Zilog Z8F011A User Manual

Z8F08A28100KITG
Z8 Encore! XP® F082A Series Development Kit
UM018606-0109
Copyright ©2009 by Zilog®, Inc. All rights reserved.
www.zilog.com
Z8 Encore! XP® F082A Series Development Kit

Revision History

Each instance in Revision History reflects a change to this document from its previous revision. For more details, refer to the corresponding pages and appropriate links in the table below.
Revision
Date
January 2009
May 2008
March 2008
October 2005
February 2005
Level Description Page Number
06 Updated Hardware section. 1
05 Updated Introduction section. Changed
’Z8F08A28100KIT’ to ’Z8F08A28100KITG’.
04 Updated the new Zilog logo, implemented Style
Guide, and changed ZiLOG to Zilog. Changed title to Z8 Encore! XP F082A Series Development Kit. Modified Schematics Table 2 to incorporate changes to R15 from 220 Ω to 0 Ω. Added Note 3 to the Schematics.
03 F08xA Series development board, Corrected typo in
MCU features list: updated schematics for board rev C.
02 Introduction, Corrected Typo in development kit
name.
User Manual
ii
1
All
6, 9
1
UM018606-0109 Revision History
Z8 Encore! XP® F082A Series Development Kit

Table of Contents

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Software (on CD-ROM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Z8 Encore! XP F082A Series Development Board. . . . . . . . . . . . . . 5
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
MCU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
UART with IrDA Endec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Power and Communication Interfaces . . . . . . . . . . . . . . . . . . . . . . . 8
External Interface Headers JP1 and JP2 . . . . . . . . . . . . . . . . . . . . . 8
User Manual
iii
Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Customer Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
UM018606-0109 Table of Contents

Introduction

Zilog’s Z8 Encore! XP® F082A Series microcontroller unit (MCU) is a part of the line of Zilog’s MCU products. The Z8 Encore! XP F082A Series MCU development kit (Z8F08A28100KITG) enables you to become familiar with the hardware and software tools available with this product. This kit consists of the 8 KB version of the Z8 Encore! XP devel­opment board that supports and presents the features of the Z8 Encore! XP F082A Series. This kit allows you to begin writing application soft­ware and contains all supporting documents.
This manual acquaints you with the Z8 Encore! XP F082A Series MCU development kit, and provides instructions on setting up and using the tools to start building designs and applications. Z8F082ASJ020 is the sili­con used in the board. For more information, refer to Z8 Encore! XP F082A Series Product Specification (PS0228).
Z8 Encore! XP® F082A Series Development Kit
User Manual
®
1

Kit Contents

The Z8 Encore! XP F082A Series MCU development kit contains the following:

Hardware

The hardware in Z8 Encore! XP F082A Series MCU development kit include:
Z8 Encore! XP F082A Series development board
USB Smart Cable for PC to Z8 Encore! XP® F082A series develop­ment board (previous versions of the development kit used a serial smart cable; for information on using the serial smart cable, refer to your original documentation)
5 V DC power supply
UM018606-0109 Introduction
Z8 Encore! XP® F082A Series Development Kit
User Manual
Packaging
2
CD-ROM Containing
Documentation
Serial Smart Cable
Development Board
Power
Supply
Figure 1. Z8 Encore! XP® F082A Series Development Kit Contents

Software (on CD-ROM)

The software in Z8 Encore! XP F082A Series MCU development kit include:
ZDS II—Z8 Encore!® IDE with ANSI C-Compiler
Sample code
Document browser
Acrobat Reader
UM018606-0109 Introduction

Documentation

The following documents are included in the Z8 Encore! XP F082A Series development kit:
Quick Start Guide
Z8 Encore! XP F082A Series technical documentation (on CD-ROM) – Development Kit User Manual – ZDS II—IDE User Manual – eZ8 CPU User Manual – Application Notes
Z8 Encore! XP® F082A Series Development Kit
User Manual
3
The sample code is installed with ZDS II and is located in the
lation directory>\samples
The documentation can be installed with the DemoShield interface or viewed on the CD-ROM using the DemoShield menus and a PDF reader. A copy of the Acrobat installer is provided on the CD-ROM and can be installed from the DemoShield install screen. After installing the documentation, Windows Explorer can be used to select any document to be viewed with PDF file viewer.

