Zephyr ZGE-E30AS290, ZGE-E30AS, ZGE-E36AS, ZGE-E36AS290 User Manual

Genova
ZGE-E30AS ZGE-E36AS ZGE-E30AS290 ZGE-E36AS290
www.zephyronline.com
Model number: Serial Number:
Use, Care, and Installation Guide
JUL11.0301 © Zephyr Corporation
www.zephyronline.com
SAFETY NOTICE ................................................................. 2-3
LIST OF MATERIALS ....................................................... 4
INSTALLATION
Ducting Calculation Sheet
....................................... 5
Mounting Height & Clearance Ducting Options Hood Specifi cations Preparing the Cabinet Installing the Hood Ductless Recirculation
........................................................... 7
................................................... 8
............................................... 9
...................................................... 10 - 12
.............................................. 13
FEATURES & CONTROLS
Touch Controls Remote Control (Optional)
.............................................................. 14-15
....................................... 16
MAINTENANCE
Hood and Filter Cleaning Lights
................................................................................ 18
Wiring Diagram
TROUBLESHOOTING
............................................................ 19
................................................................ 20
......................................... 17
LIST OF PARTS AND ACCESSORIES
................................ 6
Table of Contents
.............................. 21
READ AND SAVE THESE INSTRUCTIONS
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE.
WARNING
TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a. Use this unit only in the manner intended by the manufacturer, if you have questions, contact the manufacturer.
b. Before servicing or cleaning unit, switch power off at service panel and lock panel to prevent power from being switched on accidentally.
When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
CAUTION
For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. Take care when using cleaning agents or detergents. Suitable for use in household cooking area.
WARNING
TO REDUCE THE RISK OF RANGE TOP GREASE FIRE: a. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly
on low or medium settings.
b. Always turn hood ON when cooking at high heat or when fl aming food
Important Safety Notice
c. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or fi lter. d. Use proper pan size. Always use cookware appropriate for the size of the surface element. e. Keep fan, fi lters and grease laden surfaces clean. f. Use high setting on hood only when necessary. g. Don’t leave hood unattended when cooking. h. Always use cookware and utensils appropriate for the type of and amount of food being prepared.
www.zephyronline.com
WARNING
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP FIRE, OBSERVE THE FOLLOWING: a. SMOTHER FLAMES with a close-fi tting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS.
If the fl ames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT. b. NEVER PICK UP A FLAMING PAN – You may be burned. c. DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion will result. d. Use an extinguisher ONLY if:
1. You know you have a Class ABC extinguisher, and you already know how to operate it.
2. The fi re is small and contained in the area where it started.
3. The fi re department is being called.
4. You can fi ght the fi re with your back to an exit
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a. Installation work and electrical wiring must be done by qualifi ed person(s) in accordance with all applicable codes and standards.
Including fi re-rated construction. b. Suffi cient air is needed for power combustion and exhausting of gases through the fl ue (chimney) of fuel burning equipment to prevent
back-drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National
Fire Protection Association (NFPA) and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and
the local code authorities. c. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities. d. Ducted fans must always vent to the outdoors. e. NEVER place a switch where it can be reached from a tub or shower. f. Make sure the power is off before installing, wiring or maintenancing.
WARNING
TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.
CAUTION
To reduce risk of fi re and to properly exhaust air outside - Do not vent exhaust air into spaces within walls, ceilings, attics, crawl spaces or garages. Hood not intended for installation over an outdoor grill.
OPERATION
Always leave safety grilles and fi lters in place. Without these components, operating blowers could catch onto hair, fi ngers and loose clothing.
The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation, maintenance and suitable use of the product. The manufacturer further declines all responsibility for injury due to negligence and the warranty of the unit automatically expires due to improper maintenance.
*NOTE: Please check www.zephyronline.com for revisions before doing any custom work.
ELECTRICAL REQUIREMENTS
Important:
Observe all governing codes and ordinances. It is the customer’s responsibility:
- To contact a qualifi ed electrical installer.
- To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 latest edition* or CSA standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** and all local codes and ordinances.
If codes permit and a separate ground wire is used, it is recommended that a qualifi ed electrician determine that the ground path is adequate.
Do not ground to a gas pipe. Check with a qualifi ed electrician if you are not sure the range hood is properly grounded. Do not have a fuse in the neutral or ground circuit. *National Fire Protection Association Batterymarch Park, Quincy, Massachusetts 02269
** CSA International 8501 East Pleasant Valley Road, Cleveland, Ohio 44131-5575 This appliance requires a 120V 60Hz electrical supply and connected to an individual properly grounded branch circuit
protected by a 15 or 20 ampere circuit breaker or time delay fuse. Wiring must be 2 wire with ground. Please also refer to Electrical Diagram on product.
A cable locking connector (not supplied) might also be required by local codes. Check with local requirements, purchase and install appropriate connector if necessary.
ZGE-E30AS, ZGE-E36AS - 370 Watts, 3.1 Amps ZGE-E30AS290, ZGE-E36AS290 - 167 Watts, 1.4 Amps
Important Safety Notice
MODELS: ZGE-E30AS, ZGE-E30AS290, ZGE-E36AS, ZGE-E36AS290
PARTS SUPPLIED
List of Materials
www.zephyronline.com
(1) 6” round damper (pre-installed)
(1) hood body with sliding glass
(2) upper installation brackets
(2) lower installation brackets
(1) filler panel (pre-installed)
(1) decorative mesh filter
HARDWARE PACKAGE CONTENTS
(4) 3/16 x 3/8”
(2) M4 x 8 (2) M4 x 1”
PARTS NOT SUPPLIED
- Ducting, conduit and all installation tools
- Cable connector (if required by local codes)
- Recirculating kit accessory - ZRC-00GE
- Remote control accessory - 14000005
(4) 3/16 x 1”
(2) halogen lights, GU-10 50W
(1) hardware package
(3) Wire Nuts
(1) Suction Cup
Duct pieces
3- 1/ 4” x 10” Rect., straight
Equivalent number length x used =
1 Ft. x ( ) =
To t a l
Ft.
Duct pieces
6”- 8” Round wall cap with damper
Equivalent number length x used =
30 Ft. x ( ) =
To t a l
Ft.
7” Round, straight
8” Round, straight
3- 1/ 4” x 10”
0
Rect. 90 elbow
3- 1/ 4” x 10”
0
Rect. 45 elbow
3- 1/ 4” x 10”
0
Rect. 90 flat elbow
3- 1/ 4” x 10” Rect. wall cap with damper
3- 1/ 4” x 10” Rect. to 6” round transition
3- 1/ 4” x 10” Rect. to 6” round transition
0
elbow
90
6” Round,
0
elbow
90
1 Ft. x ( ) =
1 Ft. x ( ) =
15 Ft. x ( ) =
9 Ft. x ( ) =
24 Ft. x ( ) =
30 Ft. x ( ) =
5 Ft. x ( ) =
20 Ft. x ( ) =
15 Ft. x ( ) =
Ft.
Ft.
Ft.
Ft.
Ft.
Ft.
Ft.
Ft.
Ft.
6”- 8” Round, roof cap
6” round to 3- 1/ 4” x 10” rect. transition
6” round to 3- 1/ 4” x 10” rect. transition
0
elbow
90
7” or 8”
Round,
0
90
elbow
7” or 8”
Round,
0
45
elbow
7” or 8”
Round
wall cap with damper
7” or 8” Round, roof cap
7” round to 3 1/ 4” x 10” rect. transition
7” round to 3- 1/ 4” x 10” rect. transition
0
elbow
90
30 Ft. x ( ) =
1 Ft. x ( ) =
16 Ft. x ( ) =
15 Ft. x ( ) =
9 Ft. x ( ) =
30 Ft. x ( ) =
30 Ft. x ( ) =
8 Ft. x ( ) =
23 Ft. x ( ) =
Ft.
Ft.
Ft.
Ft.
Ft.
Ft.
Ft.
Ft.
Installation – Ducting Calculation Sheet
Ft.
6” Round,
0
elbow
45
9 Ft. x ( ) =
Subtotal column 1 =
Maximum Duct Length: For satisfactory air movement,
the total duct length of a 3 1/ 4” x 10” rectangular 6” or 7” diameter round duct should not exceed 100 equivalent feet.
Ft.
Ft.
Subtotal column 2 =
Subtotal column 1 =
Total ductwork =
Ft.
Ft.
Ft.
24” min. 32” max.
36”
Installation – Installing the Hood
www.zephyronline.com
Mounting height from top of cooking surface to bottom of hood should be no less than 24” and no more than 32”.
It is important to install the hood at the proper mounting height. Hoods mounted too low could result in heat damage and fi re hazard while hoods mounted too high will be hard to reach and will lose performance and effi ciency.
If available, also refer to range manufacturer’s height clearance requirements and recommended hood mounting height above range. Always check your local codes for any differences.
