Zyxel OMNI 56K Installation Guide

Omni 56K USB Modem
Quick Start Guide

Contents

1. MAKING CONNECTION VIA USB .....................2
HARDWARE INSTALLATION 2 SOFTWARE INSTALLATION FOR WINDOWS® OS 3 INSTALL USB DRIVER AND PPP SETUP FOR MAC OS 6
2. BITWARE INSTALLAT ION................................ 12
INSTALLING BITWARE 12
ZyXEL
T
OTAL INTERNET ACCESS SOLUTION
ZyXEL Omni 56K USB Modem Quick Start Guide
2
1. Making Connection via USB

Hardware Installation

Ê Connect your modem to your analog phone or fax. Ë Use the phone cord included to connect to the
phone jack on the wall.
Ì Plug one end of your USB cable to your modem
and the other end to an available USB port on your PC.
ZyXEL Omni 56K USB Modem Quick Start Guide
3
NOTE:

Software Installation for Windows® OS

Follow the steps below to install your USB driver.
Step 1. Be sure your PC is
already turned on before connecting the USB cable from your modem to your PC. The plug and play function of Windows® 98 detects your new device and shows an installation wizard as shown on the left. Click Next to continue.
If your Windows® system does not detect your new device automatically, you may unplug the USB cable and reboot your Windows® system, then try Step 1 above again.
ZyXEL Omni 56K USB Modem Quick Start Guide
4
Step 2. Click Next to
Step 3. Insert the CD-
Step 4. The installation
accept the default selection.
ROM disc included into your CD-ROM drive, select CD-ROM drive and then click Next.
wizard has found the location of your USB driver. Click Next to continue and Windows® will copy the driver files into your system as well as build the driver information database.
ZyXEL Omni 56K USB Modem Quick Start Guide
5
Step 5. The ZyXEL USB
modem has been successfully installed on your computer. Click Finish, then follow the wizard to complete the driver installation.
For more information on how to upgrade your modem's firmware, please refer to the User's Guide
for ZyXEL Omni 56K USB Modem.
ZyXEL Omni 56K USB Modem Quick Start Guide
6

Install USB Driver and PPP Setup for Mac OS

This section provides step by step procedures to install the USB device driver and setup PPP on the Mac OS.

Install USB Driver for Mac OS

Omni56K_USB_Installer, a MindVision VISE Installer, is used to install ZyXEL Omni 56K USB device driver on your Macintosh. Perform the following procedure to install the USB device driver on your Macintosh.
Step 1. Be sure your Mac is turned on. Step 2. Insert the CD-ROM disc attached with your
modem device into your CD-ROM drive. You will see the following icon:
ZyXEL Omni 56K USB Modem Quick Start Guide
7
Step 3. Plug the USB connector of your Omni 56K
USB into any one of your devices with a USB port, such as your computer, display monitor, or keyboard, etc.
Step 4. Double click on the
Omni56K_USB_Installer icon. Then, click Continue.
Step 5. Click on the Install button. The ZyXEL
USB device driver will be installed in the
extension folder of the system folder.
ZyXEL Omni 56K USB Modem Quick Start Guide
8
Step 6. You are required to restart your computer to
complete the installation process by clicking on Continue.
Step 7. Click on Restart to reboot your
Macintosh.
You have finished the USB device driver installation for your Mac OS. The following section shows you how to set up a PPP connection for Internet access.
ZyXEL Omni 56K USB Modem Quick Start Guide
9

OT/PPP Setup for Mac OS

Before using OT/PPP, you must use the Control Panels to set up modem, TCP/IP and Remote
Access (or PPP).
Setup the Modem Control Panel
Step 1. Choose Control Panels from the
Apple Menu and open the Modem Control Panel. You will see a window as shown:
Step 2. Choose the port to the ZyXEL Omni 56K
USB from the Connect via pop-up
menu.
Step 3. Choose ZyXEL Omni 56K USB from the
Modem pop-up menu.
Step 4. Save and close.
ZyXEL Omni 56K USB Modem Quick Start Guide
10

TCP/IP Setup for PPP

Step 1. Choose Control Panels from the
Apple Menu and open the TCP/IP control panel. You will see a window as shown:
Step 2. Choose PPP from the Connect via pop-
up menu.
Step 3. Choose your configuration method from the
Configure pop-up menu. For example, Using PPP Server.
Step 4. The most common selection is Using PPP
Server that causes OT/PPP to request IP
address from the server when it connects.
Step 5. Enter Name server addresses. Step 6. Save and close.
ZyXEL Omni 56K USB Modem Quick Start Guide
11

Remote Access Setup (or PPP)

Step 1. Choose Control Panels from Apple
Menu and open the Remote Access (or
PPP) control panel. A window appears:
Step 2. Click Setup to show this panel’s screen. Step 3. Click on Guest or Registered User. Step 4. Enter your PPP user Name and Password
in the text boxes.
Step 5. Enter your ISP's telephone number in the
Number text box.
Click Connect. This will start a dial up and make an OT/PPP connection.
ZyXEL Omni 56K USB Modem Quick Start Guide
12
2. Bitware Installation
The Bitware application is contained in the CD-ROM disc that came with your modem package. To install Bitware, insert the CD-ROM disc into your CD­ROM drive. Then, proceed with the following steps.

Installing Bitware

Step 1. Use Windows® to select your CD-ROM
drive, then double-click on the Msetup.exe icon/filename as shown.
ZyXEL Omni 56K USB Modem Quick Start Guide
13
The following screen appears:
Step 2. Choose the Bitware program from the
Product list-box, and select your
Windows® system and language on the
right side, then click on Install. Follow
the wizard to complete the installation process.
Loading...