System Requirements

An IBM PC (or compatible computer) with the following minimum configurations are required:
Microsoft Windows XP Professional SP1/Windows 2000 SP3/Win­dows NT 4.0 SP6/Windows 98 SE
Pentium II/233 MHz processor or higher up to Pentium IV, 2.8 GHz
96 MB RAM or more
25 MB hard disk space or more
Super VGA video adapter
<instal-
in the disk drive.
UM018606-0109 Introduction
CD-ROM
One or more RS-232 communication ports

Installation

Z8 Encore! XP® F082A Series Development Kit
User Manual
4
For details on installation and setup of the Z8 Encore! XP F082A Series development kit, refer to Z8 Encore! XP Quick Start Guide (QS0043).
®
/Z8 Encore!® Development Kits
UM018606-0109 Introduction
Z8 Encore! XP® F082A Series Development Kit

Z8 Encore! XP F082A Series Development Board

Introduction

Zilog’s Z8 Encore! XP® F082A Series development board is a development and prototyping board for the Z8 Encore! XP F082A Series MCU. The board provides you with a tool to evaluate features of Z8 Encore! XP F082A Series MCU, and to start developing an application before building the hardware.
User Manual
5
®
Figure 2. Z8 Encore! XP
UM018606-0109 Z8 Encore! XP F082A Series Development Board
F082A Series Development Board

Features

Z8 Encore! XP® F082A Series Development Kit
User Manual
The features of Z8 Encore! XP® F082A Series development board include:
Z8 Encore! XP MCU (28-pin SOIC)
3 LEDs
RS-232 interface
IrDA transceiver
Two pushbuttons, RESET and TEST
5 V DC power connector
On-Chip Debugger interface
6
20 MHz Ceramic Oscillator (Y1)
Header for ADC input
Prototyping area
External interface connectors JP1 and JP2
2.7 V–3.6 V operating voltage with 5 V-tolerant inputs
MCU
The Z8 Encore! XP F082A Series MCU is a member of the family of Zilog MCU products based on the 8-bit eZ8 core CPU. The Flash in-cir­cuit programming capability allows for faster development time and pro­gram changes in the field. The eZ8 core CPU is upward compatible with existing Z8 F082A Series makes it suitable for a variety of applications including motor control, security systems, home appliances, personal electronic devices, and sensors.
UM018606-0109 Z8 Encore! XP F082A Series Development Board
®
instructions. The rich peripheral set of the Z8 Encore! XP
Z8 Encore! XP® F082A Series Development Kit
User Manual
The development board contains circuitry to support and present all the features of the Z8 Encore! XP F082A Series. The key features of the Z8 Encore! XP F082A Series include:
eZ8 core CPU
8 KB Flash memory with in-circuit programming capability
1 KB register RAM
8-channel, 10-bit Analog-to-Digital Converter (ADC)
Full-duplex UART
Infrared Data Association (IrDA)-compliant infrared encoder/decoder
Two 16-bit timers with capture, compare, and PWM capability
Watchdog Timer (WDT) with internal RC oscillator
7
Eleven (20-pin package) or nineteen (28-pin package) I/O pins
Programmable priority interrupts
On-Chip Debugger
Voltage Brownout (VBO) Protection
Power-On Reset (POR)
2.7 V–3.6 V operating voltage with 5 V-tolerant inputs
Operating temperatures: 20 °C ±10 °C
®
For further information on the Z8 Encore!
Encore! XP
download at w
®
F082A Series Product Specification (PS0228), available for
ww.zilog.com.
family of devices, refer to Z8

UART with IrDA Endec

Z8 Encore! XP F082A Series (component U5) contains a fully-functional, high-performance UART with Infrared Encoder/Decoder (ENDEC). The Infrared Endec is integrated with an on-chip UART allowing easy
UM018606-0109 Z8 Encore! XP F082A Series Development Board
Z8 Encore! XP® F082A Series Development Kit
communication between the Z8 Encore! XP F082A Series and IrDA transceivers. Infrared communication provides secure, reliable, low-cost, point-to-point communication between PCs, PDAs, cell phones, printers, and other infrared enabled devices.

Power and Communication Interfaces

Table 1 lists jumper information concerning the shunt status, functions,
devices and defaults affected of jumpers JP3 and JP4.
Table 1. Jumpers JP3 and JP4
Device
Jumper Status
JP3* OUT RS-232
JP3 IN RS-232
JP4* OUT IrDA
JP4 IN IrDA
JP5 OUT U5 RESET
JP5 IN U5 RESET
*These jumpers must not be OUT at the same time.
Affected Status Default
interface
interface
interface
interface
/
PD0
/
PD0
User Manual
8
Enabled X
Disabled
Enabled
Disabled X
PD0 (GPIO) X
RESET when SW1 pressed

External Interface Headers JP1 and JP2

External interface headers JP1 and JP2 are displayed in Schematics on page 9.
UM018606-0109 Z8 Encore! XP F082A Series Development Board