DAMAGE-SHIPMENT / INSTALLATION:
• Please fully inspect unit for damage before installation.
• If the unit is damaged in shipment, return the unit to the store in which it was bought for repair or replacement.
• If the unit is damaged by the customer, repair or replacement is the responsibility of the customer.
• If the unit is damaged by the installer (if other than the customer), repair of replacement must be made by arrangement between customer and installer.
DUCTING
A minimum of 6” round ducting must be used to maintain maximum air fl ow effi ciency.
Always use rigid type metal ducts only. Flexible ducts could restrict air fl ow by up to 50%.
Use calculation worksheet to compute total duct work.
ALWAYS, when possible, reduce the number of transitions and turns. If a long duct run is required, increase duct size from 6” to 7” or 8”.
If turns or transitions are required: Install as far away from opening and as far apart, between 2, as possible.
WARNING FIRE HAZARD
NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside, unless using the recirculating option.
Use single wall rigid Metal ductwork only.
Fasten all connections with sheet metal screws and tape all joints w/ certifi ed Silver Tape or Duct Tape.
Ducting Options Example
roof pitch w/ flashing & cap
Installation – Ducting Options
ductless recirculating
side wall cap w/ gravity damper
soffit or crawl space
ductless recirculating
soffit
www.zephyronline.com
front of hood
11
"
19
16
500mm
15
29
16
760mm
35
"
912mm
side of hood
1
"
9
"
5
8
1
41mm
11"
280mm
7
"
8
3"
76mm
"
1
8
1
28mm
"
6
153mm
1
4
6mm
242mm
11
286mm
to
"
2
1 4
35mm
"
3
"
1
8
Installation – Hood Specifi cations
top of hood
6
153mm
"
"
5
8
18
473mm
to
"
1
2
17
445mm
blower outlet
1
7
16
180mm
"
junction box
"
3
4
7
197mm
"
5
8
16mm
9/16”
-
7”
19-
C/L
Fig.1
7/8”
7
9-
3/4
7/8”
Installation – Preparing the Cabinet
front edge
glass handle
Fig.2
1. Determine and mark center line on wall and cabinet bottom with a pencil.
2. If the cabinet bottom is recessed, wood blocking must be installed to ensure proper alignment of the hood with the cabinet bottom. Wood blocking should be fl ush within cabinet bottom.
3. Follow the dimensions in Fig.1 and cut-out the bottom of your cabinet to create an opening for the hood to fi t through. If you have a frameless cabinet begin the 1-9/16” measurement (referenced in Fig.1) from front of the cabinet door. This way the front edge of the hood will be fl ush with the cabinet doors when closed, see Fig.2.
www.zephyronline.com
WARNING: Electrical wiring must be done by a qualified person(s) in
!
accordance with all applicable codes and standards. This range hood must be properly grounded. Turn off electrical power at service entrance before wiring.
1) Prepare electrical wiring and ducting in cabinet. Location of junction box and blower outlet can be found on page 8.
Fig.3 Fig.4
2) Unscrew the (10) screws from front panel and place the panel aside, Fig.3. You will now have access to the interrior of the range hood.
3) Open cabinet doors. Lift range hood and slide it through
the opening located in the bottom of the cabinet, Fig.4. Make sure opening matches the dimensions on page 9, Fig.1.
Installation – Installing the Hood
Fig.5 Fig.6
4) There are spring clips located on the left and right sides of the hood body which will temporarily hold the hood in place, Fig.5.
2
1
5) Secure upper brackets to left and right sides of hood
body by using (2) 3/16 x 3/8” screws for each bracket. Fig.6. Make sure the (2) captive nut screw holes on the bracket are facing downward. Note: Due to limited workspace in 30” cabinets you will need to use a right angle or 2” long Philips head screwdriver.
10
Fig.7 Fig.8
6) Place lower installation brackets under upper installation brackets located on left and right sides of hood body, Fig.7. Note: The wider portion of the lower installation bracket should be at the bottom.
2
1
1
7) From inside the hood, secure (1) M4x8 screw into each lower installation bracket. The position of this screw is adjustable to accomodate various cabinet bottom thicknesses, Fig.8. Do not fully tighten screw yet.
Installation – Installing the Hood
Fig.9 Fig.10
8) Install (2) 3/16x1” screws into the captive nuts of each upper installation bracket. Tighten screws to adjust the height of range hood until there is no gap between the cabinet bottom and front edge of hood, Fig.9. After hood is positioned, fully tighten the lower installation bracket screw from step 7, Fig.8-1.
B
A
9) A fi ller panel is included to accomodate multiple cabinet depths. Inside the hood are (2) thumb screws located on the left and right sides at the back of the hood, Fig.10A. Turn each thumb screw clockwise to push the fi ller panel towards the wall, Fig.10B. Tighten thumb screws until fi ller panel meets the wall and is secured in place. See hood specifi cations on page 8 for supported cabinet depths.
11
Fig.11 Fig.12A
10) Place 6” round ducting over blower collar and secure with aluminum duct tape. If using hood in ductless recirculating mode turn to page 13.
Install electrical wiring. Note: A cable lock (not included) may be required by local codes. Check with local requirements and codes, purchase and install appropriate connector if necessary.
www.zephyronline.com
A
11) Secure (2) 1” wood screws (A) into the screw holes on
the left and right sides of the fi lter opening. This will secure the hood body to the cabinet base and prevent the hood from shifting after installation.
Make sure no packing material is inside hood. Power
Installation – Installing the Hood
up hood check for leaks around duct tape and verify all functions.
Fig.12B
12) Place front panel back on hood body and secure in place by using the (10) screws previously removed from step 2.
12
Ductless recirculation is intended for applications where an exhaust duct work is not possible to be installed. When converted, the hood functions as a recirculating hood rather than an exhaust hood. Fumes and exhaust from cooking are drawn and fi ltered by an optional charcoal fi lter. The air is then purifi ed and recirculated back within the home.
We recommend to ALWAYS exhaust air outside of the home by employing existing or installing new duct work, if possible. The hood is most effective and effi cient as an exhaust hood. Only when the exhaust option is not possible should you recourse to converting the hood into a recirculating hood.
When converted to be a recirculating hood, a charcoal fi lter is required on top of the decorative mesh fi lter. Order according to its part number below. The decorative mesh fi lter is intended to capture residue from cooking and the optional charcoal fi lter helps to purify fumes exhausted from cooking for recirculation.
RECIRCULATING KIT (REQUIRED IF NOT DUCTED OUTSIDE THE HOME)
Kit includes charcoal fi lter, brackets and return air vent.
Hood Model Part No. Filters in Pkg.
ZGE (all models) ZRC-00GE 1
1. Purchase recirculating kit per the part number above.
2. Remove decorative mesh fi lter from hood and place charcoal fi lter on top of mesh fi lter. Secure charcoal fi lter to mesh fi lter by using the supplied wire brackets as shown in Fig.13.
3. Reinstall decorative mesh fi lter.
4. In order to recirculate the air properly, a return air vent must be installed to allow recycled air to be returned to the kitchen, Fig. 14. Ducting must be run from the blower to the return air vent. The return air vent can be positioned on top of the cabinet or in a soffi t/ceiling.
5. Enable Charcoal Filter Change indicator on control panel. See page 15.
6. Charcoal fi lter must be replaced after every 120 hours of use or approximately every 3 to 4 months based on an average daily use of 1 hour of cooking time) The microprocessor in the controls, when set, will elapse and count usage time and indicate when charcoal fi lter replacement is required every 120 hrs.
Installation – Ductless Recirculation
Charcoal Filter Replacement
Hood Model Part No. Qty to Order
ZGE (all models Z0F-C0GE 1
Fig.14
Fig.13
13
www.zephyronline.com
Blower On/Off
NOTE: Blower and lights will automatically shut off when the glass is closed. The hood
also has a built in memory function that will automatically turn the blower and lights on at the last setting when the glass is pulled open. Blower will not operate while the glass is closed but the lights will still function.
1
Blower On/Off
By pressing , the blower is switched On and Off. When switched On, the blower will operate at the last setting before it was switched Off. When switched Off the entire hood powers Off, including the lights.
2
Speed Selection
The 3 speed levels are selected by pressing to decrease and to increase speed level. The display indicates speed level selected. Pressing when the hood is Off will also switch the blower On.
Display (speed level, delay of
Speed Selection
5 Min Delay Off
f, filter clean/replace)
Lights Normal/Dim/Off
Delay Off
3
Features & Controls – Touch Controls
Delay Off is used for programmed shut down of blower and lights 5 minutes after the function is activated. Press once and a dot will appear in the lower right side of the Display indicating the function is on. The hood will change to Speed 1 and shut down after 5 minutes.
Lights Normal/Dim/Off
4
Switch lights on to Normal by pressing once, again to Dim and again to switch Off.
