Vantage Centralized Network Management 2.0 (CNM) is a browser-based, management
solution that allows you to easily configure, manage and monitor ZyXEL devices from any
location. Vantage Centralized Network Management 2.0 will be referred to as “Vantage
CNM” or simply “Vantage” in this document.
This Quick Start Guide shows you to install and configure Vantage CNM on Redhat Linux
2.0.00.61.00 for information on how to install and configure Vantage CNM on Windows XP
professional.
2 Vantage Requirements
2.1 Vantage Server Requirements
CPU Intel Pentium 4, 2.6 GHz or faster
RAM 1GB or more
Hard Drive 80GB
Operating System Linux Redhat 9.0
2.2 Vantage Client Requirements
CPU Intel Pentium III, 450MHz or faster
RAM 256MB or more
Web Browser
"Internet Explorer 6.0 or later
4
Vantage CNM 2.0
2.3 ZyXEL device requirements
Firmware This Vantage release can manage up to 300 ZyXEL devices.
The ZyXEL device must have Vantage CNM-enabled firmware.
At the time of writing, devices supported were ZyWALL 2,
ZyWALL 2X, ZyWALL 5, ZyWALL 10W, ZyWALL 35, ZyWALL
70 and Prestige 652HW-31/33/37. For more details, see the
Vantage software release notes.
Please read the device release note carefully if you have to
upload new device firmware.
How to activate Vantage on
a device using commands.
Go to command mode (SMT menu 24.8 of most ZyXEL devices)
and issue the following two commands:
1. Enable Vantage on the device by entering “CNM active 1”.
2. If the Vantage server is on the same subnet as the ZyXEL
device enter "CNM ManagerIp x.x.x.x" on the ZyXEL device
where ”x.x.x.x” is the IP address (private or public) the Vantage
server.
If the Vantage server is on a different subnet to the ZyXEL
device, enter "CNM ManagerIp x.x.x.x" on the ZyXEL device
where ”x.x.x.x” is the public IP address of the Vantage server.
If the Vantage CNM server is on a different subnet to the
ZyWALL and is behind a NAT router, enter the WAN IP address
of the NAT router here and configure the NAT router to forward
UDP port 1864 traffic to the Vantage CNM server.
If the ZyXEL device is behind a firewall, you may have to create
a rule on the firewall to allow UDP port 1864 traffic through to
the Vantage CNM server (most (new) ZyXEL firewalls
automatically allow this).
5
Vantage CNM 2.0
Encrypt traffic between
Vantage and the device by
doing the following:
How to activate Vantage on
a device and encrypt traffic
using the web configurator.1
The ZyXEL device will not
be able to register with
Vantage if:
1. Go to CI (Command Interface) mode (SMT 24.8 for devices
with SMT menus)
2. Type 'CNM encrymode X' where X = 0 is no encryption, X =1
is DES encryption, X = 2 is 3DES encryption. The ZyXEL device
must use the same encryption method as Vantage.
3.To set the encryption key (if X = 1 or 2) on the ZyXEL device,
type 'CNM encrykey xxxxxxxxx' where ‘xxxxxxxxx’ is the
alphanumeric encryption key (“0” to “9”, “a” to “z” or “A” to “Z”) in
the Vantage server. Type an eight-character alphanumeric (“0”
to “9”, “a” to “z” or "A" to "Z") for DES encryption and a 24character alphanumeric for 3DES encryption. The ZyXEL
device must use the same encryption key as Vantage
Log into the device web configurator, click Remote Management from the navigation panel and then click the CNM
tab. Select Enable, enter the Vantage CNM Server (IP)
Address and select an Encryption Algorithm and Encryption
Key if desired.
o The Vantage CNM server is down.
o The Vantage CNM server IP address is incorrect.
o The Vantage CNM server is behind a NAT router or firewall
that does not forward packets through to the Vantage CNM
server.
o The encryption algorithms and/or encryption keys do not
match between the ZyXEL device and Vantage.
3 Vantage Installation Procedure
Use the Vantage installation wizard to install Vantage CNM 2.0 server software.
In each wizard screen, click Next to proceed to the next screen in the
wizard, click Back to return to the previous screen or click Cancel to
abort the installation and exit the wizard.
1
Not available at the time of writing
6
Vantage CNM 2.0
You should uninstall any previous versions of Vantage before
beginning.
3.1 Extracting Vantage
1. Insert the Vantage CD into the CD-ROM or download the Vantage software and save it to
a folder, for example, /usr/Vantage-2.0.
2. Navigate to this folder using the “cd” command and type the following to extract the
Vantage files.
./Vantage_CNM_2_0.bin
(You may need to make the file executable first using chmod +x Vantage_CNM_2_0.bin)
Figure 1 Extracting Vantage
Alternatively, double-click the Vantage_CNM_2_0.bin icon.
Figure 2 Extracting Vantage Icon
3. Vantage must be able to ping the hostname of your computer; otherwise you see the next
screen.
7
Vantage CNM 2.0
Figure 3 Vantage Pings Hostname
4. The Vantage CNM logo appears briefly when extraction begins.
8
3.2 Installation Wizard
Vantage CNM 2.0
Figure 4 Vantage CNM Logo
5. The first wizard screen appears after successful extraction. You should uninstall any
existing MySQL servers and remove the /etc/my.cnf directory. You should prepare all
FTP, SMTP and syslog server IP addresses and login names/passwords (for syslog on
Windows, you need a Telnet login name and password, for syslog on Linux, you need an
SSH login name and password. You can configure these servers during the wizard
installation or after you install Vantage in the System > Preferences > Servers screen.
9
Vantage CNM 2.0
Figure 5 Wizard 1: Before You Begin
If a MySQL server is detected, you see the following screen.
Figure 6 Existing MySQL Server Detected
10
Vantage CNM 2.0
6. Select a folder where you would like to install Vantage. Spaces in the folder name or path
are not allowed.
Figure 3 Choose Installation Folder
You will see an error screen as shown next if your installation folder or path has a space.
Figure 7 – Path Space Error
11
Vantage CNM 2.0
7. The next screen asks you where you want to create a Vantage link or shortcut. After you
install Vantage you will see a Launch Vantage icon in this folder.
Figure 8 Select Folder
8. You next configure a syslog server. syslog is a logging system that is used by most
versions of UNIX. If Vantage finds an existing syslog server on your computer, you see
the next screen asking you if this is the syslog server you wish to use. If not, choose No.
See the User’s Guide Appendices for examples of setting up syslog
and FTP servers.
12
Loading...
+ 28 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.