Schematics

Figure 3 and Figure 4 on page 10 display the schematics for Z8 Encore! XP F082A Series development board.
Z8 Encore! XP® F082A Series Development Kit
User Manual
9
5
U6
PB1/ANA1 PB2/ANA2 PB3/CLKIN/ANA3 VDD PA0/T0IN /T0OUT/XIN/ PA1/T0OUT/XOUT GND PA2/DE PA3/CTS0 PA4/RXD0
Z8F04xAU6Z8F04xA
R150R15 0
C20C20
NOTE 2
R7
100R7100
R8
100R8100
R1010R10
10
20 pin footprint
VCC_33V
PB0/ANA0
PC3/COUT/LED
PC2/ANA6/LED
PC1ANA5/CINN/LED
PC0/ANA4/CINP/LED
DBG RESET/PD0 PA7/T1OUT
PA6/T1IN/T1OUT
PA5/TXD0
PA6_nT1OUT
PA7_T1OUT
D D
PC3_COUT
VCC_33V
GND
NOTE 3: Resistors R20 and R21 are not populated. See Note 2.
C C
R200R20
0
B B
D2
21
GREEND2GREEN
D3
21
YELLD3YELL
D4
21
REDD4RED
VCC_33V
GND
PA0_T0IN_JP
PA1_T0OUT_JP
R210R21
PB1_ANA1 PB0_ANA0
1
PB2_ANA2 PB3_ANA3 VCC_33V PA0_T0IN PA1_T0OUT GND PA2
Y1
1
2
2
20 MHzY120 MHz
2 3 4 5 6 7 8 9
10
R181MR18
1M
3
3
0
PA3_CTS0 PA4_RXD0
R140R14 0
1
C19C19
TABLE 2
Clock Mode R14 R15 R18 C19 C20 Y1
Internal Only none none none none none none
A A
Crystal 0 Ohm 0 Ohm none Yes Yes Yes
Ceramic Res 0 Ohm 0 Ohm none none none Yes
External CMOS none none none none none none
(Use PA0_T0IN pin on JP2)
5
R9
100KR9100K
20 19 18 17 16 15 14 13 12 11
4
R11
R11
100
100
VCC_33V
PC3_COUT PC2_ANA6 PC1_ANA5 PC0_ANA4
DBG
PD0 PA7_T1OUT PA6_nT1OUT PA5_TXD0
PA2
SW2SW2
TEST
GND
R120R12
0
U8
1
IO
IO
GND
2
EMI FilterU8EMI Filter
SENSE
C22
C22
C23
C23
+
+
0.033uF
0.033uF
30uF
30uF
0.033uF
0.033uF
R160R16
0
Note 1: PB6 and PB7 are dual function pins (GPIO or Analog supply) R12, R13, R16, and R17 are zero-ohm resistors used in conjunction with GPIO Control Registers to select function desired. C21, C22, and C23 are bypass capacitors that are used for better noise rejection. U8 is an optional filter that can be used to improve the quality of the Analog Supply. The development board is shipped configured for Analog Supply. Table 1 shows the configurations recommended
NOTE 1:
C10
C10
0.001uF
0.001uF
PA3_CTS0 PA4_RXD0
PA5_TXD0
0
R130R13
0
PB2_ANA2 PB4_ANA7
PB5
PB3_ANA3
VCC_33V PA0_T0IN PA1_T0OUT
GND
PA2
PA3_CTS0
PA4_RXD0 PC4
PA5_TXD0
PB7GND
3
C21
C21
R170R17
NOTE 1:
PB0_ANA0 PB2_ANA2
PB1_ANA1
C11
C11
C12
C12
0.001uF
0.001uF
0.001uF
0.001uF
Note 2: The XP supports internal, external crystal, external ceramic resonator, external R/C and external CMOS drive clock modes. R14, R15, R18, C19, C20 and Y1 are used to support the clock mode selected. The development board is shipped configured for external 20MHz ceramic resonator or internal clock operation. When using Internal oscilator, pins 7 and 8 could be used as GPIO ports PA0 and PA1. To do so install R20 and R21. Table 2 shows the recommended clock mode configurations.
4
PB3_ANA3
C13
C13
0.001uF
0.001uF
3
TABLE 1
R12 R13 R16 R17 R22 U8 C21...C23
GPIO OUT IN OUT IN IN OUT OUT
Analog IN OUT IN OUT OUT optional IN Supply
SW1SW1
GND
RESET/TEST2
JP5
PB6
R220R22
U5
U5
1
PB2/ANA2
2
PB4/ANA7
3
PB5/Vref
4
PB3/ANA3/CLKIN
5
PB6(AVDD)
6
VDD
7
PA0/T0IN /T0OUTXIN
8
PA1/T0OUT/XOUT
9
GND
10
PB7(AGND)
11
PA2/DE
12
PA3/CTS0
13
PA4/RXD0
14
PA5/TXD0
3
0
PB5_JP
28 pin footprint
Z8F04xA_28
Z8F04xA_28
PC0_ANA4
C14
C14
C15
C15
0.001uF
0.001uF
0.001uF
0.001uF
PC3/COUT/LED
PC2/ANA6/LED PC1/ANA5/CINN/LED PC0/ANA4/CINP/LED
PA6/T1IN/T1OUT
PC1_ANA5
PB0_ANA0
PB1_ANA1
PB2_ANA2
PB3_ANA3
PC0_ANA4
PC1_ANA5
PC2_ANA6
PB4_ANA7
JP5
HEADER 2
HEADER 2
28
PB1/ANA1
27
PB0/ANA0
26 25 24 23 22
DBG
21
RESET/PD0
20
PC7/LED
19
PC6/LED
18
PA7/T1OUT
17
PC5/LED
16
PC4/LED
15
PC2_ANA6 PB4_ANA7
C16
C16
0.001uF
0.001uF
J2
J2
1 3 5 7
9 11 13 15
HEADER 8X2
HEADER 8X2
1 2
