RS5100
to Laser Notice No. 50,
dated June 24, 2007 and
IEC/EN 60825-1:2014
Complies with 21CFR 10
40.10 and 1040.11 except
for deviations pursuant
Regulatory Guide
MN-003560-02EN Rev. A - 04/20
Zebra Technologies | 3 Overlook Point | Lincolnshire, IL 60069 USA
www.zebra.com
ZEBRA and the stylized Zebra head are trademarks of Zebra
Technologies Corporation, registered in many jurisdictions worldwide.
All other trademarks are the property of their respective owners. ©2020
Zebra Technologies Corporation and/or its affiliates. All rights reserved.
Warranty
For the complete Zebra hardware product warranty
statement, go to:
http://www.zebra.com/warranty.
Service Information
Before you use the unit, it must be configured to operate in
your facility’s network and run your applications.
If you have a problem running your unit or using your
equipment, contact your facility’s Technical or Systems
Support. If there is a problem with the equipment, they will
contact the Zebra Global Customer Support at
http://www.zebra.com/support.
For the latest version of this guide go to: http://
www.zebra.com/support.
Regulatory Information
This device is approved under Zebra Technologies
Corporation.
This guide applies to Model Number RS5100.
All Zebra devices are designed to be compliant with the rules
and regulations in the locations they are sold and will be
labeled as required.
Local language translations are available at the following
website: zebra.com/support
Any changes or modifications to Zebra equipment, not
expressly approved by Zebra could void the user’s authority
to operate the equipment.
Declared maximum operating temperature: 50°C.
.
CAUTION
Only use Zebra approved and UL Listed
accessories, battery packs and battery chargers.
Do NOT attempt to charge damp/wet mobile computers or
batteries. All components must be dry before connecting to
an external power source.
Bluetooth® Wireless
Technology
This is an approved Bluetooth® product. For more
information or to view the End Product Listing, please visit
bluetooth.org/tpg/listings.cfm
.
Frequency of Operation –
FCC and IC
Health and Safety
Recommendations
Ergonomic
Recommendations
CAUTION In order to avoid or minimize the
potential risk of ergonomic injury, follow the
recommendations below. Consult with your local
Health & Safety Manager to ensure that you are
adhering to your company's safety programs to prevent
employee injury.
• Reduce or eliminate repetitive motion
• Maintain a natural position
• Reduce or eliminate excessive force
• Keep objects that are used frequently within easy reach
• Perform tasks at correct heights
• Reduce or eliminate vibration
• Reduce or eliminate direct pressure
• Provide adjustable workstations
• Provide adequate clearance
• Provide a suitable working environment
• Improve work procedures.
Warnings for Use of
Wireless Devices
CAUTION Please observe all warning notices with
regard to the usage of wireless devices.
Potentially Hazardous
Atmospheres – Vehicles
Use
You are reminded of the need to observe restrictions on the
use of radio devices in fuel depots, chemical plants etc. and
areas where the air contains chemicals or particles such as
grain, dust, or metal powders and any other area where you
would normally be advised to turn off your vehicle engine.
Safety in Hospitals
Wireless devices transmit radio frequency energy and may
affect medical electrical equipment.
Wireless devices should be switched off wherever you are
requested to do so in hospitals, clinics or healthcare facilities.
These requests are designed to prevent possible interference
with sensitive medical equipment.
Pacemakers
Pacemaker manufacturers recommended that a minimum of
15 cm (6 inches) be maintained between a handheld wireless
device and a pacemaker to avoid potential interference with
the pacemaker. These recommendations are consistent with
independent research and recommendations by Wireless
Technology Research.
Persons with Pacemakers:
• Should ALWAYS keep the device more than 15cm (6
inches) from their pacemaker when turned ON.
• Should not carry the device in a breast pocket.
• Should use the ear furthest from the pacemaker to
minimise the potential for interference.
• If you have any reason to suspect that interference is
taking place, turn OFF your device.
Other Medical Devices
Please consult your physician or the manufacturer of the
medical device to determine if the operation of your wireless
product may interfere with the medical device.
