TC5X/TC7X
Workstation
Cradle
User Guide
MN-003856-02EN
ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corporation, registered in
many jurisdictions worldwide. All other trademarks are the property of their respective owners.
© 2020 Zebra Technologies Corporation and/or its affiliates. All rights reserved.
Information in this document is subject to change without notice. The software described in this document
is furnished under a license agreement or nondisclosure agreement. The software may be used or copied
only in accordance with the terms of those agreements.
For further information regarding legal and proprietary statements, please go to:
SOFTWARE:http://www.zebra.com/linkoslegal
COPYRIGHTS:http://www.zebra.com/copyright
WARRANTY:http://www.zebra.com/warranty
END USER LICENSE AGREEMENT: http://www.zebra.com/eula
Terms of Use
Proprietary Statement
This manual contains proprietary information of Zebra Technologies Corporation and its subsidiaries
(“Zebra Technologies”). It is intended solely for the information and use of parties operating and
maintaining the equipment described herein. Such proprietary information may not be used, reproduced,
or disclosed to any other parties for any other purpose without the express, written permission of Zebra
Technologies.
Product Improvements
Continuous improvement of products is a policy of Zebra Technologies. All specifications and designs are
subject to change without notice.
Liability Disclaimer
Zebra Technologies takes steps to ensure that its published Engineering specifications and manuals are
correct; however, errors do occur. Zebra Technologies reserves the right to correct any such errors and
disclaims liability resulting therefrom.
Limitation of Liability
In no event shall Zebra Technologies or anyone else involved in the creation, production, or delivery of the
accompanying product (including hardware and software) be liable for any damages whatsoever
(including, without limitation, consequential damages including loss of business profits, business
interruption, or loss of business information) arising out of the use of, the results of use of, or inability to
use such product, even if Zebra Technologies has been advised of the possibility of such damages. Some
jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
Publication Date
August 3, 2020
2
Introduction
The TC5X and TC7X Workstation Cradle is an enhanced single-slot charging cradle with additional ports
for HDMI, Ethernet, and four USB ports that enable a TC5X or TC7X device to be used as a workstation
computer when connected to a HDMI monitor, keyboard and mouse. The TC5X cradle supports TC52, and
TC57 devices. The TC7X cradle supportsTC72, and TC77 devices.
The workstation cradle provide:
• 5 VDC power for operating the device.
• Three 0.5 mA USB ports for USB devices (keyboard, mouse, USB scanner, etc.).
• One 1.5 mA USB port for a USB device or for charging a personal mobile device.
• One HDMI port for connection to a monitor.
NOTE: If the user also wants audio support, they need to use a monitor that has speakers (audio through
the HDMI connection).
If the user also wants to support a touch monitor, they need to use a monitor that supports touch inputs
and connect the feature to one of the USB ports of the cradle.
• One Ethernet port for connection to a wired Ethernet network.
In the Box
The kit contains:
• workstation cradle
• power supply
• DC cable
• regulatory guide.
Inspect the equipment for damage. If any equipment is missing or damaged, contact the Global Customer
Support center immediately.
2
Features
Figure 1 Left Side View (TC5X Cradle Shown)
1
23
Item Description
1 LED - Indicates that power is applied to the cradle.
2 1.5 mA USB Port - USB Type A port for mouse or keyboard, or personal mobile device.
3 0.5 mA USB Port - USB Type A port for mouse or keyboard.
Figure 2 Rear/Right Side View (TC5X Cradle Shown)
9
8
7
6
Item Description
4 Ethernet Port - Connects to an Ethernet network.
5 HDMI Port - Connects to monitor.
6 Power Port - Provides power to the cradle.
7 USB Type A Port - Connection for mouse or keyboard.
8 USB Type A Port - Connection for mouse or keyboard.
9 Kensington Slot - Connecting point for Kensington locking system to secure cradle.
4
5
3
Setup
Figure 3 Workstation Cradle Setup (TC5X Cradle Shown)
Monitor Power Supply
AC Line Cord
Cradle
HDMI Cable
USB Keyboard
Ethernet Switch
Ethernet Cable
USB Scanner
USB Cable
USB Mouse
4
Ethernet Setup
For device Ethernet setup, refer to the device Integrator Guide.
