No part of this publication may be excerpted, reproduced, translated or utilized in any form or by
any means, electronic or mechanical, including photocopying and microfilm, without the prior
written permission of ZTE Corporation.
ZTE Corporation operates a policy of continuous development. ZTE Corporation reserves the right
to make changes and improvements to any of the produ ct s described in this documen t without prior
notice.
Limitation of Liability
ZTE shall not be liable for any loss of profits or indirect, special, incidental or consequential
damages resulting from o r arising out of or in connection with using this product, wh ether or
not ZTE had been advised, knew or should have known the possibility of such damages.
The user should refer to the enclos ed warran ty card for ful l warran ty and serv ice informa tion.
5 Menu Listing........................................................................................................83
4
RF Safety Information
The handset has an internal antenna located under the bottom of the keypad. For optimum
performance with minimum power consumption do not cover the antenna area with your
hand. Hold the handset between thumb and finger on the main hinge section. Covering the
antenna affects call quality, may cause the handset to operate at hi gher power level than
needed, and may shorten talk and idle times.
Radio Frequency Energy
Your handset is a low-power radio transmitter and receiver. When switched on it
intermittently transmits radio frequency (RF) energy (radio waves). The transmit power level
is optimized for the best performance and automatically reduces when there is good quality
reception. Maximum power is only used at the edge of network coverage so under most
circumstances the power output is very low. Under poor network conditions the phone will
transmit at a higher power, may get hot and will have a significantly shorter battery life.
Declaration of Conformity
We declare under our sole responsib ility that the product(s) detailed in this manual, and in
combination with our accessories, conform with the essential requirements of The Radio
Communications Standard (Electro-magnetic Radiation Human Exposure) 2003 and the
Australian Communications and Media Authority Section 376 of the Telecommunications Act
1997.
5
General Safety Information
The handset contains delicate electronic circuitry, magnets and battery systems. You should
treat it with care and pay attention to the following points:
• Handle the handset with care. Do not
drop or throw the handset down roughly.
• Do not immerse in any liquid. The
handset contains a liquid d etecti on sti cker
and the warranty will be voided by any
liquid damage.
• Do not place the handset near computer
disks, credit cards, and other magnetic
media. The information contained on
disks or cards may be erased or
damaged.
• Do not leave the handset or battery in
direct sunlight or near other heat sources
where the temperature could exceed 45
°C
• Keep the handset, battery, charger and
any other accessories away from
children.
• In the unlikely event of a battery leak
avoid contact with your eyes or skin. In
the event of contact please flush
thoroughly with water and consult a
doctor.
• Observe and obey warning si g ns at petrol
stations, airports and hospitals.
• The operation of some medical electronic
devices, such as hearing aids and
pacemakers, may be affected by the
handset.
• Take care not to allow metal objects such
as coins or keys to come into cont act with
the battery.
• Do not dispose of batteries in a fire.
• Do not throw used batteries into
household rubbish, return them to a
recycling point. (see Chapter 4)
• Do not connect the handset to any other
chargers or cigarette lighter chargers.
• Only use the supplied charger.
6
• Be careful not to pierce the battery with
sharp objects and do not use damaged
batteries.
• Do not disassemble or modify the battery.
• Stop using the battery if abnormal hea t,
odour, discolouration, deformation, or
abnormal condition is detected duri ng use,
charge, or storage.
• Do not put the battery in your mouth.
• Only use original replacement batteries.
• Do not attempt to dismantle the handset
or any of its accessories.
• Do not place the handset close to the
edge of a table in case it moves when set
on vibrate mode.
• Do not put the handset into a microwave
oven, dryer, or high-pressure container.
• Do not use your handset while driving or
operating other machinery.
• Do not use the handset where blasting is
in progress.
• Switch your phone off when boarding
aircraft.
• Do not leave your handset at the bottom
of a bag where it may be damaged by
sharp objects.
• Do not leave the handset discharged or
disconnected for a long time, otherwise
your personal data may be lost.
• Remember to make backup copies of all
important data on your handset
• Take care when your phone is in your
pocket. Sitting down may damage the
handset.
