www.atlona.com | toll free: 1-877-536-3976or International: 1-408-962-0515
User Manual
SoloCAT™ HD
HDMI 1.4 OVER SINGLE CAT5/6/7 EXTENDER
WITH BI-DIRECTIONAL IR and
RS232 TRANSMITTER & RECEIVER
.atlona.com | toll free: 1-877-536-3 International: 1-408-962-0515
TABLE OF CONTENTSINTRODUCTION:
Included items
• SoloCAT™ HD HDMI Transmitter x 1
• SoloCAT™ HD HDMI Receiver x 1
• Zektor Gripper™ HDMI cable securing support brackets x2
• 15V Switching Power Supply x 1
• User’s Manual x 1
About the SoloCAT HD™
The SoloCAT™ HD HDMI over CAT5e/6 Extender kit is designed to be HDMI 1.4a compatible
and 3D capable, enabling the reliable transmission of the HDMI; bi directional IR and bi
directional RS232 signals up to 330ft in 1080p HD (even 2k/4k resolutions and 3D format).
Because the SoloCAT™ HD is HDMI 1.4 compatible it allows you to take full advantage of the
new technology by supporting much higher resolutions than 1080p or 1440p including 2k
(2048x1080p) and 4k (4096×3072) resolutions. Future versions of this device will add the
capability for Ethernet data channel, allowing other HDMI 1.4 enabled devices to share a
network connection for internet connectivity. Additionally for future versions, the audio return
channel which will send the audio signal back from the display to a receiver or other audio
device.
Since the SoloCAT™ HD has bi-directional IR, it is the perfect device for multi-room applications
and third party control systems. With bi-directional communication from a remote control or
control system, commands can be sent from the remote location back to the main equipment
center or the other way around. Note: The maximum usable distance depends on the quality
and characteristics of the cables. Higher resolutions and longer transmission distances work
better with low skew cables (<25ns/100m) for the best performance. Unshielded Cat5e/6 with
metal RJ-45 connectors and 568-B termination will provide best results.
For more information about HDMI over HDBaseT technology you can visit www.valenssemi.com.www.atlona.com | toll free: 1-877-536-36
For International: 1-408-962-0515
Safety and Notice
The Zektor Incorporated SoloCAT™ HD HDMI™ over single CAT5e/6 extender has been tested
for conformity to safety regulations and requirements, and has been certified for international
use. However, like all electronic equipments, the Zektor Incorporated SoloCAT™ should be
used with care. Please read and follow the safety instructions to protect yourself from possible
injury and to minimize the risk of damage to the unit.
Follow all instructions and warnings marked on this unit
Do not attempt to service this unit yourself, except where explained in this manual
Provide proper ventilation and air circulation
Do not use near water
Keep objects that might damage the device and assure that the placement of this unit is on
a stable surface
Use only the power adapter and power cords and connection cables designed for this unit
Do not use liquid or aerosol cleaners to clean this unit
Always unplug the power to the device before cleaning
Specifications
HDMI compliant to v1.4
3D capable
HDMI Connector 19 pin type female connector
HDMI Source Input Port 1
HDMI Sink Output Port 1
Source Port Connector Standard 19 pin HDMI
Display Device Port Connector Standard 19 pin HDMI
Link Connector RJ-45 Shielded
HDCP Compliant
Power on LED Indicator
Input TMDS signal 1.2 volts (peak-to-peak)
Input DDC signal 5 volts (peak-to-peak)
Uncompressed video resolution 1080p / 1920x1200 / 2k (2048x1080p) and 4k (4096×3072)
Deep Color 24-48 bits
Video Bandwidth Up to 10.2GHz
Vertical Frequency Range 50 ~60 Hz
Audio Performance PCM (7.1ch), Dolby Digital, True HD, DTS-HD & Master Audio
Power Consumption (max.) 15 Watts
Operation Temperature 0°C to 70°C.
Power Supply 5V 2A (universal)
Zektor Gripper™ HDMI cable support brackets
Dimension (in) 6 x 5 x 1
Weight (lb) 2.3
Supports Refresh Rates: 24Hz, 30Hz, 60Hz
Supports Bi-directional IR transmission (38Khz only)
LED indicators for operation modes
Supports transmission distances up to 328ft @ 1080p 50/60Hz
Easy to install, simple to operate and the most effective solution for long signal extension.