Scanner Setup
The workstation cradle only supports a USB scanner in Human Interface Device (HID) mode. Refer to the
scanner Product Reference Guide for information on configuring the scanner to HID mode.
Bluetooth Device Setup
Bluetooth devices such as keyboard and mouse can be connected to the device. Follow Bluetooth
instructions in the device User Guide for connecting these peripherals to the device.
Security
The cradle provides a Kensington Slot to secure the cradle using a Kensington locking cable.
Figure 4 Securing Cradle with Kensington Lock
Using the Workstation Cradle
Turn on the device.
1. Insert the device into the cradle.
The device screen automatically rotates and mirrors on the connected monitor.
Changing Monitor Resolution
Screen resolution is automatically detected by the device when placed in the cradle. To manually change
the external monitor screen resolution:
1. Go to Settings > Display > External screen resolution.
2. Select the a resolution for the attached monitor.
3. Insert the device into the cradle.
Charging the Device
To charge a device:
5
NOTE: If a TC5X has a Rugged Boot, remove the cup insert before inserting the device.
1. Insert the device into the slot to begin charging.
Figure 5 Battery Charging (TC5X Cradle Shown)
2. Ensure the device is seated properly.
Inserting a TC5X with Rugged Boot into Cradle
NOTE: Applies to TC5X devices only.
Each TC5X cradle cup has an insert that must be removed prior to inserting the TC5X with Rugged Boot.
Remove the insert and then insert the TC5X into the cup.
6
Figure 6 Remove Insert from Cup
Cleaning
Refer to the device User Guide for cleaning instructions.
Troubleshooting
Table 1 Troubleshooting
Problem Cause Solution
External monitor not
detected.
Display does not change
orientation quickly.
Devices does not switch
to landscape mode.
Peripheral not detected. Bad cable connection. Remove cable and re-connect.
The device is powered off when
placed in the cradle and then
turns on.
It takes a little time for the
device to recognize the monitor.
Device not detecting monitor. Remove the device from the cradle and
Display setting not set properly. Go to Settings > Display > When device
Remove the device from the cradle and
re-insert. The device will then detect the
monitor.
Wait for screen to re-orientate.
re-insert.
detects external monitor. Ensure
Rotate screen orientation is selected.
7
Specifications
TC5X Cradle
Table 2 TC5X Cradle Technical Specifications
Dimensions Height: 9.9 cm (3.9 in.)
Weight 378 g (13.3 oz.)
Input Voltage 12 VDC
Power Consumption up to 48 watts
Operating Temperature 0°C to 40°C (32°F to 104°F)
Storage Temperature -40°C to 70°C (-40°F to 158°F)
Charging Temperature 0°C to 40°C (32°F to 104°F)
Humidity 5% to 95% non-condensing
Drop 76.2 cm (30.0 in.) drops to vinyl tiled concrete at room temperature.
Electrostatic Discharge
(ESD)
Item Description
Width: 9.8 cm (3.86 in.)
Depth: 13.3 cm (5.24 in.)
+/- 20kV air
+/- 10 kV contact
+/- 10 kV indirect discharge
TC7X Cradle
Table 3 TC7X Cradle Technical Specifications
Dimensions Height: 20.7 cm (7.9 in.)
Weight 451 g (15.9 oz.)
Input Voltage 12 VDC
Power Consumption up to 48 watts
Operating Temperature 0°C to 40°C (32°F to 104°F)
Storage Temperature -40°C to 70°C (-40°F to 158°F)
Charging Temperature 0°C to 40°C (32°F to 104°F)
Item Description
Width: 9.8 cm (3.86 in.)
Depth: 13.3 cm (5.24 in.)
8
Table 3 TC7X Cradle Technical Specifications (Continued)
Item Description
Humidity 5% to 95% non-condensing
Drop 76.2 cm (30.0 in.) drops to vinyl tiled concrete at room temperature.
Electrostatic Discharge
(ESD)
+/- 20kV air
+/- 10 kV contact
+/- 10 kV indirect discharge
9
www.zebra.com
Loading...