Zebra Technologies MC930B User Manual

MC93XX

CAUTION- CLASS 2 LASER LIGHT WHEN OPEN. DO NOT STARE INTO THE BEAM.
ATTENTION-LUMIÉRE LASER DE CLASSE 2 EN CAS D'OUVERTURE. NE PAS REGARDER
DANS LE FAISCEAU. VORSICHT- LASERLICHT KLASSE 2 WENN ABDECKUNG GEÖFFNET.
NICHT IN DEN STRAHL BLICKEN. COMPLIES WITH 21CFR1040.10 & 1040.11 EXCEPT
FOR DEVIATIONS PURSUANT TO LASER NOTICE NO. 50, DATED JUNE 24, 2007 AND
IEC/EN 60825-1:2014.

◰

ݹ䗀ሴⴤ㿶ݹ ᶏ 2 ㊫◰ݹӗ ૱

LASER LIGHT - DO NOT STARE INTO BEAM. CLASS 2 LASER PRODUCT.
LASERLICHT - NICHT IN DEN STRAHL BLICKEN. LASER KLASSE 2. LUMIÉRE
LASER - NE PAS REGARDER DANS LE FAISCEAU. APPAREIL À LASER DE

CLASSE 2. 630-680nm, 1mW

⌘᜿˖ᢃᔰᰦ৺㚄䬱ཡ᭸ᰦᴹ㊫◰ݹ䗀ሴⴤ㿶ݹᶏ

Regulatory Guide

Get Info

MN-003409-01 Rev. A 3/2019Printed in China

Zebra Technologies | 3 Overlook Point | Lincolnshire, IL 60069 USA
www.zebra.com

©2019 ZIH Corp and/or its affiliates. All rights reserved. ZEBRA and the stylized Zebra head are trademarks
of ZIH Corp, registered in many jurisdictions worldwide. All other trademarks are the property of their
respective owners.

Zebra reserves the right to make changes to any product to improve reliability,
function, or design. Zebra does not assume any product liability arising out of, or
in connection with, the application or use of any product, circuit, or application
described herein. No license is granted, either expressly or by implication,
estoppel, or otherwise under any patent right or patent, covering or relating to any
combination, system, apparatus, machine, material, method, or process in which
Zebra products might be used. An implied license exists only for equipment,
circuits, and subsystems contained in Zebra products.

Additional Information

For information on using the MC93XX, refer to the MC93XX User Guide available at:

zebra.com/mc93xx-info

.

Regulatory Information

This device is approved under Zebra Technologies Corporation.
This guide applies to the following Model Numbers: MC930B, MC930P.
All Zebra devices are designed to be compliant with the rules and regulations in

locations they are sold and will be labeled as required.
Local language translations are available at the following website: www.zebra.com/

support.

Any changes or modifications to Zebra equipment, not expressly approved by Zebra,
could void the user’s authority to operate the equipment.

Declared maximum operating temperature: 50°C.

Bluetooth® Wireless Technology

This is an approved Bluetooth® product. For more information or to view the End
Product Listing, please visit www.bluetooth.org/tpg/listings.cfm

.

Wireless Device Country Approvals

Regulatory markings subject to certification are applied to the device signifying the
radio(s) is/are approved for use in the following countries and continents: United
States, Canada, Japan, China, South Korea, Australia, and Europe.

Please refer to the Declaration of Conformity (DoC) for details of other country
markings. This is available at: www.zebra.com/doc

Note: Europe includes Austria, Belgium, Bulgaria, Croatia, Czech Republic, Cyprus,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Romania, Slovak Republic, Slovenia, Spain, Sweden, Switzerland,
and the United Kingdom.

CAUTION: Operation of the device without regulatory approval is illegal.

Country Roaming

This device incorporates the International Roaming feature (IEEE802.11d), which will
ensure the product operates on the correct channels for the particular country of use.

Ad-Hoc Operation (2.4 GHz Band)

Ad-Hoc operation is limited to Channels 1-11 (2,412-2,462 MHz).

Wi-Fi Direct

Operation is limited to the following channels/bands as supported in the country of
use:

• Channels 1 - 11 (2,412 - 2,462 MHz)

• Channels 36 - 48 (5,150 - 5,250 MHz)

• Channels 149 - 165 (5,745 - 5,825 MHz)

Frequency of Operation – FCC and IC

5 GHz Only

Industry Canada Statement

CAUTION: The device for the band 5,150 - 5,250 MHz is only for indoor usage to reduce

potential for harmful interference to co-Channel mobile satellite systems. High power radars
are allocated as primary users (meaning they have priority) of 5,250 - 5,350 MHz and 5,650

- 5,850 MHz and these radars could cause interference and/or damage to LE-LAN devices.

