wenn auf dem Vantage Report-Server keine MySQL- oder Tomcat-Dienste laufen, gehen Sie
weiter zum nächsten Abschnitt. Anderenfalls klicken Sie auf alle MySQL- oder TomcatDienste, die gerade laufen. Das oben abgebildete Menü erscheint.
3 Wählen Sie in diesem Menü die Option Stop. Wiederholen Sie die Schritte 2 und 3 für alle
weiteren MySQL- und Tomcat-Dienste, die noch auf dem Vantage Report-Server laufen.
27
DEUTSCH
2 Installieren
Legen Sie die CD in das CD-ROM-Laufwerk. Das folgende Fenster erscheint.
Klicken Sie auf Setup > Vantage Report, um die Installation von Vantage Report zu starten.
Zunächst werden einige Dateien der CD extrahiert. Dann erscheint der Installationsassistent von
Vantage Report.
28
DEUTSCH
Klicken Sie auf Next. Führen Sie die Anweisungen aus. Bevor die Installation abgeschlossen ist,
erscheint das folgende Fenster.
Geben Sie die Port-Nummer an, die Vantage Report für Webdienste verwenden soll. Stellen Sie
sicher, dass diese Port-Nummer nicht mit anderen Diensten im Netzwerk zusammenfällt. Klicken
Sie auf Next, wenn Sie fertig sind.
Wenn Sie die Installation von Vantage Report abgeschlossen haben, muss der Vantage ReportServer neu gestartet werden.
3 Anmeldung
Standardmäßig startet der Vantage Report-Server automatisch, wenn Sie sich beim Vantage
Report-Server anmelden. So greifen Sie auf den Vantage Report-Server zu:
1 Öffnen Sie ein Browserfenster und rufen Sie die Seite http://a.b.c.d:xxxxx/vrpt auf,
wobei
• a.b.c.d die IP-Adresse des Vantage Report-Servers ist. Wenn Sie auf demselben Computer, auf dem Sie Vantage Report installiert haben, den Web-Konfigurator öffnen, geben
Sie localhost ein.
xxxx ist die Port-Nummer, die Sie während der Installation eingegeben haben. (Siehe
•
Abschnitt 2.)
Zum Beispiel http://localhost:8080/vrpt oder http://212.100.9.161:9090/vrpt.
29
DEUTSCH
Das Fenster Login erscheint. Sollte es nicht erscheinen, lesen Sie nach unter
Problembeseitigung.
2 Geben Sie im Fenster Login Ihren Benutzernamen und Ihr Kennwort ein und klicken Sie auf
Login.
• Standardbenutzername:
• Standardkennwort: root
Das Hauptfenster erscheint. Es ist in drei Bereiche unterteilt.
root
A
Im Gerätefenster (A) wird ein Gerät ausgewählt. Klicken Sie mit der rechten Maustaste darauf,
um Geräte hinzuzufügen oder zu entfernen.
Im Funktionsfenster (B) wird ein Bericht ausgewählt.
Im Berichtfenster (C) können Sie sich die ausgewählten Berichte für das ausgewählte Gerät
ansehen und anpassen.
B
C
4 E-Mail-Setup
Sie benötigen für Vantage Report ein E-Mail-Konto auf einem SMTP-Mailserver. Sie können ein
bestehendes Konto verwenden oder ein neues erstellen. In jedem Fall benötigen Sie den SMTPMailserver (IP oder Domain-Name), E-Mail-Adresse, Benutzername (wenn erforderlich) und
Kennwort (wenn erforderlich).
30
Loading...