Zebra DS3578 Quick Start Manual

DS3578 with FIPS

Quick Start Guide

POST IN WORK AREAPOST IN WORK AREA

See Product Reference Guide for detailed information

1 Tether Plate 2 LED Indicators 3 Scan Window 4 Scan Trigger

Caution: DS3478 cordless scanners are incompatible with STB3508/3578 cradles. DS3578 cordless scanners are incompatible with STB3408/3478 cradles.

Cradle Insertion

STEP 1 - BATTERY INSERTION/REMOVAL

Or use coin Or use coin

STEP 2 - CRADLE CABLE CONNECTION

Power

Connect to Appropriate Host

Power

Host

STEP 3 - CONNECT HOST INTERFACE

NOTE: Cables may vary depending on configuration

RS-232

Host

STEP 4 - SET UP INTERFACE (Scan Host Bar Codes)

RS-232

Scan ONE of the bar codes below

STANDARD RS-232

NIXDORF RS-232 MODE B

Power

(if required)

NIXDORF RS-232 MODE A

USB

ICL RS-232

USB

Scan ONE of the bar codes below

HID KEYBOARD EMULATION

IBM HAND-HELD USB

FUJITSU RS-232

OPOS/JPOS

SNAPI WITH IMAGING (For use with hands-free base only)

SNAPI WITHOUT IMAGING (For use with hands-free base only)

NOTE: SNAPI is for use with FIPS enabled scanner and FIPS enabled cradle only.

IBM 46XX

Keyboard Wedge

IBM 46XX

Scan ONE of the bar codes below

PORT 5B

Scan bar codes below

PORT 9B

123SCAN2Keyboard Wedge

Set Defaults

Note: The scanner connection to the cradle is dissolved when Set Defaults is scanned.

IBM PC/AT and IBM PC COMPATIBLE

PROGRAMMING BAR CODES

Carriage Return/Line Feed Radio Communications Host Types

123Scan2 is an easy-to-use, PC-based

software tool that enables rapid and easy

customized setup via a bar code or USB

cable. For more information, visit:

http://www.zebra.com/123Scan2

FIPS MODE

NOTE:

Requires a FIPS enabled DS3578 scanner (DS3578-XXF005WR) and FIPS enabled cradle (STB/FLB3578-CF007WR).

SET DEFAULTS

Unpairing/Disconnection

UNPAIR/DISCONNECT

SCAN OPTIONS

ENTER

CRADLE HOST

SERIAL PORT PROFILE (SLAVE)

BLUETOOTH KEYBOARD EMULATION (HID SLAVE)

SERIAL PORT PROFILE (MASTER)

FIPS

Scan ONE of the bar codes below

Enable FIPS

*Disable FIPS

DS3578 with FIPS

Quick Start Guide

1 Tether Plate 2 LED Indicators 3 Scan Window 4 Scan Trigger

LED Indicator

Aiming

OPTIMUM SCANNING POSITIONS

Aiming

01234 5

POST IN WORK AREA

Optimum body posture

for low scanning

ALTERNATE LEFT AND RIGHT HANDS

TAKING BREAKS AND TASK ROTATION RECOMMENDED

OPTIMUM BODY POSTURE

Optimum body posture for

extended range scanning

AVOID EXTREME

WRIST ANGLES

AVOID BENDING

Alternate left and right knees

TROUBLESHOOTING

Please refer to the DS3578 Product Reference Guide Troubleshooting section for further information.

Ergonomic Recommendations

Caution: In order to avoid or minimize the potential risk of ergonomic injury, follow the recommenda-

tions below. Consult with your local Health & Safety Manager to ensure that you are adhering to your company's safety programs to prevent employee injury.

• Reduce or eliminate repetitive motion

• Maintain a natural/neutral position

• Reduce or eliminate excessive force

• Keep objects that are used frequently within easy reach

• Perform tasks at correct heights

Beeper Indications

AVOID REACHING

• Reduce or eliminate vibration

• Reduce or eliminate direct pressure

• Provide adjustable workstations

• Provide adequate clearance

• Provide a suitable working environment

• Improve work procedures

BEEPER/LED INDICATIONS

(Standard Use)

Scanner not working

No power to scanner

Check battery

End cap not secured correctly

Turn end cap to secure

Scanner decoding bar code, but data not transmitting to host

Scanner not paired to host-connected cradle Cradle not programmed for correct host interface

Pair the scanner to the cradle (using the

Check scanner host parameters or edit options

PAIR bar code on the cradle)

Note: If data is still not transmitting to host, it may be necessary to recycle power on the cradle.

