Zte Mobley User Manual

User Guide

Mobile Hotspot

i

Welcome to AT&T

Thank you for purchasing the ZTE Mobley. To get the most from your
new device, check out our videos and interactive tutorials at
att.com/Tutorials.

Copyright © 2015 ZTE CORPORATION. All rights reserved. ZTE,
Mobley, and the ZTE logos are trademarks of the ZTE Corporation.

No part of this publication may be excerpted, reproduced, translated
or utilized in any form or by any means, electronic or mechanical,
including photocopying and microfilm, without the prior written
permission of ZTE Corporation.

The manual is published by ZTE Corporation. We reserve the right to
make modifications on print errors or update specifications without
prior notice.

Version No. : V1.0
Edition Time: August 2015

ii iii

Contents

Get Started ...............................................................1

Know Your Device ..................................................... 1

Install Your Mobile Hotspot ...........................................3

Status LED Indicator ..................................................3

Connect to the Internet ...............................................4

Manage Your Mobile Hotspot and Settings. . . . . . . . . . . . . . . . . . . . . . . . . . .5

Connect Devices to Your Mobile Hotspot’s Wi-Fi® ..................5

Use Your Mobile Hotspot ...............................................6

Lite AT&T Wi-Fi Manager Home Page .................................6

Full AT&T Wi-Fi Manager Home Page .................................7

Security Credentials ...................................................8

Manage Wi-Fi ..........................................................9

Messages .............................................................14

Security ...............................................................15

Configure Data Network Options ................................... 22

View Details .......................................................... 24

Replace the micro-SIM Card ........................................ 26

Reset the Mobile Hotspot ........................................... 27

iv 1

Advanced Settings ....................................................28

Manage Wi-Fi ........................................................28

Change Advanced Settings .........................................29

Troubleshooting ....................................................... 34

Problems and Suggested Solutions ................................34

Compatible Vehicles ................................................36

Working Voltage ..................................................... 37

Working State and Transition .......................................38

Specifications ........................................................39

Regulatory and Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

To the Owner .......................................................40

Using Your Device ..................................................40

Radio Frequency (RF) Energy ..................................... 41

FCC Compliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Warranty ..............................................................44

Consumer Limited Warranty ......................................44

Get Started

This chapter provides an overview of the features of your ZTE Mobley
Mobile Hotspot and instructions on how to set it up and connect to
the Internet.

Know Your Device

Your mobile hotspot enables you to create a Wi-Fi network in your
vehicle. You can use that Wi-Fi network to connect your smartphone
and other Wi-Fi-capable devices to your network provider’s mobile
broadband network and connect to the Internet.

OBD II interface

SIM card cover

LED 1 LED 2

Reset key

2 3

Additional features include:

• OBD II Interface — Connect with the On-Board Diagnostics

(OBD II) connector port on your vehicle to power on your mobile
hotspot. The OBD II connector port is usually located on or under
the dash, on the driver’s side. Other possible locations are the
center console area or inside the glove compartment.

• Reset Key — Restore the device to the factory default

configurations.

• Guest Wi-Fi – Set up a guest Wi-Fi network for temporary users, and

use the main network for trusted devices.

Install Your Mobile Hotspot

Make sure your vehicle is parked outside in a safe location and the

engine is turned off.

Insert your mobile hotspot into the OBD II connector port (or

into the extension cable if it is required). Ensure that your mobile
hotspot is inserted in the correct direction.

Note: Insert the mobile hotspot carefully to avoid damaging it.

Status LED Indicator

The LED indicates the device’s connection status:

LED 1

(Power)

Off Sleep mode (Wi-Fi off)

Green solid Power on

Red blinking Factory reset

Red solid SIM locked

LED 2

(Signal)

Off No network service available

Red solid FOTA updating

Green solid

Connected to mobile network,
Wi-Fi network available

Red blinking FOTA update failure

Green blinking FOTA update success

4 5

Connect to the Internet

Start your mobile’s engine and let

it run for at least 30 seconds. Once
powered up, your mobile hotspot
automatically searches for and
connects to your network provider’s
mobile broadband network.

Connect your smartphone or

other Wi-Fi-enabled devices to
your network.

a) Use your normal Wi-Fi application

on the device to search for the
available wireless network.

b) Select the Wi-Fi network name.

c) Input the Wi-Fi network password

as it appears on the label on your
mobile hotspot.

Launch your browser to surf

the Internet.