Display
5
Displays blower speed level, delay off status, mesh filter clean and charcoal filter replace notification.
The decorative mesh filter is required to be cleaned frequently and as recommended in order to maintain blower efficiency. If improperly maintained, residue from cooking will sift through filter and cause damage to hood blower and other sensitive components by possibly clogging duct work and creating a fire hazard.
14
Decorative Mesh Filter Clean Reminder (metal mesh filter)
F
F
F
F
F
C
C
C
C
C
C
C
Whether your hood is installed as an exhaust or purifying unit, a decorative mesh filter is fitted by the factory. This mesh filter is intended to filter out residue from cooking. It need not be replaced on a regular basis but is required to be kept clean. After every 30 hours of use the Filter Clean Reminder function in the microprocessor will automati­cally remind you by a flashing when the mesh filter needs to be cleaned. The filter can be cleaned by hand with non-abrasive soap or in a dishwasher. A heavily soiled filter should also be soaked in grease cutting detergent prior to cleaning.
Decorative Mesh Filter Clean Indicator
When flashes on display, the mesh filter installed is required to be cleaned. This will occur after every 30 hours of use.
Re-setting Function
Reset the filter clean reminder timer when filter is cleaned and re-installed. With hood off, press and hold for approximately 5 seconds until on display disappears . . The filter clean reminder function is now reset and a new 30 hours elapse cycle is initiated.
Clean Filters
display < F > flashes
To Re set
hold 5 sec. display from < F > to < >
Charcoal Filter Replace Reminder (charcoal filter, if installed)
When your hood is installed as a recirculating unit it must be fitted with a charcoal filter to purify exhaust and fumes from cooking and then recirculate the air within the home. This charcoal filter must be replaced after every 120 hours of use. The charcoal filter should never be cleaned or placed in a dish washer.
The charcoal filter replace reminder function in the microprocessor needs to be switched on. When switched on, the microprocessor will elapse and count usage time. When charcoal filter replacement is needed a flashing will appear on the display.
Setting the Charcoal Filter Replace Reminder
With hood off, hold for approximately 5 seconds. The display will change from (exhaust mode) to (recirculating mode). This indicates that the elapse timer function is switched on and charcoal filter is being used.
Set Mode
hold 5 sec. display from < - > to < C >
Charcoal Filter Replace Indicator
When the display starts flashing, the charcoal filter needs to be replaced. Purchase replacement charcoal filters from Zephyr.
Re-setting Function
After charcoal filter is replaced, with hood off, press and hold for apprimately 5 seconds until on the display disappears . The filter change reminder is now re-set and a new 120 hour elapse cycle is initiated.
15
Set Mode
Change FIlter
display < C > flashes
To Re set
hold 5 sec. display from < C > to < >
Features & Controls – Filter Clean and Replace Reminder
www.zephyronline.com
FCC Caution: To assure continued compliance, any changes or modifi cations not expressly approved by the party
responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Remote control is sold as an optional accessory. Purchase Zephyr part number: 14000005
This remote control may operate in humid environments, but not when placed on a wet surface.
SYNCHRONIZATION: To create a unique link between your range hood and remote control please follow the below steps:
1. With range hood off, press and hold the “lights” button on the range hood until the letter “F” shows on the display screen.
2. Press the “lights” button on the remote, the lights on the hood will turn on. The synchronization is complete.
REMOTE CONTROL FEATURES:
The RF remote control is equipped with a magnet for easy storage. The remote may be placed on any magnetic surface such as a refrigerator or the Zephyr remote holder. Maximum remote control communication distance from power pack is 15 feet.
Blower On/
Speed Selection
5 Min Delay Off
1
3
Blower On/
2
Power Off
4
Lights On/Dim/Off
1
Blower On/Speed Selection
By pressing , the blower is switched On. Press again to cycle through all three blower speeds.
2
Blowers On/Hood Off
By pressing , the blowers will power on at the last speed setting. Press again and the entire hood will power off, including lights.
Delay Off
3
By pressing , the blower and lights will enter Delay Off mode. A dot will appear in the lower right corner of the power pack display indicating the function is on. The blower will change to speed 1 and shut down after 5 minutes.
Lights On/Dim/Off
4
Switch lights On by pressing once, again to dim and again to switch Off.
REMOTE CONTROL MAINTENANCE:
Clean the remote control using non abrasive detergents
Follow instructions below for replacing battery.
Features & Controls – Remote Control (Optional)
+
A
-
Using a small fl at head screwdriver, raise the cover of the battery door (A) in order to access the battery compartment.
Remove the battery and replace with Type A23 12V. Negative end of battery should face the spring inside the remote.
Replace battery door and recycle old battery.
16
SURFACE MAINTENANCE:
Periodically clean with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent steel wool or scouring pads which will scratch and damage surface.
For heavier soil use liquid degreaser.
After cleaning it is recommended that you use non-abrasive stainless steel polish/cleaners to polish and buff out the stainless luster and grain. Always scrub lightly with clean cotton cloth and with the grain.
Do not use any product containing chlorine bleach. Do not use “orange” cleaners.
Decorative Mesh Filters
The mesh fi lter installed by the factory is intended to fi lter out residue and grease from cooking. It need not be replaced on a regular basis but is required to be kept clean.
Filter should be cleaned after every 30 hours of use or once a month.
Remove and clean by hand or in dishwasher on low heat. Spray degreasing detergent and leave to soak if heavily soiled.
Dry fi lter and re-install before using hood.
Replacing Mesh Filter
Should fi lter wear out due to age and prolonged use, replace with the following part number:
Hood Model: Part No. Qty. to Order.
All ZGE Models 50200036 1
Replace any damaged fi lter that has punctured or broken mesh or damaged frame.
To remove decorative mesh fi lter:
1. Pull down on handle.
2. Tilt fi lter down and remove from hood.
Maintenance – Hood and Filter Cleaning
1
2
17
Maintenance – Lights
www.zephyronline.com
REPLACING LIGHT BULBS
CAUTION: Light bulb becomes extremely hot when turned on.
DO NOT touch bulb until switched off and cooled. Touching hot bulbs could cause serious burns.
Make sure all power is turned off and bulbs are not hot.
Remove by turning bulb counter-clockwise. Note: Bulb does not unscrew; it turns 60 degrees, stops and falls out.
If bulbs are diffi cult to turn due to prolonged use, fi rmly attach a glass suction cup approximately the diameter of the bulb or use a rubber/latex glove to grip the bulb and turn counter clockwise.
Replacement bulbs are available at specialty lighting stores. Purchase type (MR16) GU-10 50W halogen.
For Zephyr part numbers please turn to page 21 of the manual.
18
370W
270W
Maintenance – Wiring Diagram
19
TROUBLESHOOTING PROCEDURES FOR GENOVA
Issue Cause What to do
After installation, the unit doesn’t work.
Troubleshooting
Light works, but motor is not turning.
The unit is vibrating.
The motor is working, but the lights are not.
The hood is not venting out properly.
Metal fi lter is vibrating.
RF Remote control does not work
1. The power source is not turned ON. 1. Make sure the circuit breaker and the unit’s
2. The power line and the cable locking connector is not connecting properly.
3. The switch board and control board wirings are disconnected.
4. The wires on control board are loose. 4. Make sure the wires on the control board are
5. The switch board or control board is defective. 5. Change the switch board or control board.
1. The blower is defective, possible seized. 1. Change the blower.
2. The thermally protected system detects if the motor is too hot to operate and shuts the motor down.
3. Damaged capacitor. 3. Change the capacitor.
4. The blower wire is not connected. 4. Make sure the blower wire is plugged into the
1. The blower is not secure in place. 1. Tighten the blower screws in place.
2. Damaged blower wheel. 2. Change the blower.
3. The hood is not secured in place. 3. Check the installation of the hood.
1. Defective halogen bulb. 1. Change the halogen bulb.
2. The light bulb is loose. 2. Tighten the light bulb.
3. The wires on the control board are loose. 3. Make sure the wires on control board are
1. The hood might be hanging too high from the cook top.
2. Wind from opened windows or opened doors in the surrounding area is affecting the ventilation of the hood.
3. Blockage in the duct opening or duct work. 3. Remove all the blocking from the duct work or
4. The direction of duct opening is against the wind. 4. Adjust the duct opening direction.
5. Using the wrong size of ducting. 5. Change the ducting to correct size.
1. Mesh fi lter is loose. 1. Change the mesh fi lter.
2. Handle spring clip does not work properly 2. Adjust the handle until the spring clip works
1. Battery is dead 1. Replace battery with type A23 12v
2. Poor communication with the hood 2. Remote control must be within 15 ft of hood
3. RF remote lost communication with hood 3. Reset hood and remote by switching power
www.zephyronline.com
power is ON.
2. Check the power connection with the unit is connected properly.
3. Make sure the wirings between the switch board and control board are connected properly.
connected properly.