PB1_ANA1 PB0_ANA0 PC3_COUT PC2_ANA6 PC1_ANA5 PC0_ANA4
DBG PD0 PC7 PC6 PA7_T1OUT PC5
PA6_nT1OUT
C17
C17
0.001uF
0.001uF
2 4 6 8 10 12 14 16
2
If Module is plugged onto the Dev Platform the local RS232 interface is disabled by pin 50 of JP2
PB4_ANA7 PC2_ANA6 PC1_ANA5 PB3_ANA3 PB1_ANA1
PC4 PC7
PA6_nT1OUT
PA7_T1OUT PA2
PA3_CTS0 PA4_RXD0 PA5_TXD0
R19
R19
10K
10K
PB6 PB7
-RESET
GND
VCC_33V
VCC_33V
1 3 5 7
9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59
1
JP2
JP2
connector 2
2
PC0_ANA4
4
PB2_ANA2
6
PB0_ANA0
8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50
-DIS_IrDA
52 54 56 58 60
HEADER 30x2/SM
HEADER 30x2/SM
GNDVCC_33V PC5 PC6
PB5_JPPC3_COUT PA0_T0IN_JP PA1_T0OUT_JPGND
PD0
GND
GND
GND
-DIS_232
-DIS_IRDA
connector 1
DBG
C18
C18
0.001uF
0.001uF
GND
Title
Title
Title
XP 4K MDS Processor Module. Schematic.
XP 4K MDS Processor Module. Schematic.
XP 4K MDS Processor Module. Schematic.
Size Document Number Rev
Size Document Number Rev
Size Document Number Rev
B
B
B
Date: Sheet
Date: Sheet
2
Date: Sheet
for reference
JP1
JP1
only
-TRSTN
-F91_WE
GND
A6 A0 A10
GND
A8 A13 A15
A19
A11 A4 A5
A21 A22
-CS0
-CS2 D1 D3
D7
-MREQ
GND
-WR
-BUSACK
96C0941-001 D
96C0941-001 D
96C0941-001 D
1 3 5 7
9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59
HEADER 30x2/SM
HEADER 30x2/SM
2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60
1
VCC_33V
A3
VCC_33V
A7
A9 A14 A16A18
GND A1A2 A12 A20
A17
-DIS_FLASH VCC_33V
A23
-CS1
D0
D2
D4 GNDD5
D6
-IOREQ
-RD
-INSTRD
-BUSREQ
23Tuesday, March 18, 2008
23Tuesday, March 18, 2008
23Tuesday, March 18, 2008
of
of
of
Figure 3. Schematic, Z8 Encore! XP® F082A Series MCU Development Board
UM018606-0109 Schematics
Z8 Encore! XP® F082A Series Development Kit
User Manual
10
5
J1
J1
2 3 1
PWR JACK
PWR JACK
D D
GND
C C
GND
B B
A A
F1
RXE050F1RXE050
R23
R23 10K
10K
SENSE
R24
R24 15K
15K
147
3 4
147
5 6
147
11 10
147
13 12
5
U3B
U3B
74LVC04/SO
74LVC04/SO
U3C
U3C
74LVC04/SO
74LVC04/SO
U3E
U3E
74LVC04/SO
74LVC04/SO
U3F
U3F
74LVC04/SO
74LVC04/SO
-Z_RST
U7
U7
5
VIN
2
SENSE
4
SHDN
LT1129-3.3/DD
LT1129-3.3/DD
OUT
GND
3
4
5V
C4
0.1uFC40.1uF
1
0.1uFC80.1uF
C8
TP1TP1
+
C3
+
C3
100/10
100/10
12345
4
GND
VCC
+
+
100/10
100/10
VCC_33V
VCC_33V
R1
C7
C7
680R1680
21
D1
3.3 OK
LEDD1LED
GND
VCC_33V
12345
TP2TP2
3
VCC_33V
3
GND
VCC_33V
-DIS_232
R2 10KR210K
JP3JP3
1 2
DIS RS232
-DIS_IRDA
JP4JP4
1 2
DIS IRDA
DBG INTERFACE
P2
1 2 3 4 5 6
Header 3x2P2Header 3x2
PA5_TXD0
PA3_CTS0
PA4_RXD0
GND
PA5_TXD0
147
1 2
R5 10KR510K
-Z_RST DBG
C2
0.1uFC20.1uF
C6
0.1uFC60.1uF
GND
PA3_CTS0
PA4_RXD0
U3A
U3A
74LVC04/SO
74LVC04/SO
VCC_33V
GND
R6 10KR610K
2
4
5
6
13
12
15
10
1
20
147
9 8
DBG
2
U1
C1+
C1-
C2+
C2-
T1IN
T2IN
R1OUT
R2OUT
EN
SHDN
MAX3222U1MAX3222
U3D
U3D
74LVC04/SO
74LVC04/SO
2
5
1
2
4
3
6
GND
TXD0 CTS0 RXD0
C9
330nFC9330nF
U4
VCC
LEDA
TXD
SD
RXD
GND
1
C1
0.1uFC10.1uF
1 6 2 7 3 8 4 9 5
DB9 Female
DB9 Female
USER
T
ZHX1810U4ZHX1810
0
1
VCC_33V
19
3
V+
VCC
C5
7
V-
17
T1OUT
8
T2OUT
16
R1IN
9
R2IN
14
NC
11
NC
GND
18
GND
Title
Title
Title
Size Docum ent Number Rev
Size Docum ent Number Rev
Size Docum ent Number Rev
B
B
B
Date: Sheet
Date: Sheet
Date: Sheet
0.1uFC50.1uF
R368R3
68
R4
2R7R42R7
PA5_TXD0
IRDA_SD
PA4_RXD0
XP 4K MDS Processor Module. Schematic.
XP 4K MDS Processor Module. Schematic.
XP 4K MDS Processor Module. Schematic.
96C0941-001 D
96C0941-001 D
96C0941-001 D
CONSOLE
P1
P1
of
of
of
33Wednesday, March 12, 2008
33Wednesday, March 12, 2008
33Wednesday, March 12, 2008
Figure 4. Schematic, Z8 Encore! XP® F082A Series MCU Development Board
UM018606-0109 Schematics
Z8 Encore! XP® F082A Series Development Kit