HDMI over HDBaseT is the cost effective way to reliably transmit long distance HDMI for
commercial, residential, digital signage applications over a single CAT5e/6 cable.
SPECIFICATIONS:
SoloCAT™ HD transmitter front panel
1. RS-232 Jack 5. HDMI Output
2. DC 5V Power Jack 6. IR Receiver
3. RJ45 Jack 7. IR Transmitter
4. HDMI Input (local loop)
1. IR Eye
2. HDCP Indicator
3. Activity Indicator
4. Power Indicator
SoloCAT™ HD receiver rear panel
1. RS-232 Jack
2. DC 5V Power Jack
3. RJ45 Jack
4. HDMI Output
5. IR Transmitter
6. IR Receiver
RS-232 WIRING DIAGRAM
!! Important Power on Sequence and Connections!!
For best results, apply power to one side of the SoloCAT HD BEFORE connecting the CAT
cable. In some cases, connecting the CAT cable before applying power can cause difficulty in
sinking devices.
Installation
1. Connect your HDMI source to the transmitter.
2. Connect your HDMI Display to the receiver.
3. Plug in the DC power adapter to the power jack of the transmitter or the receiver. Zektor has
utilized the proprietary power supply design from our component SoloCAT™ family. This allows
you to power from the transmitter or the receiver, whichever is the most convenient.
4. Use CAT5e/6 cables to link the transmitter and the receiver. As in all installations, poor
quality cable will result in lesser quality results and occasionally intermittent problems. However,
in our testing we used off the shelf CAT5e cable from Home Depot® which worked fine and
provided an outstanding result. Zektor recommends using EIA/TIA 568B for CAT5e/6
termination. We have included a reference diagram below for your convenience.
5. Make sure that the source, the transmitter, the receiver and the displays are all properly
connected. Zektor has designed and manufactured a new HDMI cable support bracket, the
Zektor Gripper™, to help ensure that your HDMI cable remains properly connected to our
transmit / receive pair.
6. Connect your serial cables if using the bi directional serial function.
7. Properly install your IR blaster and sender. Incorrect installation can damage your
SoloCAT™ extender pair. If TX/RX (transmit & receive) are mistakenly connected in the wrong
connections, the IR eye can get damaged. 3rd party IR emitters/blasters, must be able to handle
up to 60 KHz 1-
8. After initial power on, allow for EDID verification and HDCP handshake. A visible image at
the display after initial power on can take up to 5 seconds.
DIP switch information
All dip switches are set in the UP position. DO NOT CHANGE DIP SWITCH SETTING POSITIONS.
Currently these are all reserved, and were put there for options they might exist in future versions of the
chipset. Currently there are no options and it is likely the access opening in the chassis will be removed
for the DIP switch
Bi directional IR
: The inputs are optically isolated, so it doesn't make any difference in how you connect to it. They will
accept an input signal of between 3 and 12 volts. Each time the input has power across it, the output will
go high. The output will drive an LED flasher that is wired like:
RING
|
|
/ \
/___\
|
|
TIP
In our initial production run we adopted the pinout wiring that is utilized by Control4. We have discovered
that this is the opposite wiring that is more commonly used. Production units shipped after February 1,
2012 will utilize a more widely used standard IR communication.
For all units shipped prior to January 15, 2012: the IR channels can be thought of as an extension of
an IR flasher. If you connect the input of the SoloCAT HD™ to an output of an IR control, and then
connect the output to a flasher LED, it will flash the LED. Though the LED's cable may have to but cut
and inverted (the two wires going to the LED may need to be crossed and reconnected) before the LED
will flash.
LED Indicators
On the front of the SoloCAT HD™ chassis there is a vertical block of four (4) green LED’s that is marked
“Status” on the chassis just above the LED’s. From top to bottom this is an explanation of their activity:
1. #1 LED indicates normal operations and will flash 1 a second.
2. #2 LED down indicates a valid link between the transmitter and receiver.
3. #3 LED indicates a valid HDCP link, and is steady in normal use and flashing while it's trying to
connect, or there's an error in connecting.
4. #4 LED on the bottom one is currently reserved.
EIA/TIA-568-B termination is highly recommended for best results
REGISTRATION
EZ Crimp RJ45 crimp connectors:
Zektor is conducting long term testing on these popular connectors. HDBaseT
does not appear to be as susceptible to interference as other technologies. To
eliminate any potential functional problems, standard crimp RJ45 connectors
should be used.