AVERTISSEMENT: Le dispositive fonctionnant dans la bande 5,150 - 5,250 MHz est réservé

uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage
préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux. Les utilisateurs
de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu'ils ont la
priorité) pour les bands 5,250 - 5,350 MHz et 5,650 - 5,850 MHz et que ces radars pourraient
causer du brouillage et/ou des dommages aux dispositifs LAN-EL.

2.4 GHz Only

The available channels for 802.11 operation in Canada and the US are Channels 1 to

11. The range of channels is limited by firmware.

Health and Safety Recommendations Technology Research.

Ergonomic Recommendations

CAUTION: In order to avoid or minimize the potential risk of ergonomic injury follow the

recommendations below. Consult with your local Health & Safety Manager to ensure that you
are adhering to your company's safety programs to prevent employee injury.

• Reduce or eliminate repetitive motion

• Maintain a natural position

• Reduce or eliminate excessive force

• Keep objects that are used frequently within easy reach

• Perform tasks at correct heights

• Reduce or eliminate vibration

• Reduce or eliminate direct pressure

.

• Provide adjustable workstations

• Provide adequate clearance

• Provide a suitable working environment

• Improve work procedures.

Vehicle Installation

RF signals may affect improperly installed or inadequately shielded electronic
systems in motor vehicles (including safety systems). Check with the manufacturer or
its representative regarding your vehicle. You should also consult the manufacturer
about any equipment that has been added to your vehicle.

An air bag inflates with great force. DO NOT place objects, including either installed or
portable wireless equipment, in the area over the air bag or in the air bag deployment
area. If in-vehicle wireless equipment is improperly installed and the air bag inflates,
serious injury could result.

Position the device within easy reach. Be able to access the device without removing
your eyes from the road.

NOTE: Connection to an alert device that will cause a vehicle horn to sound or

lights to flash on receipt of a call on public roads is not permitted.

IMPORTANT: Before installing or using, check state and local laws regarding

windshield mounting and use of equipment.

For Safe Installation

• Do not put your phone in a location that obstructs the drivers vision or interferes
with the operation of the Vehicle.

• Do not cover an airbag.

Safety on the Road

Do not take notes or use the device while driving. Jotting down a “to do” list or flipping
through your address book takes attention away from your primary responsibility,
driving safely.

When driving a car, driving is your first responsibility - Give full attention to driving.
Check the laws and regulations on the use of wireless devices in the areas where you
drive. Always obey them.

When using a wireless device behind the wheel of a car, practice good common
sense and remember the following tips:

1. Get to know your wireless device and any features such as speed dial and redial.

If available, these features help you to place your call without taking your attention
off the road.

2. When available, use a hands free device.

3. Let the person you are speaking with know you are driving; if necessary, suspend

the call in heavy traffic or hazardous weather conditions. Rain, sleet, snow, ice,
and even heavy traffic can be hazardous.

4. Dial sensibly and assess the traffic; if possible, place calls when you are not

moving or before pulling into traffic. Try to plan calls when your car will be
stationary. If you need to make a call while moving, dial only a few numbers,
check the road and your mirrors, then continue.

5. Do not engage in stressful or emotional conversations that may be distracting.

Make people you are talking with aware you are driving and suspend
conversations that have the potential to divert your attention from the road.

6. Use your wireless phone to call for help. Dial the Emergency services, (9-1-1 in

the US, and 1-1-2 in Europe) or other local emergency number in the case of fire,
traffic accident or medical emergencies. Remember, it is a free call on your
wireless phone! The call can be made regardless of any security codes and
depending on a network, with or without a SIM card inserted.

7. Use your wireless phone to help others in emergencies. If you see an auto

accident, crime in progress or other serious emergency where lives are in danger,
call the Emergency Services, (9-1-1 in the US, and 1-1-2 in Europe) or other local
emergency number, as you would want others to do for you.

8. Call roadside assistance or a special non-emergency wireless assistance number

when necessary. If you see a broken-down vehicle posing no serious hazard, a
broken traffic signal, a minor traffic accident where no one appears injured, or a
vehicle you know to be stolen, call roadside assistance or other special non­emergency wireless number.