2. The motor will function properly after the thermally protected system cool down.
molex connector.
connected properly.
1. Adjust the distance between the cook top and the bottom of the hood within 24” and 32” range.
2. Close all the windows and doors to eliminate the outside wind fl ow.
duct opening.
off at the circuit breaker for 5 minutes. Place remote on counter top near hood and switch the circuit breaker back on.
20
DESCRIPTION PART#
Replacement Parts
Light Bulb GU10 50W (each) Z0B0020 Decorative Mesh Filter 50200036
Optional Accessories
Recirculating Kit ZRC-00GE Replacement Charcoal Filter (each) Z0F-C0GE RF Remote Control 14000005
To order parts, visit us online at http://store.zephyronline.com or call us at 1.888.880.8368
List of Parts and Accessories
21
STAPLE YOUR RECEIPT HERE
Proof of the original purchase
date is needed to obtain
Limited Warranty
TO OBTAIN SERVICE UNDER WARRANTY OR FOR ANY SERVICE RELATED QUESTIONS, please call:
service under warranty
1-888-880-8368
Zephyr Corporation (referred to herein as “we” or “us”) warrants to the original consumer purchaser (referred to herein as “you” or “your”) of Zephyr products (the “Products”) that such Products will be free from defects in materials or work­manship as follows:
Three Year Limited Warranty for Parts: For three years from the date of your original purchase of the Products, we will provide, free of charge, Products or parts to replace those that failed due to manufacturing defects. We may choose, in our sole discretion, to repair or replace parts before we elect to replace the Products.
One Year Limited Warranty for Labor: For one year from the date of your original purchase of the Products, we will provide, free of charge, the labor cost associated with repairing the Products or parts to replace those that failed due to manufacturing defects. After the first year from the date of your original purchase, you are responsible for all labor costs associated with this warranty.
Warranty Exclusions: This warranty covers only repair or replacement, at our option, of defective Products or parts and does not cover any other costs related to the Products including but not limited to: (a) normal maintenance and service required for the Products and consumable parts such as light bulbs, metal and carbon filters and fuses; (b) any Products or parts which have been subject to freight damage, misuse, negligence, accident, faulty installation or installa­tion contrary to recommended installation instructions, improper maintenance or repair (other than by us); (c) commer­cial use of the Products or use otherwise inconsistent with its intended purpose; (d) natural wear of the finish of the Prod­ucts or wear caused by improper maintenance, use of corrosive and abrasive cleaning products, pads, and oven cleaner products; (e) chips, dents or cracks caused by abuse or misuse of the Products; (f) service trips to your home to teach you how to use the Products; or (g) damage to the Products caused by accident, fire, floods or act of God. If you are outside our service area, additional charges may apply for shipping costs for warranty repair at our designated service locations and for the travel cost to have a service technician come to your home to repair, remove or reinstall the Prod­ucts. After the first year from the date of your original purchase, you are also responsible for all labor costs associated with this warranty.
Limitations of Warranty. OUR OBLIGATION TO REPAIR OR REPLACE, AT OUR OPTION, SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. WE SHALL NOT BE LIABLE FOR INCIDENTAL, CONSE­QUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THE PRODUCTS. THE EXPRESS WARRANTIES IN THE PRECEDING SECTION ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES. WE HEREBY DISCLAIM AND EXCLUDE ALL OTHER EXPRESS WARRAN­TIES FOR THE PRODUCTS, AND DISCLAIM AND EXCLUDE ALL WARRANTIES IMPLIED BY LAW, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Some states or provinces do not
allow limitations on the duration of an implied warranty or the exclusion or limitation of incidental or consequential dam­ages, so the above limitations or exclusions may not apply to you. To the extent that applicable law prohibits the exclu­sion of implied warranties, the duration of any applicable implied warranty is limited to the same two-year period described above. Any oral or written description of the Products is for the sole purpose of identifying the Products and shall not be construed as an express warranty. Prior to using, implementing or permitting use of the Products, you shall determine the suitability of the Products for the intended use, and you shall assume all risk and liability whatsoever in connection with such determination. We reserve the right to use functionally equivalent refurbished or reconditioned parts or Products as warranty replacements or as part of warranty service. This warranty is not transferable from the original purchaser and applies in the United States and Canada.
To Obtain Service Under Limited Warranty: To qualify for warranty service, you must: (a) notify us at the address or telephone number stated below within 60 days of the discovery of the defect; (b) give the model number and part identifi­cation number and serial number; and (c) describe the nature of any defect in the Product or part. At the time of the request for warranty service, you must present evidence of your proof of purchase and proof of the original purchase date. If we determine that the warranty exclusions listed above apply or if you fail to provide the necessary documenta­tion to obtain service, you will be responsible for all shipping, travel, labor and other costs related to the services.
Please check our website for any revisions, www.zephyronline.com.
Zephyr Corporation Service Department, 2277 Harbor Bay Parkway, Alameda, CA 94502 1-888-880-8368
MAR11.0201
Genova
ZGE-E30AS ZGE-E36AS ZGE-E30AS290 ZGE-E36AS290
www.zephyronline.com
Guide d’utilisation, d’entretien et d’installation
Numéro de modèle : Numéro de série :
JUL11.0301 © Zephyr Corporation
www.zephyronline.com
MISE EN GARDE DE SÉCURITÉ .......................... 2-3
LISTE DU MATÉRIEL ....................................................... 4
INSTALLATION
Feuille de calcul pour le conduit Espace libre et hauteur de montage Options d’installation pour le conduit Spécifi cations de la hotte Préparation de l’armoire
........................................... 9
........................... 5
................... 6
.................. 7
......................................... 8
Installation de la hotte.................................... 10-12
Reprise d’air sans conduit
....................................... 13
COMMANDES
Commandes à effl eurement
.................................. 14-16
Commande à distance (optionnel) .................. 17
ENTRETIEN
Nettoyage des fi ltres et de la hotte Ampoules
....................................................................... 19
...................... 18
Schéma de câblage....................................... 20
DÉPANNAGE
................................................................................. 21
LISTES DES ACCESSOIRES ET DES PIÈCES
Table des matières
............ 22
LISEZ ET CONSERVEZ CES INSTRUCTIONS
www.zephyronline.com
AVERTISSEMENT
POUR RÉDUIRE LES RISQUES D’INCENDIE OU DE DÉCHARGE ÉLECTRIQUE, N’UTILISEZ PAS CET APPAREIL AVEC UN TABLEAU DE COMMANDE À SEMI-CONDUCTEURS.
AVERTISSEMENT
POUR RÉDUIRE LES RISQUES D’INCENDIE, DE DÉCHARGE ÉLECTRIQUE OU DE BLESSURE, RESPECTEZ CES CONSIGNES :
a. N’utilisez cet appareil que de la manière prévue par le fabricant. Si vous avez des questions, communiquez avec le fabricant. b. Avant de procéder au nettoyage ou à l’entretien de l’appareil, éteignez l’alimentation du panneau électrique et bloquez le dispositif de
déconnexion pour éviter que l’alimentation électrique ne soit accidentellement rallumée. Si le dispositif de sectionnement d’électricité ne peut être bloqué, attachez un avertissement (comme une étiquette) bien en vue sur le tableau électrique.
ATTENTION
Pour ventilation générale seulement. N’utilisez pas cet appareil pour évacuer des vapeurs et des matériaux explosifs ou dangereux. Prenez garde lors de l’utilisation d’agents nettoyants ou de détergents. Ne devrait être utilisé que dans la cuisine de votre maison.
AVERTISSEMENT
POUR RÉDUIRE LES RISQUES DE FEU DE GRAISSE SUR LA SURFACE DE CUISSON :
a. Ne laissez jamais l’appareil sans surveillance lors de son utilisation à haute température. Les débordements par bouillonnement causent de la
fumée et des déversements de graisse qui peuvent prendre feu. Faites chauffer l’huile à des températures basses ou moyennes. b. Allumez toujours la hotte lorsque vous cuisinez à haute température ou que vous faites fl amber des aliments. c. Nettoyez fréquemment les ventilateurs de la hotte. La graisse ne devrait jamais s’accumuler dans les ventilateurs ou les fi ltres. d. Utilisez des poêlons aux dimensions adéquates. Utilisez toujours une batterie de cuisine correspondant aux dimensions de l’élément.
Mise en garde de sécurité
e. Assurez-vous que le ventilateur, les fi ltres et les surfaces où la graisse pourrait s’accumuler sont toujours propres. f. Utilisez le réglage haut de la hotte seulement lorsque nécessaire. g. Ne laissez pas la hotte sans surveillance lorsque vous cuisinez. h. Utilisez toujours une batterie de cuisine et des ustensiles convenant au type et à la quantité de nourriture que vous préparez.