• It is normal for the handset to become
warm while the battery is being charged.
• Under poor network conditions battery life
is considerably reduced
• When the battery is thrown away cover
the terminals with insulating tape.
• Please recycle the packaging and all
parts as stated in Chapter 4.
7
Support Information
• For technical support please consult this manual and search our web site and FAQ
section at www.zte.com.au. For Warranty Service in the event of a fault please call 1800
670 796.
• Please do not call the warranty service line for general support enquiries.
• All calls for PIN numb er enquiries, Netwo rk problems, Telstra Next G Services, BigPond
account information, Web Access, Account and B illin g Inf ormatio n, US IM card reg istra tion
and general enquiries should be directed to Telstra on 125 111.
Warranty Information
The warranty does not apply to defects or errors in the produc t caused by:
disassembly of the product
(c) Water or any other liquid damage
(d) Any unauthorized repair or modification
(e) Power surges, lightning damage, fire, flood or other events outside ZTE’s reasonable
control
(f) Use of the product with any unauthor ized t hir d p ar ty produ ct s suc h as gener ic char gers
(g) Any other cause beyond the range of normal usage for products.
The End User shall have no right to reject, return, or receive a refund for any product from
ZTE under the above-mentioned situations.
8
Key Layout
Lock the handset by
holding down the * Key
Microphone
Camera
LCD
Left Select Key
Call key
Back key
Earpiece
Arrow Keys
(Left/Right/Up/Down/OK)
Right Select Key
End / Exit key
Clear key
Mute the handset by
holding down the # Key
9
Charger/USB port
and Headset jack
Left view
Notes
• The handset is available in various colours. For illustration purposes only the above
images are shown in teal / black.
• Keylock is enabled by holding the * Key.
• Mute is enabled by holding the # Key
10
Display Icons
Signal Strength of the GPRS
Network
Signal Strength of the 3G Network
New SMS/MMS Message
New E-mail
New Wap Push Message
SMS/MMS Memory is Full
GPRS Attach
PDP Context Established (Data)
HSDPA Service
Roaming
Alarm is set
11
Signal Strength of the EDGE Netw ork
Battery Level Indicator
No Battery Warning
Missed Call
Missed Video Call
Call Forward is Active
Silent Mode
Vibrate Mode
Headset Mode
Headset and Vibrate Mode
Bluetooth ON
1 Getting Started
1.1 Install the (U)SIM Card
The (U)SIM card (Universal Subscriber Interface Module) is the small plastic chip with gold
contacts supplied by Telstra. This contains your phone number and acts as a store for your
contacts. It can be mov ed betw een di f fere nt pho nes if requ ired. In sert thi s f ace dow n in to the
carrier inside the back panel of the phone. Make sure it is pushed all the way to the bottom of
the phone as shown below:
12
1.2Insert the Battery
Remove the back cover by pressing gen tly and sliding down. Insert the battery carefully with
the contacts located against the gold springs. The battery will only fit one way.
Close the case by locati ng the plastic cover into the grooves a nd sliding the cover up to
close it. Do NOT force the cov er do w n by pressi ng on it . This w ill dama ge the cov er. Slide the
cover up gently
Notes
• The battery is not fully charged when you buy your phone but there may be enough power in
the battery to turn the phone on.
• The battery takes two or three charge cycles to reach full capa city.
13
1.3Switch the Phone on and Connect the Charger
Press and hold the key for two seconds to switch your phone on. The phone takes
about 16 seconds to initialize. Enter the PIN number supplied by Telstra with your (U)SIM
card. The start up screen below is referred to throughout the manual as the Idle Screen :
Charge your Phone
Insert the charger lead carefully with the arrow on the top.
The lead only fits one way. Do NOT use excessive force
to insert the lead.
Check it is the right way round.
14
1.4Charging and Battery life
• Only use the charger supplied.
• Normal charge time is 2-3 hours.
• When not using the phone for a long period remove the battery and store it in a cool dry
place.
• Do not leave the phone connected to the charger for extended periods of time eg > 24
hrs.