“The wireless industry reminds you to use your device / phone safely when driving”.

Warnings for Use of Wireless Devices

CAUTION: Please observe all warning notices with regard to the usage of wireless devices.

Potentially Hazardous Atmospheres – Vehicles Use

You are reminded of the need to observe restrictions on the use of radio devices in
fuel depots, chemical plants etc. and areas where the air contains chemicals or
particles (such as grain, dust, or metal powders) and any other area where you would
normally be advised to turn off your vehicle engine.

Safety in Aircraft

Switch off your wireless device whenever you are instructed to do so by airport or
airline staff. If your device offers a ‘flight mode’ or similar feature, consult airline staff
as to its use in flight.

Safety in Hospitals

Wireless devices transmit radio frequency energy and may affect medical electrical
equipment.

Wireless devices should be switched off wherever you are requested to do so in
hospitals, clinics or healthcare facilities. These requests are designed to prevent
possible interference with sensitive medical equipment.

Pacemakers

Pacemaker manufacturers recommended that a minimum of 15 cm (6 inches) be
maintained between a handheld wireless device and a pacemaker to avoid potential
interference with the pacemaker. These recommendations are consistent with
independent research and recommendations by Wireless Technology Research.

Persons with Pacemakers:

• Should ALWAYS keep the device more than 15 cm (6 inches) from their
pacemaker when turned ON.

• Should not carry the device in a breast pocket.

• Should use the ear furthest from the pacemaker to minimize the potential for
interference.

• If you have any reason to suspect that interference is taking place, turn OFF your
device.

Other Medical Devices

Please consult your physician or the manufacturer of the medical device, to determine
if the operation of your wireless product may interfere with the medical device.

RF Exposure Guidelines

Safety Information

Reducing RF Exposure – Use Properly

Only operate the device in accordance with the instructions supplied.

International

The device complies with internationally recognized standards covering human
exposure to electromagnetic fields from radio devices. For information on
'International' human exposure to electromagnetic fields, refer to the Zebra
Declaration of Conformity (DoC) at www.zebra.com/doc

For further information on the safety of RF energy from wireless devices, see

www.zebra.com/responsibility

located under Corporate Responsibility.

.

Europe

This device was tested for typical body-worn operation. Use only Zebra tested and
approved belt-clips, holsters, and similar accessories to ensure EU Compliance.

US and Canada

Co-located statement

To comply with FCC RF exposure compliance requirement, the antenna used for this
transmitter must not be co-located or operating in conjunction with any other
transmitter/antenna except those already approved in this filling.

Use only Zebra tested and approved belt clips, holsters, and similar accessories to
ensure FCC Compliance. The use of third-party belt clips, holsters, and similar
accessories may not comply with FCC RF exposure compliance requirements and
should be avoided. The FCC has granted an Equipment Authorization for these model
phones with all reported SAR levels evaluated as in compliance with the FCC RF
emission guidelines. SAR information on these model phones is on file with the FCC
and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid.

Handheld Devices

This device was tested for typical body worn operation. Use only Zebra tested and
approved belt-clips, holsters, and similar accessories to ensure FCC Compliance.
The use of third-party belt clips, holsters, and similar accessories may not comply with
FCC RF exposure compliance requirements, and should be avoided.

To satisfy US and Canadian RF exposure requirements, a transmitting device must
operate with a minimum separation distance of 1.5 cm or more from a person's body.

Pour satisfaire aux exigences Américaines et Canadiennes d'exposition aux radio
fréquences, un dispositif de transmission doit fonctionner avec une distance de
séparation minimale de 1.5 cm ou plus de corps d'une personne.

Laser Devices

Class 2 laser scanners use a low power, visible light diode. As with any very bright
light source such as the sun, the user should avoid staring directly into the light beam.
Momentary exposure to a Class 2 laser is not known to be harmful.

CAUTION:

specified herein may result in hazardous laser light exposure.

Use of controls, adjustments, or the performance of procedures other than those

Scanner Labeling

Labels Read:

1. LASER LIGHT – DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT.

2. CAUTION - CLASS 2 LASER LIGHT WHEN OPEN. DO NOT STARE INTO
THE BEAM.

3. COMPLIES WITH 221CFR1040.10 AND 1040.11 EXCEPT FOR DEVIATIONS
PURSUANT TO LASER NOTICE NO. 50, DATED JUNE 24, 2007 AND IEC/EN
60825-1:2014.