RF Exposure Guidelines
Safety Information
Reducing RF Exposure – Use
Properly
Only operate the device in accordance with the instructions
supplied.
International
The device complies with internationally recognized
standards covering human exposure to electromagnetic
fields from radio devices. For information on “International”
human exposure to electromagnetic fields refer to the Zebra
Declaration of Conformity (DoC) at: zebra.com/doc
For further information on the safety of RF energy from
wireless devices - see zebra.com/responsibility
Corporate Responsibility.
Europe
Handheld Devices
This device was tested for typical body worn operation. Use
only Zebra tested and approved belt-clips, holsters, and
similar accessories to ensure EU Compliance.
.
located under
US and Canada
Handheld Devices
This device was tested for typical body worn operation. Use
only Zebra tested and approved belt-clips, holsters, and
similar accessories to ensure FCC Compliance. The use of
third-party belt-clips, holsters, and similar accessories may
not comply with FCC RF exposure compliance requirements,
and should be avoided.
Laser Devices
Class 2 laser scanners use a low power, visible
light diode. As with any very bright light source such as the
sun, the user should avoid staring directly into the light beam.
Momentary exposure to a Class 2 laser is not known to be
harmful.
Caution: Use of controls, adjustments or
performance of procedures other than those
specified herein may result in hazardous laser light
exposure.
Scanner Labeling
Label Reads:
LASER LIGHT - DO NOT STARE INTO BEAM. CLASS 2
LASER PRODUCT.
Complies with 21CFR 1040.10 and 1040.11 except for
deviations pursuant to Laser Notice No. 50, dated June 24,
2007 and IEC/EN 60825-1:2014.
LED Devices
Classified as 'EXEMPT RISK GROUP' according to IEC
62471:2006 and EN 62471:2008.
Pulse duration: CW
Batteries
Taiwan - Recycling
EPA
(Environmental
Protection
Administration)
requires dry
battery
producing or
importing firms
in accordance
with Article 15 of the Waste Disposal Act are required to
indicate the recycling marks on the batteries used in sales,
giveaway or promotion. Contact a qualified Taiwanese
recycler for proper battery disposal.
Battery Information
CAUTION Risk of explosion if battery
is replaced by an incorrect type.
Dispose of batteries according to
instructions.
Use only Zebra approved batteries. Accessories which have
battery charging capability are approved for use with the
following battery models:
Model BT-000397 (3.7 Vdc, 480 mAh)
Model BT-000398 (3.7 Vdc, 735 mAh).
Zebra approved rechargeable battery packs are designed
and constructed to the highest standards within the industry.
However, there are limitations as to how long a battery can
operate or be stored before needing replacement. Many
factors affect the actual life cycle of a battery pack such as
heat, cold, harsh environmental conditions, and severe
drops.
When batteries are stored over six months, some irreversible
deterioration in overall battery quality may occur. Store
batteries at half of full charge in a dry, cool place, removed
from the equipment to prevent loss of capacity, rusting of
metallic parts, and electrolyte leakage. When storing
batteries for one year or longer, the charge level should be
verified at least once a year and charged to half of full charge.
Replace the battery when a significant loss of run time is
detected.
Standard warranty period for all Zebra batteries is one year,
regardless if the battery was purchased separately or
included as part of the mobile computer or bar code scanner.
For more information on Zebra batteries, please visit:
www.zebra.com/batterybasics
.
Battery Safety Guidelines
The area in which the units are charged should be clear of
debris and combustible materials or chemicals. Particular
care should be taken where the device is charged in a noncommercial environment.
• Follow battery usage, storage, and charging guidelines
found in the user's guide.
• Improper battery use may result in a fire, explosion, or
other hazard.
• To charge the mobile device battery, the battery and
charger temperatures must be between +41 ºF and +104
ºF (5 ºC and +40 ºC)
• Do not use incompatible batteries and chargers. Use of
an incompatible battery or charger may present a risk of
fire, explosion, leakage, or other hazard. If you have any
questions about the compatibility of a battery or a
charger, contact Zebra support.
