Zebra Technologies ET51CE User Manual

ET51/56

Enterprise Tablet

Quick Reference Guide

2 ET51/56 Enterprise Tablet

ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corporation, registered in many jurisdictions worldwide. All other trademarks are the property of their respective owners. ©2019 Zebra Technologies Corporation and/or its affiliates. All rights reserved.

COPYRIGHTS & TRADEMARKS: For complete copyright and trademark information, go to

www.zebra.com/copyright.

WARRANTY: For complete warranty information, go to www.zebra.com/warranty. END USER LICENSE AGREEMENT: For complete EULA information, go to

www.zebra.com/eula.

• Proprietary Statement This manual contains proprietary information of Zebra Technologies Corporation and its

subsidiaries (“Zebra Technologies”). It is intended solely for the information and use of parties operating and maintaining the equipment described herein. Such proprietary information may not be used, reproduced, or disclosed to any other parties for any other purpose without the express, written permission of Zebra Technologies.

• Product Improvements Continuous improvement of products is a policy of Zebra Technologies. All

specifications and designs are subject to change without notice.

• Liability Disclaimer Zebra Technologies takes steps to ensure that its published Engineering specifications

and manuals are correct; however, errors do occur. Zebra Technologies reserves the right to correct any such errors and disclaims liability resulting therefrom.

• Limitation of Liability In no event shall Zebra Technologies or anyone else involved in the creation,

production, or delivery of the accompanying product (including hardware and software) be liable for any damages whatsoever (including, without limitation, consequential damages including loss of business profits, business interruption, or loss of business information) arising out of the use of, the results of use of, or inability to use such product, even if Zebra Technologies has been advised of the possibility of such damages. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

Warranty

For the complete Zebra hardware product warranty statement, go to

www.zebra.com/warranty.

Service Information

If you have a problem using the equipment, contact your facility’s Technical or Systems Support. If there is a problem with the equipment, they will contact the Zebra Support at: zebra.com/support.

For the latest version of this guide go to: zebra.com/support.

Quick Reference Guide 3

1342 52

Introduction

The ET51 is a wireless LAN (WLAN) tablet and the ET56 is a wireless WAN (WWAN) tablet.

Features

Item Description

1 Ambient Light Sensor - Recognizes the ambient light and adjusts the

display brightness (if enabled). 2 Front Microphones - Use for voice communications or audio recordings. 3 Front Facing Camera - Use for video conferencing or capturing images and

video. 4 Camera Indicator LED - Lights red when the camera is activate.

5 Charging Indicator LED - Indicates charging status.

Momentarily lights red when the device boots and shuts down.

OFF - device is not connected to charger.

ORANGE - device is charging.

GREEN - device is connected and fully charged.

RED - charge error.

4 ET51/56 Enterprise Tablet

8” Version

10” Version

Item Description

6 Rear Camera - Use for high resolution images and video. 7 Camera LED Flash - Provides illumination for the camera. 8 Power Button - Push once to start the device; push it again to enable sleep

mode. Push and hold it to shut down the device.

9 Volume Key - Push the left side to reduce the volume. Press the right side to

increase the volume. 10 USB-C Interface - Provides for communication. 11 Back Cover - Covers the service replaceable battery.

Item Description

12 NFC Antenna Position - Use to read NFC cards and RFID tags. 13 Stereo Speakers - Provides audio playback. 14 Docking Connector - Interfaces with the cradle.

Quick Reference Guide 5

8.4” Version

Locking Tabs

10.1” Version

Locking Tabs

Installing a micro SD Card or SIM Card

To install a microSD card and/or nano SIM card (ET56 only):

1. Press the Power button to turn off the device.

2. Lift the notched corner of the battery cover.

3. Carefully lift the battery cover off the device.

4. On the 8.4” version, push the two locking tabs up, then pull up on the tab to remove battery.

On the 10.1” version, push the two locking tabs up (1), then, using index fingers, lift the battery up (2).

6 ET51/56 Enterprise Tablet

ET51AE/ET56BE

ET51AT/ET51CT/ET56BT

ET51CE/ET56DE

NANO

ET56BE

ET56BT

ET56DE

5. Insert the microSD card with contacts facing down.

6. Push the micro SD card in and ensure that it locks into place.

7. Insert the nano SIM card with contacts facing down.

8. Push the SIM card in and ensure that it locks into place.

9. Replace the battery.

Quick Reference Guide 7

CAUTION: Be aware of the orientation of the battery cover. Failure to replace the

battery cover properly may damage the battery cover.

10. Align the tabs on the underside of the cover with the slot around the battery well. Make sure that the notch on the battery cover is at the bottom left cover of the device.

11. Carefully press down around the edge of the cover. Make sure that the cover is seated properly.

12. Press Power button to turn on the device.

Charging the Device

Use the Communication and Charging Cradle, Rugged Communication and Charging Cradle or Charge Only Cradle to charge the device. See ET51/56 User Guide for more information.

NOTE: The Charge Only Cradle (CRD-ET5X-1SCG1) and the Communication and

Charge Cradle (CRD-ET5X-1SCOM1) come with two inserts; tall insert and short insert. Install the tall insert when using a device without a Rugged Frame and Expansion Back. Install the small insert when using a device with an Expansion Back and without a Rugged Frame. Do not install either insert when using the device with the Rugged Frame.

The Rugged Communication and Charge Cradle (CRD-ET5X-1SCOM1R) does not come with inserts. Use with device and Rugged Frame with IO Adapter.

8 ET51/56 Enterprise Tablet

Communication CradleCharge Only Cradle

Short Insert

Rugged Communication Cradle

Tall Insert

Communication and Charging Cradle Charge Only Cradle

Cradle Insert Required

Cradle Insert Not Required

Richten Sie die Ladestation oder die Kommunikationsstation ein. Netzteil (PWR-BGA12V50W0WW), DC-Netzkabel (CBL-DC-388A1-01) und länderspezifisches AC-Netzkabel sind separat erhältlich.

1. If using the Communication and Charging Cradle, open the bottom access door and hold it to the back of the tablet.

2. Align the device with the alignment pins on the cradle.

3. Insert the device into the cradle. Note that the Communication Cradle contains a locking mechanism that locks the device to the cradle.

+ 16 hidden pages