AVERTISSEMENT
POUR RÉDUIRE LES RISQUES DE BLESSURE LORS D’UN INCENDIE SUR LA SURFACE DE CUISSON :
a. ÉTOUFFEZ LES FLAMMES avec un couvercle, une plaque à biscuits ou un plateau de métal et éteignez ensuite le brûleur. PRENEZ GARDE
AUX RISQUES DE BRÛLURE. Si les fl ammes ne disparaissent pas, ÉVACUEZ LES LIEUX ET APPELEZ LE SERVICE D’INCENDIE. b. NE PRENEZ JAMAIS UN POÊLON EN FEU – Vous pourriez vous brûler. c. N’UTILISEZ PAS D’EAU, ou un linge à vaisselle mouillé – une violente explosion de vapeur s’ensuivra. d. Utilisez un extincteur SEULEMENT si :
1. Vous savez que vous possédez un extincteur de classe ABC et vous savez vous en servir.
2. Le feu est faible et ne s’est pas répandu depuis son point d’origine.
3. Vous avez appelé le service d’incendie.
4. Vous pouvez sortir facilement de l’endroit où vous combattez le feu.
AVERTISSEMENT
POUR RÉDUIRE LES RISQUES D’INCENDIE, DE DÉCHARGE ÉLECTRIQUE OU DE BLESSURE, SUIVEZ LES CONSIGNES SUIVANTES :
a. Les travaux d’installation et de câblage électrique doivent être faits par une personne qualifi ée selon les stipulations de tous les normes et
standards en vigueur, dont les normes des constructions ayant une cote de résistance au feu. b. Pour prévenir les contre-explosions, une certaine quantité d’air est nécessaire pour la combustion et l’évacuation des gaz par le carneau
(cheminée) de l’appareil de combustion. Respectez les directives du fabricant d’outillage de chauffage et les normes de sécurité comme celles
publiées par la NFPA (Association nationale des services d’incendie), par la Société américaine des ingénieurs en chauffage, réfrigération et
climatisation (ASHRAE) et par les normes des autorités locales. c. Lorsque vous coupez ou percez un mur ou un plafond, assurez-vous de ne pas endommager le câblage électrique ou toute autre installation
technique dissimulée. d. Les ventilateurs canalisés doivent toujours évacuer l’air à l’extérieur. e. N’installez JAMAIS un interrupteur à une distance atteignable depuis un bain ou une douche. f. Assurez-vous que l’alimentation électrique est éteinte avant de procéder à l’installation, au câblage ou à l’entretien de l’appareil
.
ATTENTION
POUR RÉDUIRE LES RISQUES D’INCENDIE, N’UTILISEZ QUE DES CONDUITS D’AÉRATION EN MÉTAL.
ATTENTION
Pour réduire les risques d’incendie et pour évacuer l’air convenablement, assurez-vous de canaliser l’air à l’extérieur de la maison. N’installez pas l’échappement du conduit dans les espaces entre les murs, le plafond, le grenier, les vides sanitaires ou le garage.
FONCTIONNEMENT
Laissez toujours les grilles de sûreté et les fi ltres en place. Sans ces éléments, les ventilateurs en marche pourraient accrocher des cheveux, des doigts ou des vêtements amples.
Le fabricant se dégage de toute responsabilité dans les cas de non-respect des instructions transmises dans le présent manuel pour l’installation, l’entretien et l’utilisation adéquate du produit. Le fabricant se dégage également de toute responsabilité pour des blessures qui résulteraient de la négligence lors de l’utilisation. De plus, la garantie prend fi n automatiquement lors de l’entretien inapproprié de l’appareil.
*NOTE : Veuillez communiquer avec nous ou visitez le www.zephyronline.com pour obtenir des révisions avant de procéder à des travaux sur commande.
EXIGENCES ÉLECTRIQUES
Important :
Respectez tous les codes et règlements en vigueur. Il est de la responsabilité du client de :
- Communiquer avec un installateur-électricien qualifi é.
- S’assurer que l’installation électrique est adéquate et qu’elle respecte le Code national de l’électricité, la plus récente édition* du ANSI/NFPA 70 ou des normes du CSA C22.1-94, le Code canadien de l’électricité, section 1, la plus récente édition** du code C22.2 No.0-M91 ainsi que tous les codes et réglements en vigueur.
Si les codes permettent l’utilisation d’un fi l de garde isolé et que vous en utilisez un, il est recommandé qu’un électricien qualifi é détermine si le cheminement du fi l est adéquat.
N’effectuez pas la mise à la terre à un tuyau de gaz. Demandez à un électricien qualifi é si vous n’êtes pas certain que la hotte a été mise à la terre adéquatement. N’introduisez aucun fusible dans le circuit neutre ou de mise à la terre. *National Fire Protection Association Batterymarch Park, Quincy, Massachusetts 02269
** CSA International 8501 East Pleasant Valley Road, Cleveland, Ohio 44131-5575 Cet appareil requiert une alimentation électrique de 120V 60Hz. Il doit être connecté à un circuit terminal individuel
dûment mis à la terre, protégé par un disjoncteur de circuit ou un fusible temporisé de 15 ou 20 ampères. Le câblage doit compter 2 fi ls avec mise à la terre. Veuillez vous référer au Diagramme électrique étiqueté sur l’appareil.
Un raccord de câble (non inclus) pourrait également être exigé par les normes et réglementations locales. Informez-vous des exigences et des normes locales. Achetez et installez le connecteur approprié si nécessaire.
ZGE-E30AS, ZGE-E36AS - 370 Watts, 3,1 Ampères ZGE-E30AS290, ZGE-E36AS290 - 167 Watts, 1,4 Ampères
Mise en garde de sécurité
Liste du matériel
www.zephyronline.com
(2) M4 x 1”
Pièces de conduit
3-1/ 4” x 10” rect., droit
Longueur x Nombre utilisé
1 pi x ( ) =
To ta l
Pièces de conduit
pi
6”
embout mural circ./registre
Longueur x Nombre utilisé
30 pi x ( ) =
To ta l
pi
6” circ., droit
7” circ., droit
3-1/ 4” x 10” rect., coude à 90º
3-1/ 4” x 10” rect., coude à 45º
3-1/ 4” x 10” rect., coude plat à 90º
3-1/ 4” x 10”
embout mural rect./registre
3-1/ 4” x 10” rect. à circ. de 6"
1 pi x ( ) =
1 pi x ( ) =
15 pi x ( ) =
9 pi x ( ) =
24 pi x ( ) =
30 pi x ( ) =
5 pi x ( ) =
pi
pi
pi
pi
pi
pi
pi
6” chapeau de toiture circ.
6” circ. à rect. de 3-1/4" x 10"
6” circ. à rect. de 3-1/4" x 10", coude à 90º
7” or 10”
circ., coude à 90º
7” or 10” circ., coude à 45º
7” or 10” embout mural circ./registre
7” or 10”
circ., chapeau de toiture
30 pi x ( ) =
1 pi x ( ) =
16 pi x ( ) =
15 pi x ( ) =
9 pi x ( ) =
30 pi x ( ) =
30 pi x ( ) =
pi
pi
pi
pi
pi
pi
pi
3-1/ 4” x 10” coude à 90º rect. à circ. de 6"
6” circ., coude à 90º
6” circ., coude à 45º
20 pi x ( ) =
15 pi x ( ) =
9 pi x ( ) =
Sous-total - colonne 1=
pi
pi
pi
pi
Longueur maximale du conduit d’aération :
Pour un mouvement d’air convenable, la longueur totale d’un conduit d’aération rectangulaire de 3 1/4" x 10", ou circulaire de 6" ou 7" de diamètre, ne devrait pas compter plus que l’équivalent de 100 pieds.
7” circ. à rect. de 3-1/4" x 10"
7” circ. à rect. de 3-1/4" x 10", coude à 90º
8 pi x ( ) =
23 pi x ( ) =
Sous-total - colonne 2 =
Sous-total - colonne 1 =
Total du conduit =
pi
pi
pi
pi
pi
Installation – Feuille de calcul pour le conduit d’aération
24” min. 32max.
www.zephyronline.com
Il est important d’installer la hotte à la hauteur de montage adéquate. Les hottes installées trop basses pourraient être endommagées par la chaleur en plus de présenter des risques d’incendie plus élevés tandis que les hottes installées trop hautes seront diffi ciles à atteindre et verront leur effi cacité et leur rendement réduits.
Si elles sont disponibles, consultez les exigences de hauteur d’espace libre requise par le fabricant de la cuisinière ainsi que la hauteur recommandée de montage de la hotte au-dessus de la surface de cuisson. Informez-vous toujours des normes et des réglementations locales en vigueur pour toute différence par rapport aux normes du fabricant.
36”
CONDUIT D’AÉRATION
Un conduit circulaire de 6” doit être utilisé pour assurer une circulation d’air maximale.
N’utilisez que des conduits en métal rigide. Les conduits souples pourraient réduire la circulation d’air jusqu’à 50 %.