Note: Once the vehicle’s engine has been off for half an hour, the
ZTE Mobley Mobile Hotspot will disconnect and enter Sleep mode.

Manage Your Mobile Hotspot and Settings

You can use the lite or full AT&T Wi-Fi Manager home page to
manage your mobile hotspot and change settings. In both cases,
log in as Administrator to make changes. The web address is
http://attwifimanager and the default Administrator login
is attadmin.

• To personalize the mobile hotspot and change basic settings, use
a smartphone to connect to the mobile hotspot and then use a
browser to display the lite AT&T Wi-Fi Manager home page.

• For advanced settings, use a Wi-Fi-enabled device such as a
laptop to connect to the mobile hotspot and then use a browser
to display the full AT&T Wi-Fi Manager home page.

Connect Devices to Your Mobile Hotspot’s Wi-Fi

You can connect up to five (5) wireless devices, such as smartphones,
laptops, tablets, digital cameras, printers, gaming consoles, and digital
picture frames, to your mobile hotspot’s Wi-Fi network(s). (See Set
Maximum Number of Connected Devices on page 11 for instructions
on setting connections for the Main Wi-Fi and Guest Wi-Fi networks.)

Connect a wireless device to your Wi-Fi network by typing the Wi-Fi
password.

Connect a Wireless Device Manually

To connect a wireless device to your mobile hotspot’s Wi-Fi network,
see Connect to the Internet on page 4.

6 7

Use Your Mobile Hotspot

This chapter describes the main features of the web interfaces
for managing your mobile hotspot. You must be logged in as
Administrator to change advanced settings and view detailed
information.

• Home page URL — http://attwifimanager

• Default Administrator login — attadmin

Lite AT&T Wi-Fi Manager Home Page

To log in as Administrator:

On the lite AT&T Wi-Fi Manager

home page, enter attadmin
in the Login field.

Tap Login.

Full AT&T Wi-Fi Manager Home Page

To log in as Administrator:

On the full AT&T Wi-Fi Manager home page, enter attadmin in the

Login field.

Click Login.

8 9

Security Credentials

The mobile hotspot uses three passwords:

• Wi-Fi password — Used to authenticate wireless devices to your

mobile hotspot network. It is unique to your mobile hotspot and can
be found printed on a label on the mobile hotspot. If you want to
change the Wi-Fi password, see Change Wi-Fi Network Names and
Passwords on page 15.

• Guest Wi-Fi password — When enabled, temporary users can

use this password to access the Guest Wi-Fi network. If you want
to change the Guest Wi-Fi password, see Change Wi-Fi Network
Names and Passwords on page 15.

• Admin login — Used to log in to the AT&T Wi-Fi Manager home

page as Administrator. You must be logged in as Administrator
to use certain features and to make changes to your mobile
hotspot settings. The default Administrator login is attadmin. The
Administrator login can be changed to 4 - 32 characters.

You can change these passwords on the lite or full AT&T Wi-Fi
Manager home page (http://attwifimanager).

Manage Wi-Fi

View Connected Devices

You can view a list of devices connected to your mobile hotspot on
the lite or full AT&T Wi-Fi Manager home page.

On the lite AT&T Wi-Fi Manager home page:

Log in as Administrator.
Tap Wi-Fi Settings.
A list of devices connected to the Main Wi-Fi and Guest Wi-Fi

networks appears in the Connected Devices section.

10 11

On the full AT&T Wi-Fi Manager home page:

Log in as Administrator.
Tap Connected Devices on the navigation menu on the left side.

A list of devices connected to the Main Wi-Fi and Guest Wi-Fi
networks appears on the screen. You can view the IP and MAC
addresses of the devices.

Set Maximum Number of Connected Devices

You can connect up to five (5) wireless devices to your mobile
hotspot. These connections are shared between the Wi-Fi’s Main and
Guest Wi-Fi networks. You can customize the distribution of devices
from the full AT&T Wi-Fi Manager home page.

On the full AT&T Wi-Fi Manager home page:

Log in as Administrator.
Click Home on the navigation menu on the left side.
In the Main and Guest Wi-Fi Max Devices section, select next

to Main Wi-Fi or Guest Wi-Fi to adjust the number of connections
available.

Click Apply.

Block/Unblock Devices

Whenever you block or unblock devices, the mobile hotspot resets to
activate the new settings. Any devices connected to the hotspot will
be disconnected.