• If the battery is not fully charged after 3 hours please stop charging.
• Charge the battery between 0°C~50°C. If the temperature of the handset is too high,
switch it off and let it cool.
• Battery life can be maximized by regularly allowing the phone to fully discharge before
recharging the battery.
• Charge the battery promptly when flat.
• Under poor network conditions (less than 2 bars) it is normal for the battery to only last 1
day.
• To maximize battery life turn off Bluetooth and reduce the back lighting to 10 seconds
(see Section 1.13 - ‘Personalise your Phone’).
• If the phone is not used for a long time or the battery is completely flat it may take a few
minutes to power up.
15
1.5Basic Navigation
From the Idle Screen press the OK Key to access the Main Menu:
The icons are described
at the bottom of the
screen.
Idle ScreenMain Menu
Arrow Keys
Use the Arrow Keys for shortcuts to menus, to move around the Main Menu and to move
the cursor
Up (Shortcut to My Place)
Left (Shortcut to E-Mail) Right (Shortcut to Messages)
Down (Shortcut to Contacts)
16
Select Keys
The two keys at the top of the keypad are called the Select Keys.
The left and right Select Keys are used to choose the options from the bottom of the
screen.
In the above example the Left Select Key opens Foxtel and the Right Select Key launches
BigPond
Back and Exit Keys
Press the key to go back one step or the key to Exit to the Main Menu.
17
1.6Enter your Contacts
There are several methods available to enter contacts into your phone. The Getting Started
Section deals with adding your contacts manually and copying contacts from a previous SIM
card. See the Advanced Section for adding contacts from your PC and importing contacts
from Microsoft Outlook. All contacts can be stored in Groups for easy management.
Adding Your Contacts Manually
• At the Idle Screen enter the phone n umber on the keypad then press the Left Select Key
to Save.
• Press the OK Key to Create New Contact.
• Add the person’s name using the abc keys (see notes on entering text in section 1.12).
• Press the OK Key to Save.
Copy Contacts from a previous SIM Card
• Insert your old SIM c ard. Switch the ph one on and press the Down Arrow Key to enter
Contacts
• Press the Right Arrow key once for (U)SIM to show th e list o f Contacts from your old SIM
card.
• Press Options, More, Copy all to phone, press OK to Sel ect and then press Yes to
confirm.
18
Add a contact from a received or dialled call number
You can save a new contact from an incoming or dialled call number:
• Press the key to bring up your Call List
• The last call will be at the top of the list
• Press the Right Select Key to Save the number
• Enter the contact name and any other details and press the OK Key to Save
Add a contact from a received SMS (Text Message)
You can save a Contact from a received SMS:
• Press the Right A rrow Key to access your SMS Menu and go to your Inbox
• View your message and press Options. Press Usehighlight object to save the
number
• Choose New Contact to create a new contact from the received SMS number
Searching Contacts
You can search your contacts by pressing the letter keys that correspond to your contact
name. From the contacts list press the initial letter to bring up the contacts associated with
that letter.
19
1.7Edit your Contacts to Change Ringtones and Groups
Once you have added some contacts you can edit them to change the Group and to set a
personalised Ring Tone.
• Contacts are normally stored in the default Group, Unclassified.
• You can move your contacts into other Groups: Mates, Family, Friends, Work, and VIP.
• Regardless of Group, all your contacts are displayed under All.
• From the Idle Screen go to your Contacts list by pressing the OK Key—Contacts or just
press the Down Arrow Key
• Use the arrow keys to search and press OK to View the required Contact.
• Press OK to Edit the Contact.
• When you are in Edit mode you can assign a specific Group and change the Ringtone if
desired.
• Use the Down Arrow key to navigate through the menu.
• Use the Right Select Key to Modify the incoming Ringtone.
• Use the Left or Right Arrow keys to change Groups.
• Changing the Ringtone to a personalised tune will let you recognise key callers instantly
by their unique tune.
20
1.8Set Speed Dials
Once you have entered some contacts you can assign speed dial keys to your chosen
contacts:
• Press Do wn Arrow Key to enter the Contacts menu.