• For devices that utilize a USB port as a charging source,
the device shall only be connected to products that bear
the USB-IF logo or have completed the USB-IF
compliance program.
• Do not disassemble or open, crush, bend or deform,
puncture, or shred.
• Severe impact from dropping any battery-operated
device on a hard surface could cause the battery to
overheat.
• Do not short circuit a battery or allow metallic or
conductive objects to contact the battery terminals.
• Do not modify or remanufacture, attempt to insert foreign
objects into the battery, immerse or expose to water or
other liquids, or expose to fire, explosion, or other
hazard.
• Do not leave or store the equipment in or near areas that
might get very hot, such as in a parked vehicle or near a
radiator or other heat source. Do not place battery into a
microwave oven or dryer.
• Battery usage by children should be supervised.
• Please follow local regulations to promptly dispose of
used re-chargeable batteries.
• Do not dispose of batteries in fire.
• Seek medical advice immediately if a battery has been
swallowed.
• In the event of a battery leak, do not allow the liquid to
come in contact with the skin or eyes. If contact has been
made, wash the affected area with large amounts of
water and seek medical advice.
• If you suspect damage to your equipment or battery,
contact Zebra support to arrange for inspection.
Radio Frequency
Interference RequirementsFCC
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this
device must accept any interference received including
interference that may cause undesired operation.
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15
of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and
receiver
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician
for help.
Radio Frequency Interference
Requirements - Canada
Innovation, Science and Economic Development Canada
ICES-003 Compliance Label: CAN ICES-3 (B)/NMB-3(B)
Radio Transmitters
This device complies with Industry Canada's licence-exempt
RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and (2) This
device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie
Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes: (1)
l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur
de l'appareil doit accepter tout brouillage radio électrique subi
même si le brouillage est susceptible d'en compromettre le
fonctionnement.
Marking and European
Economic Area (EEA)
Statement of Compliance
Zebra hereby declares that this radio equipment is in
compliance with the Directives, 2014/53/EU and 2011/65/EU.
The full text of the UE Declaration of Conformity is available
at the following internet address: www.zebra.com/doc
.
Korea Warning Statement
for Class B ITE
기 종 별 사 용 자 안 내 문
B 급 기기
(가정용 방송통신기자재)
이 기기는
가정용 (B 급 )
전자파적합기기로
서 주로
가정에서
사용하는 것을
목적으로 하며 ,
모든 지역에서
사용할 수
있습니다 .
Other Countries
Brazil
Este equipamento não tem direito à proteção contra
interferência prejudicial e não pode causar interferência em
sistemas devidamente autorizados
Chile
Conforme a Resolución 755 parte j.1), se ajustará el
dispositivo a operar en interiores en las siguientes bandas
con una potencia máxima radiada no superior a 150mW:
2.400 a 2.483,5MHz
Para la tecnología NFC en la banda 13.553 a 13.567 kHz, la
intensidad de campo eléctrico no excederá 20 mV/m a 30
metros, conforme a Resolucion 755 parte Art 1. e).
China
通过访问以下网址可下载当地语言支持的产品说明书
www.zebra.com/support
锂电池安全警示语 :
警告：请勿拆装，短路，撞击，挤压或者投入火中
注意：如果电池被不正确型号替换，或出现鼓胀，会存在爆炸
及其他危险
请按说明处置使用过的电池
电池浸水后严禁使用
合格证：
合 格 证
Eurasian Customs Union
Евразийский Таможенный Союз
Данный продукт соответствует требованиям знака EAC.
Mexico
La operación de este equipo está sujeta a las siguientes dos
condiciones: (1) es posible que este equipo o dispositivo no
cause interferencia perjudicial y (2) este equipo o dispositivo
debe aceptar cualquier interferencia, incluyendo la que
pueda causar su operación no deseada.