Troubleshooting
Problem: No picture
Action: Make sure your source is working properly and outputting video. Check all
connections from the source and control ports to the transmitter and from the receiver to
the display and control ports. Make sure you have activity lights on the SoloCAT
transmitter and receiver. If no lights, remove all connections including power.
Reconnect serial and/or IR if used, and power. Reconnect CAT cable. Within 1-2 seconds
you should see activity lights on the transmitter and receiver. Within 2-3 seconds you
should have a picture on your display.
Action: Verify your cable is no longer than 328’. Make sure termination is identical on
both ends. Verify your cable is not pinched, cut or has a defect. It is always good to
have a good, known working cable available to verify.
Problem: IR/RS232 not communicating
Action: Make sure all DIP switches are in the furthest upright position. Double check all
connections. IR and RS232 activity is immediate and requires no delay or sync time.
Problem: No power
Action: Check for power at electrical source. Remove and reconnect to one side of the
SoloCAT HD. Only use DC wall power supplies provided by Zektor. If problem
persists, call Zektor tech support and request a replacement power supply.
Problem: Intermittent picture, pixilation
Action: Check all cabling. This is the most action to resolve issues. If you are using
EZ Crimp RJ45 connectors make sure the end of the cable is not corroded and/or
shorting out. Re-terminate to T568B on both ends with standard crimp RJ45
connectors. Check all HDMI connections.
Remove all power. Apply power and connections as described in the installation
section.
Limited Warranty
-
Zektor Incorporated (“Zektor”) warrants the SoloCAT™ HD extender to be free from defects in
the material and workmanship for 2 years from the date of purchase from the Zektor or an
authorized dealer. Should this product fail to be in good working order within the 2 year warranty
period, Zektor, at its option, repair or replace the unit, provided that the unit has not been
subjected to accident, disaster, abuse or any unauthorized modifications including static
discharge and power surge. This warranty is offered by Zektor for its BUYER with direct
transaction only. This warranty is void if the warranty seal on the metal housing is broken.
A unit that fails under conditions other than those covered will be repaired at the current price of
parts and labor in effect at the time of repair. Such repairs are warranted for 90 days from the
day of reshipment to the BUYER. If the unit is delivered by mail, customer agrees to insure the
unit or assume the risk of loss or damage in transit. Under no circumstances will a unit be
accepted without a return authorization number.
The warranty is in lieu of all other warranties expressed or implied, including without limitations,
any other implied warranty or fitness or merchantability for any particular purpose, all of which
are expressly disclaimed.
Product must not be physically damaged or chassis opened. All original parts must be returned
to Zektor unless instructed otherwise. Any product that shows signs of abuse or extreme wear
will not be warranted. All products must be returned in reasonable condition.
The content of this manual has been carefully checked and is believed to be accurate. However,
Zektor assumes no responsibility for any inaccuracies that may be contained in this manual.
Zektor will NOT be liable for direct, indirect, incidental, special, or consequential damages
resulting from any defect or omission in this manual, even if advised of the possibility of such
damages. Also, the technical information contained herein regarding the Zektor Incorporated
SoloCAT™ features and specifications is subject to change without further notice.
NO LIABILITY FOR DAMAGES
IN NO EVENT SHALL ZEKTOR INCORPORATED OR ITS SUPPLIERS BE LIABLE FOR ANY
DAMAGES INCLUDING, BUT NOT LIMITED TO, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR
INDIRECT DAMAGES FOR PERSONAL INJURY, LOSS OF BUSINESS PROFITS, BUSINESS
INTERRUPTION, LOSS OF BUSINESS INFORMATION, OR ANY OTHER PECUNIARY LOSS)
ARISING OUT OF THE USE OF OR INABILITY TO USE THIS PRODUCT, EVEN IF ZEKTOR
INCORPORATED HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. ZEKTOR
INCORPORATED AND ITS SUPPLIERS’ ENTIRE LIABILITY UNDER ANY PROVISION OF THIS
AGREEMENT SHALL BE LIMITED TO THE AMOUNT ACTUALLY PAID BY YOU FOR THE PRODUCT.
SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR
CONSEQUENTIAL OR INCIDENTAL DAMAGES; THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
Loading...