• Use the Arrow Keys to scroll to the contact you wish to assign a Speed Dial Number.
• Press the Left Select Key for Options.
• Press 3 or scroll down to item 3 for Set Speed Dial.
• Assign your chosen contact to the next available number (1,2 and 3 are preset and
cannot be changed).
• Press the OK Key to Setup the speed dial (or to Cancel an existing speed dial).
• Press the key to exit when finished or the back key to choose another contact.
Make a call using Speed Dial
• From the Idle Screen press and hold the required Speed Dial Key to make a call to that
contact.
• E.g. A long press on the 1 key will automatically dial your voicemail number.
21
1.9 Make a Call
Dial the number manually
• If required press the * key twice for the International Prefix ‘+’.
• Enter the number on the keypad and press the key to make the call.
• When the call is connected you can press the OK Key for Handsfree mode.
• Press the key to end the call.
Choose a number from your Contacts list
• Press Do wn Arrow Key to enter the Contacts menu.
• Use the Up and Down Arrow Keys to scroll to your chosen contact.
• Press the key to make the call.
• When the call is connected you can press the OK Key for Handsfree mode.
• Press the key to end the call.
22
Choose a number from your call list (incoming, outgoing and
missed calls)
• Press the key to bring up your call list.
• Use the Up and Down Arrow Keys to scroll to the desired number (last number redial
select the top number).
• Press the key to make the call.
• When the call is connected you can press the OK Key for Handsfree mode.
• Press the key to end the call.
Notes
• The microphone is at the bo ttom of the han dset. Be ca reful n ot to blo ck i t wi th y our h ands .
• Press the Left Select Key for further options during a voice call. Use the Back key to
return to the call menu.
•Hold: Puts the current call on hold. You can dial a third party. Press hold again to switch
your two calls.
• End call: End the current call.
• Record: Record the current call. The audio file will save to Tools-Tools-File
Manager-Audios-My Audios.
• DTMF Off/On: Enable or disable sending DTMF tones. Default is ON.
• SMS: Switch to SMS interface during a call.
• Contacts: Switch to Contacts interface during a call.
23
1.10Receive a Voice Call
When you receive a voice call, the ring tone, illumination and vibrate function will activate (depending
on your current profile setting).
• Press the
• Press the Right Select Key or thekey to reject the call
• Press any key except the Right Select Key or thekey to mute the incoming call.
(The ring is muted but the call is not answered)
Note:
•When the headset is connected pressing the headset switch will answer the call.
key or the OK key to answer.
24
1.11Send an SMS (Text Message)
From the Idle Screen press the Right Arrow Key to open the Messages Menu:
• Press the OK Key to select New Message. Press the OK Key to select Text Message.
• Press the OK Key to select from your Contacts list or enter your number manually
• Select the chosen contact and press the OK Key twice to enter your contact.
• Press the Down A r row key twice to move the cursor into the text field.
• The default text mode is Predictive Text indicated by the En symbol for English (see 1.12
for more details).
• Enter your text by pressing the corresponding keys once for each letter you require eg
43556 for hello.
• Press Options to access My Words to add your own words to the dictionary (see 1.13)
• To change into conventional abc text mode press the # key to toggle between En, 123,
ABC and abc modes.
• When completed press the Right Select Key to Send your message.
25
1.12 Emergency Calls
To make an emergency call during normal use
1 Ensure that your handset is switched on and in service.
2 Press the key repeatedly to clear the display and return to the Idle Screen.
3 Enter the emergency number for your present location using the keypad, (eg 000)
4 Press key to call the number. Follow instructions received and do not end the call
until told to do so.
To make an emergency call without a (U)SIM Card
When the (U)SIM card is not inserted enter the emergency number and press or
to make the call.
Notes
• Tell the operator which service you require. Give your position and remain stationary to
get the best coverage.
• Due to the nature of the cellular system the connection of emergency calls cannot be
guaranteed.
• Never rely solely on any wireless device for essential communications like medical
emergencies.
26
Loading...
+ 60 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.