LED Devices

Classified as ‘EXEMPT RISK GROUP’ according to IEC 62471:2006 and EN
62471:2008.

Pulse duration: 1.7ms for MC93XX Mobile Computer with SE4750.
Pulse duration: Continuous Wave for MC93XX Mobile Computer with SE4850.

Power Supply

Use ONLY a Zebra approved UL LISTED ITE (IEC/EN 60950-1, LPS/SELV) power
supply with electrical ratings: Output 5.4 VDC, min 1.8 A, with a maximum ambient
temperature of at least 50°C. Use of alternative power supply will invalidate any
approvals given to this unit and may be dangerous.

Batteries

Taiwan - Recycling

EPA (Environmental Protection Administration)
requires dry battery producing or importing firms in
accordance with Article 15 of the Waste Disposal
Act are required to indicate the recycling marks on
the batteries used in sales, giveaway or promotion.
Contact a qualified Taiwanese recycler for proper
battery disposal.

Battery Information

CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of batteries

according to instructions.

Use only Zebra approved batteries. Accessories which have battery charging
capability are approved for use with the following battery models:

• ModelBT-000370 (3.6 VDC, 7,000 mAh)

• Model BT-000371 (3.6 VDC, 5,000 mAh)

Zebra approved rechargeable battery packs are designed and constructed to the
highest standards within the industry.

However, there are limitations to how long a battery can operate or be stored before
needing replacement. Many factors affect the actual life cycle of a battery pack, such
as heat, cold, harsh environmental conditions and severe drops.

When batteries are stored over six (6) months, some irreversible deterioration in
overall battery quality may occur. Store batteries at half of full charge in a dry, cool
place, removed from the equipment to prevent loss of capacity, rusting of metallic
parts and electrolyte leakage. When storing batteries for one year or longer, the
charge level should be verified at least once a year and charged to half of full charge.

Replace the battery when a significant loss of run time is detected.
Standard warranty period for all Zebra batteries is one year, regardless if the battery

was purchased separately or included as part of the mobile computer or bar code
scanner. For more information on Zebra batteries, please visit: www.zebra.com/

batterybasics.

Battery Safety Guidelines

The area in which the units are charged should be clear of debris and combustible
materials or chemicals. Particular care should be taken where the device is charged
in a non-commercial environment.

• Follow battery usage, storage, and charging guidelines found in the user's guide.

• Improper battery use may result in a fire, explosion, or other hazard.

合 格 证

• To charge the mobile device battery, the battery and charger temperatures must
be between +32°F and +113°F (0°C and +45°C).

• Do not use incompatible batteries and chargers. Use of an incompatible battery or
charger may present a risk of fire, explosion, leakage, or other hazard. If you have
any questions about the compatibility of a battery or a charger, contact Zebra
support.

• Do not disassemble or open, crush, bend or deform, puncture, or shred.

• Severe impact from dropping any battery-operated device on a hard surface could
cause the battery to overheat.

• Do not short circuit a battery or allow metallic or conductive objects to contact the
battery terminals.

• Do not modify or remanufacture, attempt to insert foreign objects into the battery,
immerse or expose to water or other liquids, or expose to fire, explosion, or other
hazard.

• Do not leave or store the equipment in or near areas that might get very hot, such
as in a parked vehicle or near a radiator or other heat source. Do not place battery
into a microwave oven or dryer.

• Battery usage by children should be supervised.

• Please follow local regulations to promptly dispose of used re-chargeable
batteries.

• Do not dispose of batteries in fire.

• Seek medical advice immediately if a battery has been swallowed.

• In the event of a battery leak, do not allow the liquid to come in contact with the
skin or eyes. If contact has been made, wash the affected area with large
amounts of water and seek medical advice.

• If you suspect damage to your equipment or battery, contact Zebra support to
arrange for inspection.

Radio Frequency Interference Requirements-FCC

Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected

• Consult the dealer or an experienced radio/TV technician for help.

Radio Transmitters (Part 15)

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.

Radio Frequency Interference Requirements - Canada

CAN ICES-3 (B)/NMB-3(B)

Radio Transmitters

This device complies with Industry Canada's licence-exempt RSSs. Operation is
subject to the following two conditions: (1) This device may not cause interference;
and (2) This device must accept any interference, including interference that may
cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radio électrique subi même si le brouillage est
susceptible d'en compromettre le fonctionnement.