Utilisez la feuille de calcul pour obtenir la longueur totale du conduit.
Lorsqu’il possible de le faire, diminuez
Installation – Espace libre et hauteur de montage
TOUJOURS le nombre de pièces et de changements de direction. Si un long tronçon de conduit est nécessaire, augmentez le diamètre du conduit de 6” à 7” ou 8”.
Si des changements de direction ou des adaptateurs sont nécessaires, installez-les le plus loin possible de l’ouverture et le plus éloigné possible l’un de l’autre.
La hauteur de montage de la surface de la cuisinière au bas de la hotte ne devrait pas être
inférieure à 24” et supérieure à 32”.
ENDOMMAGEMENT LORS DE LA LIVRAISON/ INSTALLATION :
• Veuillez vous assurer que toutes les pièces de l’appareil ne sont pas endommagées avant l’installation.
• Si l’appareil est endommagé durant la livraison, retournez l’appareil à l’endroit où vous l’avez acheté pour réparation ou remplacement.
• Si l’appareil est endommagé par le client, la réparation ou le remplacement est à la charge du client.
• Si l’appareil est endommagé par l’installateur (si autre que le client), le client et l’installateur doivent en venir à une entente pour la réparation ou le remplacement.
AVERTISSEMENT DE RISQUE D’INCENDIE
N’évacuez ou ne terminez JAMAIS l’échappement du conduit dans les espaces entre les murs, les vides sanitaires, le plafond, le grenier, ou le garage. Tous les échappements doivent être dirigés à l’extérieur de la maison, à moins que l’option de reprise d’air ne soit utilisée.
N’utilisez que des conduits en métal pour cloison simple. Fixez toutes les pièces du conduit avec des vis à tôle et isolez tous les joints avec du ruban adhésif en toile ou
du ruban réfl ecteur certifi é.
Exemples d’options pour le conduit d’aération
Installation – Options pour le conduit d’aération
www.zephyronline.com
LC
Installation – Spécifi cations de la hotte
9/16”
1-
7”
19-7/8”
C/L
Fig.1
7 3/4
9-
7/8”
Fig.2
1. Calculez et marquez la ligne centrale sur le mur et sur le bas de l’armoire avec un crayon.
2. Si le bas de l’armoire est enfoncé, vous devrez installer des blocs de bois pour aligner correctement le bas de l’armoire avec la hotte. Les blocs de bois devraient arriver à ras du bas de l’armoire.
3. Respectez les dimensions de la Fig.1 et coupez le bas de l’armoire pour créer une ouverture permettant l’installation de l’armoire. Si vous avez une armoire sans cadre, calculez la distance de 1-9/16” (mentionné à la Fig.1) à partir de l’avant de la porte de l’armoire. Ainsi, le rebord avant de la hotte arrivera à égalité avec les portes de l’armoire lorsqu’elles seront fermées. Voir Fig.2.
INSTALLATION – Préparation de l’armoire
www.zephyronline.com
1) Préparez le câblage électrique et le conduit dans l’armoire. Les emplacements de la boîte de connexion et l’ouverture de refoulement de ventilateur sont indiqués à la page 8.
Fig.3 Fig.4
2) Dévissez les (10) vis du panneau avant et laissez le panneau de côté, Fig.3. Vous aurez maintenant accès à l’intérieur de la hotte.
3) Ouvrez les portes de l’armoire. Soulevez la hotte et faites-la glisser dans l’ouverture située au bas de l’armoire, Fig.4. Assurez-vous que l’ouverture correspond aux dimensions indiquées à la page 9, Fig.1.
Installation – Installation de la hotte
Fig.5 Fig.6
4) Des attaches à ressort sont situées sur les côtés gauche et droit du boîtier de la hotte. Elles tiendront temporairement la hotte en place, Fig.5.
2
1
5) Fixez les supports supérieurs aux côtés gauche et droit du boîtier de la hotte à l’aide de (2) vis 3/16 x 3/8” par support, Fig.6. Assurez-vous que les (2) trous à vis pour les écrous imperdables pointent vers le bas. Note : Compte tenu de l’espace de travail restreint pour les armoires des hottes de 30”, vous devrez utiliser un tournevis à angle droit ou un tournevis cruciforme de 2”.
10
Fig.7 Fig.8
6) Placez les supports d’installation inférieurs sous les supports d’installation supérieurs situés sur les côtés gauche et droit du boîtier de la hotte, Fig.7. Note : La partie plus large des supports d’installation inférieurs devrait se trouver au bas de la hotte.
2
1
1
7) À partir de l’intérieur de la hotte, fi xez (1) vis M4x8 dans chaque support d’installation inférieur. La position de ces vis est ajustable et s’adapte à différentes épaisseurs de dessous d’armoire, Fig.8. Ne serrez pas complètement les vis pour l’instant.
Fig.9 Fig.10
8) Installez (2) vis 3/16x1” dans les écrous imperdables de chaque support d’installation supérieur. Serrez les vis pour ajuster la hauteur de la hotte jusqu’à ce qu’il n’y ait plus d’espace entre le bas de l’armoire et le rebord avant de la hotte, Fig.9. Une fois que la hotte est en place, serrez complètement les vis des supports d’installation inférieurs de l’étape 7, Fig.8-1.
B
A
9) Un panneau de remplissage est inclus pour composer avec les différentes profondeurs d’armoire. Deux vis de serrage sont situées à l’intérieur de la hotte sur les côtés gauche et droit à l’arrière de la hotte, Fig.10A. Tournez chaque vis de serrages dans le sens des aiguilles d’une montre pour pousser le panneau de remplissage vers le mur, Fig.10B. Serrez les vis de serrage jusqu’à ce que le panneau de remplissage touche au mur et qu’il soit bien fi xé en place. Consultez les spécifi cations de la page 8 pour les profondeurs d’armoire possible.
11
Installation – Installation de la hotte
Fig.11 Fig.12A
10) Placez le conduit circulaire de 6” par-dessus le collier du ventilateur et fi xez le tout avec du ruban à conduit en aluminium. Si vous utilisez la hotte en mode de reprise d’air, allez à la page 13.
Installez le câblage électrique. Note : Un raccord de câble (non inclus) pourrait également être exigé par les normes et réglementations locales. Informez-vous des exigences et des normes locales. Achetez et installez le connecteur approprié si nécessaire.
www.zephyronline.com
A
11) Secure (2) 1 “vis à bois (A) dans les trous de vis sur les côtés gauche et droit de l’ouverture du fi ltre. Ainsi, pourra le corps de la hotte à la base du cabinet et de prévenir le capot de se déplacer après installation.
Assurez-vous qu’aucun matériel d’emballage ne se trouve à l’intérieur de la hotte. Allumez la hotte, assurez-vous qu’il n’y a pas de fuites où il y a du ruban à conduit et assurez-
Installation – Installation de la hotte
vous du bon fonctionnement de toutes les fonctions.
Fig.12B
12) Remettez le panneau avant sur la hotte et fi xez-le en place à l’aide des (10) vis que vous aviez préalablement enlevées à l’étape 2.
12
La confi guration de reprise sans conduit a été conçue pour les applications où il est impossible d’installer un conduit d’aération. Lorsque transformée, la hotte fonctionne comme une hotte de reprise d’air plutôt que comme un système d’évacuation d’air. Les vapeurs et fumées de cuisson sont aspirées et fi ltrées par un ensemble optionnel de fi ltres à charbon. L’air est ensuite purifi é et redirigé à l’intérieur de la maison.
Nous recommandons de TOUJOURS évacuer l’air à l’extérieur de la maison en utilisant le conduit en place ou, s’il y a possibilité, en installant un nouveau conduit. La hotte est plus effi cace lorsqu’utilisée comme système d’évacuation d’air. Vous ne devriez recourir à la confi guration de reprise d’air que lorsqu’il est impossible d’installer un conduit d’aération.
Lorsque la confi guration de reprise d’air est choisie, un fi ltre à charbon doit être installé sur le fi ltre à tamis décoratif. Commandez-les en vous référant au numéro de pièce ci-dessous. Le fi ltre à tamis décoratif est conçu pour capturer les résidus de cuisson et le fi ltre à charbon optionnel aide à la purifi cation des vapeurs et fumées de la cuisson lors de la reprise d’air.
ENSEMBLE DE REPRISE D’AIR (REQUIS SI AUCUN CONDUIT N’EST UTILISÉ)
L’ensemble comprend un fi ltre à charbon et un défl ecteur d’air.
Modèle de hotte Numéro de pièce Filtres par paquet
ZGE (tous les modèles) ZRC-00GE 1
1. Procurez-vous l’ensemble de reprise d’air en utilisant le numéro de pièce ci-dessus
2. Retirez le fi ltre à tamis décoratif de la hotte et placez le fi ltre à charbon au-dessus du fi ltre à tamis. Fixez le fi ltre à charbon au fi ltre à tamis en utilisant les supports à câble fournis, tel qu’illustré sur la Fig. 13.
