MN-004352-01EN_rs5100-glove-qsg-en.fm Page 11 Monday, October 25, 2021 3:32 PM
RS5100
Hand Mount Glove Quick
Start Guide
MN-004352-01EN Rev. A - 10/2021
Zebra Technologies |
3 Overlook Point |
Lincolnshire, IL 60069 USA
www.zebra.com
ZEBRA and the stylized Zebra head are
trademarks of Zebra Technologies Corp.,
registered in many jurisdictions
worldwide. All other trademarks are the
property of their respective owners. ©
2021 Zebra Technologies Corp. and/or
its affiliates. All rights reserved.
Hand Mount Glove
The Hand Mount Glove allows the RS5100 to be worn on
the back of your hand and provides a remote finger
trigger. It comes in multiple sizes to fit all and is available
for right-handed and left-handed users. You can
distinguish the size by the color of the stitching on the
glove.
• Small = white
• Medium = black
• Large = blue
To attach the hand mount glove to the hand mount
assembly, perform the following steps:
1. Install the glove to the back of hand assembly, if not
already installed (note the position for right hand user
or left hand user).
2. Position the hand mount glove on the hand.
3. Install the RS5100 onto the back of hand mount, if not
already installed.
Install Glove: Right Hand User
To install the glove to the back of hand assembly for a
right hand user:
1. Insert the trigger cable and button through the trigger
slot.
3. Insert the velcro strap through the right slot of the
mount and fasten the velcro strap end.
Install Glove: Left Hand User
To install the glove to the back of hand assembly for a left
hand user:
1. Insert the trigger cable and button through the trigger
slot.
3. Insert the velcro strap through the left slot of the mount
and fasten the velcro strap end.
Position Glove on Hand
To position the glove on the hand:
1. Slide your hand through the glove, with your thumb
through the smaller opening and your remaining four
fingers through the larger opening. Note the position for
a left-hand user and a right-hand user.
Warranty
For the complete Zebra hardware product warranty statement, go
to: zebra.com/warranty.
Service Information
Before you use the unit, it must be configured to operate in your
facility’s network and run your applications.
If you have a problem running your unit or using your equipment,
contact your facility’s Technical or Systems Support. If there is a
problem with the equipment, they will contact the Zebra Global
Customer Support at zebra.com/support.
For the latest version of this guide go to:
zebra.com/support.
Additional Information
For information on using the RS5100, refer to the RS5100 product
guide available at: zebra.com/support.
2. Insert the velcro strap through the left slot of the mount
and slide under the mount.
2. Insert the velcro strap through the right slot of the
mount and slide under the mount.
2. Adjust the strap to a comfortable position to fit securely
by tightening or loosening the strap.
3. Slide the strap through the buckle and secure the end
of the strap in place with the velcro.
NOTE: The snap under the strap is meant as a
safety breakaway and is not meant for
securing the strap.
MN-004352-01EN_rs5100-glove-qsg-en.fm Page 12 Monday, October 25, 2021 3:32 PM
4. Position the finger trigger button to rotate it so that the
button is easy access to your thumb and then fasten it in
place with the velcro.
5. Align the mount on the glove. To do this:
a. Lift the velcro strap holding the mount in place.
Install RS5100
To install the RS5100 onto the back of hand mount:
1. Align the contacts on the RS5100 assembly with the
contacts on the back of hand mount and engage the slot
(located at the top of the RS5100 on the backside) on
the RS5100 with the opening at the top of the back of
hand mount.
2. Push down on the RS5100 to snap into place.
Incorrect Installation
Detach RS5100
To detach the RS5100 from the back of hand mount:
1. Press the release buttons on both sides of the back of
hand mount using your thumb and middle finger.
To remove the electronics from the glove:
1. Unfasten the strap and detach the mount holding the
RS5100
2. Slide the mount off the strap.
b. Detach and lift the mount, which is holding the
RS5100.
c. Reposition the mount on the glove to align the mount
with your middle finger knuckle.
d. Fasten the velcro strap.
Correct Installation
2. Lift the RS5100 off the back of hand mount using your
index finger.
3. Remove the finger trigger button and cable from the
glove.
4. Use an approved cleaning agent or mild detergent on
the glove material only and air dry.
Cleaning the Glove
Before cleaning the glove, you must remove the
electronics from the glove.
Loading...