Taiwan
臺灣
低功率電波輻射性電機管理辦法
第十二條
經型式認證合格之低功率射頻電機，非經許可，公司、商號或
使用者均不得擅自變更頻率、加大功率或變更原設計之特性及
功能。
第十四條
低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經
發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續
使用。
前項合法通信，指依電信法規定作業之無線電通信。
低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻
射性電機設備之干擾。
應避免影響附近雷達系統之操作
公司資訊
台灣斑馬科技股份有限公司 / 台北市信義區松高路 9 號 13 樓
Ukraine
Дане обладнання відповідає вимогам технічного
регламенту № 1057, 2008 на обмеження щодо
використання деяких небезпечних речовин в електричних
та електронних пристроях.
Thailand
เครื่ องโทรคมนาคมและอุ ปกรณ์ นี้
มีความสอดคล้องตามข้อกำหนดของ กทช.
Turkish WEEE Statement of
Compliance
EEE Yönetmeliğine Uygundur.
Waste Electrical
and Electronic
Equipment (WEEE)
English: For EU Customers: All products at the end of their
life must be returned to Zebra for recycling. For information
on how to return product, please go to: http://
www.zebra.com/weee.
Français: Clients de l'Union Européenne: Tous les produits
en fin de cycle de vie doivent être retournés à Zebra pour
recyclage. Pour de plus amples informations sur le retour de
produits, consultez : http://www.zebra.com/weee.
Español: Para clientes en la Unión Europea: todos los
productos deberán entregarse a Zebra al final de su ciclo de
vida para que sean reciclados. Si desea más información
sobre cómo devolver un producto, visite: http://
www.zebra.com/weee.
Bulgarish: За клиенти от ЕС: След края на полезния им
живот всички продукти трябва да се връщат на Zebra за
рециклиране. За информация относно връщането на
продукти, моля отидете на адрес: http://www.zebra.com/
weee.
Deutsch: Für Kunden innerhalb der EU: Alle Produkte
müssen am Ende ihrer Lebensdauer zum Recycling an Zebra
zurückgesandt werden. Informationen zur Rücksendung von
Produkten finden Sie unter
http://www.zebra.com/weee.
Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al
termine del rispettivo ciclo di vita devono essere restituiti a
Zebra al fine di consentirne il riciclaggio. Per informazioni
sulle modalità di restituzione, visitare il seguente sito Web:
http://www.zebra.com/weee.
Português: Para clientes da UE: todos os produtos no fim de
vida devem ser devolvidos à Zebra para reciclagem. Para
obter informações sobre como devolver o produto, visite:
http://www.zebra.com/weee.
Nederlands: Voor klanten in de EU: alle producten dienen
aan het einde van hun levensduur naar Zebra te worden
teruggezonden voor recycling. Raadpleeg
http://www.zebra.com/weee voor meer informatie over het
terugzenden van producten.
Polski: Klienci z obszaru Unii Europejskiej: Produkty
wycofane z eksploatacji należy zwrócić do firmy Zebra w celu
ich utylizacji. Informacje na temat zwrotu produktów znajdują
się na stronie internetowej http://www.zebra.com/weee.
Čeština: Pro zákazníky z EU: Všechny produkty je nutné po
skonèení jejich životnosti vrátit spoleènosti Zebra k recyklaci.
Informace o zpùsobu vrácení produktu najdete na webové
stránce: http://www.zebra.com/weee.
Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes
tagastada taaskasutamise eesmärgil Zebra'ile.
Lisainformatsiooni saamiseks toote tagastamise kohta
külastage palun aadressi: http://www.zebra.com/weee.
Magyar: Az EU-ban vásárlóknak: Minden tönkrement
terméket a Zebra vállalathoz kell eljuttatni újrahasznosítás
céljából. A termék visszajuttatásának módjával kapcsolatos
tudnivalókért látogasson el a http://www.zebra.com/weee
weboldalra.
Svenska: För kunder inom EU: Alla produkter som uppnått
sin livslängd måste returneras till Zebra för återvinning.
Information om hur du returnerar produkten finns på http://
www.zebra.com/weee.
Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet
on palautettava kierrätettäväksi Zebra-yhtiöön, kun tuotetta ei
enää käytetä. Lisätietoja tuotteen palauttamisesta on
osoitteessa http://www.zebra.com/weee.
Dansk: Til kunder i EU: Alle produkter skal returneres til
Zebra til recirkulering, når de er udtjent. Læs oplysningerne
om returnering af produkter på:
http://www.zebra.com/weee.
Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο
τέλος της διάρκειας ζωής τους, πρέπει να επιστρέφονται στην
Zebra για ανακύκλωση. Για περισσότερες πληροφορίες
σχετικά με την επιστροφή ενός προϊόντος, επισκεφθείτε τη
διεύθυνση
http://www.zebra.com/weee στο Διαδίκτυο.
Malti: Għal klijenti fl-UE: il-prodotti kollha li jkunu waslu flaħħar tal-ħajja ta' l-użu tagħhom, iridu jiġu rritornati għand
Zebra għar-riċiklaġġ. Għal aktar tagħrif dwar kif għandek
tirritorna l-prodott, jekk jogħġbok żur: http://www.zebra.com/
weee.
Românesc: Pentru clienţii din UE: Toate produsele, la
sfârşitul duratei lor de funcţionare, trebuie returnate la Zebra
pentru reciclare. Pentru informaţii despre returnarea
produsului, accesaţi: http://www.zebra.com/weee.
Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku
življenjske dobe vrniti podjetju Zebra za reciklažo. Za
informacije o vračilu izdelka obiščite:
http://www.zebra.com/weee.
Slovenčina: Pre zákazníkov z krajín EU: Všetky výrobky
musia byť po uplynutí doby ich životnosti vrátené spoločnosti
Zebra na recykláciu. Bližšie informácie o vrátení výrobkov
nájdete na: http://www.zebra.com/weee.
Lietuvių: ES vartotojams: visi gaminiai, pasibaigus jų
eksploatacijos laikui, turi būti grąžinti utilizuoti į kompaniją
„Zebra“. Daugiau informacijos, kaip grąžinti gaminį, rasite:
http://www.zebra.com/weee.
Latviešu: ES klientiem: visi produkti pēc to kalpošanas mūža
beigām ir jānogādā atpakaļ Zebra otrreizējai pārstrādei. Lai
iegūtu informāciju par produktu nogādāšanu Zebra, lūdzu,
skatiet: http://www.zebra.com/weee.
Türkçe: AB Müşterileri için: Kullanım süresi dolan tüm
ürünler geri dönüştürme için Zebra'ya iade edilmelidir.
Ürünlerin nasıl iade edileceği hakkında bilgi için lütfen şu
adresi ziyaret edin: http://www.zebra.com/weee.
CMM Disclosure
部件名称
(Parts)
金属部件
(Metal Parts)
电路模块
(Circuit
Modules)
电缆及电缆组
件
(Cables and
Cable
Assemblies)
有害物质
(Cr(V
I))
多溴联
苯
(PBB)
铅
(Pb)汞(Hg)镉(Cd)六价铬
O O O O O O
X O O O O O
O O O O O O
多溴二苯
醚
(PBDE)
部件名称
(Parts)
塑料和聚合物
部件
(Plastic and
Polymeric
Parts)
光学和光学组
件
(Optics and
Optical
Components)
电池
(Batteries)
本表格依据 SJ/T 11364 的规定编制。
O: 表示该有害物质在该部件所有均质材料中的含量均在 GB/
T 26572 规定的限量要求以下。
X: 表示该有害物质至少在该部件的某一均质材料中的含量超
出GB/T 26572 规定的限量要求。(企业可在此处，根据实
际情况对上表中打“×”的技术原因进行进一步说明。）
This table was created to comply with China RoHS
requirements.
有害物质
(Cr(V
I))
多溴联
苯
(PBB)
铅
(Pb)汞(Hg)镉(Cd)六价铬
O O O O O O
O O O O O O
O O O O O O
多溴二苯
醚
(PBDE)
Loading...