3. Réinstallez le fi ltre à tamis décoratif.
4. Pour que la reprise d’air se fasse convenablement, un évent de reprise d’air doit être installé pour permettre à l’air recyclé d’être relâché dans la cuisine, Fig. 14. Un conduit doit être installé du ventilateur à l’évent. L’évent de reprise d’air peut être placé sur le dessus de l’armoire, ou dans le plafond ou vide sanitaire.
5. Allumez l’indicateur de changement du fi ltre sur le tableau de commande (voir page 15).
6. Le fi ltre à charbon doit être remplacé après 120 heures d’utilisation (ou approximativement tous les 3-4 mois à raison de 1 heure d’utilisation quotidienne). Le microprocesseur peut être réglé pour calculer le temps d’utilisation et vous indiquerquand changer le fi ltre, toutes les 120 heures d’utilisation.
Installation - Reprise d’air sans conduit
Remplacement du fi ltre à charbon
Modèle de hotte Numéro de pièce Quantité à commander
ZGE (Tous les modèles) Z0F-C0GE 1
FIG.14
13
FIG.13
www.zephyronline.com
Commandes - Commandes à effl eurement
14
15
CommandesIndicateur de changement des fi ltres à charbon
www.zephyronline.com
COMMANDES – Indicateur de nettoyage des fi ltres à tamis métalliques
16
Mise en garde de la Commission fédérale des communications: Dans le but d’assurer une conformité
continue, toute modifi cation apportée sans l’approbation expresse du parti responsable de la conformité pourrait annuler l’autorisation de l’utilisateur de faire fonctionner cet appareil. Cet appareil respecte l’article 15 des réglementations FCC. Le fonctionnement doit respecter les deux réglementations suivantes : (1) cet appareil ne doit pas causer de brouillage nuisible et (2) cet appareil doit pouvoir recevoir tout type d’interférence, dont des interférences qui pourraient causer un fonctionnement involontaire.
La commande à distance est vendue séparément comme accessoire en option. Achetez la pièce Zephyr portant le numéro 14000005
Cette commande à distance peut fonctionner dans un environnement humide, mais pas lorsque laissée sur une surface trempée
SYNCHRONISATION: Pour créer un lien unique entre votre hotte de cuisiniére et de controle à distance s’il vous
plait suivre les êtapes ci-dessous:
1. Avec hotte appuyez et maintenez les “lumiéres” sur la hotte jusqu’à ce que la lettre “F” apparait sur l’êcran.
2. Appuyez sur le “lumiéres” sur la télécommande, les lumiéres sur le capot se mettra en marche. La synchronisation est terminée.
FONCTIONS DE CONTROLE A DISTANCE:
La commande à distance radioélectrique est munie d’un aimant pour un entreposage facile. la commande peut être placé sur n’importe quelle surface magnétique, comme un réfrigérateur ou le support à commande zephyr. la distance maximale de l’appareil à laquelle la commande fonctionne est de 15 pieds.
Commandes – Commande à distance radioélectrique
ENTRETIEN DE LA COMMANDE À DISTANCE:
Nettoyez la commande à distance avec des détergents non abrasifs.
Suivez les instructions ci-dessous pour remplacer la pile.
Enlevez le couvercle du compartiment à pile (A) à l’aide d’un tournevis plat pour avoir accès à la pile.
+
A
-
Enlevez la pile et remplacez-la avec une pile de type A23 12V. L’extrémité négative devrait faire face au ressort à l’intérieur de la commande à distance.
Remettez le couvercle du compartiment en place et recyclez la vieille pile.
17
www.zephyronline.com
ENTRETIEN DES SURFACES
Nettoyez régulièrement les surfaces de la hotte avec de l’eau savonneuse chaude et un chiffon de coton propre. N’utilisez pas de détergent abrasif ou corrosif, de laines d’acier ou de tampons à récurer; ils égratigneront et endommageront les surfaces.
Pour les taches plus tenaces, utilisez du produit dégraissant liquide.
Après le nettoyage, vous pouvez polir les surfaces avec des produits de polissage à acier inoxydable non abrasifs pour redonner de l’éclat et du lustre aux surfaces. Frottez toujours doucement, avec un chiffon de coton propre, et dans le sens du grain.
N’utilisez pas de produits à blanchir au chlore ou d’agents nettoyants « orange ».
Filtres à tamis décoratifs
Le fi ltre à tamis installé par le fabricant a pour fonction de fi ltrer les résidus et la graisse de cuisson. Il ne nécessite aucun remplacement sur une base régulière, mais doit être gardé propre.
Le fi ltre devrait être nettoyé chaque 30 heures d’utilisation ou une fois par mois.
Enlevez-le et nettoyez-le à la main ou au lave-vaisselle avec de l’eau tiède. Vaporisez avec du détergent pour graisse et laissez tremper pour éliminer la saleté accumulée.
Séchez le fi ltre et réinstallez-le avant d’utiliser la hotte.
Remplacement du fi ltre à tamis
Si le fi ltre s’use en raison de son âge ou d’une usage prolongé, remplacez-le avec la pièce portant le numéro suivant :
Modèle de hotte: No de pièce Quantité à commander
Tous les modèles ZGE 50200036 1
Pour enlever le fi ltre à tamis décoratif
Entretien – Nettoyage des fi ltres et de la hotte
1.Poussez sur les poignées à ressort
2.Tirez sur la poignée du fi ltre vers le bas pour enlever le fi ltre
1
2
18
Remplacement des ampoules
Attention : Les ampoules deviennent extrêmement chaudes lorsqu’allumées.
Veuillez NE PAS les toucher avant de les avoir éteintes et laissées refroidir. Le contact avec les ampoules chaudes pourrait causer de sérieuses brûlures.
Assurez-vous que l’alimentation électrique est coupée et que les ampoules ne sont pas chaudes.
Enlevez les ampoules en les dévissant dans le sens contraire des aiguilles d’une montre. Note : les ampoules ne se dévissent pas; après une rotation de 60 degrés, elles s’arrêtent et tombent de la douille.
Lorsqu’il est diffi cile de retirer les ampoules après un usage prolongé, fi xez une ventouse équivalant approximativement au diamètre de l’ampoule ou utilisez des gants en latex et tournez.
Les ampoules de remplacement sont disponibles dans les magasins spécialisés en éclairage. Procurez-vous des ampoules halogènes GU-10 50W (MR16).
Consultez la page 22 du présent guide pour obtenir les numéros de pièces Zephyr.
Entretien – Lumières
19
www.zephyronline.com
Entretien – Schéma de câblage
20
PROCÉDURES DE DÉPANNAGE POUR LA HOTTE GENOVA
Problème Cause Solution
Après l’installation, l’appareil ne fonctionne pas.
Les lumières fonctionnent, mais le moteur ne tourne pas.
L’appareil vibre. 1. Le ventilateur n’est pas bien fi xé en place. 1. Serrez solidement les vis du ventilateur en
Le moteur fonctionne, mais pas les lumières.
La hotte ne fonctionne pas bien.
Le fi ltre en métal vibre.
La commande à distance radioélectrique ne fonctionne pas
1. Le bloc d’alimentation n’est pas allumé 1. Assurez-vous que l’alimentation du disjoncteur et de l’appareil est allumée
2. La ligne électrique et le raccord de câble ne sont
pas correctement branchés
3. Les fi ls électriques du tableau de contrôle et de
commande sont débranchés
4. Les câbles du tableau de commande ne sont
pas assez serrés.
5. Tableau de contrôle/commande défectueux 5. Remplacez le tableau de contrôle/commande
1. Le moteur est défectueux, possiblement bloqué 1. Remplacez le moteur.
2. Le système de protection thermale détecte que
le moteur est trop chaud pour fonctionner et l’éteint.
3. Le condensateur est endommagé. 3. Remplacez le condensateur
4. Le câble du ventilateur n’est pas branché 4. Assurez-vous que le câble du ventilateur est
2. La roue du ventilateur est endommagée. 2. Remplacez le ventilateur.
3. La hotte n’est pas bien fi xée en place. 3. Vérifi ez l’installation de la hotte.
1. L’ampoule halogène est défectueuse. 1. Remplacez l’ampoule halogène.
2. L’ampoule est desserrée. 2. Serrez l’ampoule.
3. 3.Les câbles du tableau de commande ne sont
pas assez serrés.
1. La hotte est possiblement installée trop haut par
rapport à la cuisinière.
2. Du vent provenant d’une fenêtre ou d’une porte
ouverte avoisinante nuit à la ventilation.
3. L’ouverture du conduit ou le conduit lui-même
est bloqué.