Scanner not decoding bar code

Scanner not programmed for bar code type

Ensure scanner is programmed to read type of bar code being scanned

Bar code unreadable

Ensure bar code is not defaced; try scanning test bar code of same bar code type

Interface cable is loose

Check for loose cable connections

Low-medium-high beeps

Power up

Normal beep 4 long low beeps

Bar code decoded [if decode beeper enabled]

Short low-high beeps Short high-low beeps

Scanner has paired with the cradle

Scanner has unpaired with the cradle

Parameter Menu Scanning

High-low-high-low beeps

Successful program exit with change in the parameter setting

LED Indications

(Standard Use)

Off Green

No power applied to scanner (battery

Bar code successfully decoded discharged or removed), or scanner is in low power and ready to scan

Charging Use

Transmission error detected; data is ignored

Long low-high beeps or Long low-high-low-high beeps

Unsuccessful pairing attempt

Long low-high beeps

Input error, incorrect programming sequence,or Cancel bar code scanned

4 short high beeps

Low battery indication

Red

Data transmission error or scanner malfunction or DS3578 scanner inserted into an STB3478 cradle

Scanned data incorrectly displayed on host

Paired cradle host communication parameters do not match the host’s parameters

Check cradle host parameters or edit options

DS3578 with FIPS

Regulatory Information

This guide applies to Model Number DS3578 with FIPS. All Zebra devices are designed to be compliant with rules and regulations in locations they are sold and will be labeled as required. Local language translations are available at: http://www.zebra.com/support. Any changes or modifications to Zebra equipment, not expressly approved by Zebra, could void the user's authority to operate the equipment.Declared maximum operating temperature: 50°C.

CAUTION:

Only use Zebra approved and UL Listed accessories, battery packs and battery chargers. Do NOT attempt to charge damp/wet batteries. All components must be dry before connecting to an external power source.

Waste Electrical and Electronic Equipment (WEEE)

English: For EU Customers: All products at the end of their life must be returned to Zebra for recycling. For information on how to return product, please go to: http://www.zebra.com/weee.

Bulgarish: За клиенти от ЕС: След края на полезния им живот всички продукти трябва да се връщат на Zebra за рециклиране. За информация относно връщането на продукти, моля отидете на адрес:

http://www.zebra.com/weee. Čeština: Pro zákazníky z EU: Všechny produkty je nutné po skonèení jejich

životnosti vrátit spoleènosti Zebra k recyklaci. Informace o zpùsobu vrácení produktu najdete na webové stránce: http://www.zebra.com/weee.

Dansk: Til kunder i EU: Alle produkter skal returneres til Zebra til recirkulering, når de er udtjent. Læs oplysningerne om returnering af produkter på: http://www.zebra.com/weee. Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende ihrer

Lebensdauer zum Recycling an Zebra zurückgesandt werden. Informationen zur Rücksendung von Produkten finden Sie unter http://www.zebra.com/weee. Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο τέλος της διάρκειας ζωής τους, πρέπει να επιστρέφονται στην Zebra για ανακύκλωση. Για περισσότερες πληροφορίες σχετικά με την επιστροφή ενός προϊόντος, επισκεφθείτε τη διεύθυνση http://www.zebra.com/weee στο Διαδίκτυο.

Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada taaskasutamise eesmärgil Zebra'ile. Lisainformatsiooni saamiseks toote tagastamise kohta külastage palun aadressi: http://www.zebra.com/weee. Español: Para clientes en la Unión Europea: todos los productos deberán

entregarse a Zebra al final de su ciclo de vida para que sean reciclados. Si desea más información sobre cómo devolver un producto, visite:

http://www.zebra.com/weee.

Français : Clients de l'Union Européenne : Tous les produits en fin de cycle de vie doivent être retournés à Zebra pour recyclage. Pour de plus amples informations

sur le retour de produits, consultez : http://www.zebra.com/weee.

Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita devono essere restituiti a Zebra al fine di consentirne il riciclaggio. Per informazioni sulle modalità di restituzione, visitare il seguente sito Web:

http://www.zebra.com/weee.

Latviešu: ES klientiem: visi produkti pēc to kalpošanas mūža beigām ir jānogādā atpakaļ Zebra otrreizējai pārstrādei. Lai iegūtu informāciju par produktu nogādāšanu Zebra, lūdzu, skatiet: http://www.zebra.com/weee.

Wireless Device Country Approvals

Regulatory markings, subject to certification, are applied to the device signifying the radio(s) are approved for use in the followingcountries: United States, Canada, Japan, China, S. Korea, Australia, & Europe1.

