Zebra Symbol CS4070-HC Companion Scanner CHS5000 Wall Mount Bracket Installation Guide English
© 2015 Symbol Technologies, Inc.
72-102668-02 Revision A — February 2015
1A
2A
3A
Flanges
Mounting
tabs (4)
CHS5000-8000CR
1B
2B
3B
SAC5000-8000CR (2)
Zebra reserves the right to make changes to any product to improve reliability, function, or
design.
Zebra does not assume any product liability arising out of, or in connection with, the application
or use of any product, circuit, or application described herein.
No license is granted, either expressly or by implication, estoppel, or otherwise under any
patent right or patent, covering or relating to any combination, system, apparatus, machine,
material, method, or process in which Zebra products might be used. An implied license exists
only for equipment, circuits, and subsystems contained in Zebra products.
Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is
a registered trademark of Symbol Technologies, Inc., a Zebra Technologies company.
Warranty
For the complete Zebra hardware product warranty statement, go to:
http://www.zebra.com/warranty.
Refer to the CA50 Client/UCA Server Developer Guide (p/n 72E-93914-xx) for detailed product
information. For the latest guide, visit: http://www.zebra.com/support.
Zebra Technologies Corpor ation
Lincolnshire, IL U.S.A.
http://www.zebra.com
Zebra and the Zebra head graphic are registered trademarks of ZIH Corp.
The Symbol logo is a registered trademark of Symbol Technologies, Inc.,
a Zebra Technologies company.
© 2015 Symbol Technologies, Inc.
Wall Mount Bracket Kit
Installation Guide
for CHS5000-8000CR & SAC5000-8000CR Cradles
mounting to the wall type.
Ensure to use additional wall mount ing hardware, as needed, for safe
3. Use six screws to mount the bracket t o a wall (diagrams 3A and 3B).
(diagram 2B).
Phillips screw in each flange and tighten one flange to each cradle
NOTE When mounting two eight-slot battery chargers, use one .5”
tighten until the cradle is securely attached to the bracket (diagram 2A).
2. Screw two .5” Phillips screws (supplied) into the two bracket flanges and
mounting tabs into each battery charger (diagram 1B).
NOTE When mounting two eight-slot battery chargers, slide two bracket
align with the screw holes in the cradle.
cradle as shown in diagram 1A. Ensure the screw holes in the bracket flanges
1. Slide the four bracket mounting tabs into the receptacles on the bottom of the
charger, or two SAC5000-8000CR (eight-slot) ba ttery chargers (as pictured).
Follow the steps below to mount one CHS5000-8000CR (eight-slot) CA50
studs whenever possible.
wall type (i.e. plaster, drywall, concrete, etc.). Mount to wood
mounting, it is essential to us e wall anchors ap propriate to the
appropriate wall mounting hardware for installation. For safe
For safety and stability, it is recommended that you use the
mounting the bracket on a wall.
mounting bracket only. The screws are not intended for
WARNING! U se the screws supplied in this kit to attach the cradle(s) to the
Mounting Instructions
• Two black .5” Phillips round head, thread cutting screws.
• KT-102375-01R Mounting Bracket
Included Hardware
(p/n 72E-93914-xx) for detailed product information.
NOTE Refer to the CA50 Client/UCA Server Developer Guide
(eight-slot) battery chargers.
with one CHS5000-8000CR (eight-slot) CA50 charger, or two SAC5000-8000CR
This guide provides instructions for mounting the KT-102375-01R bracket for use
Introduction
Loading...