4. L’ouverture du conduit est contre le vent. 4. Ajustez l’orientation de l’ouverture du conduit.
5. Mauvaises dimensions de conduit d’aération. 5. Remplacez le conduit par un conduit adéquat.
1. Le fi ltre en métal est desserré. 1. Remplacez le fi ltre en métal.
2. L’attache à ressort ne fonctionne pas
convenablement.
1. La pile est morte 1. Remplacez-la pile à l’aide d’une pile A23 12v.
2. Mauvaise communication avec la hotte. 2. La commande à distance doit se trouver à
3. La commande à distance a perdu la
communication avec la hotte.
2. Vérifi ez que le branchement de l’appareil a été fait correctement.
3. Assurez-vous que les fi ls électriques entre les tableaux de contrôle et de commande sont branchés convenablement
4. Assurez-vous que les câbles du tableau de commande sont branchés convenablement.
2. Le moteur fonctionnera normalement lorsque le système de protection thermale aura refroidi
branché dans le connecteur Molex
place.
3. Assurez-vous que les câbles du tableau de commande sont branchés convenablement.
1. Ajustez la distance entre la surface de la cuisinière et la base de la hotte entre 24” et 32”.
2. Fermez toutes les portes et fenêtres pour éliminer les courants d’air.
3. Enlevez tout ce qui bloque l’ouverture ou le conduit d’aération.
2. Ajustez la poignée jusqu’à ce que l’attache à ressort fonctionne.
moins de 15 pi de la hotte.
3. Réinitialisez la hotte et la commande à distance en coupant le courant du disjoncteur pendant 5 minutes. Placez la commande à distance sur le comptoir près de la hotte et remettez le disjoncteur sous tension.
DÉPANNAGE
21
www.zephyronline.com
DESCRIPTION NO DE PIÈCE
Pièces de remplacement
Ampoule GU10 50W (chaque) Z0B-0020S Filtre à tamis décoratif 50200036
Accessoires optionnels
Ensemble de reprise d’air ZRC-00GE Filtres à charbon de remplacement (chaque) Z0F-C0GE Commande à distance radioélectrique 14000005
Pour commander des pièces, visitez-nous en ligne au www.zephyronline.com ou communiquez avec nous par téléphone au 1-888-880-8368
Listes des pièces et des accessoires
22
AGRAFEZ VOTRE REÇU ICI
Une preuve de la date d’achat originale
Garantie limitée
POUR OBTENIR DU SERVICE SOUS GARANTIE OU POUR TOUTE QUESTION LIÉE À L’ENTRETIEN,
veuillez communiquer avec nous au 1-888-880-8368
Zephyr Corporation (désigné aux présentes sous le nom de « nous ») garantit au premier acheteur (désigné aux présen­tes sous le nom de « vous » ou « votre ») de produits Zephyr (les « Produits ») que lesdits produits sont exempts de défauts de fabrication ou de main-d’œuvre selon les conditions suivantes :
Garantie de trois ans sur les pièces : Garantie de trois ans à partir de la date d’achat originale du Produit. Nous fournirons sans frais les Produits ou les pièces de remplacement qui comportaient des défauts de fabrication. Nous pourrions choisir, à notre seule discrétion, de réparer ou de remplacer des pièces avant de prendre la décision de rem­placer le Produit.
Garantie limitée d’un an sur la main-d’œuvre : Garantie d’un an à partir de la date d’achat originale du Produit. Nous couvrirons sans frais les frais de main-d’œuvre afférents à la réparation du Produit ou des pièces de remplacement qui comportaient des défauts de fabrication. Un an après la date d’achat originale, vous serez responsable de tous les frais de main-d’œuvre associés à la présente garantie.
Exclusions de la garantie : Cette garantie ne couvre que la réparation ou le remplacement, à notre gré, de pièces ou de Produits défectueux et ne couvre aucun autre coût afférent aux Produits, dont, sans s’y limiter, les frais liés : (a) à l’entretien normal des Produits et au remplacement des pièces consommables, comme les ampoules, les filtres métal­liques, les filtres à charbon et les fusibles; (b) à tout Produit ou pièce ayant été endommagé durant le transport ou étant le résultat d’un mauvais usage, d’une négligence, d’un accident, d’une installation incorrecte ou ne respectant pas les notices d’installation recommandées, d’un entretien ou d’une réparation inapproprié (dont ne nous sommes pas respon­sables); (c) à une utilisation commerciale ou ne correspondant pas à l’utilisation pour laquelle les Produits sont conçus; (d) à l’usure naturelle du fini, à l’usure due à un entretien inadéquat, à l’utilisation de produits nettoyants corrosifs ou abrasifs, de tampons nettoyeurs et de produits de nettoyage pour le four; (e) aux éclats, entailles ou fissures résultant d’un abus ou d’une mauvaise utilisation du Produit; (f) aux déplacement d’un technicien de service à votre domicile pour vous montrer comment utiliser les Produits; (g) aux dommages causés par un accident, un incendie, une inondation ou un cas fortuit. Si vous vous trouvez à l’extérieur du territoire que nous desservons, des frais supplémentaires pourraient s’appliquer pour la livraison des produits à nos points de service désignés pour une réparation sous garantie ou vous pourriez avoir à débourser les frais de déplacement du technicien à votre domicile pour que le Produit soit réparé, enlevé ou réinstallé. Un an après la date d’achat originale du Produit, vous êtes également responsable de tous les frais de main-d’œuvre associés à la présente garantie.
est nécessaire pour obtenir du service
lorsque le produit est sous garantie
Restrictions de la garantie. NOTRE OBLIGATION DE RÉPARER OU DE REMPLACER, À NOTRE GRÉ, LE PRODUIT CONSTITUE VOTRE SEUL ET UNIQUE RECOURS SOUS LA PRÉSENTE GARANTIE. NOUS NE NOUS PORTONS PAS RESPONSABLES POUR TOUT DOMMAGE INDIRECT, ACCESSOIRE OU PARTICULIER RÉSULTANT OU AYANT UN LIEN AVEC L’UTILISATION OU LE RENDEMENT DES PRODUITS. LES GARANTIES EXPRESSES DE LA SEC­TION PRÉCÉDENTE SONT EXCLUSIVES ET TIENNENT LIEU DE TOUTE AUTRE GARANTIE EXPRESSE. PAR LES PRÉSENTES, NOUS REJETONS ET EXCLUONS TOUTE AUTRE GARANTIE EXPRESSE POUR LES PRODUITS ET TOUTES LES GARANTIES TACITES PRÉVUES PAR LA LOI, DONT CELLES RELATIVES À LA QUALITÉ MARCHANDE OU À L'ADÉQUATION DU PRODUIT POUR UNE UTILISATION PARTICULIÈRE. Certains États ou
provinces n’autorisent pas les restrictions sur la durée d’une garantie implicite ou l’exclusion ou la restriction des dom­mages indirects ou accessoires; par conséquent, les exclusions et restrictions mentionnées ci-dessus pourraient ne pas s’appliquer à votre cas. Dans la mesure où une loi applicable interdit l’exclusion de garanties implicites, la durée de toute garantie implicite applicable se limite à la période de deux ans décrite ci-dessus. L’unique objectif de toute descrip­tion orale ou écrite est de présenter les Produits et celle-ci ne devrait pas être interprétée comme une garantie expresse. Avant d’utiliser ou de permettre l’utilisation des Produits, vous devrez déterminer si les Produits conviennent aux utilisa­tions prévues et vous devrez assumer tout risque et toute responsabilité relatifs à ces utilisations. Nous nous réservons le droit d’utiliser des pièces reconstruites ou remises à neuf pour remplacer l’une des fonctionnalités dans le cadre de la présente garantie ou de l’une des parties de la présente garantie. L’acheteur original ne peut transférer la présente garantie et celle-ci n’est valide qu’aux États-Unis et au Canada.
Pour obtenir du service sous la garantie : Pour avoir droit à du service sous garantie, vous devez : (a) nous avertir en utilisant l’adresse ou le numéro de téléphone inscrit ci-dessous dans les soixante jours suivant la détection du défaut; (b) donner le numéro du modèle, le numéro d’identification de la pièce ainsi que le numéro de série; et (c) décrire la nature de tout défaut de la pièce ou du Produit. Au moment de faire la demande de service sous garantie, vous devrez présenter votre preuve d’achat et la preuve de la date d’achat originale. Si nous déterminons que les exclusions de la garantie énumérées ci-dessus s’appliquent ou si vous vous trouvez dans l’incapacité de nous fournir la documentation nécessaire pour obtenir du service, vous serez responsable de tous les frais d’expédition, de déplacement, de main-d’œuvre ou de tout autre coût afférent au service.
Veuillez consulter notre site Web au www.zephyronline.com pour savoir si des révisions ont été apportées à la garantie.
Zephyr Corporation Service Department, 2277 Harbor Bay Parkway, Alameda, CA 94502 1-888-880-8368
MAR11.0201
Loading...