Please refer to the Zebra Declaration of Conformity (DoC) for details of other country markings. This is available at: http://www.zebra.com/doc. Note1: For 2.4GHz or 5GHz Products: Europe includes, Austria, Belgium, Bulgaria, Czech Republic, Cyprus, Denmark, Estonia, Finland,

France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, MaltaNetherlands, Norway, Poland, Portugal, Romania, Slovak Republic, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.

Operation of the device without regulatory approval is illegal.

Bluetooth Wireless Technology

This is an approved Bluetooth product. For more information or to view End Product Listing, please visit https://www.bluetooth.org/tpg/listings.cfm

Warnings for Use of Wireless Devices

Please observe all warning notices with regard to the usage of wireless devices.

Potentially Hazardous Atmospheres – Vehicles Use

You are reminded of the need to observe restrictions on the use of radio devices in fuel depots, chemical plants etc. and areas where the air contains chemicals or particles (such as grain, dust, or metal powders) and any other area where you would normally be advised to turn off your vehicle engine.

Potentially Hazardous Atmospheres – Fixed Installations

Safety in Aircraft

Switch off your wireless device whenever you are instructed to do so by airport or airline staff. If your device offers a ‘flight mode’ or similar feature, consult airline staff as to its use in flight.

Safety in Hospitals

Wireless devices transmit radio frequency energy and may affect medical electrical equipment. Wireless devices should be switched off wherever you are requested to do so in hospitals, clinics or health care facilities.

These requests are designed to prevent possible interference with sensitive medical equipmet.

Pacemakers

Pacemaker manufacturers recommended that a minimum of 15cm (6 inches) be maintained between a handheld wireless device and a pacemaker to avoid potential interference with the pacemaker. These recommendations are consistent with independent research and recommendations by Wireless Technology Research.

Persons with Pacemakers:

• Should ALWAYS keep the device more than 15cm (6 inches) from their pacemaker when turned ON.

• Should not carry the device in a breast pocket.

• Should use the ear furthest from the pacemaker to minimize the potential for interference

• If you have any reason to suspect that interference is taking place, turn OFF your device.

Other Medical Devices

Please consult your physician or the manufacturer of the medical device, to determine if the operation of your wireless product may interfere with the medical device.

Zebra Technologies Corporation • Lincolnshire, IL U.S.A.

Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered trademark of Symbol Technologies, Inc., a Zebra Technologies company. © 2015 Symbol Technologies, Inc.

72-151247-03 Revision A March 2015

Lietuvių: ES vartotojams: visi gaminiai, pasibaigus jų eksploatacijos laikui, turi būti grąžinti utilizuoti į kompaniją „Zebra“. Daugiau informacijos, kaip grąžinti gaminį,

rasite: http://www.zebra.com/weee.

Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Zebra vállalathoz kell eljuttatni újrahasznosítás céljából. A termék visszajuttatásának módjával kapcsolatos tudnivalókért látogasson el a http://www.zebra.com/weee weboldalra. Malti: Għal klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-aħħar tal-ħajja ta' l-użu tagħhom, iridu jiġu rritornati għand Zebra għar-riċiklaġġ. Għal aktar tagħrif dwar kif għandek tirritorna l-prodott, jekk jogħġbok żur: http://www.zebra.com/weee. Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun levensduur naar Zebra te worden teruggezonden voor recycling. Raadpleeg http://www.zebra.com/weee voor meer informatie over het terugzenden van

producten. Polski: Klienci z obszaru Unii Europejskiej: Produkty wycofane z eksploatacji

nale¿y zwróciæ do firmy Zebra w celu ich utylizacji. Informacje na temat zwrotu produktów znajduj¹ siê na stronie internetowej http://www.zebra.com/weee. Português: Para clientes da UE: todos os produtos no fim de vida devem ser devolvidos à Zebra para reciclagem. Para obter informações sobre como devolver o produto, visite: http://www.zebra.com/weee. Românesc: Pentru clienţii din UE: Toate produsele, la sfârşitul duratei lor de funcţionare, trebuie returnate la Zebra pentru reciclare. Pentru informaţii despre returnarea produsului, accesaţi: http://www.zebra.com/weee. Slovenčina: Pre zákazníkov z krajín EU: Všetky výrobky musia byť po uplynutí doby ich životnosti vrátené spoločnosti Zebra na recykláciu. Bližšie informácie o vrátení výrobkov nájdete na: http://www.zebra.com/weee.

Slovenski:

Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti

podjetju Zebra za reciklažo. Za informacije o vraèilu izdelka obišèite:

http://www.zebra.com/weee.

Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava kierrätettäväksi Zebra-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja tuotteen

palauttamisesta on osoitteessa http://www.zebra.com/weee.

Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste returneras till Zebra för återvinning. Information om hur du returnerar produkten

finns på http://www.zebra.com/weee.

Türkçe: AB Müşterileri için: Kullanım süresi dolan tüm ürünler geri dönüştürme için Zebra'ya iade edilmelidir. Ürünlerin nasıl iade edileceği hakkında bilgi için lütfen şu adresi ziyaret edin: http://www.zebra.com/weee.

Green Slow Flash Green Fast Flash Red and Green Flash

Scanner charging at a slow rate (used when cradle is powered by host cable)

REGULATORY INFORMATION

RF Exposure Guidelines

Safety Information Reducing RF Exposure – Use Properly

Only operate the device in accordance with the instructions supplied.

International

The device complies with internationally recognized standards covering human exposure to electromagnetic fields from radio devices. For information on “International” human exposure to eletromagnetic fields refer to the Zebra Declaration of Conformity (DoC) at http://www.zebra.com/doc.

EU - Handheld Devices

To comply with EU RF exposure requirements, this device must be operated in the hand with a minimum separation distance of 20cm or more from a person’s body. Other operating configurations should be avoided.

US and Canada - Handheld Devices

To comply with FCC RF exposure requirements, this device must be operated in the hand with a minimum separation distance of 20 cm or more from a person’s body. Other operating configurations should be avoided.

Batteries

Taiwan - Recycling

EPA (Environmental Protection Administration) requires dry battery producing or importing firms in accordance with Article 15 of the Waste Disposal Act are required to indicate the recycling marks on the batteries used in sales, giveaway or promotion. Contact a qualified Taiwanese recycler for proper battery disposal.

Battery Information

Zebra rechargeable battery packs are designed and constructed to the highest standards within the industry. However, there are limitations to how long a battery can operate or be stored before needing replacement. Many

factors affect the actual life cycle of a battery pack, such as heat, cold, harsh environmental conditions and severe drops.

When batteries are stored over six (6) months, some irreversible deterioration in overall battery quality may occur. Store batteries at half of full charge in a dry, cool place, removed from the equipment to prevent loss of capacity, rusting of metallic parts and electrolyte leakage. When storing batteries for one year or longer, the charge level should be verified at least once a year and charged to half of full charge.

Replace the battery when a significant loss of run time is detected. Standard warranty period for all Zebra batteries is 12 months, regardless if the battery was purchased separately or

included as part of the mobile computer or bar code scanner.

Battery Safety Guidelines

• The area in which the units are charged should be clear of debris and combustible materials or chemicals. Particular care should be taken where the device is charged in a non commercial environment.

• Follow battery usage, storage, and charging guidelines found in the user's guide.

• Improper battery use may result in a fire, explosion, or other hazard.

• To charge the mobile device battery, the battery and charger temperatures must be between +32 º F and +104 º F (0 º C and +40 º C)

• Do not use incompatible batteries and chargers. Use of an incompatible battery or charger may present a risk of fire, explosion, leakage, or other hazard. If you have any questions about the compatibility of a battery or a charger, contact Zebra support.

• For devices that utilize a USB port as a charging source, the device shall only be connected to products that bear the USB-IF logo or have completed the USB-IF compliance program.

• Do not disassemble or open, crush, bend or deform, puncture, or shred.

• Severe impact from dropping any battery-operated device on a hard surface could cause the battery to overheat.

• Do not short circuit a battery or allow metallic or conductive objects to contact the battery terminals.

• Do not modify or remanufacture, attempt to insert foreign objects into the battery, immerse or expose to water or other liquids, or expose to fire, explosion, or other hazard.

• Do not leave or store the equipment in or near areas that might get very hot, such as in a parked vehicle or near a radiator or other heat source. Do not place battery into a microwave oven or dryer.

• Battery usage by children should be supervised.

• Please follow local regulations to promptly dispose of used re-chargeable batteries.

• Do not dispose of batteries in fire.

• Seek medical advice immediately if a battery has been swallowed.

• In the event of a battery leak, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with large amounts of water and seek medical advice.

• If you suspect damage to your equipment or battery, contact Zebra support to arrange for inspection.

Radio Frequency Interference Requirements - FCC

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Zebra reserves the right to make changes to any product to improve reliability, function, or design. Zebra does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein. No license is granted, either expressly or by implication, estoppel, or otherwise under any patent right or patent, covering or relating to any combination, system, apparatus, machine, material, method, or process in which Zebra products might be used. An implied license exists only for equipment, circuits, and subsystems contained in Zebra products.