Marking and European Economic Area
(EEA)

The use of 5 GHz RLAN throughout the EEA has the following restrictions:

• 5.15 - 5.35 GHz is restricted to indoor use only.

Statement of Compliance

Zebra hereby declares that this radio equipment is in compliance with Directives 2014/
53/EU and 2011/65/EU.

The full text of the EU Declaration of Conformity is available at the following internet
address: zebra.com/doc

Other Countries

Australia

The use of 5 GHz RLAN in Australia is restricted in the following band 5.60 –

5.65GHz.

.

Brazil

Declarações Regulamentares para MC930B, MC930P - Brasil

Nota: A marca de certificação se aplica ao Transceptor, mod . Este equipamento não
tem direito à proteção contra interferência prejudicial e não pode causar interferência
em Sistemas devidamente autorizados.

Para maiores informações sobre ANATEL consulte o site: www.anatel.gov.br.
Este produto está homologado pela Anatel, de acordo com os procedimentos

regulamentados pela Resolução n°242/2000 e atende aos requisitos técnicos
aplicados, incluindo os limites de exposição da Taxa de Absorção Específica
referente a campos elétricos, magnéticos e eletromagnéticos de radiofrequência, de
acordo com as Resoluções n° 303/2002 e 533/2009.

“Este dispositivo está em conformidade com as diretrizes de exposição à
radiofrequência quando posicionado pelo menos a centímetros de distância do
corpo.”

Chile

Este equipo cumple con la Resolución No 403 de 2008, de la Subsecretaria de
telecomunicaciones, relativa a radiaciones electromagnéticas.

Conforme a Resolución 755 parte j.1), se ajustará el dispositivo a operar en interiores
en las siguientes bandas con una potencia máxima radiada no superior a 150mW:

• 2.400 a 2.483,5 MHz

• 5.150 a 5.250MHz

• 5.250 a 5.350MHz

• 5.470 a 5.725MHz

• 5.725 a 5.850MHz
Además, de acuerdo con Resolución 755, para la banda 5150-5250MHz la operación

del equipo estará restringida al interior de inmuebles y la densidad de potencia
radiada máxima no supera 7,5mW/MHz en cualquier banda de 1MHz y 0.1875mW/
25kHz en cualquier banda de 25kHz.

Para la tecnología NFC en la banda 13.553 a 13.567 kHz, la intensidad de campo
eléctrico no excederá 20 mV/m a 30 metros, conforme a Resolucion 755 parte Art 1.
e).

China

通过访问以下网址可下载当地语言支持的产品说明书

www.zebra.com/support

锂电池安全警示语 :
警告： 请勿拆装，短路，撞击，挤压或者投入火中
注意： 如果电池被不正确型号替换，或出现鼓胀，会存在爆炸及其他危险
请按说明处置使用过的电池
电池浸水后严禁使用
合格证：

Eurasian Customs Union

ЕвразийскийТаможенныйСоюз

Данный продукт соответствует требованиям знака EAC.

Hong Kong

In accordance with HKTA1039, the band 5.15GHz - 5.35GHz is for indoor operation
only.

Mexico

La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es
posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este
equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda
causar su operación no deseada.

Taiwan

臺灣
低功率電波輻射性電機管理辦法
第十二條
經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更

頻率、加大功率或變更原設計之特性及功能。
第十四條
低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應

立即停用，並改善至無干擾時方得繼續使用。
前項合法通信，指依電信法規定作業之無線電通信。
低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
應避免影響附近雷達系統之操作
公司資訊

台灣斑馬科技股份有限公司 / 台北市信義區松高路 9 號 13 樓

Turkey

Bu cihaz Türkçe karakterlerin tamamını ihtiva eden ETSI TS 123.038 V8.0.0 (veya
sonraki sürümünkodu) ve ETSI TS 123.040 V8.1.0 (veya sonraki sürümün kodu)
teknik özelliklerine uygundur.

Ukraine

Дане обладнання відповідає вимогам технічного регламенту № 1057, 2008 на
обмеження щодо використання деяких небезпечних речовин в електричних та
електронних пристроях.

Thailand

เครื่ องโทรคมนาคมและอุ ปกรณ นี้ มี ความสอดคล องตามข อกําหนดของ กทช .