Customer Support

For answers to technical questions about the product, documentation, or any other issues with Zilog’s offerings, please visit Zilog’s Know ledge Base at http://www.zilog.com/kb
For any comments, detail technical questions, or reporting problems, please visit Zilog’s Technical Support at http://support.zilog.com
User Manual
11
.
.
UM018606-0109 Customer Support
Z8 Encore! XP® F082A Series Development Kit
User Manual
12
Warning:
DO NOT USE IN LIFE SUPPORT
LIFE SUPPORT POLICY
ZILOG’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF ZILOG CORPORATION.
As used herein
Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.
Document Disclaimer
©2009 by Zilog, Inc. All rights reserved. Information in this publication concerning the devices, applications, or technology described is intended to suggest possible uses and may be superseded. ZILOG, INC. DOES NOT ASSUME LIABILITY FOR OR PROVIDE A REPRESENTATION OF ACCURACY OF THE INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED IN THIS DOCUMENT. ZILOG ALSO DOES NOT ASSUME LIABILITY FOR INTELLECTUAL PROPERTY INFRINGEMENT RELATED IN ANY MANNER TO USE OF INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED HEREIN OR OTHERWISE.The information contained within this document has been verified according to the general principles of electrical and mechanical engineering.
Z8, Z8 Encore!, and Z8 Encore! XP are registered trademarks of Zilog, Inc. All other product or service names are the property of their respective owners.
UM018606-0109
Loading...