This Zebra Product may include Zebra Software, Commercial Third Party Software, and Publicly Available software. Refer to Product Reference Guide for complete copyright, conditions and disclaimer information.

Tested to comply with FCC Standards

FOR HOME OR OFFICE USE

Red Flash

Scanner charging at a fast rate (used when cradle is powered from external power supply)

Charging problem See

Product Reference Guide for more

information

Temperature fault

Recommended Usage Guide

Radio Transmitters (Part 15)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that maycause undesired operation.

Radio Frequency Interference Requirements – Canada

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Marking and European Economic Area (EEA)

Bluetooth® Wireless Technology for use through the EEA has the following restrictions:

• Maximum radiated transmit power of 100mW EIRP in the frequency range 2.400 -2.4835 GHz

Stat Statement of Compliance

Zebra hereby, declares that this device is in compliance with the essential requirements and other relevant provisions of Directives 1995/5/EC and 2011/65/EU. Declaration of Conformities may be obtained from http://www.zebra.com/doc.

Japan (VCCI) - Voluntary Control Council for Interference

この装置は、情報処理装置等電波障害自主規制協議会（ＶＣＣＩ）の基準に基づくクラスB情報技術装置です。この装置は、家庭環境で使用することを目的としていますが、この装置がラジオやテレビジョン受信機に近接して使用されると、受信障害を引き起こすことがあります。取扱説明書に従って正しい取り扱いをして下さい。

This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual.

Korean Warning Statement for Class B ITE

Other Countries

Declarações Regulamentares para DS3578 BRAZIL

NOTA: A marca de certificação se aplica ao Equip. de Radiação Restrita, modelo DS3578. Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário.” Para maiores consultas sobre ANATEL consulte o site: www.anatel.gov.br

CHILE

“Este equipo cumple con la Resolución No 403 de 2008, de la Subsecretaria de telecomunicaciones, relativa a radiaciones electromagnéticas.”.

China

Taiwan

臺灣低功率電波輻射性電機管理辦法第十二條經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。

第十四條低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電通信。

低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

Korea

For a radio equipment using 2400~2483.5MHz or 5725~5825MHz, the following two expression should be displayed ;

당해 무선설비는 운용 중 전파혼신 가능성이 있음 당해 무선설비 는전파혼 신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없습니다.

Mexico

Restrict Frequency Range to: 2.450 - 2/4835 GHz.

Laser Devices

Complies with 21CFR1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, June 24, 2007 and EN60825-1:2007 and IEC 60825-1(ED.2). The laser classification is marked on one of the labels on the device. Class 1 Laser devices are not considered to be hazardous when used for their intended purpose. The following statement is required to comply with US and international regulations: Caution: Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous laser light exposure. Class 2 laser scanners use a low power, visible light diode. As with any very bright light source, such as the sun, the user should avoid staring directly into the light beam. Momentary exposure to a Class 2 laser is not known to be harmful.

CAUTION - CLASS 2 LASER LIGHT WHEN OPEN. DO NOT STARE

ATTENTION-LUMIÈR E LASER EN CAS D 'OUVERTURE .

INTO THE BEAM. NE PA S REGARDER DANS LE FAISC EAU. VORSICHT - LASER LICHT KLA SSE 2, WENN ABDE CKUNG GEÖFFN ET. NI CHT DEM STRAH BLICKEN .

R32626

條碼掃描器

CCXXxxYYyyyZzW

003WWA110475

0168

MODEL:DS3578

FCC ID: H9PDS3578

IC: 1549D-DS3578

COMPLIES WITH 21CFR1040.10 AND 1040.11 EXCEPT FOR DEVIATIONSPURSUANT TO LASER NOTICE No. 50, DATED

JUNE 24, 2007, EN60825-1:2007 AND IEC 60825-1(ED.2) THIS CLASS B DIGITALAPPARATUS COMPLIES WITH

CANADIAN ICES-103. CET APPAREIL NUMÉRIQUE DE LA

CLASSE B EST CONFORME À LA NORME NMB-003 DU

CANADA.

SN BAR CODE

KCC-CMM-MIN-DS3578

CMIIT ID: XXXXYYZZ

P/N: DS3578-XXXXXXXXXX

(S)SN: XXXXXXXXXXXXX

MFD: XXXXXXX

MADE IN XXXXXX XXXX

BD_ADDR: XXXXXXXXXXXXX

http://www.zebra.com/ds3578

Zebra DS3578 Quick Start Manual

Specifications and Main Features

Frequently Asked Questions

User Manual