Waste Electrical and Electronic
Equipment (WEEE)

English: For EU Customers: All products at the end of their life must be

please go to: www.zebra.com/weee
Français: Clients de l'Union Européenne: Tous les produits en fin de cycle de vie

doivent être retournés à Zebra pour recyclage. Pour de plus amples informations sur
le retour de produits, consultez : www.zebra.com/weee.

Español: Para clientes en la Unión Europea: todos los productos deberán entregarse
a Zebra al final de su ciclo de vida para que sean reciclados. Si desea más
información sobre cómo devolver un producto, visite: www.zebra.com/weee.

Bulgarish: За клиенти от ЕС: След края на полезния им живот всички продукти
трябва да се връщат на Zebra за рециклиране. За информация относно
връщането на продукти, моля отидете на адрес: www.zebra.com/weee.

Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende ihrer
Lebensdauer zum Recycling an Zebra zurückgesandt werden. Informationen zur
Rücksendung von Produkten finden Sie unter www.zebra.com/weee.

Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo
ciclo di vita devono essere restituiti a Zebra al fine di consentirne il riciclaggio. Per
informazioni sulle modalità di restituzione, visitare il seguente sito Web:
www.zebra.com/weee.

Português: Para clientes da UE: todos os produtos no fim de vida devem ser
devolvidos à Zebra para reciclagem. Para obter informações sobre como devolver o
produto, visite: www.zebra.com/weee.

Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun
levensduur naar Zebra te worden teruggezonden voor recycling. Raadpleeg
www.zebra.com/weee voor meer informatie over het terugzenden van producten.

Polski: Klienci z obszaru Unii Europejskiej: Produkty wycofane z eksploatacji należy
zwrócić do firmy Zebra w celu ich utylizacji. Informacje na temat zwrotu produktów
znajdują się na stronie internetowej www.zebra.com/weee.

Čeština: Pro zákazníky z EU: Všechny produkty je nutné po skonèení jejich životnosti
vrátit spoleènosti Zebra k recyklaci. Informace o zpùsobu vrácení produktu najdete na
webové stránce: www.zebra.com/weee.

Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada
taaskasutamise eesmärgil Zebra'ile. Lisainformatsiooni saamiseks toote tagastamise
kohta külastage palun aadressi: www.zebra.com/weee.

Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Zebra vállalathoz
kell eljuttatni újrahasznosítás céljából. A termék visszajuttatásának módjával
kapcsolatos tudnivalókért látogasson el a www.zebra.com/weee we

Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste
returneras till Zebra för återvinning. Information om hur du returnerar produkten finns
på www.zebra.com/weee.

Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava
kierrätettäväksi Zebra-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja tuotteen
palauttamisesta on osoitteessa www.zebra.com/weee.

Dansk: Til kunder i EU: Alle produkter skal returneres til Zebra til recirkulering, når de
er udtjent. Læs oplysningerne om returnering af produkter på: www.zebra.com/weee.

Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο τέλος της διάρκειας ζωής
τους, πρέπει να επιστρέφονται στην Zebra για ανακύκλωση. Για περισσότερες
πληροφορίες σχετικά με την επιστροφή ενός προϊόντος, επισκεφθείτε τη διεύθυνση
www.zebra.com/weee στο Διαδίκτυο.

Malti: Għal klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-aħħar tal-ħajja ta' l-użu
tagħhom, iridu jiġu rritornati għand Zebra għar-riċiklaġġ. Għal aktar tagħrif dwar kif
għandek tirritorna l-prodott, jekk jogħġbok żur: www.zebra.com/weee.

Românesc: Pentru clienţii din UE: Toate produsele, la sfârşitul duratei lor de
funcţionare, trebuie returnate la Zebra pentru reciclare. Pentru informaţii despre
returnarea produsului, accesaţi: www.zebra.com/weee.

Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti
podjetju Zebra za reciklažo. Za informacije o vračilu izdelka obiščite: www.zebra.com/
weee.

Slovenčina: Pre zákazníkov z krajín EU: Všetky výrobky musia byť po uplynutí doby
ich životnosti vrátené spoločnosti Zebra na recykláciu. Bližšie informácie o vrátení
výrobkov nájdete na: www.zebra.com/weee.

returned to Zebra for recycling. For information on how to return product,

.

boldalra.

Lietuvių: ES vartotojams: visi gaminiai, pasibaigus jų eksploatacijos laikui, turi būti
grąžinti utilizuoti į kompaniją „Zebra“. Daugiau informacijos, kaip grąžinti gaminį,
rasite: www.zebra.com/weee.

Latviešu: ES klientiem: visi produkti pēc to kalpošanas mūža beigām ir jānogādā
atpakaļ Zebra otrreizējai pārstrādei. Lai iegūtu informāciju par produktu nogādāšanu
Zebra, lūdzu, skatiet: www.zebra.com/weee.

Türkçe: AB Müşterileri için: Kullanım süresi dolan tüm ürünler geri dönüştürme için
Zebra'ya iade edilmelidir. Ürünlerin nasıl iade edileceği hakkında bilgi için lütfen şu
adresi ziyaret edin: www.zebra.com/weee.

Turkish WEEE Statement of Compliance

EEE Yönetmeliğine Uygundur.

End User License Agreement

For complete EULA information, go to www.zebra.com/eula.

Software Support

Zebra wants to ensure that customers have the latest entitled software at the time of
device purchase in order to keep the device operating at peak performance levels. To
confirm that your Zebra device has the latest entitled software available at the time of
purchase, visit www.zebra.com/support

Check for the latest software from Support > Products, or search for the device and
select Support > Software Downloads.

If your device does not have the latest entitled software as of your device purchase
date, e-mail Zebra at [e-mail] and ensure you include the
following essential device information:

• Model number

• Serial number

• Proof of purchase

• Title of the software download you are requesting.
If it is determined by Zebra that your device is entitled to the latest version of software,

as of the date you purchased your device, you will receive an e-mail containing a link
directing you to a Zebra Web site to download the appropriate software.

CMM Disclosure

部件名称

(Parts)

铅

(Pb)汞(Hg)镉(Cd)

金属部件

(Metal Parts)

电路模块

(Circuit Modules)

电缆及电缆组件

(Cables and Cable
Assemblies)

塑料和聚合物部件

(Plastic and Polymeric
Parts)

光学和光学组件

(Optics and Optical
Components)

电池

(Batteries)

本表格依据 SJ/T 11364 的规定编制。

O:表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572 规定的限量要求

以下。

X:表示该有害物质至少在该部件的某一均质材料中的含量超出GB/T 26572 规定的限量

要求。(企业可在此处，根据实际情况对上表中打“×”的技术原因进行进一步说
明。）

This table was created to comply with China RoHS requirements.

.

有害物质

六价铬

多溴联苯

(Cr(VI))

XOO O O O

XOO O O O

OOO O O O

OOO O O O

OOX O O O

OOO O O O

(PBB)

多溴二苯醚

(PBDE)

限用物質含有情況標示聲明書

設備名稱： 移動式電腦
Equipment name

單元

Unit

印刷電路板及電子組件 − O O O O O
金屬零件 − O − O O O
電纜及電纜組件 O O O O O O
塑料和聚合物零件 O O O O O O
光學與光學元件 O O O O O O

Restricted substances and its chemical

鉛 (Pb)

備考 1. 〝超出 0.1 wt % 〞及〝超出 0.01 wt % 〞係指限用物質之百分比含量
超出百分比含量基準值。

Note 1: “Exceeding 0.1 wt%” and “exceeding 0.01 wt%” indicate that the
percentage content of the restricted substance exceeds the reference
percentage value of presence condition.

備考 2. 〝 O 〞係指該項限用物質之百分比含量未超出百分比含量基準值。
Note 2: “O” indicates that the percentage content of the restricted substance

does not exceed the percentage of reference value of presence.
備考 3. 〝−〞係指該項限用物質為排除項目。
Note 3: The “ − ” indicates that the restricted substance corresponds to the

exemption.

Warranty

For the complete Zebra hardware product warranty statement, go to www.zebra.com/

warranty.

型號 （型式）： MC93XX
Type designation (Type)

限用物質及其化學符號

symbols

)

+6

汞 (Hg)

鎘 (Cd)

六價鉻 (Cr

(PBB)

多溴聯苯

多溴二苯醚

(PBDE)

Service Information

Before you use the unit, it must be configured to operate in your facility’s network and
run your applications.

If you have a problem running your unit or using your equipment, contact your facility’s
Technical or Systems Support. If there is a problem with the equipment, they will
contact the Zebra Global Customer Support at

For the latest version of this guide go to www.zebra.com/support.

www.zebra.com/support.